Panasonic CQDVR909N Operating instructions

Brand: Panasonic

Model: CQDVR909N

Category: CD players

Type: Operating instructions

CQ DVR909N CQ DVR909N

28 29

Common Operations

/ R

MUTE

SUB TITLE

ANGLE

REPEAT

STOP

PAUSE

PLAY

BAND

ST/MONO

TITLE /

CHAPTER

LUM

TITLE

RETURN

CAR DVD PLAYER

DISP

GRP

Power

≥ Turn the power on.

≥ The first time that you turn the unit on,

the radio will begin playing and the

message “Panasonic Presents ……”

(demonstration mode) will be

displayed.

To cancel the demonstration mode:

To turn the power off:

Note:

≥ Loading/ejecting a disc also turns the

power on/off. (➡ page 38)

Volume

(Adjustable range: 0 to 40)

:Increases

the volume.

:Decreases the

volume.

Note:

≥ When you switch the source, the

volume that was set last for that

source is restored.

POWER

SOURCE

Before performing any of these operations, turn your car’s ignition switch to “ACC” or “ON”.

(depends on the disc)

(When DAB receiver

is connected)

(When a separate CD

changer is connected)

AUXILIARY

DAB Receiver

CHANGER

DVD VIDEO

TUNER

(Radio)

(Auxiliary source)

Audio Source

POWER

SOURCE

POWER

SOURCE

VOLUME

A C D

SOURCE

POWER

SPEAKER

OPEN/CLOSE

VOL

To turn the

power off:

SOURCE

POWER

Press

Hold (1 second)

Center Speaker

≥ Press the button to open and close

the center speaker.

≥ To open the center speaker through the

remote control while playing a DVD or a

video CD, hold the button down for

more than 2 seconds.

Notes:

≥ You can adjust the output level/

volume of the center speaker.

(➡ pages 27, 53)

≥ You cannot open or close the center

speaker while the panel is open.

C.SP

Press

%$, SEL

(SELECT)

DISP

(DISPLAY)

6 TRACK 5

SEL(SELECT)

OPEN•

TILT

When using the main unit

CLOCK

DISP

Press

You can adjust the tilt of the panel to make it easier to see.

Note:

≥ The panel will open to the angle of tilt that you have

previously set whenever you turn the ignition switch to

“ACC” or “ON”.

To close the panel:

Notes:

≥ If no button is pressed for about

20 seconds, the panel closes

automatically and returns to the

angle of tilt that you have previously

set.

≥ The panel closes completely when

the ignition switch is turned to “OFF”.

OPEN

TILT

OPEN

TILT

OPEN

TILT

OPEN

TILT

Tilting the Panel

Opening/Closing the Panel

Caution:

≥ Do not attempt to manually move or

stop or strike the panel or the

center speaker.

≥ The panel opens.

When the panel is open, this

unit is muted and you can not

operate except for some

buttons.

≥ The panel closes and returns to

the angle of tilt that you have

previously set.

≥ The panel closes completely,

and the tilt setting is cancelled.

≥ To change the tilt of the panel, hold the

button down for more than 1 second.

<The tilting mechanism has three tilt

positions.>

Press

Hold

(1 second)

Hold

Tilt 1

Tilt 2

Tilt 3

Open

If your car has ACC, turn it ON. Otherwise, turn it OFF.

ACC Selection

Indicates pressing

a button.

Indicates pressing a

button for an extended

period of time.

Indicates operations

that can only be

performed through

the main unit.

1 Switch to setting mode. 2 Select “ACC SELECT”. 3 Make setting.

SEL

(Main unit: )

(Main unit: ) (Main unit: )

ACC SELECT

Hold

(2 seconds)

SEL

TUNE

TRACK

RACK

: ACC ON (ACC

provided)

: ACC OFF (ACC

not provided)

Press

CQ DVR909N CQ DVR909N

30 31

Radio Basics

Indicates pressing a button.

Indicates pressing a button

for an extended period of time.

/ R

MUTE

SUB TITLE

ANGLE

REPEAT

STO

PAUSE

PLAY

BAND

ST/MONO

TITLE /

CHAPTER

TRACK

VOLUME

TITLE

RETURN

CAR DVD PLAYER

DISP

GRP

MAIN

•

Band

Preset Number

Frequency

Lights when an FM stereo

broadcast is received.

