Edelbrock Edelbrock Flathead 1949-53 Generator Bracket waterneck kit Satin Installation guide

Edelbrock
Brand
Edelbrock
Model
Edelbrock Flathead 1949-53 Generator Bracket waterneck kit Satin
Type
Installation guide

This manual is also suitable for

Edelbrock Flathead 1949-53 Generator Bracket waterneck kit Satin installs before the offset generator bracket and is used as a replacement for the stock unit. It is compatible with Edelbrock Manifold #1109 and late model cylinder heads that have a front mounted water neck. The kit includes a clevis, cotter pins, and the necessary hardware for installation. The generator bracket can be adjusted up and down to achieve the proper belt tension. The stock bracket mounted fan assembly can be attached to the two threaded holes drilled in the generator bracket.

Edelbrock Flathead 1949-53 Generator Bracket waterneck kit Satin installs before the offset generator bracket and is used as a replacement for the stock unit. It is compatible with Edelbrock Manifold #1109 and late model cylinder heads that have a front mounted water neck. The kit includes a clevis, cotter pins, and the necessary hardware for installation. The generator bracket can be adjusted up and down to achieve the proper belt tension. The stock bracket mounted fan assembly can be attached to the two threaded holes drilled in the generator bracket.

EDELBROCK OFFSET GENERATOR BRACKET & WATER NECK
for Flathead Ford V8 Engines using Edelbrock Manifold #1109
Part #1146
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new Generator Bracket and Water Neck. If you have any questions,
please contact our Technical Hotline at: 1-800-416-8628, 7:00 am to 5:00 pm, Monday through Friday, Pacific Standard Time.
1. Install the #1109 intake manifold before attempting to
install the offset generator bracket.
2. Install the generator bracket so that the horseshoe shaped
machined surface slides into the groove at the front end of
the manifold. The arm of the bracket should extend toward
the passenger side fender.
3. Secure the bracket in place with the stock generator
mounting bracket nut, but only hand tighten it at this time.
4. Locate the looped end of the stock hold down strap inside
the bracket recess and secure it with the supplied clevis
and cotter pins.
5. Fit the generator into the bracket with the pulley facing the
front of the engine, then fold the strap over the generator
INSTALLATION INSTRUCTIONS
and secure it to the bracket with the stock 1/4”-20 bolt.
Adjust belt tension on the generator by sliding the bracket
up and down until the proper tension is achieved, then
torque the nut to spec.
6. Late model cylinder heads (front mounted water neck) will
need to use the supplied offset water neck in place of the
stock unit. Early model heads have a water neck cast into
the heads themselves, and may discard the supplied water
neck.
7. The stock bracket mounted fan assembly can be attached
to the two threaded holes drilled in the generator bracket.
8. Recheck the generator belt tension after the engine has
been run and adjust if necessary.
©2009 Edelbrock Corporation
Part #1146
Brochure #63-1146
Rev. 5/09 - AJ/mc
EDELBROCK OFFSET GENERATOR BRACKET & WATER NECK
for Flathead Ford V8 Engines using Edelbrock Manifold #1109
Part #1146
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new Generator Bracket and Water Neck. If you have any questions,
please contact our Technical Hotline at: 1-800-416-8628, 7:00 am to 5:00 pm, Monday through Friday, Pacific Standard Time.
1. Install the #1109 intake manifold before attempting to
install the offset generator bracket.
2. Install the generator bracket so that the horseshoe shaped
machined surface slides into the groove at the front end of
the manifold. The arm of the bracket should extend toward
the passenger side fender.
3. Secure the bracket in place with the stock generator
mounting bracket nut, but only hand tighten it at this time.
4. Locate the looped end of the stock hold down strap inside
the bracket recess and secure it with the supplied clevis
and cotter pins.
5. Fit the generator into the bracket with the pulley facing the
front of the engine, then fold the strap over the generator
INSTALLATION INSTRUCTIONS
and secure it to the bracket with the stock 1/4”-20 bolt.
Adjust belt tension on the generator by sliding the bracket
up and down until the proper tension is achieved, then
torque the nut to spec.
6. Late model cylinder heads (front mounted water neck) will
need to use the supplied offset water neck in place of the
stock unit. Early model heads have a water neck cast into
the heads themselves, and may discard the supplied water
neck.
7. The stock bracket mounted fan assembly can be attached
to the two threaded holes drilled in the generator bracket.
8. Recheck the generator belt tension after the engine has
been run and adjust if necessary.
©2009 Edelbrock Corporation
Part #1146
Brochure #63-1146
Rev. 5/09 - AJ/mc
Edelbrock Corporation
2700 California St., Torrance, CA 90503
Edelbrock Corporation
2700 California St., Torrance, CA 90503
  • Page 1 1

Edelbrock Edelbrock Flathead 1949-53 Generator Bracket waterneck kit Satin Installation guide

Edelbrock
Brand
Edelbrock
Model
Edelbrock Flathead 1949-53 Generator Bracket waterneck kit Satin
Type
Installation guide
This manual is also suitable for

Edelbrock Flathead 1949-53 Generator Bracket waterneck kit Satin installs before the offset generator bracket and is used as a replacement for the stock unit. It is compatible with Edelbrock Manifold #1109 and late model cylinder heads that have a front mounted water neck. The kit includes a clevis, cotter pins, and the necessary hardware for installation. The generator bracket can be adjusted up and down to achieve the proper belt tension. The stock bracket mounted fan assembly can be attached to the two threaded holes drilled in the generator bracket.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents