15
TABLE OF CONTENTS GB
INSTALLATION
PAGE
16
ELECTRICAL CONNECTION
PAGE
18
BEFORE USING THE APPLIANCES
PAGE
19
PROTECTING THE ENVIRONMENT
PAGE
19
PRECAUTIONS AND
GENERAL RECOMMENDATIONS
PAGE
19
ENERGY SAVING TIPS
PAGE
20
OVEN ACCESSORIES
PAGE
21
COOKTOP ACCESSORIES
PAGE
21
COOKING CHARTS
PAGE
22
CLEANING THE OVEN AND ACCESSORIES
PAGE
23
CARE AND MAINTENANCE OF
CONVENTIONAL ELECTRIC COOKTOPS
PAGE
25
CARE AND MAINTENANCE OF GLASS-
CERAMIC COOKTOPS
PAGE
25
TROUBLESHOOTING GUIDE
PAGE
25
AFTER SALES SERVICE
PAGE
26
DECLARATION OF CONFORMITY CE
PAGE
26
16
Technical information for the installer
OVEN
•
After removing the oven from its packaging, before
making the connections place it on the polystyrene
foam base to protect it from damage.
•
Do not attempt to lift the oven by the handle.
Lift at the sides as shown in the figure (see arrow).
•
Check that the appliance has not been damaged in
transit.
•
Oven dimensions and kitchen unit dimensions are
shown in the opposite figure.
•
Kitchen units in contact with the oven must be heat
resistant (80° C).
•
If plastic laminates or cement are not sufficiently
heat-resistant, warping, bubbling or detachment of
the finish may result.
•
For correct ventilation, follow the ventilation
opening directions shown in the figure (at least
500 x 80 mm). Also provide for at least 5 mm
clearance between the top of the oven and the
lower edge of the worktop. This space must not
be obstructed by cross rails or other structural
elements.
•
During oven installation, care must be taken to
ensure that the sides are not touching the front
edges of the housing or adjacent drawers and
doors (see picture).
•
Carry out the electrical connections between
cooktop and oven (see chapter “Electrical
connection”).
•
Secure the oven to the kitchen unit with screws (
A
)
as shown.
INSTALLATION
No contacts
17
Cooktop
• The cooktop must be set into a worktop
between 20 mm and 50 mm thick.
There must be nothing between the cooktop
and the oven (cross rails, brackets, etc.).
• If the cooktop is to be installed next to a
column unit, leave a distance of at least 100mm
from the edge of the cooktop to the side of the
column unit.
•
Cut an opening in the worktop of the dimensions
shown in the Product Description Sheet supplied
separately.
•
If not already present, fit the supplied seal to the
cooktop flange after cleaning the contact area as
shown in the figure.
Cooktop with electric hotplates
• If the worktop is made of wood, fit the supplied
clips.
1.
Position the 4 spring clips (
B
) and fit them in their
locations on the underside of the cooktop.
2.
Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc.,
the cooktop must
be secured with brackets (
C
) code 4819 310
18528 (to be requested from After Sales Service).
1.
Position the brackets over the holes and secure
them with the supplied screws.
2.
Fit the cooktop into the worktop.
Glass-ceramic cooktop
N.B.:
Remove the protective film before installing the
cooktop.
• If the worktop is made of wood,
use the supplied
spring clips and screws.
1.
Position the 4 clips (
D
) as shown and at the
specified dimensions.
2.
Secure the clips using screws (
E
).
3.
Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc.
, the cooktop must
be secured with brackets (
F
) code 4819 404 78697
(to be requested from After Sales Service).
1.
Fit the cooktop into the worktop.
2.
Position the 4 brackets (
F
) as shown in the figure,
in accordance with the thickness of the worktop.
3.
Fix the 4 screws (
G
) in holes (
H
).
INSTALLATION
18
Connecting the oven to the power supply
•
Make sure that the voltage shown on the rating
plate is the same as the power supply voltage in
your home. The rating plate is on the front edge of
the oven cavity (visible with oven door open).
•
Use a type H05RR-F power cord (minimum
length 800 mm).
• Warning: All the oven’s components operate at
230V.
Interconnecting cooktop and oven
•
Before connecting the oven to the power supply,
check that the cooktop is among the ones listed in
the cooktop/oven pairing product sheet.
Connect the 3 pole and 4 pole connectors to the
respective connectors on the oven.
•
The 3 pole connectors (
H
) is located at the rear
right hand side of the control panel, the 4 pole
connector (
J
) is located at the top of the oven in the
left hand corner (see figure).
•
Connect the yellow/green striped earth wire ( )
(
K
) from the cooktop to the screw located near the
3 pole connector.
WARNING: DO NOT CONNECT TO THE
POWER SUPPLY BEFORE YOU HAVE
FINISHED CONNECTING THE OVEN AND
COOKTOP.
•
Mount the oven in the kitchen unit.
Make sure the power cord is not trapped.
ELECTRICAL CONNECTION
Conductors X
number
Connection
2 +
~
H05 RR-F 3X4 mm²
3 +
~
H05 RR-F 4X2,5 mm²
• Make sure the appliances are installed
and connected to the electricity supply
by a qualified technician in accordance
with the manufacturer’s instructions and
in compliance with local regulations.
• The installer is responsible for the correct
electrical connection of the appliances
and the observance of the relative safety
regulations.
• The appliance must be connected to the
electricity supply by means of an all-pole
disconnect switch with minimum contact
gap of 3 mm.
• The appliances must be earthed by law.
• Do not use multiple plug adapters or
extension leads.
• After the appliances have been installed,
the electrical components must be
inaccessible.
19
•
To make the most of your new appliances,
read the users instructions carefully and keep
them on hand for consultation in the future.
•
Remove the cardboard protections and the
protective plastic film.
•
Remove the accessories from the oven and
heat it 200° C for about an hour to eliminate
the smell of protective grease and insulating
materials. Keep the window open during this
procedure.
N.B: The cooling fan runs continuously at
two different speeds according to the
temperature value of the components when
the appliances are in use.
Full speed: for high temperature of the
components.
Half speed pulsing: for low temperature of
the components.
The pulsing speed has to be considered a
normal appliance condition at half speed.
The fan may continue to run for the time
necessary to ensure sufficient cooling of the
components and adjacent kitchen units after
the appliance has been switched off.
1. Packing
•
The packaging material can be100%
recycled, as confirmed by the recycling
symbol ( ).
2. Products
•
The appliances are built from recyclable
materials. If you decide to scrap the appliances
please observe local waste disposal by-laws. Cut
off the power cords so that the appliances cannot
be connected to the mains.
.
•
Before any maintenance on the appliances
disconnect them from the electrical power
supply.
•
Keep children away from the appliances
when they are in use.
•
The appliances must be repaired or adjusted
only by a qualified technician.
•
Make sure that the electrical wires of other
electrical appliances near the cooktop or the
oven do not come into contact with hot parts
and do not become entrapped in the oven door.
•
The oven is equipped with air cooling system to
prevent excessive temperatures of the oven
front and furniture housing. Following cooking
times greater than one hour at temperatures of
200° C or more, it is recommended that
residual heat from the oven and housing be
removed by use of a cool down period. At
completion of cooking, leave the oven on, in
any cooking function but grill with the
“temperature knob” on “0” position, for about 15
minutes. The oven door must remain closed
during the cool down period.
Oven
•
Never stand or sit on the oven open door.
Never hand any weight at the handle of the
oven open door.
•
Use oven gloves to remove baking trays and
accessories when the oven is hot.
• Do not cover the bottom of the oven with
aluminium foil.
•
Do not place inflammable material in the oven -
risk of fire if the oven is inadvertently switched on.
•
During the cooking process, water evaporates
from food. All ovens require this steam and other
fumes to be vented from the oven cavity. For
reasons of safety and aesthetics, we have
determined that an opening at the bottom of the
door is the optimum solution. Consequently,
vapour may be seen to be coming from this area
on occasions (see picture). This is a normal
occurrence and the bottom trim can be cleaned
after removal of the door as described on
“Cleaning the oven and accessories”.
•
Heavy weights must not be placed on the open
door as this may result in damage to the cavity
and hinges. Max weight: 7 kg (15lbs)
.
BEFORE USING THE APPLIANCES
PROTECTING THE ENVIRONMENT
PRECAUTIONS AND GENERAL RECOMMENDATIONS
F
u
m
e
s
e
x
h
a
u
s
t
20
Conventional electric/glass-ceramic
cooktop
• Do not switch on the hotplates/cooking
zones when there is no pan in position.
•
The cooktop features different size hotplates/
cooking zones. Use pans whose base
diameter is the same as or slightly larger than
the diameter of the hotplate/cooking zone.
•
Use flat-bottomed pans. The use of pans with
concave or convex bottoms may damage the
cooktop.
•
Do not use the cooktop as a worksurface or a
support surface.
•
Do not leave the appliance unattended when
frying food - risk of fire.
Specific recommendations for glass-
ceramic cooktops
•
With the fast boiling function, only use
stainless steel pans with double layer
bottoms.
•
If the glass ceramic surface should break or
crack due to violent impact (falling objects,
etc.) do not use it and call After Sales Service
immediately.
•
Do not place food wrapped in aluminium foil,
plastic containers or cloths on the hot
cooking zones.
•
Do not drag pans across the glass-ceramic
surface - risk of scratches.
•
If your hob is provided with halogen lamps,
we recommend that you do not stare at them
during the operation.
•
Avoid spilling sugar and similar substances
on the cooktop. If necessary, clean the
cooktop carefully following the care and
maintenance instructions in this handbook.
•
Use pots and pans whose bottom diameter is
equal to that of the cooking zone or slightly
larger.
•
Only use flat-bottomed pots and pans.
•
If possible, keep the pot covered when cooking.
•
Cook vegetables, potatoes, etc. with little
water in order to cut down cooking time.
•
A pressure cooker allows you to save even
more energy and time.
PRECAUTIONS AND GENERAL RECOMMENDATIONS
ENERGY SAVING TIPS
OK!
NO!
21
• Accessories supplied depend on the model
(refer to the Product Description Sheet
supplied separately).
Drip tray
The drip tray is designed to collect fat and food
particles when it is positioned under the grid;
it can also be used as a griddle to cook meat, chicken
and fish, with or without vegetables. When using the
drip tray under the grid, pour in a little water to avoid
fat spatters and smoke.
Baking tray
For cooking biscuits, meringues and pizzas.
Grid
The grid can be used to grill food or as a support for
baking trays, cake tins and other cooking receptacles.
It has two possible positions ( or ) and can be
placed on any of the runners in the oven.
Catalytic panels (depending on model)
The catalytic panels have a microporous coating that
absorbs fat spatters. We recommend an automatic
cleaning cycle after cooking particular fatty food.
1.
To clean the oven heat it to 200°C when empty and
leave it switched on for about
an hour.
2.
At the end of the cycle and when the oven is cool,
use a moist sponge to remove food residues if
necessary.
Do not use detergent or cleaners - risk of
damaging the catalytic enamel coating.
Spit (depending on model)
Use the spit as indicated in the relevant chapter in the
Product Description Sheet supplied separately.
Child guard accessory AMH 122
This accessory can be obtained from the After Sales
Service under Part N° 4819 310 18436 or from your
Dealer under Ref. 017124.
OVEN ACCESSORIES
COOKTOP ACCESSORIES
1
2
3
4
5
1
2
3
4
5
22
.
N.B.: Cooking times and temperatures are purely guidelines. Oven functions depend on the
model. Refer to the separate Product Description Sheet.
COOKING CHARTS
Food
Static function Fan function Static function +Fan
Temp.°C
Runner
from
bottom
Cooking
Time
(Mins.)
Temp.°C
Runner
from
bottom
Cooking
Time
(Mins.)
Temp.°C
Runner
from
bottom
Cooking
Time
(Mins.)
Meat
Lamb (1,5Kg) 220 2 80-90 200 2 75-85 180 2 70-80
Kid (1,5 Kg) 220 2 80-90 200 2 75-85 180 2 70-80
Mutton (1,5 Kg) 220 2 80-90 200 2 75-85 180 2 70-80
Veal (1,5 Kg) 220 2 80-90 200 2 75-85 175 2 70-80
Beef (1 Kg) 220 2 70-80 200 2 65-75 175 2 60-70
Pork (1 Kg) 220 2 70-80 200 2 65-75 175 2 60-70
Rabbit (1,5 Kg) 220 2 80-90 200 3 75-85 180 2 70-80
Chicken (1 Kg) 220 2 65-75 200 2 60-70 200 2 55-65
Turkey(3 Kg) 220 2 140-160 200 2 130-150 180 2 120-140
Goose (2 Kg) 220 2 100-120 200 2 90-100 200 2 85-95
Duck (1,5 Kg) 220 2 80-90 200 2 75-85 200 2 70-80
Fish (approx 1 kg)
Gilt head 200 2 45-55 180 2 40-50 170 2 40-50
Bass 200 2 45-55 180 2 40-50 170 2 40-50
Salmon 200 2 45-55 180 2 40-50 170 2 40-50
Tuna 200 2 45-55 180 2 40-50 170 2 40-50
Trout 200 2 45-55 180 3 40-50 170 2 40-50
Fish steaks (1 kg)
Swordfish 200 2 45-55 180 3 35-45 170 2 30-40
Tuna 200 2 40-50 180 3 35-45 170 2 30-40
Salmon 200 2 40-50 180 3 35-45 170 2 30-40
Cod 200 2 40-50 180 3 35-45 170 2 30-40
Fillet 200 2 40-50 180 3 30-35 170 2 30-40
Vegetables
Stuffed peppers 200 2 40-50 180 2 40-50 170 2 45-55
Stuffed tomatoes 200 2 60-70 180 3 55-65 180 2 50-60
Baked potatoes 200 2 60-70 200 3 55-65 190 2 55-65
Au gratin 200 2 70-80 200 3 65-75 190 2 60-70
Desserts etc.
Cakes 160 2 35-45 150 3 30-40 150 2 40-50
Cake with filling
(fruit - cheese)
180 2 40-50 160 3 45-55 160 2 45-55
Tarts 180 2 40-50 160 3 45-55 170 2 40-50
Apple strudel 200 2 45-55 190 3 45-50 180 2 45-55
Biscuits 180 2 30-40 150 1-3 25-35 140 2-4 20-30
Choux pastry 180 2 30-35 170 2-3 30-40 170 2-4 30-35
Pies 180 2 50-60 160 3 45-55 170 2 50-60
Bread 250 2 50-60 220 2 50-60 220 2 50-60
Pizza 250 2 20-30 250 1-3 30-40 250 2 20-30
Lasagne 220 2 35-45 200 3 35-45 190 2 35-45
Vol-au-vents 225 2 15-20 200 1-3 15-20 190 2-4 15-20
Soufflès 200 2 40-50 180 2 45-55 180 2 40-50
23
N.B.: Cooking times and temperatures are purely guidelines. Oven functions depend on the
model. Refer to the separate Product Description Sheet.
•
When you finish cooking, wait for the oven to
cool and then clean it to prevent the build-up
of baked-on residues.
•
If the food residues are baked on, use a
specific oven cleaner and follow the
manufacturer’s instructions on the pack.
•
Clean the exterior of the oven with a sponge
and warm water.
• Do not use abrasive cleaners or pan
scourers.
•
Use a liquid detergent to clean the oven door
window.
•
Wash the accessories in a dishwasher or in
the sink, using an oven cleaner.
•
After the oven has been in prolonged use and
when cooking on different levels (especially
food with high water contents such as pizzas,
stuffed vegetables, etc.) condensation may
form on the inside of the door seal.
When the oven is cool, dry any condensation
with a cloth or sponge.
COOKING CHARTS
Food
Grill function Grill + Fan function
Temp. °C
Runner
from
bottom
Cooking
Time
(Mins.)
Temp. °C
Runner
from
bottom
Cooking
Time
(Mins.)
Sirloin steak 250 4 20-30 225 3 30-40
Cutlets 250 4 15-20 225 3 20-40
Sausages 250 4 20-30 225 3 30-40
Pork chops 250 4 20-30 225 3 30-40
Fish 225 4 15-25 220 3 20-30
Chicken drumstick 225 4 15-25 200 3 25-35
Kebabs 225 4 20-30 200 3 35-45
Spare ribs 225 4 30-40 200 3 40-50
Chicken halves 225 3 35-45 200 3 40-50
Whole chicken - - - 200 3 60-70
Roast (pork, beef, veal) (~ 1kg) - - - 175 2 90-100
Duck - - - 180 2 90-120
Leg of lamb - - - 200 2 80-90
Roast Beef - - - 200 2 50-60
CLEANING THE OVEN AND ACCESSORIES
24
Removing the oven door (for cleaning)
1.
Open the oven door.
2.
Press hinge catches (
A
) forwards.
3.
Lift the catches until they engage and then remove
the door.
4.
While you are cleaning the oven, ensure you do
not disengage the hinge retainer catches.
5.
Refit the oven door by following the above steps in
reverse order.
Dropping the grill element to clean the oven roof
(depending on model)
•
Do not attempt to clean the oven until it is cool.
1.
To clean the oven roof, pull out the grill element
and lower it as far as it will go.
2.
Clean the oven roof and then return the grill
element to its original position.
Changing the oven lamp
1.
Disconnect the oven from electrical supply.
2.
Unscrew the lamp cover.
3.
Change the lamp (see N.B.).
4.
Refit the lamp cover.
5.
Reconnect the electrical supply.
Changing the lateral lamp (depending on model)
1.
Disconnect the oven from electrical supply.
2.
Remove the left hand side grid.
3.
Use a screwdriver to prize off the lamp cover.
4.
Remove the bulb (see N.B) from the ceramic
holder. Fit the new bulb using plastic gloves, or
degrease it with alcohol.
5.
Reposition the lamp cover and press it against the
oven wall until it clicks into place.
6.
Refit the side grid.
7.
Reconnect the power supply.
N.B:
Use exclusively 20 W, 12 V, G4 type, T300° C
lamps only, available from After Sales Service.
.
CLEANING THE OVEN AND ACCESSORIES
25
Before cleaning the cooktop, disconnect it from
the electrical supply and wait until it has cooled.
Care and Maintenance of conventional
cooktop
•
Use a cloth and warm soapy water.
•
Do not use abrasives, corrosive cleaners,
cleaners containing chlorine or pan scourers.
•
Do not leave acidic substances on the
cooktop (vinegar, salt, lemon juice, etc.).
Stainless steel cooktop
•
Use a proprietary cleaning product for
stainless steel.
N.B:
Prolonged use of the cooktop may result in
slight discoloration of the stainless steel surfaces
around the hotplates. This is caused by the high
temperature of the hotplates.
Cleaning the hotplates
Clean the hotplates when they are warm
(not hot!). Use a cloth moistened with water and
salt. Dry and clean with a cloth moistened with
cooking oil.
Clean the cooktop, when it is cool, after each
use. This will prevent the build-up of dirt and
make cleaning easier.
•
Use a clean cloth, absorbent kitchen wipes
and washing up liquid or a specific
glass-ceramic hob cleaner.
•
Remove baked-on dirt with the supplied
scraper tool and specific cleaning products.
•
Food spills should be cleaned off before they
bake onto the glass-ceramic surface.
•
Do not use abrasive products, bleach,
oven-cleaner spray or pan scourers.
•
The cooktop should be treated periodically
with a proprietary brand of protective wax for
glass-ceramic hobs.
Oven not working
•
Switch the oven off and then on again to see
if the problem persists.
•
Check for the presence of mains electrical
power.
•
Oven selector on position “0” ?
•
Check whether you have made the
temperature setting and the function setting.
•
If the electronic programmer display presents
the message “OFF”, press any key to reset
the oven and then set the clock.
•
Ensure that the analogue programmer
(depending on model) is set to .
Cooktop not working
•
Ensure that the cooktop is receiving electrical
power.
•
Control knob set to “0”?
Set the main disconnect switch upline of the
appliance to “OFF” for a few minutes and
then back to “ON” and see if the problem
persists.
CARE AND MAINTENANCE OF
CONVENTIONAL ELECTRIC COOKTOPS
CARE AND MAINTENANCE OF
GLASS-CERAMIC COOKTOPS
TROUBLESHOOTING GUIDE
26
Before contacting After Sales Service:
1.
Try to solve the problem (see “Troubleshooting
Guide”).
2.
Turn off the appliance and restart it to see if the
fault is repeated.
If after the above checks the fault still occurs, get
in touch with the nearest After Sales Service.
Please give:
•
a short description of the fault,
•
the exact type and model,
•
the service number (number after the word Service
on the rating plate) is located on the underside of
the cooktop or on the Product Description Sheet
and on the right hand edge of the oven cavity
(visible when the oven door is open). The service
numbers are also indicated on the guarantee
booklet,
•
your complete address and phone number.
•
These appliances are designed to come into
contact with foodstuffs and they are constructed in
compliance with Directive 89/109/EEC.
•
The appliances are designed solely for use as
cooking appliances. Any other use of the
appliances (e.g. for room heating) is considered as
improper use and potentially dangerous.
•
The appliances are designed, built and sold in
compliance with:
- the safety requirements of “Low Voltage”
Directive 73/23/EEC,
- the protection requirements of EMC Directive
89/336/EEC,
- the requirement of Directive 93/68/EEC.
•
This appliance complies with Class “
Y
” fire
protection category.
AFTER SALES SERVICE
DECLARATION OF CONFORMITY CE
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Whirlpool OBU 245 Owner's manual
- Category
- Ovens
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool OBU 256 W User guide
-
-
-
-
Whirlpool AKZ 301 User guide
-
Whirlpool AKZ 315 WH User guide
-
-
-
Whirlpool AKP 711 NB Owner's manual
-
Whirlpool BSN 3000/01 User guide