Panasonic DLP Projectors(PTD7600/7500)
RS-232C Control Specifications
2003/03/27/2003
<CONTENTS>
1. Applicable models of Projectors ………………………………………… 1
2. Communication Format ……………………………………………………… 1
3. Command Format ……………………………………………………………… 2
4. Control by RS232C …………………………………………………………… 4
5. Commands
Control Command of R/C or key-pad …………………………………………… 5
Set-up Command of adjustment parameters …………………………………… 6
Status Monitoring Command ……………………………………………………… 10
1. Applicable Models
PTD7600U, PTD7500U
2. Communication Format
- Transfer Rate : 1200/2400/4800/9600/19200/38400/57600/
76800/102400/115200/153600/307200/
460800/921600 bps
- Parity Bit : Odd number / Even number / None
- Data Length : 8 bits
- Start, Stop Bit : 1 bit
- X, Y Parameter : None
- VPS SYSTEM : MASTER / SLAVE
* MASTER : Response to ID ALL command.
SLAVE : No response to ID ALL command
* Note for the system which use more than one unit
A. Set communication format same to the all, only one unit should be set as VPS SYSTEM
MASTER , the others should be set to VPS SYSTEM SLAVE.
B. Each projectors set to SLAVE should have own different ID.
C. When the projector’s main power is turned off, no output comes through RS-232C.
Turn on power of every projector to communicate Master and Slaves’ projectors.
* The Transfer Rate, Parity and VPS System can be set with RS-232C Setting in
Option menu.
* Projectors’ ID can be set with Option menu in each unit.
* Please use strait cable for communication between PC and Projectors.
3. Command Format
[STX] AD**:C1 C2 C3:p1p2p3…pn (Voluntary length) [ETX]
(note) Parameters after ':' to be added upon necessity.
First 5 alpha numeric after STX("AD**:"(** is ID#))designates ID,
followed by 3 alpha numeric codes which act Commands,
then followed by “ETX” for indicates end.
ID# is ruled as follows
ADnn(ASCII 4 characters)
nn : 01- 64 Individual addresses
0A－0Z Group ID
ZZ Address to all equipments (ID AL)
4. Control by RS-232C
CPU in the projector would act immediately after it receives RS232C Command codes.
When the projector is in the stand-by mode, it only accepts “Power-ON” command.
(In the practical operation at Stand-by Mode, it would receive the command codes
and eco backs as the normal communication ended.)
Key-Repeat function does not work in the RS232C control.
In case multiple commands are being sent, first receive the eco-back
of the previous command and then the next command can be transformed.
When the invalid command is received, the response from the projector would be
