Panasonic NV-VP31 Operating instructions

Panasonic
Brand
Panasonic
Model
NV-VP31
Type
Operating instructions

This manual is also suitable for

Panasonic NV-VP31 is a VCR/DVD set that includes functions for both recording and DVD playback. This device will allow you to connect your TV and watch channels that you select on the device by using the buttons or the remote control that comes with the set. You can set the device to automatically tune to available TV stations with the Auto Setup function. In addition to watching TV, the Panasonic NV-VP31 also supports recording TV programs, allowing you to watch them later.

Panasonic NV-VP31 is a VCR/DVD set that includes functions for both recording and DVD playback. This device will allow you to connect your TV and watch channels that you select on the device by using the buttons or the remote control that comes with the set. You can set the device to automatically tune to available TV stations with the Auto Setup function. In addition to watching TV, the Panasonic NV-VP31 also supports recording TV programs, allowing you to watch them later.

Quick Start Guide
DVD/CD Player / Video Cassette Recorder
Model No.
NV-VP31EB/EBL
(Model suffix: 'EB' for UK model, 'EBL' for Ireland model)
Dear Customer,
May we take this opportunity to thank you for
purchasing this Panasonic Video
Cassette Recorder. Please use this Quick Start Guide
to help you set up your VCR/DVD. We would also
advise you to carefully study the operating instructions
and note the listed precautions before use.
DVD/CD Player /
Condensation Precaution
This VCR/DVD is not fitted with a condensation
sensor. If you bring in the VCR/DVD from a cold place,
e.g. a car, into a warm house, dew may form inside the
VCR/DVD. Do not switch it on for at least 1 hour.
Fit the Batteries into the
Remote Control
- 1 -
RQCAD0016 F18B04-0
Check that you have the accessories and items shown
Quick Start Guide
RQCAD0016 (This leaflet)
AC Mains Lead
RJA0044-3C
RF cable
Batteries for the
Remote Control
R6 size
Operating Instructions
RQTD0126-B
Guarantee Card
A
ccessories
Included
Remote control
EUR7720X20
AV
ENTER
TV
CH
VCR
INPUT SEL
ShowView
AUDIO
RESET/CANCEL
REC MODE
OFF-TIMER
PROG PLAY
I-TIMER
MENU
EXIT
JET REW
CH
AV LINK
EXT LINK
STATUS
A
B
RECTIMER
INDEX
VOL
TRACKING/V-LOCK
N2QAJB000088
1
2
3
4
5
6
7
8
9
0
PROG
/CHECK
PAUSE/SLOW
VCR/TV
* Some functions may not be
applicale to your VCR.
K2KF2BA00001, VJA0728-A
or K1TWACC00001
Direct Sales at Panasonic UK
!
Order accessory and consumable items for your product with ease and
confidence by telephoning our Customer Care Centre
Mon - Friday 9:00am - 5:30pm (Excluding public holidays).
!
Or go on line through our Internet Accessory ordering application at
www.panasonic.co.uk.
!
Most major credit and debit cards accepted.
!
All enquiries, transactions and distribution facilities are provided directly
by Panasonic UK Ltd.
!
It couldn´t be simpler!
!
Also available through our internet is direct shopping for a wide range
of finished products, take a browse on our website for further details.
Sales and Support Information
Customer Care Centre
!
For UK customers:
08705 357357.
!
For Republic of Ireland customers:
01 289 8333.
!
Visit our website for product
information www.panasonic.co.uk.
!
E-mail:
customer[email protected].
How to use this Guide
Page
Connecting with RF cable 2
VCR Auto Setup with RF cable
Connecting with 21-pin Scart cable 3
VCR Auto Setup with 21-pin Scart cable
Checking the Settings after Auto Setup 4
Removing Interference 5
Changing RF-output channel
DVD-QUICK SETUP 6
- 2 -
N
I
R
F
O
U
R
T
F
AV
1
TV
)
(
A
V
2
DE
R
/
D
E
CO
(
E
X
)
T
O
A
D
I
U
R
L
ED
O
V
I
O
A D
I
U
R
L
E
D OV
I
D D
/
V
R O
C
V
U
T
O
T
V
U
D
D
A
G
T L
A
DI
U
DI
I
O
P B
/
T
A
)
(
C
T
R
M
I
S E
M
T
A
O
C
L
P
I
VCR/DVD
4
2
AC IN
Aerial
RF IN
input
Aerial
RF OUT
output
AC mains lead
AC IN~
Aerial