Select the station

:Increases the frequency.

: Decreases the frequency.

≥ The frequency changes each time one

of these buttons is pressed. <step

mode>

≥ If you hold down the button for more

than 0.5 second and then release the

button, the tuner will begin scanning

frequencies in that direction, and then

will stop when it picks up a station.

CLOCK

DISP

Changing the Display

Normal display Clock displayProgram Service Name Display off

(band/

preset number/

frequency)

Select “TUNER”

Select the band

POWER

SOURCE

PLAY

BAND

1 2 3

SOURCE

POWER

BAND

AUTO

•

TUNE

TRACK

FM 3AM (LW/MW)

FM 1 FM 2

Press

Number Buttons

(1j6)

DISP

(DISPLAY)

# P

•

SET "

(PRESET)

When using the main unit

You can store presets for up to 6 stations in each AM (LW/MW) and FM band

(up to a maximum of 24).

After selecting a band and a station... After selecting a band...

After selecting a band...

≥ The stored station is received.

BAND

PLAY

321

4 5 6

321

4 5 6

1 2 3

4 5 6

Setting Up Station Presets

Listening to a Preset Station

≥ When the station is stored in the preset,

the frequency will blink once.

Manual Preset Memory

Auto Preset Memory

Using the buttons on the main unit

Set preset mode.

≥ The preset number blinks.

Select a preset number.

Select the station.

Store the station in the preset.

≥ The preset number stops blinking,

and the frequency blinks once.

To cancel during setting procedure:

DISC

P•SET

DISC

P•SET

TUNE

TRACK

DISC

P•SET

≥ Starting from the low end of the

frequency spectrum, the unit will begin

storing each station that it picks up with

clear reception in preset numbers 1

through 6.

≥ When a station is stored in a preset, the

preset number blinks for about

5 seconds, and then the next preset

number is called up. <preset scan

mode>

To stop preset scanning:

Select a preset number.

Using the buttons on the main unit

Select a preset number.

DISC

P•SET

Press

Hold

(2 seconds)

Hold

(2 seconds)

Press

Hold (2 seconds)

Press

(Main unit: )

DISC

P•SET

(Main unit: )

AUTO•P

BAND

CLOCK

DISP

(FM broadcast only)

CQ DVR909N CQ DVR909N

32 33

Radio Basics

(continued)

Radio Data System (RDS)

(continued)

Radio Data System (RDS)

Monaural Mode: Monaural reception. Turn Mono On to reduce noise when receiving a stereo

broadcast.

Local Mode : Tunes in strong stations only.

Mono/Local Selection

The following functions are available when receiving RDS stations.

Program Service Name Display (PS Display): The name of station is displayed instead of the

frequency.

Clock Time Service (CT Service): When receiving an RDS station, the CT (Clock Time) service

automatically adjusts the time. “NO CT” is displayed in areas where CT service is not available. (➡

page 37 about “Setting the Clock”)

Alternative Frequency (AF): When reception is poor, an RDS station broadcasting the same

program is tuned in automatically.

RDS Basic

AF Mode

Auto Preset Memory

Auto Preset Memory works only for RDS

stations when AF mode is on. (➡ page 31

about auto preset memory.)

REG (Region) Mode

Changes the selection range of AF and Best Station Research.

AF Level

DIMR

AF DIMMER

Hold (2 seconds)

Hold

(2 seconds)

Press

AF ON

AF OFF

AF LEVEL 1

AF LEVEL 2

REGION ON

REGION OFF

12 3

2 Switch to AF level setting mode.

3 Set AF level.

Hold (2 seconds)

FUNCTION

2 Switch to Region mode.

3 Set Region on or off.

(Low level AF operating sensitivity)

(High level AF operating sensitivity)

The frequency is changed only for

programs within the region.

The frequency is changed also for

programs outside the region.

(When receiving a PS station) Best Station Research

Best Station Research is automatically

activated to store the station with the best

reception for each preset number.

BBCR1 FM1 102.50

10 : 29

TUNER

(Program Service Name) (Frequency) (Clock display) (Display off)

Press

DIMR • AF

(DIMMER) (ALTERNATIVE FREQUENCY)

TA • FUNCTION

(TRAFFIC

ANNOUNCEMENTS)

SEL

(SELECT)

6TRACK5

DISP/CT•PTY

(DISPLAY/

CLOCK TIME)

FUNCTION

SEL

Press

SEL

Select “MONO SELECT” or

“LOCAL SELECT”.

Switch Mono (Local) on or off.

TUNE

TRACK

TUNE

TRACK

Press

TUNE

TRACK

MONO

PTY

EON

TAon

MAIN

LOCAL

RDS

Lights when Mono is on.

Lights when

Local is on.

Lights when

Radio Data

System is received.

Lights when Traffic

Program is received.

Lights when Traffic

Announcements mode is on.

Lights when Enhanced

Other Networks is received.

Lights when Program Type

mode is on.

Lights when Alternative

Frequency mode is on.

DISP/CT

PTY

Changing the Display

Press

(PROGRAM

TYPE)

Perform these operations with the main unit.

Press

CQ DVR909N CQ DVR909N

34 35

Radio Data System (RDS)

(continued)

RDS FM stations provide a program type identification signal.

Example: news, rock, classical music, etc.

Program Type (PTY) Display

DISP/CT

PTY

News

BBCR 1

PTY display mode

Following functions are activated.

PTY Mode

PTY Selection PTY Display Language

123

2 After selecting a program,

BAND

AUTO•P

≥ Seek will start to tune in to a station

broadcasting the selected program type.

DISP/CT

PTY

Hold (2 seconds)

(Program Service Name)

Press

English Germany

Swedish

ItalianFrench

Dutch

Spanish

PTY Preset

Program types are stored in memory under preset numbers 1 to 6 shown in the table below.

DISC

P•SET

Press

Preset No. Program Type

News 1

Classics 5

SPEECH 2

News

Sport

Pop. Music

Other Music

Classic Music

Speech

News

Sport

Pop M

Classics

Rock M/Easy M/Light M/Other M/Jazz/Country/

Nation M/Oldies/Folk M

Affairs/Info/Educate/Drama/Culture/Science/Varied/

Weather/Finance/Children/Social/Religion/Phone In/

Travel/Leisure/Document

Display Contents

Press

1 Select the preset number. 2 Tune in the desired program type

station.

BAND

AUTO•P

Press

PTY Preset Change

After selecting a program type,

DISC

P•SET

Hold (2 seconds)

DISC

P•SET

Press

DISC

P•SET

Hold (2 seconds)

BAND/AUTO•P

(AUTO•PRESET)

6TRACK5

#DISC"

DISP/CT•PTY

(DISPLAY/

CLOCK TIME)

TUNE

TRACK

(PROGRAM TYPE)

To tune in the desired program type:

Sport 3

Pop M 4

MUSIC 6

SPEECH MUSIC News Affairs

Info

Culture

Rock M

Other M

Social

Leisure

Oldies

Sport

Science

Easy M

Weather

Religion

Jazz

Folk M

Educate

Varied

Light M

Finance

Phone In

Country

Document

Drama

Pop M

Classics

Children

Travel

Nation M

SPEECH

CQ DVR909N CQ DVR909N

36 37

Radio Data System (RDS)

(continued)

Others

Enhanced Other Networks (EON)

When EON data is received, the EON indicator lights and the TA and AF functions are expanded as

follows.

TA: Traffic information from the current and other network stations can be received.

AF: The frequency list of preset RDS stations is updated by EON data.

EON enables the radio to make fuller use of RDS information. It constantly updates the AF list of

preset stations, including that currently tuned in to. For example, if you preset a station far from

home, you will later be able to receive the same station at an alternative frequency, or any other

station serving the same program. EON also keeps track of locally available TP stations for quick

reception.

Emergency Announcement Reception

When an emergency announcement is broadcast, the unit is automatically switched to receiving

that broadcast. If this happens in a mode other than radio mode (disc mode, CD changer mode,

auxiliary mode) or in Muting in TA mode, “Alarm!” blinks on the display.

Some RDS FM stations periodically provide traffic information.

Traffic Program (TP): Broadcasting of traffic information

Traffic Announcements (TA): Radio announcements on traffic conditions

Traffic Announcement

TA Mode

TA Volume Set

(Adjustable range: 1 to 40)

TA Stand By

Even when Disc, CD changer or auxiliary mode is selected, FM

traffic announcement will interrupt them.

FUNCTION

≥ Each time the button is pressed, TA mode swiches to on or off.

≥ When TA mode is on, “TAon” lights and receive traffic announcements

automatically. Following functions are activated.

Note:

≥ Seek tuning and auto preset memory work only for TP stations when TA mode is on.

Hold (2 seconds)

2 Adjust TA volume.

FUNCTION

VOL

Press

Muting in TA mode

To listen only to traffic announcement while

muting.

1 Adjust the TA volume.

2 Set the regular volume level to 0.

(➡ page 28)

When receiving an RDS station, the CT (Clock Time) service automatically adjusts the time.

(➡ page 33) If CT service is not available, set the clock as follows.

1 Select the AM band.

DISP/CT

PTY

Setting the Clock

To display the time:

Press the button repeatedly

until the time is displayed.

≥ “NO CT” will be displayed

when the clock is not

adjusted.

DISP/CT

PTY

Hold

(2 seconds)

Press

Switch between the hours and minutes displays, and set

both.

: Selects the hours display,

which begins to blink.

: Selects the minutes display,

which begins to blink.

: Increases the number in the

selected display.

: Decreases the number in the

selected display.

Finalize the time setting.

≥ The clock begins to run.

TUNE

TRACK

UNE

TRACK

DISC

P•SET

DISC

P•SET

DISP/CT

PTY

Press

0 : 00

10 : 35

TA • FUNCTION

(TRAFFIC

ANNOUNCEMENTS)

6TRACK5

#DISC"

#VOL"

(VOLUME)

DISP/CT•PTY

(DISPLAY/

CLOCK TIME)

Press

(PROGRAM TYPE)

BAND/AUTO•P

(AUTO PRESET)

BAND

AUTO•P

Press

CQ DVR909N CQ DVR909N

38 39

DVD Audio

•

Video/Video CD/CD Basics

CQ DVR909N CQ DVR909N

38 39

Notes:

≥ If a disc is inserted while the power is off,

the power turns on.[When ACC Selection is

set to ON. (➡ page 29)]

Indicates pressing a button.

Indicates pressing a button

for an extended period of time.

/ R

MUTE

SUB TITLE

ANGLE

REPEAT

STOP

PAUSE

PLAY

BAND

ST/MONO

TITLE /

CHAPTER

LUME

TITLE

RETURN

CAR DVD PLAYER

DISP

GRP

Label side

Perform these operations with the remote control.

Before performing any operation, check the TV connection setting (➡ page 47).

Operations vary according to the disc. For details, refer to the guide provided with the disc.

Open the panel

Insert the disc

(It takes a few seconds to load a disc after the

panel opens. If you force to insert the disc by

hand, the disc may be damaged.)

≥ The panel closes and the disc begins playing.

≥ The type of disc is automatically discriminated.

OPEN

TILT

Removing a disc

Cautions:

≥ Do not obstruct the opening/closing of the panel.

≥ When the panel is fully open (no sound is output),

do not apply excessive pressure to the panel or

push hard on the buttons on the panel.

Press

Inserting/Removing the Disc

Starting Playback

Select the disc mode

(Example: “DVD AUDIO”)

≥ Playback starts.

POWER

SOURCE

Press

DISP

(DISPLAY)

REP

DR COMP

DIGITAL

LFE

MAIN

kHz

bit

16 20 24

Lights when disc is loaded.

Lights when car is moving.

(TV picture does not appear. Turns off when car

is stopped and parking brake is applied.)

Lights/blinks during

repeat playback.

Blinks when attempt is

made to perform an

operation prohibited by

this unit or the disc.

Number of quantization bits (➡ page 79)

Sampling

frequency

(➡ page 79)

DVD Audio

DVD Video

Video CD

CLOCK

DISP

Changing the Display

AUDIO 01`02 02 00 : 00’ 01

14 : 22 DVD AUDIO

(Group number)

(Track number) (Elapsed playback time) (Clock display) (Display off)

(Track number)

VIDEO 01`003 003 00 : 00’ 01

14 : 22 DVD VIDEO

(Title number)

(Chapter number) (Elapsed playback time) (Clock display) (Display off)

(Chapter number)

00 : 00’ 01

14 : 22 VCD

(Elapsed playback time) (Clock display) (Display off)

CD 01 0’ 01

14 : 22 CD

(Track number)

(Elapsed

playback time)

(Clock display) (Display off)

Press

VCD

≥

During playback of Dolby Digital encoded material,

setting “DR COMP ON” will make comparatively

quiet sounds easier to hear. (➡ page 59)

Some DVD discs have unique menu structures called DVD menu. DVD discs programmed with

complex contents provide guide menus, and those recorded with various languages provide

menus, audio and subtitle languages. Although the DVD menu’s contents and operation differ

from disc to disc, the following explains basic operation when this feature is used. Please refer

to “DVD Menu” (➡ page 43) or “Title Menu” (➡ page 45) for further instructions.

CQ DVR909N CQ DVR909N

40 41

DVD Audio

•

Video/Video CD/CD Basics

(continued)

/ R

MUTE

SUB TITLE

ANGLE

REPEAT

STO

PAUSE

PLAY

BAND

ST/MONO

TITLE /

CHAPTER

VOLUM

TITLE

RETURN

CAR DVD PLAY

DISP

GRP

Selecting a Menu Item

Stopping

DVD

(Select item) (Finalize selection)

Example)

MAIN MENU

Live (Part 1)

Live (Part 2)

Back stage

SEL

To return to the previous

menu screen or to re-input

a number:

DVD/Video CD with playback control

321

4 5 6

7 8 9

(Select item) (Finalize selection)

Select your favorite music

1. Love Supremes

2. Impressions

3. In a sentimental mood

RETURN

Notes:

≥ Pressing [9][:]

while a video CD with

playback control is being

played may cause you to

return to the menu screen.

≥ Operations vary according

to the disc. For details,

refer to the guide provided

with the disc.

≥ “STOP” blinks.

≥ Pressing [PLAY1] causes playback to resume from the location where it

stopped. (Continued playback function)

(During stop, press [STOP∫] again to cancel continued playback and “STOP”

turns to light.)

STOP

SEL

Press

"#%$, SEL

(SELECT)

:, 9 (Backward, Forward)

PLAY 1

PAUSE ;

Number Buttons

STOP ∫

REPEAT

RETURN

Fast Forward/Fast Backward

Go to Beginning

Pause

Repeat

(Backward) (Forward)

≥ The speed changes if the button is held down (maximum

20 times as fast as normal speed). Playback begins at the

point where the button is released.

≥ Each time one of these buttons is pressed, the player jumps

to the start of the appropriate track (chapter).

≥ If the backward button is pressed once, the player returns to

the start of the track (chapter) that is currently being played.

(During playback)

PAUSE

≥ “PAUSE” is displayed and

the playback pauses.

PLAY

BAND

PAUSE

≥ “REP” lights.

DVD audio/video CD/CD

“TRACK REP ON” is displayed

and the track that is currently

being played repeats.

DVD video

“CHAPT REP ON” is displayed

and the chapter that is

currently being played repeats.

≥ “REP” blinks.

DVD audio

“GROUP REP ON” is displayed

and the group that is currently

being played repeats.

DVD video

“TITLE REP ON” is displayed

and the title that is currently

being played repeats.

REPEAT

To resume normal playback:

REPEAT

Note:

≥ When playing a DVD audio

(video), there are cases

where it is not possible to

return to the start of a track

(chapter) that spans

2 groups (titles).

To resume normal playback:

Hold

Press

Hold

(2 seconds)

Chapter/Track Repeat Group/Title Repeat

To resume normal playback:

REPEAT

Hold (2 seconds)

CQ DVR909N CQ DVR909N

42 43

DVD Audio

•

Video/Video CD/CD Basics

(continued)

Starting Playback from a

Specific Group/Track/Title/Chapter

1 (During playback)

Select the input mode.

Track (Chapter) input mode

[Track (Chapter) number blinks.]

Group (Title) input mode

[Group (Title) number blinks.]

Input the desired group/track/title/chapter

number.

≥ Playback starts.

321

4 5 6

7 8 9

TRACK

TITLE/

CHAPTER

GRP

Playing back a bonus group (*)

(DVD audio only)

1 Select the group number

input mode.

2 Input the bonus group

number.

3 Input the security code.

4 Finalize selection.

TRACK

TITLE/

CHAPTER

GRP

TRACK

TITLE/

CHAPTER

GRP

≥ “KEY NUM :----” is

displayed.

To return to normal mode:

To re-input the number:

CLOCK

DISP

SEL

This is a group that contains only DVD audio

software, and cannot be played without

entering a security code. (Some software

does not include bonus groups.) For details,

refer to the guide provided with your disc.

TRACK

TITLE/

CHAPTER

GRP

Press

/ R

MUTE

SUB TITLE

ANGLE

REPEAT

STOP

PAUSE

PLAY

BAND

ST/MONO

TITLE /

CHAPTER

TRACK

VOLUM

TITLE

RETURN

CAR DVD PLAYE

DISP

GRP

01 / 003

Press

Regular mode

"#%$, SEL

(SELECT)

PAGE + –

GRP

(GROUP)

Number Buttons

RETURN

DISP

(DISPLAY)

AUDIO

MENU • TITLE

Note:

(DVD audio only)

≥ Press and hold [GRP] for more than

2 seconds, and the player jumps to the

start of the next group.

Use this menu during playback to select content, audio, subtitles, etc., from a menu

(the DVD menu) that is unique to each disc.

It is possible to move only the still image forward or backward while music continues to play.

Switching the Audio Language

DVD Menu

Still Forward/Backward

(During playback)

DVD audio DVD video

(maximum: 2)

(maximum: 8)

≥ This operation will

sometimes cause

the player to jump to

the beginning of the

track that is

currently being

played.

Notes:

≥ The number of audio languages

depends on the disc. (Some discs

have only one language.)

≥ It may not be possible to switch

languages unless the unit is at the

DVD menu or is at the initial

settings (➡ page 46).

AUDIO

1 (During playback)

TITLE

≥ “PLAY” is displayed and the DVD

menu appears on the screen.

(Pressing this button again causes

playback to start at the scene from

which the DVD menu was called.)

Example)

(Select item)

(Finalize selection)

To return to the previous

menu screen:

Note:

≥ DVD menu content and

operations depend on

the disc. For details,

refer to the guide

provided with your

disc.

SEL

DVD MENU

1 SUBTITLE

2 AUDIO

3 ANGLE

RETURN

PAGE

: forward

: backward

≥ The images change each time the

button is pressed.

To skip to a specific image:

Note:

≥ Some discs restrict scanning forward or

backward through still images.

RETURN

Press

RETURN

Press

AUDIO : 01

AUDIO : 02

AUDIO : 01

AUDIO : 02

Press

321

4 5 6

7 8 9

Press

321

4 5 6

7 8 9

CQ DVR909N CQ DVR909N

44 45

DVD Audio

•

Video/Video CD/CD Basics

(continued)

/ R

MUTE

SUB TITLE

ANGLE

REPEAT

STOP

PAUSE

PLAY

BAND

ST/MONO

TITLE /

CHAPTER

TRACK

VOLUME

TITLE

RETURN

CAR DVD PLAYER

DISP

GRP

Slow Playback

Switching the Subtitle Language

1 (During playback)

PAUSE

≥ “PAUSE” is displayed.

≥ “SLOW PLAY” is displayed.

≥ Playback is at approximately 1/3 normal speed.

To pause:

To resume normal playback:

Note:

≥ Reverse slow playback is not possible.

PAUSE

PLAY

BAND

(During playback)

SUB TITLE

≥ Initially, the subtitle

language is the language

that is set in the initial

settings. (If this language

has not been recorded, the

language that is displayed is

determined by the disc.)

Notes:

≥ The number of subtitle languages

depends on the disc.

≥ If no subtitles are recorded on the disc,

“/” lights.

≥ It may not be possible to switch the

subtitles unless the unit is at the DVD

menu (➡ page 43) or is at the initial

settings (➡ page 46).

≥ There may be a brief delay before the

subtitles appear.

Press

Hold

(0.5 second)

Press

(maximum: 32)

SUBTITLE OFF

SUBTITLE : 01

SUBTITLE : 02

"#%$, SEL

(SELECT)

9 (Slow Play)

MENU • TITLE

PLAY 1

PAUSE ;

ST/MONO

(STEREO/MONAURAL)

ANGLE

SUB TITLE

Switching the Angle

Title Menu

Switching between Stereo and Monaural

(During playback)

ANGLE

Note:

≥ If multiple angles are not

recorded on the disc, “/”

lights.

1 (During playback)

TITLE

≥ “PLAY” is displayed and the title menu appears on the

screen.

(Pressing this button again causes playback to start at

the scene from which the title menu was called.)

Example)

(Select item) (Finalize selection)

TITLE MENU

Castles

Woods

Rivers

Lovers

SEL

≥ When either “L/R CH L” or “L/R CH R” is selected,

the left or right channel audio is output on both the

left and right speakers.

(stereo)

(left channel)

(right channel)

Press

Hold

(2 seconds)

(maximum: 9)

ANGLE : 01

ANGLE : 02

ST/MONO

Hold

(2 seconds)

L/R CH ST

L/R CH L

L/R CH R

CQ DVR909N CQ DVR909N

46 47

DVD Audio

•

Video/Video CD/CD Basics

(continued)

(Changing the Initial Settings)

/ R

MUTE

SUB TITLE

ANGLE

REPEAT

STOP

PAUSE

PLAY

BAND

ST/MONO

TITLE /

CHAPTER

VOLUME

TITLE

RETURN

CAR DVD PLAYER

DISP

GRP

Menu language

Subtitle language

Select the setting

(While stopped)

Make the setting

In other cases (MENU LAN,

SUBTITLE LAN, AUDIO LAN)

≥ “CODE : ````” is displayed.

Input the four digit language code.

(➡ page 77)

Finalize selection.

To input the number again:

TITLE

321

4 5 6

7 8 9

SEL

RETURN

Notes:

≥ If [DISP] is pressed, the unit returns to regular

mode. (The setting is ignored.)

≥ If the language that was set is not recorded on

the disc, the language determined by the disc

is selected.

MENU LAN

SUBTITLE LAN

MENU LAN1 : en

1: English 3: Spanish 5: Italian

2: French 4: German 6: Other (➡ page 46)

(No subtitles)

Audio language

AUDIO LAN1 : en

TV aspect ratio

TV connection setting

This setting prevents playback from being stopped by the menu screen if a

monitor is not connected.

TV SELECT

TV ASPECT

YES

The TV image is displayed. (Select this setting when a monitor is connected.)

NONE

No TV image is displayed. (Select this setting when no monitor is connected.)

TV picture mode (4 : 3)

Set this when playing wide-screen video on a conventional-size (4 : 3) TV.

PAN & SCAN

Plays wide-screen video in Pan & Scan mode (in which the left and right

edges of the screen are cut off).

LETTER BOX

Plays wide-screen video in letterbox mode (in which black bands appear at

the top and bottom of the screen).

16 : 9

Use this setting when a wide-screen TV is connected.

≥ Wide-screen video can be played on the full screen.

4 : 3

Use this setting when a conventional TV is connected.

TV MODE (4:3)

Note:

≥ If “PAN & SCAN” or “LETTER BOX” is already set in the software, this setting is ignored.

1 2

Return to the regular mode

Press

TITLE

Hold (2 seconds)

(➡Next page)

(Regular mode)

(➡Next page)

Press

TV MODE(4:3)

TV ASPECT

TV SELECT

AUDIO LAN

SUBTITLE LAN

MENU LAN

AUDIO 01-02

Press

"#, SEL

(SELECT)

DISP

(DISPLAY)

RETURN

Number

Buttons

SUBT LAN1 : en

SUBT LAN : OFF

(LAN: LANGUAGE)

≥ The setting is completed and the disc will start

over from the beginning.