[STX] ER401 [ETX]
（Ref）[STX] ER N1 N2 N3 [ETX]
N1 shows product category, N1 = 4 means TV Display category.
N2 N3 shows error types, N2 N3 = 01 means
“Invalid Command”(Machine did not react for it).
5. Command List
Control Command of R/C or key-pad
Item Command:Parameter Function Call Back Remarks
POWER PON POWER ON PON
POF POWER OFF POF
FREEZE OFZ:0 FREEZE OFZ
OFZ:1 0=OFF 1=ON OFZ
MENU OMN MENU OMN
ENTER OEN ENTER OEN
CURSOR OCU Up OCU
OCD Down OCD
OCL Left OCL
OCR Right OCR
STANDARD OST STANDARD OST
AUTO SETUP OAS AUTO SETUP OAS
SHUTTER OSH:0 SHUTTER OSH:0
OSH:1 0=OFF 1=ON OSH:1
INPUT SELECT IIS:RG1 RGB-1 IIS:RG1
IIS:RG2 RGB-2 IIS:RG2
IIS:VID VIDEO IIS:VID
IIS:SVD S-VIDEO IIS:SVD
IIS:AUX AUX IIS:AUX
IIS:AUX,AW1 AUX LINE(Only AW) IIS:AUX,AW1
IIS:AUX,AW2 AUX Y/C (Only AW) IIS:AUX,AW2
FUNCTION1 FC1 Function1 FC1
TEST OTS:p1p2 Change Test Pattern OTS:p1p2
00=OFF 01=White 02=Black 03=Checker
04=Checker2 05=1%W-Window
06=1%B-Window 07=Cross Hatch
ON SCREEN OOS:0 OSD Change OOS:0
OOS:1 0= OSD OFF 1=OSD ON OOS:1
NEXT ONX NEXT キー ONX
NUMBER KEY ONK:0 NUMBER KEY 0 ONK:0
ONK:1 NUMBER KEY 1 ONK:1
ONK:2 NUMBER KEY 2 ONK:2
ONK:3 NUMBER KEY 3 ONK:3
ONK:4 NUMBER KEY 4 ONK:4
ONK:5 NUMBER KEY 5 ONK:5
ONK:6 NUMBER KEY 6 ONK:6
ONK:7 NUMBER KEY 7 ONK:7
ONK:8 NUMBER KEY 8 ONK:8
ONK:9 NUMBER KEY 9 ONK:9
SYSTEM SEL OSL SYSTEM SELECTER KEY OSL
Adjustment Mode
Item Command:Paramet
er
Function Call Back Remarks
PICTURE MODE VPM:NAT NATURAL VPM:NAT
VPM:STD STANDARD VPM:STD
VPM:DYN DYNAMIC VPM:DYN
VPM:CIN CINEMA VPM:CIN
VPM:GRA GRAPHIC VPM:GRA
COLOR VCO:p1p2p3 COLOR Value Adjust VCO:p1p2p3 From0 To 100 ＊1
TINT VTN:p1p2p3 TINT Value Adjust VTN:p1p2p3 From0 To 60 ＊1
COLOR TEMP. OTE:0 LOW OTE:0
OTE:1 MIDDLE OTE:1
OTE:2 HIGH OTE:2
OTE:3 DYNAMIC OTE:3
OTE:4 USER OTE:4
OTE:5 STANDARD OTE:5
OTE:6 NATURAL OTE:6
OTE:7 CINEMA OTE:7
OTE:8 GRAPHIC OTE:8
WHITE BALANCE
LOW(R)
VOR:p1p2p3 WHITE BALANCE LOW(R) VOR:p1p2p3 From0 To 255 ＊1
WHITE BALANCE
LOW(G)
VOG:p1p2p3 WHITE BALANCE LOW(G) VOG:p1p2p3 From0 To 255 ＊1
WHITE BALANCE
LOW(B)
VOB:p1p2p3 WHITE BALANCE LOW(B) VOB:p1p2p3 From0 To 255 ＊1
WHITE BALANCE
HIGH(R)
VHR:p1p2p3 WHITE BALANCE HIGH(R) VHR:p1p2p3 From0 To 255 ＊1
WHITE BALANCE
HIGH(G)
VHG:p1p2p3 WHITE BALANCE HIGH(G) VHG:p1p2p3 From0 To 255 ＊1
WHITE BALANCE
HIGH(B)
VHB:p1p2p3 WHITE BALANCE HIGH(B) VHB:p1p2p3 From0 To 255 ＊1
GAMMA VGA:2.2 GAMMA 2.2 VGA:2.2
VGA:2.5 GAMMA 2.5 VGA:2.5
VGA:US1 GAMMA USER1 VGA:US1
VGA:US2 GAMMA USER2 VGA:US2
VGA:NAT GAMMA NATURAL VGA:NAT
VGA:ST1 GAMMA STANDARD1 VGA:ST1
VGA:ST2 GAMMA STANDARD2 VGA:ST2
VGA:CIN GAMMA CINEMA VGA:CIN
VGA:GR1 GAMMA GRAPHIC1 VGA:GR1
VGA:GR2 GAMMA GRAPHIC2 VGA:GR2
CONTRAST VCN:p1p2p3 CONTARST Value Adjust VCN:p1p2p3 From0 To 63 ＊1
BRIGHTNESS VBR:p1p2p3 BRIGHTNESS Value Adjust VBR:p1p2p3 From0 To 63 ＊1
SHARPNESS VSR:p1p2p3 SHARPNESS Value Adjust VSR:p1p2p3 <SD>From0 To 15,
<HD,RGB>From0 To 7 ＊1
NOISE REDUCTION VNS:0 OFF VNS:0
VNS:1 1 VNS:1
VNS:2 2 VNS:2
VNS:3 3 VNS:3
AI CONTROL OAI:0 OFF OAI:0
OAI:1 ON OAI:1
Pull Down Mode OPD:0 AUTO OPD:0
OPD:1 OFF OPD:1
OPD:2 2:2ON（Fix） OPD:2
COLOR MATCHING VCM:0 OFF VCM:0
VCM:1 USER VCM:1
SET COLOR
MATCHING
VMR:p1p2p3p4,
p5p6p7p8,
p9p10p11p12
R VMR:p1p2p3p4,
p5p6p7p8,
p9p10p11p12
From 0 To 4095 ＊2
VMG:p1p2p3p4,
p5p6p7p8,
p9p10p11p12
G VMG:p1p2p3p4,
p5p6p7p8,
p9p10p11p12
From 0 To 4095 ＊2
VMB:p1p2p3p4,
p5p6p7p8,
p9p10p11p12
B VMB:p1p2p3p4,
p5p6p7p8,
p9p10p11p12
From 0 To 4095 ＊2
TV-SYSTEM/ [VIDEO] [VIDEO]
SIGNAL MODE VSG:AT1 AUTO1 VSG:AT1
VSG:AT2 AUTO2 VSG:AT2
VSG:NTS NTSC VSG:NTS
VSG:N44 NTSC4.43 VSG:N44
VSG:PAL PAL VSG:PAL
VSG:PAN N-PAL VSG:PAN
VSG:PAM M-PAL VSG:PAM
VSG:SEC SECAM VSG:SEC
VSG:P60 PAL60 VSG:P60
VSG:BW5 B/W50Hz VSG:BW5
VSG:BW6 B/W60Hz VSG:BW6
SDI Input VSD:0 AUTO VSD:0
VSD:1 480i VSD:1
VSD:2 480p VSD:2
VSD:3 576i VSD:3
VSD:4 1080/60i VSD:4
VSD:5 1035/60i VSD:5
VSD:6 720/60p VSD:6
VSD:7 1080/24p VSD:7
VSD:8 1080/50i VSD:8
VSD:9 1080/30p VSD:9
VSD:10 1080/25p VSD:10
VSD:11 1080/24sF VSD:11
SHIFT H VTH:p1p2p3p4 H-SHIFT Value VTH:p1p2p3p4 Range Depends On
Resolution＊2
SHIFT V VTV:p1p2p3p4 V-SHIFT Value VTV:p1p2p3p4 Range Depends On
Resolution＊2
SIZE <VIDEO NTSC>
VSE:0 VID AUTO VSE:0
VSE:1 4:3 VSE:1
VSE:2 16:9 VSE:2
VSE:3 S4:3 VSE:3
VSE:4 ZOOM VSE:4
VSE:5 THROUGH VSE:5
VSE:6 HV FIT VSE:6
<Besides VIDEO
NTSC>
VSE:0 DEFAULT VSE:0
VSE:1 4:3 VSE:1
VSE:2 16:9 VSE:2
VSE:3 S4:3 VSE:3
VSE:4 ZOOM VSE:4
VSE:5 THROUGH VSE:5
VSE:6 HV FIT VSE:6
<SVIDEO NTSC>
VSE:0 VID AUTO(Priority) VSE:0
VSE:1 4:3 VSE:1
VSE:2 16:9 VSE:2
VSE:3 S4:3 VSE:3
VSE:4 ZOOM VSE:4
VSE:5 THROUGH VSE:5
VSE:6 S1 AUTO VSE:6
VSE:7 VID AUTO VSE:7
VSE:8 HV FIT VSE:8
<Besides SVIDEO
NTSC>
VSE:0 DEFAULT VSE:0
VSE:1 4:3 VSE:1
VSE:2 16:9 VSE:2
VSE:3 S4:3 VSE:3
VSE:4 ZOOM VSE:4
VSE:5 THROUGH VSE:5
VSE:6 HV FIT VSE:8
<RGB>
VSE:0 DEFAULT VSE:0
VSE:1 4:3 VSE:1
VSE:2 16:9 VSE:2
VSE:3 S4:3 VSE:3
VSE:4 ZOOM VSE:4
VSE:5 THROUGH VSE:5
VSE:6 HV FIT VSE:6
<SD>
VSE:0 DEFAULT VSE:0
VSE:1 4:3 VSE:1
VSE:2 16:9 VSE:2
VSE:3 S4:3 VSE:3
VSE:4 ZOOM VSE:4
VSE:5 THROUGH VSE:5
VSE:6 HV FIT VSE:6
<HD>
VSE:0 DEFAULT VSE:0
VSE:1 4:3 VSE:1
VSE:2 16:9 VSE:2
VSE:3 S4:3 VSE:3
VSE:4 ZOOM VSE:4
VSE:5 THROUGH VSE:5
VSE:6 HV FIT VSE:6
ZOOM（H) OZH:p1p2p3 Horizontal Zoom Value OZH:p1p2p3 ＊1
ZOOM（V) OZV:p1p2p3 Vertical Zoom Value OZV:p1p2p3 ＊1
ZOOM（HV) OZO:p1p2p3 H&V Zoom Value OZO:p1p2p3 ＊1
ZOOM OZS:0 OFF OZS:0
OZS:1 ON OZS:1
Blanking(UPPER) DBU:p1p2p3 BLANKING Value(Upper) DBU:p1p2p3 From0 To 511 ＊1
Blanking(LOWER) DBB:p1p2p3 BLANKING Value(Lower) DBB:p1p2p3 From0 To 511 ＊1
Blanking(LEFT) DBL:p1p2p3 BLANKING Value（Lest） DBL:p1p2p3 From0 To 511 ＊1
Blanking(RIGHT) DBR:p1p2p3 BLANKING Value（Right） DBR:p1p2p3 From0 To 511 ＊1
CLOCK PHASE VCP:p1p2p3 CLOCK PAHSE Value VCP:p1p2p3 From0 To 31 ＊1
INPUT RESOLUTION Input Resolution
total dots VTD:p1p2p3p4 Total Dots VTD:p1p2p3p4 From 330 To 4094 ＊2
display dots VDD:p1p2p3p4 Displayed Dots VDD:p1p2p3p4 From 300 To 2046 ＊2
total lines VTL:p1p2p3p4 Total Lines VTL:p1p2p3p4 From 211 To 2047 ＊2
display lines VDL:p1p2p3p4 Displayed Lines VDL:p1p2p3p4 From 200 To 1200 ＊2
Clamp Position Clamp Position
Position VLT:p1p2p3 Position VLT:p1p2p3 From 1 To 255 ＊1
KEYSTONE OKS:p1p2p3 Keystone Adjust OKS:p1p2p3 From 0 To 127 ＊1
LINEARITY VLI:p1p2p3 LINEARITY Adjust VLI:p1p2p3 ＊1
EDGE BLENDING
(UPPER)
VEU:p1p2p3 EDGE BLENDING (UPPER) VEU:p1p2p3 From 0 To 255 ＊1
EDGE BLENDING VEB:p1p2p3 EDGE BLENDING (LOWER) VEB:p1p2p3 From 0 To 255 ＊1
(LOWER)
EDGE BLENDING
(LEFT)
VEL:p1p2p3 EDGE BLENDING (LEFT) VEL:p1p2p3 From 0 To 255 ＊1
EDGE BLENDING
(RIGHT)
VER:p1p2p3 EDGE BLENDING (RIGHT) VER:p1p2p3 From 0 To 255 ＊1
EDGE BLENDING VGU:0 OFF VGU:0
(UPPER)on/off VGU:1 ON VGU:1
EDGE BLENDING VGB:0 OFF VGB:0
(LOWER)on/off VGB:1 ON VGB:1
EDGE BLENDING VGL:0 OFF VGL:0
(LEFT)on/off VGL:1 ON VGL:1
EDGE BLENDING VGR:0 OFF VGR:0
(RIGHT)on/off VGR:1 ON VGR:1
EDGE BLENDING VGM:0 OFF VGM:0
(marker)on/off VGM:1 ON VGM:1
BRIGHT ADJUST
INSIDE
VJI:p1p2p3 BRIGHT ADJUST(INSIDE) VJI:p1p2p3 From 0 To 255 ＊1
BRIGHT ADJUST
OUTSIDE
VJO:p1p2p3 BRIGHT ADJUST(OUTSIDE) VJO:p1p2p3 From 0 To 255 ＊1
BRIGHT ADJUST
UPPER
VJU:p1p2p3 BRIGHT ADJUST(UPPER) VJU:p1p2p3 From 0 To 255 ＊1
BRIGHT ADJUST
LOWER
VJB:p1p2p3 BRIGHT ADJUST(LOWER) VJB:p1p2p3 From 0 To 255 ＊1
BRIGHT ADJUST
LEFT
VJL:p1p2p3 BRIGHT ADJUST(LEFT) VJL:p1p2p3 From 0 To 255 ＊1
BRIGHT ADJUST
RIGHT
VJR:p1p2p3 BRIGHT ADJUST(RIGHT) VJR:p1p2p3 From 0 To 255 ＊1
LANGUAGE OLG:ENG Language（English） OLG:ENG
OLG:DEU （German） OLG:DEU
OLG:FRA （French） OLG:FRA
OLG:ESP （Spanish） OLG:ESP
OLG:ITL （Italian） OLG:ITL
OLG:JPN （Japanese） OLG:JPN
OLG:CHI （Chinese） OLG:CHI
ID SET RIS:p1p2 ID-Setting Of Unit RIS:p1p2
INSTALLATION OIL:0 Front/Floor OIL:0
OIL:1 Rear/Floor OIL:1
OIL:2 Front/Ceiling OIL:2
OIL:3 Rear/Ceiling OIL:3
LAMP SELECT LPM:0 Lamp Select LPM:0 ＊3
LPM:1 0=DUAL 1=SINGLE LPM:1
LPM:2 2=LAMP1 3=LAMP2 LPM:2
LPM:3 LPM:3
LAMP POWER OLP:0 LAMP POWER Setting OLP:0
OLP:1 0=HIGH 1=LOW OLP:1
Lamp Cooling
Time
OLC:0 normal OLC:0
OLC:1 speedy OLC:1
VPS SYSTEM RVS:0 SLAVE RVS:0
RVS:1 MASTER RVS:1
GROUP SET ADa1a2;RGS:g1g2 GROUPING ADa1a2;RGS
GROUP CANCEL ADa1a2;RGC Cancel GROUPING ADa1a2;RGC
GROUP LEADER SET ADg1g2;RGR:a1a2 Group Leader Select ADa1a2;RGR
GROUP LEADER
CANCEL
ADg1g2;RLC Cancel Group Leader ADa1a2:RLC
RGB2 SELECT ORI:2IN RGB2 INPUT ORI:2IN
ORI:2OU RGB1 OUTPUT ORI:2OU
VIDEO SELECT VM1:0 LINE or Y/C VM1:0 MD95VM2(AW) Setting
VM1:1 YCbCr VM1:1
VIDEO SYSTEM VY1:AT1 AUTO1 VY1:AT1
(VIDEO) VY1:AT2 AUTO2 VY1:AT2
VIDEO SYSTEM VY2:AT1 AUTO1 VY2:AT1
(S-VIDEO) VY2:AT2 AUTO2 VY2:AT2
VIDEO SYSTEM VY3:AT1 AUTO1 VY3:AT1
(MD95VM2 LINE) VY3:AT2 AUTO2 VY3:AT2
VIDEO SYSTEM VY4:AT1 AUTO1 VY4:AT1
(MD95VM2 Y/C) VY4:AT2 AUTO2 VY4:AT2
FAN CONTROL OFM:0 FAN CONTROL OFM:0
OFM:1 0:NORMAL 1:HIGH OFM:1
P in P OPP:0 P in P OPP:0
OPP:1 0=OFF 1=ON OPP:1
P in P P in P
main
position(V)
MPV:p1p2p3p4 V-Position MPV:p1p2p3p4 Depends On Resolution
main
position(H)
MPH:p1p2p3p4 H-Position MPH:p1p2p3p4 Depends On Resolution
main size(HV) MSL:0 OFF MSL:0
MSL:1 ON MSL:1
main size(V) MSV:p1p2p3 Main Size(V) Setting MSV:p1p2p3 ＊1
main size(H) MSH:p1p2p3 Main Size(H) Setting MSH:p1p2p3 ＊1
main size(HV) MSZ:p1p2p3 Main Size(HV) Setting MSZ:p1p2p3 ＊1
Sub Input SIS:RG1 RGB1 SIS:RG1
SIS:RG2 RGB2 SIS:RG2
SIS:VID VIDEO SIS:VID
SIS:SVD S-VIDEO SIS:SVD
SIS:AUX AUX SIS:AUX
sub
position(V)
SPV:p1p2p3p4 Position SPV:p1p2p3p4 ＊2
sub
position(H)
SPH:p1p2p3p4 Position SPH:p1p2p3p4 ＊2
sub size(HV) SSL:0 OFF SSL:0
SSL:1 ON SSL:1
sub size(V) SSV:p1p2p3 Sub Size(V) Setting SSV:p1p2p3 ＊1
sub size(H) SSH:p1p2p3 Sub Size(H) Setting SSH:p1p2p3 ＊1
sub size(HV) SSZ:p1p2p3 Sub Size(HV) Setting SSZ:p1p2p3 ＊1
frame lock PFL:0 main PFL:0
PFL:1 sub PFL:1
type PTP:0 main on sub PTP:0
PTP:1 sub on main PTP:1
linearity PLI:0 main PLI:0
PLI:1 sub PLI:1
FUNCTION1 OFC:0 Change Function1 OFC:0
OFC:1 0= PinP 1= LAMP POWER OFC:1
OFC:2 2= SIZE OFC:2
SUB MEMORY OCS:p1p2 SUB MEMORY Change OCS:p1p2
ENTRY SIGNAL OEM Entry Current Signal OEM
DELETE SIGNAL ODM:p1p2 Remove Current Sugnal ODM:p1p2 p1p2 :
A1,A2,…,A8,B1,B2,…,L7,L8
ENTRY SUB MEMORY OES Entry Current Signal Into
Sub-Memory
OES
DELETE SUB
MEMORY
ODS:p1p2-p3p4 Remove Current Signal From
Sub-Memory
ODS:p1p2-p3p4
SET DATE TSD:y1y2y3y4
m1m2d1d2w
Set Date TSD:y1y2y3y4
m1m2d1d2w
y1y2y3y4m1m2d1d2 ＋ Date of
Week
Mon=1,Tue=2,…,Sun=7 ＊4
SET TIME TST:h1h2m1m2s1s2 Set Time TST:h1h2m1m2s1s
2
＊4
※1: Regarding p1p2p3, +1,+01,+001,1,01,001 are All Accepted
※2: Regarding p1p2p3p4, +1,+01,+001,+0001,1,01,001,0001 are All Accepted
※3: 「SINGLE」Would Select the Shorter Runtime One Out Of LAMP1/LAMP2
※4: Date/Time Should be set on GMT(World Standard Time)
Status Asking Comman
Item Command:Par
ameter
Function Call Back Meaning Remarks
POWER CONDITION QPW Main Power Status 000 OFF
001 ON
FREEZE QFZ Freeze Function Status 0 OFF
1 ON
SHUTTER QSH Mechanical Shutter Status 0 OFF
1 ON
AUTO SETUP QAS Auto Setup Status 0 In Process
1 In Stop
INPUT SIGNAL QIN Input Signal Status RG1 RGB1
RG2 RGB2
VID VIDEO
SVD S-VIDEO
AUX AUX
QIN:AW AUX,AW1 AUX LINE MD95VM2
QIN:AW AUX,AW2 AUX Y/C MD95VM2
TEST QTS Test Pattern Status p1p2
ON SCREEN QOS ON SCREEN Status 0 off
1 on
PICTURE MODE QPM PICTURE MODE Status] NAT NATURAL
STD STANDARD
DYN DYNAMIC
CIN CINEMA
GRA GRAPHIC
COLOR QVC COLOR Adjust Value Check p1p2p3
TINT QVT TINT Adjust Value Check p1p2p3
COLOR TEMP. QTE COLOR TEMP Status Check 0 LOW
1 MIDDLE
2 HIGH
3 DYNAMIC
4 USER
5 STANDARD
6 NATURAL
7 CINEMA
8 GRAPHIC
WHITE BALANCE LOW(R) QOR WHITE BALANCE LOW(R) Value p1p2p3
WHITE BALANCE LOW(G) QOG WHITE BALANCE LOW(G) Value p1p2p3
WHITE BALANCE LOW(B) QOB WHITE BALANCE LOW(B) Value p1p2p3
WHITE BALANCE HI(R) QHR WHITE BALANCE HI(R) Value p1p2p3
WHITE BALANCE HI(G) QHG WHITE BALANCE HI(G) Value p1p2p3
WHITE BALANCE HI(G) QHB WHITE BALANCE HI(B) Value p1p2p3
GAMMA QGA GAMMA Value Check 2.2 GAMMA 2.2
2.5 GAMMA 2.5
US1 GAMMA USER1
US2 GAMMA USER2
NAT GAMMA NATURAL
ST1 GAMMA STANDARD1
ST2 GAMMA STANDARD2
CIN GAMMA CINEMA
GR1 GAMMA 値 GRAPHIC1
GR2 GAMMA 値 GRAPHIC2
CONTRAST QVR CONTARST Adjust Value Checking p1p2p3
BRIGHTNESS QVB BRIGHTNES Adjust Value p1p2p3
SHARPNESS QVS SHARPNESS Adjust Value p1p2p3
NOISE REDUCTION QNS NR Adjust Value 0 OFF
1 1
2 2
3 3
AI CONTROL QAI AI CONTROL Status Check 0 OFF
1 ON
Pull Down Mode QPD Pull Down Mode Check 0 AUTO
1 OFF
2 2:2ON(Fix)
COLOR MATCHING QMC Color Matching Status 0 OFF
1 USER
GET COLOR MATCHING QMR R‐Value Check p1p2p3p4,p5p6p7p8
,p9p10p11p12
QMG G‐Value Check p1p2p3p4,p5p6p7p8
,p9p10p11p12
QMB B‐Value Check p1p2p3p4,p5p6p7p8
,p9p10p11p12
TV-SYSTEM/ QSG TV-SYSTEM/SIGNAL MODE Check [VIDEO]
SIGNAL MODE AT1 AUTO1
AT2 AUTO2
NTS NTSC
N44 NTSC443
PAL PAL
PAN N-PAL
PAM M-PAL
SEC SECAM
P60 PAL60
BW5 B/W50
BW6 B/W60
SDI Input QSD AUTO 0 AUTO
480i 1 480i
480p 2 480p
576i 3 576i
1080/60i 4 1080/60i
1035/60i 5 1035/60i
720/60p 6 720/60p
1080/24p 7 1080/24p
1080/50i 8 1080/50i
1080/30p 9 1080/30p
1080/25p 10 1080/25p
1080/24sF 11 1080/24sF
SHIFT H QTH H-Shift Status p1p2p3p4
SHIFT V QTV V-Shift Status p1p2p3p4
SIZE QSE SIZE <VIDEO NTSC>
0 VID AUTO
1 4:3
2 16:9
3 S4:3
4 ZOOM
5 THROUGH
6 HV FIT
<VIDEO NTSC 以外>
0 DEFAULT
1 4:3
2 16:9
3 S4:3
4 ZOOM
5 THROUGH
6 HV FIT
<SVIDEO NTSC>
0 VID AUTO
(Priority)
1 4:3
2 16:9
3 S4:3
4 ZOOM
5 THROUGH
6 S1 AUTO
7 VID AUTO
8 HV FIT
<SVIDEO NTSC 以外>
0 DEFAULT
1 4:3
2 16:9
3 S4:3
4 ZOOM
5 THROUGH
6 HV FIT
<RGB>
0 DEFAULT
1 4:3
2 16:9
3 S4:3
4 ZOOM
5 THROUGH
6 HV FIT
<SD>
0 DEFAULT
1 4:3
2 16:9
3 S4:3
4 ZOOM
5 THROUGH
6 HV FIT
<HD>
0 DEFAULT
1 4:3
3 S4:3
4 ZOOM
5 THROUGH
6 HV FIT
ZOOM（H） QZH H-Zoom Value Check p1p2p3
ZOOM（V） QZV V-Zoom Value Check p1p2p3
ZOOM（H/V） QZO HV Zoom Value Check p1p2p3
ZOOM QZS ZOOM HV Status Check 0 OFF
1 ON
BLANKING (UPPER) QLU BLANKING(Upper) Check p1p2p3
BLANKING (LOWER) QLB BLANKING(Lower) Check p1p2p3
BLANKING (LEFT) QLL BLANKING(L) Check p1p2p3
BLANKING (RIGHT) QLR BLANKING(R) Check p1p2p3
CLOCK PHASE QCP CLOCK PHASE Value Check p1p2p3
INPUT RESOLUTION Input Resolution Check
total dots QTD Total dots p1p2p3p4
display dots QDD Display dots p1p2p3p4
total lines QTL Total lines p1p2p3p4
display lines QDL Display lines p1p2p3p4
Clamp Position Clamp Position Check
Position QLT Position p1p2p3
KEYSTONE QKS Digital Keystone Adjustment Value
Check
p1p2p3
LINEARITY QLI Keystone Linearity Adjustment Value
Check
p1p2p3
EDGE BLENDING (UPPER) QEU Edge Blending(Upper) Value Check p1p2p3
EDGE BLENDING (LOWER) QEB Edge Blending(Lower) Value Check p1p2p3
EDGE BLENDING (LEFT) QEL Edge Blending(Left) Value Check p1p2p3
EDGE BLENDING (RIGHT) QER Edge Blending(Right) Value Check p1p2p3
EDGE BLENDING QGU Edge Blending(Upper) on or off Check 0 OFF
(UPPER)on/off 1 ON
EDGE BLENDING QGB Edge Blending(Lower) on or off Check 0 OFF
(LOWER)on/off 1 ON
EDGE BLENDING QGL Edge Blending(Left) on or off Check 0 OFF
(LEFT)on/off 1 ON
EDGE BLENDING QGR Edge Blending(Right) on or off Check 0 OFF
(RIGHT)on/off 1 ON
EDGE BLENDING QGM Edge Blending(Marking) on or off 0 OFF
(marker)on/off Check 1 ON
LANGUAGE QLG On Screen Language Check ENG English
DEU German
FRA French
ESP Spanish
ITL Italian
JPN Japanese
CHI Chinese
INSTALLATION QSP Installation Setting Check 0 Front/Floor
1 Rear/Floor
2 Front/Ceiling
3 Rear/Ceiling
SET RUNTIME QST Set Run Time CHeck p1p2p3p4p5 00000h～99999h
LAMP ON TIME Q$L:p1 Lamp Run Time Check p1p2p3p4 0000h～9999h
(LAMP TIMER) (p1 = 1 or 2) 1=LAMP1 2=LAMP2
LAMP SELECT QSL Lamp Operation Mode Check 0 DUAL
1 SINGLE
2 LAMP1
3 LAMP2
LAMP POWER QLP LAMP POWER Mode Check 0 HIGH
1 LOW
Lamp Cooling Time QLC Lamp Cooling Time Check 0 normal
1 short
VPS SYSTEM QVY VPS SYSTEM Check 0 SLAVE
1 MASTER
GROUP GET ADa1a2;QRG GROUP Get ADa1a2;RGSg1g2
MASTER GET ADg1g2;QRL Group Master Get ADa1a2;RGLa1a2
RGB2 SELECT QRI RGB2 SELECT Status Check 2IN RGB2 IN
2OU RGB1 OUT
VIDEO SELECT QM1 MD95VM2 Board Setting Check 0 Video or Y/C When ETMD95VM2
1 YCbCr Is Installed
VIDEO SYSTEM QY1 Check the Video System Setting AT1 AUTO1
(VIDEO) (VIDEO) AT2 AUTO2
VIDEO SYSTEM QY2 Check the Video System Setting AT1 AUTO1
(S-VIDEO) (S-VIDEO) AT2 AUTO2
VIDEO SYSTEM QY3 Check the Video System Setting AT1 AUTO1
(MD95VM2 LINE) (through ETMD95VM2 Video) AT2 AUTO2
VIDEO SYSTEM QY4 Check the Video System Setting AT1 AUTO1
(MD95VM2 Y/C) (through ETMD95VM2 Y/C) AT2 AUTO2
INPUT BOARD QIB Check the type of Input Board p1p2p3p4……… MD95VM2
(Voluntary length)
MD95SD1
MD95SD2
MD95SD3
MD95RGB
MD75NT
MD75DV
NONE No board
UNKNOWN Unknown board
NOT SUPPORT Unsupported board
TEMP CHECK QTM:p1 Check the status of Temperature p1p2p3p4/p5p6p7p8 p1=0 at air intake
Sensor （Celsius/ p1=1 at exhaust
Fahrenheit） p1=2 at DMD chip
FAN CONTROL QFM FAN CONTROL Check 0 NORMAL
1 HIGH
P in P QPP P in P ON/OFF Check 0 OFF
1 ON
P in P P in P Setting Check
main input signal QIM Main Input Signal Check RG1 RGB1
RG2 RGB2
VID VIDEO
SVD S-VIDEO
AUX AUX
main position QPA Main Picture Position Check Vp1p2p3p4,
Hp5p6p7p8
Depends on
Resolution , Can be
negative number
main size QSM Main Picture Size Check (ON or OF),
Vp1p2p3,
Hp4p5p6,
HVp7p8p9
(ON or OF) means
HV gearing ON/OFF
sub input signal QIS Sub Picture Signal Check RG1 RGB1
RG2 RGB2
VID VIDEO
SVD S-VIDEO
AUX AUX
sub position QPS Sub Picture Position Check Vp1p2p3p4,
Hp5p6p7p8
Depends on
Resolution , Can be
negative number
sub size QSS Sub Picture Size Check (ON or OF),
Vp1p2p3,
Hp4p5p6,
HVp7p8p9
(ON or OF) means
HV gearing ON/OFF
frame lock QPF Flame Lock Check 0 main
1 sub
type QPT Type Check 0 main
1 sub
linearity QPL Linearity Check 0 main
1 sub
FUNCTION1 QFC FUNCTION1 Setting Check 0 P in P
1 LAMP POWER
2 SIZE
SUB MEMORY QSB SUB MEMORY Status Check p1p2
GET DATE QGD Check the Day y1y2y3y4m1m2
d1d2w
Yyyymmdd (day of
the week)
Mon=1,Tur=2,
…,Sun=7
GET TIME QGT Check the Time h1h2m1m2s1s2 hhmmss GMT
Lamp Cooling Time QLC Check the Lamp Cooling Time Setting 0 normal
1 short
/