AC mains socket
1
4 AC mains lead
4
Connecting with RF cable
Connect VCR and TV set to the
AC mains socket.
You can connect the VCR to your TV
set by using a RF cable.
Aerial input
RF coaxial cable
TV
2
Follow the steps described below.
3
1
Connect aerial to the RF IN (Aerial
input) connector of the VCR/DVD.
Connect the VCR/DVD´s RF OUT
(Aerial output) to the TV set’s
Aerial in connector.
Ensure TV Power is disconnected
from AC Mains socket.
Follow the steps for VCR Auto Setup.
3
VCR Auto Setup with RF cable (Automatic tuning)
!
Turn on your television set.
!
With the Stand-by/on switch turn on the VCR/DVD. Automatic tuning
for all available TV stations begins. Approximate duration is 5 minutes.
!
After Automatic tuning has finished, press EXIT. The Owner ID screen will
appear.
- While Auto Setup is running the first digit of the VCR display will flash.
After a while it will stop flashing and the RF output channel number will
be displayed.
- Select an unused channel pre-set on your TV and tune it to the RF
output channel number shown on the VCR display (or until you can
clearly see the Auto Setup screen). Store the new video playback
channel (refer to the instructions for your TV).
VCR Display
You can complete the Owner ID now or skip this step and do it later. To
do it later, press the EXIT button. Your VCR is now ready to use.
Optionally, you can have a QUICK SETUP following VCR Auto Setup for
the DVD player (page 6).
!
To set the Owner ID now, press the Numeric buttons or to enter
a four-digit PIN number.
!
Press , to correct the digit.
!
Make sure that you will remember the PIN number (make a note of it).
!
Press the ENTER button twice to confirm.
!
Enter the [Name], [House No] and [Postcode] in the same way.
!
Press the ENTER button to confirm each entry.
!
Press the EXIT button to leave the Owner ID screen.
!
You will now see the TV picture. Your VCR is now ready to use. Optionally,
you can have a QUICK SETUP following VCR Auto Setup for the DVD
player (page 6).
Owner ID
PIN number :
****
Name :
**************
House No :
***********
Postcode :
***********
:select : store
: return : exit
ENTER
MENU EXIT
You now have the opportunity
to enter your details and
help the police crack crime
see instruction book.
Owner ID
Datum / ZeitClock set
Time : 12 : 00 : 00
Date : 11. 6. 04
MANUAL
!
Press to set the correct time and date.
!
Press the ENTER button to finish this setting.
If the clock setting menu appears
(Auto clock set was not possible due to a weak signal)
D
Mind that a wrong date or time will influence the programmed
recording of TV programmes (don't forget to change summer
time and winter time).
D
In some cases, the RF output channel may interfere with the TV
stations transmitted in your area. This may prevent you from seeing the
On-Screen Display clearly. Please see page 5 for removing the
interference before restarting Auto Setup (page 35 of Operating
Instructions).
Auto Setup
: exit
EXIT
Tuning : Ch 21
- 3 -
AC mains socket
1
Connecting with 21-pin Scart cable (Fully wired)
Connect the VCR/DVD’s AV1 socket
(21-pin Scart socket) to the TV set’s
Scart In socket.
Connect VCR/DVD and TV set to
the AC mains socket.
4
2
Connect aerial to the RF IN (Aerial
input) connector of the VCR/DVD.
Follow the steps described below.
3
Connect the VCR/DVD´s RF OUT
(Aerial output) to the TV set’s
Aerial in connector.
Ensure TV Power is disconnected
from AC Mains socket.
1
Follow the steps for VCR Auto Setup.
R
N
F
I
T
R O
U
F
1
A
V
(
T
)
V
AV
2
OC
(
EDE D
R/
X)
T
E
D
U
IA
O
R
L
V
O
E
I
D
U
I
A O
D
R
L
O
E
I D
V
RDU
V
C
V
/
D
OT
D
O
T
DU
V
L
D I
TA
U
A I
O
I
G
D
T
P I T M
)
(
E
C
A
M
B S
R
/
L
O
A
TIC
P
VCR / DVD
5
5
4
3
2
AC IN
RF IN
Aerial input
AV1
21-pin Scart socket
RF OUT
Aerial output
AC mains lead
Aerial input
TV
AC mains lead
AC IN~
21-pin Scart cable
RF coaxial cable
Aerial
5
D