1 to 6

1: English 3: Spanish 5: Italian

2: French 4: German 6: Other (➡ page 46)

1 to 6

1: English 3: Spanish 5: Italian

2: French 4: German 6: Other (➡ page 46)

AUDIO LAN

1 to 6

CQ DVR909N CQ DVR909N

48 49

CD Changer Basics

/ R

MUTE

SUB TITLE

ANGLE

REPEAT

STO

PAUSE

PLAY

BAND

ST/MONO

TITL

LUME

TITLE

RETURN

DISP

GRP

Select

“CHANGER”

≥ A disc is played back.

If “NO DISC” is displayed:

Load a disc in the changer

(magazine).

Select the disc

(next disc)

(previous disc)

Select the track

(jump to the beginning of the

next track)

(jump to the beginning of the

current track, and then to

previous tracks)

Fast Forward/Fast Backward:

(Backward) (Forward)

REP

RAND

MAIN

Disc

Number

Elapsed

Playback Time

Track

Number

Lights when a magazine is

loaded in the changer.

When using twin changers, the number

corresponding to the selected changer lights.

Lights/blinks during

repeat playback.

Lights/blinks during random playback.

•

CLOCK

DISP

Changing the Display

Normal display

Clock display CD disc title display

Display off

CD track title display

(track number/

disc number/

elapsed playback time)

Notes:

≥ When playing an CD in which no title information has been recorded, the message “NO TITLE” is

displayed.

≥ When a title is displayed, the characters can be made to scroll across continuously or to stop.

(➡ page 57)

Connect a CD changer (CX-DP9061EN, etc.; sold separately).

1 2 3

SOURCE

POWER

DISC

P•SET

TUNE

TRACK

POWER

SOURCE

Press

Hold

PLAY 1

REPEAT

RANDOM

SCAN

DISP

(DISPLAY)

When using the main unit

Notes:

When you insert a magazine into the changer

≥ While the unit is turned off, the unit turns

on and enters CHANGER mode. (When a

magazine is pulled out, the unit turns off.)

≥ While another sound source is selected,

the unit switches to CHANGER mode.

Indicates pressing a button.

Indicates pressing a button

for an extended period of time.

Track Scan

Plays approximately 10 seconds of each of the

tracks on the discs in the changer in sequence.

Scan Play

Selecting tracks from all discs

A track selected at random from among all of

the discs in the changer is played back.

Random Play

Repeating a track

The track currently being played is repeated.

Repeat Playback

Using Two Changers (Dual changers)

Disc Scan

Plays approximately 10 seconds of the first track

on each of the discs in the changer in sequence.

Selecting tracks from one disc

A track selected at random from the current

disc being played is played back.

Repeating a disc

The disc currently being played is repeated.

≥ The elapsed playback time

display begins to blink.

≥ Once a complete cycle

through all the tracks on

the discs in the changer

has been completed, the

unit begins playing from

the start of the first track.

≥ The disc number display begins

to blink.

≥ Once a complete cycle through

all the discs in the changer has

been completed, the unit begins

playing from the start of the

first disc.

SCAN

To cancel:

To cancel: To cancel:

To cancel:

≥ “REP” lights.

≥ “RAND” lights. ≥ “RAND” blinks.

≥ “REP” blinks.

REPEAT

RANDOM

Use the dual changer control unit

(CA-CD55EN; sold separately) to connect the

2 CD changers to this unit. (➡ page 70)

PLAY

BAND

≥ The selected changer number (either 1 or 2)

lights.

Caution:

≥ If only one changer is connected to the dual

changer control unit, connect that changer to

the CHANGER 1 jacks.

Press

Hold

(2 seconds)

Hold

(2 seconds)

Hold

(2 seconds)

Hold

(2 seconds)

CHANGER 1

CHANGER 2

Hold

(2 seconds)

Hold (2 seconds)

(When connecting CX-DP9061EN only.)

Panasonic CQDVR909N Operating instructions

Brand: Panasonic

Model: CQDVR909N

Category: CD players

Type: Operating instructions

Download PDF

report

Panasonic CQDVR909N Operating instructions

Panasonic CQDVR909N Operating instructions

Related papers

Other documents