Version 1.1 Owner’s Manual Addendum
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
This document describes the features that have been added in this update.
In order to fully understand the M-380’s new features, please read this document together with the Owner’s Manual for the M-380.
M-380_v11Added_e.book 1 ページ ２０１０年１月２８日 木曜日 午前８時５２分
2
Functionality added in version 1.10
Functionality added in version 1.10
●
Connection to the S-400M and S-0808 is supported.(
☞
p. 4)
.
•
A feature for making the input/output settings on the S-4000M has been added.
The M-380 does not support REAC EMBEDDED POWER. When you connect an S-0808, install an external battery on the S-0808 to power it via the DC IN
port. Note, however, that when the connection to the M-380 is made via an S-4000M or S-4000D, the S-0808 is powered by the S-4000M or S-4000D,
and so no external battery is required.
●
Channel mute options have been added (
☞
p. 10).
•
You can select whether to mute AUX sends and DIRECT OUTs when input channels are muted.
●
Indicators for the REAC A and B ports have been added at the top display area.
fig.REACStatus_Guide.eps
.
●
New functionality has been added to the user buttons.
●
Other Added Functionality
●
The port names in the top display area flash when no input has been assigned to the channel.
•
When “NO ASSIGN” is flashing, no input
i
s assigned to the channel.
fig.NoAssign.eps
•
When a port name such as “A: IN 1” is displayed, either the input/output unit at the corresponding REAC port is not connected correctly, or a
nonexistent input is assigned to the channel
fig.AIN1.eps
DD
DD
ii
ii
ss
ss
pp
pp
ll
ll
aa
aa
yy
yy
Description
Unlighted
No REAC device connected
Flashing Establishing connection with REAC device
Lighted Normal connection with REAC device
FUNCTION
PARAM1 PARAM2 Button Explanation
EFFECT
EDIT GEQ
FX1
GEQ A
Lit when the specified screen is
displayed.
When FX1 through 4 are used as Dual GEQ, you access the
screen for each GEQ individually.
This is effective only for the FX using Dual GEQ.
FX1
GEQ B
FX2
GEQ A
FX2
GEQ B
FX3
GEQ A
FX3
GEQ B
FX4
GEQ A
FX4
GEQ B
M-380_v11Added_e.book 2 ページ ２０１０年１月２８日 木曜日 午前８時５２分
3
Functionality added in version 1.10
Functionality added in version 1.10
●
Display of the insert destination has been added to the GEQ EDIT and FX EDIT popups (Dual GEQ).
fig.GEQ_Guide.eps
●
A delay time indicator has been added to the "SDE-3000 x2" effect type.
This flashes in time with the delay time.
fig.Sde3000_Guide.eps
●
The user interface of the LOAD/SAVE popup have been changed.
You can move the folder on the project file list, and you can save and load project files in any desired folder.
●
The message “Completed.” is displayed when initialization of mixer settings finishes.
This is displayed when you have initialized the mixer settings using the INITIALIZE popup (SYSTEM screen > [F1 (INIT)]).
●
The patch symbols on the PATCHBAY screen have been changed to arrows.
Input patchbay patches are shown by an icon , and output patchbay patches are shown by an icon .
This makes the direction of signal flow easier to understand.
●
You can store scenes via the RS-232C.
For more information, refer to “RS-232C Reference Version 1.4.”
●
The layer buttons that flashed in the USER layer mode now light up steadily.
M-380_v11Added_e.book 3 ページ ２０１０年１月２８日 木曜日 午前８時５２分
4
S-4000M’s Input/Output Settings
Editing the S-4000M’s Input/Output Settings
The S-4000M has a Merge patchbay and an Output patchbay (Output
patchbay supports S-0808 8x8 I/O UNITS only). You can edit the S-4000M’s
Merge/Output patchbays using S-4000 RCS to change input/output
assignments.
Merge Patchbay
This merges the inputs of the REAC slave units (connected to the
REAC ports 1–4 of the S-4000M) into the channels to the M-380’s
REAC port.
Output Patchbay
This assigns channels from the M-380 to the outputs of the S-0808
units ( REAC ports 1–4).
You cannot edit an S-4000M’s input/output settings when the S-
4000M is set to the THRU mode.
The S-4000M input/output setup is saved to internal memory. The S-
4000M configuration window loads and displays the setup from the
connected S-4000M.
You can save/load the S-4000M input and output setups to a USB memory
as a S-4000M Input/Output Setup file (p. 9).
S-4000M’s input/output setups cannot be saved as part of scene
memory.
To edit S-4000M’s Merge/Output patchbay, use the S-4000M
CONFIGURATION popup.
fig.S4M_Config_Guide.eps
Slave device display
This part displays the REAC Slave devices connected to REAC ports 1–
4 of the S-4000M.
S-4000M Merge Patchbay
This part displays how the Slave devices are being patched through
the M-380.
PORT4 OPTION
•
Split Merged Inputs button
Check this button to send the merged inputs being sent to the M-380
out to REAC port 4 as well (p. 8).
The function buttons perform the following operations.
Storing Input/Output Setups
S-4000M CONFIGURATION popup
[F1 (MERGE)]
Displays MERGE tab.
[F2 (OUTPUT)] Displays OUTPUT tab.
[F4 (LOAD/SAVE)] Access the S-4000M LOAD/SAVE popup.
[F5 (AUTO MAP)] Resets the S-4000M Input/Output setup.
[F8 (CLOSE)] Closes the popup
1
2
3
1
2
3
M-380_v11Added_e.book 4 ページ ２０１０年１月２８日 木曜日 午前８時５２分
5
S-4000M’s Input/Output Settings
1.
In the SETUP section, press [SYSTEM] to access the
SYSTEM screen.
fig.System.eps
2.
Press [F2 (REAC CONFIG)].
The REAC CONFIG popup will appear.
3.
Select the target REAC port by pressing [F2 (REAC A)] or
[F3 (REAC B)].
fig.ReacConfig_S4000M.eps
4.
Press [F5 (S-4000M CONFIG)].
fig.S4M_Config1.eps
The S-4000M CONFIGURATION popup will appear.
You can reset and optimize the merge/output patchbays according to the
devices physically connected to REAC ports 1–4.
This has the same function as [AUTO MAP SLAVE UNITS] button on
S-4000M’s front panel.
1.
Access the S-4000M CONFIGURATION popup.
fig.S4M_Config1.eps
2.
Press [F5 (AUTO MAP)].
A confirmation message will ask you to confirm the operation.
3.
Press [F8 (OK)] to reset the S-4000M Input/Output setups.
Pressing [F7 (CANCEL)] will cancel the operation.
Accessing the S-4000M CONFIGURATION
popup
Resetting S-4000M Input/Output Setups
(System Reset)
M-380_v11Added_e.book 5 ページ ２０１０年１月２８日 木曜日 午前８時５２分
6
S-4000M’s Input/Output Settings
Merge Patchbay Operations
1.
Acesss the S-4000M CONFIGURATION popup.
2.
Press [F1 (MERGE)] to access the MERGE tab.
fig.S4M_Config_IN_Guide.eps
Merge Patchbay
This part displays overall view of the S-4000M’s merge patchbay.
You can move the cursor to the Merge Patchbay and press [ENTER] to
access the S-4000M MERGE PATCHBAY popup.
3.
Move cursor to the Merge Patchbay and press [ENTER].
fig.S4000MInputPatchbay.eps
The S-4000M MERGE PATCHBAY popup will appear.
Current Assign indication
This indicates the physical input source that is patched to the
channel at the cursor location.
Device indication
This indicates the REAC slave device that is selected by the function
buttons [F1 (PORT1)]–[F4 (PORT4)].
Patchbay grid
This grid lets you make patchbay settings.
fig.ScrInPatGridGuide.eps
REAC Channel indication
This indicates the number of the REAC channels being sent to the M-
380.
Input indication
This indicates the input numbers of the REAC slave device and the
signal level s.
The color indicates the signal level as follows.:
Patch symbol
A patch symbol is shown where the currently patched REAC channel
and input intersect. To change the patching, move the cursor to the
location where the desired REAC channel and input intersect, and
press [ENTER].
Unavailable area
The number area is shown in gray for inputs that cannot be used with
the currently connected REAC slave device.
The function buttons perform the following operations.
4.
Press [F1 (PORT1)]–[F4 (PORT4)] to select the desired S-
4000M’s REAC port.
5.
Move the cursor to the intersection of the desired REAC
channel and input, and press [ENTER].
1.
As described in step 1–4 of “Merge Patchbay Operations
(p. 6)”, access the S-4000M MERGE PATCHBAY popup.
2.
Press [F6 (CLEAR)].
fig.S4M_PatchChgConf.eps
A confirmation message will ask you to confirm the operation.
3.
Press [F8 (CLEAR)] to clear all assignments associated
with the currently selected S-4000M’s REAC port.
Pressing [F7 (CANCEL)] will cancel the operation.
1
1
2 34
2
3
4
1 2
3 4
Color
Signal Level
Black
Below -48dB
Green Between -48dB and -18dB
Yellow Above -18dB
[F1 (PORT1)]–
[F4 (PORT4)]
Selects the S-4000M’s REAC port
[F6 (CLEAR)] Clear all assignments of currently selected
REAC port.
[F8 (CLOSE)] Closes the popup
Clearing all assignments
1
2
3
4
M-380_v11Added_e.book 6 ページ ２０１０年１月２８日 木曜日 午前８時５２分
7
S-4000M’s Input/Output Settings
Output Patchbay Operations (S-0808)
1.
Access the S-4000M CONFIGURATION popup.
2.
Press [F2 (OUTPUT)] to access the OUTPUT tab.
fig.S4M_Config_OUT_Guide.eps
Output Patchbay
This part displays overall view of the S-4000M’s output patchbay.
You can move the cursor to the Output Patchbay and press [ENTER]
to access the S-4000M OUTPUT PATCHBAY popup.
3.
Move cursor to the desired Output Patchbay and press
[ENTER].
fig.S4000MIOutputPatchbay.eps
The S-4000M OUTPUT PATCHBAY popup will appear.
Current Assign indication
This indicates the channel that is patched to the physical output at
the cursor location.
Device indication
This indicates the REAC slave device that is that is the target of the S-
4000M OUTPUT pATCHBAY popup.
Patchbay grid
This grid lets you make patchbay settings.
fig.ScrOutPatGridGuide.eps
REAC Channel indication
This indicates the number and the signal level of the REAC channels
being sent from the M-380.
The color indicates the signal level as follows.:
Output indication
This indicates the output numbers of the REAC slave device.
Patch symbol
A patch symbol is shown where the currently patched REAC channel
and output intersect. To change the patching, move the cursor to the
location where the desired REAC channel and output intersect, and
press [ENTER].
Unavailable area
The number area is shown in gray for outputs that cannot be used
with the currently connected REAC slave device.
The function buttons perform the following operations.
4.
Move the cursor to the intersection of the desired REAC
channel and output, and press [ENTER].
1.
As described in step 1–3 of “Output Patchbay Operations
(S-0808) (p. 7)”, access the S-4000M OUTPUT PATCHBAY
popup.
2.
Press [F6 (CLEAR)].
fig.S4M_PatchChgConf.eps
A confirmation message will ask you to confirm the operation.
3.
Press [F8 (CLEAR)] to clear all assignments associated
with the currently selected S-4000M’s REAC port.
Pressing [F7 (CANCEL)] will cancel the operation.
1
1
2 34
2
3
4
1
2
3
4
Color
Signal Level
Black
Below -48dB
Green Between -48dB and -18dB
Yellow Between -18dB and 0dB
Red Above 0dB
[F6 (CLEAR)]
Clear all assignments.
[F8 (CLOSE)] Closes the popup
Clearing all assignments
1
2
3
4
M-380_v11Added_e.book 7 ページ ２０１０年１月２８日 木曜日 午前８時５２分
8
S-4000M’s Input/Output Settings
Splitting Merged Inputs (S-4000M's Split Function)
By using the S-4000M’s Split Function, you can split the merged inputs
(being sent to the M-380) to REAC port 4 of the S-4000M. It is very
convenient when splitting to a monitor console or a multi-channel
recording system.
fig.S4000MSplit.eps
When a REAC splitter (like the S-4000D) is connected to the S-
4000M’s REAC port A, the signal from the M-380 is split.
Notes About the S-4000M’s Split Function
* You can connect a REAC slave device to S-4000M’s REAC port 4
via a REAC splitter (like the S-4000D). In this case, the physical
inputs of the REAC slave device operate normally but all merged
inputs being sent to the M-380 will being sent out from the
physical outputs.
* If an M-48 is connected to the S-4000M’s REAC port 4, it is not
possible to manage/setup the M-48 from the M-380.
Using the S-4000M's split function makes it unnecessary to use the
M-380's output to REAC for stage-input splitting or recording.
1.
Access the S-4000M CONFIGURATION popup.
fig.S4M_Config1.eps
If the “Split Inputs to PORT4” button in the PORT4 OPTION is
checked, then the S-4000M’s split function is already turned on. The
following steps will not be necessary.
2.
Disconnect the REAC cable connected to REAC port 4 on
the S-4000M.
3.
Move cursor to the Split Merged Inputs button in the
PORT4 OPTION, and press [ENTER].
fig.S4M_SplitChgConf.eps
A confirmation message will ask you to confirm the operation.
4.
Press [F8 (OK)] to enable the S-4000M’s split function.
Pressing [F7 (CANCEL)] will cancel the operation.
fig.S4M_Config_Split.eps
fig.S4M_Config_Split_Out.eps
5.
Connect the REAC cable to REAC port 4 on the S-4000M.
REAC A or REAC B
MASTER
S-0808
S-4000M
SLAVE
1 1 1 1
SPLITSLAVE
S-4000S
(32-channel output)
PC Recording
S-4000D
2 3
A
1
4
Merged Inputs
Merged Inputs
(Split)
Using S-4000M’s split function
M-380_v11Added_e.book 8 ページ ２０１０年１月２８日 木曜日 午前８時５２分
9
S-4000M’s Input/Output Settings
Save/Load the S-4000M’s Input/Output Setups
You can save/load the S-4000M input and output setups to a USB memory
as a S-4000M Input/Output Setup file .
To save/load the S-4000M Input/Output Setup File, use the S-4000M
LOAD/SAVE popup.
1.
Access the S-4000M CONFIGURATION popup.
fig.S4M_Config1.eps
2.
Press [F4 (LOAD/SAVE)].
fig.S4M_LoadSave_Guide.eps
The S-4000M LOAD/SAVE popup will appear.
File list
This lists the S-4000M Input/Output Setup files that have been saved
to USB memory. You can specify the save-destination folder for the
file, or specify the file that you want to load.
The function buttons perform the following operations.
1.
Access the S-4000M LOAD/SAVE popup.
2.
Press [F2 (SAVE)].
fig.S4M_Save.eps
The S-4000M SAVE popup will appear.
3.
Edit the name of the S-4000M Input/Output Setup file in
the name edit field.
4.
When you press [F8 (SAVE)], a message indicating the
status of the save procedure will appear. When saving is
completed, the message will close.
Pressing [F7 (CANCEL)] will cancel the operation.
Do not disconnect the USB memory or switch off the M-380’s power
while data is being saved to USB memory. Doing so may destroy the
data saved in USB memory.
1.
Access the S-4000M LOAD/SAVE popup.
2.
In the file list, select the S-4000 Input/Output Setup file
that you want to load.
3.
Press [F1 (LOAD)].
fig.S4M_LoadConf.eps
A confirmation message will ask you to confirm the operation.
4.
When you press [F8 (LOAD)], a message indicating the
status of the load procedure will appear. When loading is
completed, the message will close.
Pressing [F7 (CANCEL)] will cancel the operation.
Do not disconnect the USB memory or switch off the M-380’s power
while data is being saved to USB memory. Doing so may destroy the
data saved in USB memory.
Accessing the S-4000M LOAD/SAVE
popup
[F1 (LOAD)]
Loads the S-4000M Input/Output Setup file
selected in the file list.
[F2 (SAVE)] Saves the S-4000M’s input/output setups.
[F3 (MAKE FOLDER)] Creates a folder in the file list.
[F4 (NAME EDIT)] Accesses the NAME EDIT popup where
you can edit the name of the file or folder.
[F5 (DELETE)] Deletes the selected file or folder from the
file list.
[F8 (CLOSE)] Closes the popup
1
1
Saving the S-4000M Input/Output Setup
file
Loading the S-4000M Input/Output
Setup file
M-380_v11Added_e.book 9 ページ ２０１０年１月２８日 木曜日 午前８時５２分
10
New Functionality for the Input Channels
A channel mute option has been added.
You can select whether to mute out AUX SENDs and DIRECT OUTs when muting CH1–48.
Sends from POST FADER are always muted by the channel muting, regardless of the channel mute option settings.
New Functionality for the Input Channels
PRE EQ PRE FADER POST FADER
MUTE FADER
CH 1–48
4BAND
EQ
PA N
PRE EQ
SW SEND
SOLO
PRE EQ
AFL(R)
PFL(R)
AFL(L)
PFL(L)
SW SEND
AFL SW
PRE EQ
AUX SEND 1–16
PRE FADER
POST FADER
PA N
PRE FADER
POST FADER
PRE FADER
POST FADER
TO MAIRIX 1–8,
TO OUTPUT PATCHBAY
AUX
LINK
DIRECT OUT
POINT
MUTE
MUTE
1.
Press [SYSTEM] to access the SYSTEM screen.
fig.System.eps
CH-MUTE OPTION selection buttons
These buttons make the settings for the channel mute options.
•
Mutes AUX SENDS
If this is checked, muting input channel also mutes AUX SENDs.
•
Mutes DIRECT OUTS
If this is checked, muting input channel also mutes DIRECT OUTs.
2.
Use the CH-MUTE OPTION selection buttons to make the
settings for the channel mute options.
The settings you make here are applied to all input channels.
Setting the Channel Mute Options
1
1
1PS
M-380_v11Added_e.book 10 ページ ２０１０年１月２８日 木曜日 午前８時５２分
/