If Auto Setup has previously been completed the VCR will not start Auto Setup
automatically. In this case you can re-start Auto Setup again. See page 35 of
Operating Instructions.
D
If you want to cancel Auto Setup before it has finished, press the EXIT button.
You can restart Auto Setup again. See page 35 of Operating Instructions.
VCR Auto Setup with 21-pin Scart cable
(Automatic tuning)
Datum / ZeitClock set
Time : 12 : 00 : 00
Date : 11. 6. 04
MANUAL
!
Press to set the correct time and date.
!
Press the ENTER button to finish this setting.
If the clock setting menu appears
(Auto clock set was not possible due to a weak signal)
D
Mind that a wrong date or time will influence the programmed recording of TV
programmes (don't forget to change summer time and winter time).
You can complete the Owner ID now or skip this step and do it later. To do it
later, press the EXIT button. Your VCR is now ready to use. Optionally, you can
have a QUICK SETUP following VCR Auto Setup for the DVD player (page 6).
!
To set the Owner ID now, press the Numeric buttons or to enter a four-
digit PIN number.
!
Press , to correct the digit.
!
Make sure that you will remember the PIN number (make a note of it).
!
Press the ENTER button twice to confirm.
!
Enter the [Name], [House No] and [Postcode] in the same way.
!
Press the ENTER button to confirm each entry.
!
Press the EXIT button to leave the Owner ID screen.
!
You will now see the TV picture. Your VCR/DVD is now ready to use.
Optionally, you can have a QUICK SETUP following VCR Auto Setup for the
DVD player (page 6).
Owner ID
!
Turn on your television set.
!
With the Stand-by/on switch turn on the VCR/DVD.
Automatic tuning for all available TV stations begins.
Approximate duration is 5 minutes.
!
After Automatic tuning has finished, press EXIT.
The Owner ID screen will appear.
Owner ID
PIN number :
****
Name :
**************
House No :
***********
Postcode :
***********
:select : store
: return : exit
ENTER
MENU EXIT
You now have the opportunity
to enter your details and
help the police crack crime
see instruction book.
VCR Display
Auto Setup
: exit
EXIT
Tuning : Ch 21
- 4 -
!
Press the MENU button to display the OSD Main menu on the TV screen.
!
Press to select Tuning then press the ENTER button.
!
Press to select Manual then press the ENTER button to display the
list of tuned TV stations and confirm that all available TV stations have
been set correctly.
!
Press the EXIT button to exit the On Screen Display.
When the station names and/or channel numbers have not been set correctly,
see page 34 of Operating Instructions for details.
When no station has been found, confirm all connections of the VCR again
and restart the Auto Setup. See page 35 of Operating Instructions for details.
Checking the Settings
after Auto Setup
To confirm that the TV stations have been tuned
correctly by Auto Setup
Menu
Timer recording
Tuning
Clock set
Others
:select : access
: exit
ENTER
EXIT
Tuning
Manual
Auto Setup
Shipping condition
Owner ID
: select : access
: return : exit
ENTER
MENU EXIT
Tuning
Pos Name Ch Pos Name Ch
6 30
7 - - - - - - -
8 - - - - - - -
9 - - - - - - -
10 - - - - - - -
1 BBC1 22
2 BBC2 23
3 ITV 24
4 CH4 25
5 CH5 26
Tuning
Pos Name Ch Pos Name Ch
6 ITV 24
7 CH4 25
8 CH5 26
9 - - - - - - -
10 - - - - - - -
1 RTE1 2
2 NET2 4
3 TNG 6
4 BBC1 22
5 BBC2 23
TV Reception Channels
Example of UK model Example of Ireland model
EXIT
MENU
D
If station name is [ ]:
The asterisks indicate that a station was found during Auto Setup but has
not been named (due to weak signal).
The stations in the list with asterisk will need to be named manually see
page 34 of Operating Instructions.
D
If station name is [- - - -]:
The dashes represent unused channel positions.
The stations in the list with dashes will need to be set manually.
See page 33 of Operating Instructions.
The reception
channels are
different for UK
and Ireland.
TV screen
The picture with interference
On-Screen Display
Test pattern indication
Removing Interference / Changing RF-output channel
In some cases, interference (lines or patterning) or a very poor picture
may appear on the TV when the VCR is connected. If this happens,
follow the steps below to change the video playback channel (RF output
channel) to remove the interference.
!
Press the MENU button for more than 5 seconds. The RF output
channel number is displayed on the VCR display.
VCR Ch:28
The clear picture
!
Press ENTER to finish this setting.
!
Press the Numeric buttons or use the Channel (CH) button
to select a channel number, which differs by 2 or 3 from the
present channel number. (For example, if the original
channel number was 28, enter 31.)
21
68
(RF OFF)
...
!
Retune your TV until you receive the Test pattern. It may be necessary
to repeat steps above until you can see the Test pattern clearly.
If using a Scart cable please see the note below.
VCR display
Indication when the RF output
channel is 28 (example)
Indication after changing the RF
output channel to 31 (example)
Test pattern indication
VCR Ch:31
MENU
8 9
CH
TRACKING/V-LOCK
ENTER
!
Press MENU for about 5 seconds. The preset channel will be
displayed on the VCR-display.
!
Press channel select buttons CH or 0 to invoke [- -].
!
Confirm with ENTER.
D
Set the RF output channel of the VCR to [- -] (RF OFF) if the VCR is
connected to the TV via the 21-pin Scart cable.
- 5 -
The navigator keys of the remote control unit
allow you to move between menus and to accept
or change the selected settings.
Press ENTER to store a change.
Press RETURN to go back to the
previous screen.
Press SETUP to quit the menu.
Following , you can use the options of the
menu to make further settings.
Press RETURN or SETUP to quit the menu.
QUICK SETUP
Setup
Setup
See page 54 of Operating Instructions.
D
Please refer to the operating instructions of your TV set to read
more about the best settings.
DVD-QUICK SETUP
Setup
to select and press to return
ENTER RETURN
QUICK SETUP
Select the menu language.
English
Deutsch
Español
Svenska
Français
Italiano
Português
Nederlands
VHS
DVD
Select the maximum sampling frequency
of the .
Before you proceed please check which setting is supported
by your digital audio component (connection via OPTICAL).
PCM digital output
See page 18 of Operating Instructions.
Select your TV's aspect ratio.
The format of TV screens is either 4:3 (standard) or 16:9 (wide-
screen). Select the aspect ratio that matches the screen setting of
your TV set.
DVD may follow VCR Auto Setup.
Use the remote control's VHS/DVD function to select DVD.
Press SETUP to display the menu.
Use the navigator keys to select a menu language,
then press ENTER to confirm.
To continue with setting the defaults, press to select [ ]
and ENTER to confirm. You can later go to the menu to
run again.
!
Use the menu options to adapt the default settings below
to your appliance. Every menu item provides further information
on the options you have. 5
QUICK SETUP
QUICK SETUP
Setup
QUICK SETUP
Setup
!
!
See page 5 of Operating Instructions.
Yes
- 6 -
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Panasonic NV-VP31 Operating instructions

Panasonic
Brand
Panasonic
Model
NV-VP31
Type
Operating instructions
This manual is also suitable for

Panasonic NV-VP31 is a VCR/DVD set that includes functions for both recording and DVD playback. This device will allow you to connect your TV and watch channels that you select on the device by using the buttons or the remote control that comes with the set. You can set the device to automatically tune to available TV stations with the Auto Setup function. In addition to watching TV, the Panasonic NV-VP31 also supports recording TV programs, allowing you to watch them later.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers