Troy-Bilt 13A879KS066 User manual

Brand: Troy-Bilt

Model: 13A879KS066

Category: Lawnmowers

Type: User manual

This manual is also suitable for

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

Printed In USA

Safe Operation Practices • Set-Up • Operation • Maintenance • Troubleshooting • Warranty

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS ENGINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

OperatOr’s Manual

Form No. 769-09649A

(September 25, 2015)

547 cc OHV Vertical Shaft Engine

This Operator’s Manual is an important part of your new engine. It will help you prepare and maintain the engine for the best

performance. Please read and understand the contents before operating the engine.

Thank You

Model NuMber

Serial NuMber

Customer Support

Please do NOT return the machine to the retailer or dealer without first contacting the Customer Support Department.

If you have difficulty assembling this product, have questions regarding the controls, operation, or maintenance of this machine, want

to order replacement parts/attachments/accessories, or want to view an online How-To video; you can seek help from the experts. Have

your full model number and serial number ready. Choose from the options below:

◊ Web: www.mtdproducts.com/equipment/mtdproducts

◊ Phone: (800) 800-7310

◊ Mail: MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019

To The Owner

Table of Contents

Important Safe Operation Practices ..................... 3

Safety Labels............................................................ 5

Set-Up ....................................................................... 6

Controls & Features ................................................. 8

Operation ................................................................. 9

Maintenance & Adjustments .................................10

Troubleshooting .....................................................16

Replacement Parts .................................................17

Spanish ....................................................................21

Record Product Information

Before operating your new engine, please locate the model plate on the engine (shaded area in Figure below) and record the

information in the provided area below. This information will be necessary, should you seek technical support via our web site or with

your local dealer.

Important Safe Operation Practices

WARNING! This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow

all instructions in this manual before attempting to operate the equipment. Failure to

comply with these instructions may result in personal injury. When you see this symbol.

HEED ITS WARNING!

DANGER! This machine was built to be operated according to the safe operation practices

in this manual. As with any type of power equipment, carelessness or error on the part of the

operator can result in serious injury. This machine is capable of amputating fingers, hands,

toes and feet and throwing foreign objects. Failure to observe the following safety

instructions could result in serious injury or death.

CALIFORNIA PROPOSITION 65

WARNING! Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to State of California to cause cancer and birth defects

or other reproductive harm.

Training

1. Read, understand and follow all instructions on the engine

and in the manual(s) before attempting to assemble and

operate. Keep this manual in a safe place for future and

regular reference and for ordering replacement parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the engine and disengage them quickly.

3. Never allow children under 14 years of age to operate the

engine. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and be trained and supervised by an adult.

4. Never allow adults to operate the machine without proper

instruction.

5. Keep the area of operation clear of all persons, particularly

small children and pets. Stop machine if anyone enters the

area.

Preparation

1. Thoroughly inspect the area where the equipment is to

be used. Remove all stones, sticks, wire and other foreign

objects which could be tripped over and cause personal

injury.

2. Wear sturdy, rough-soled work shoes and close fitting

slacks and shirts. Loose fitting clothes or jewelry can be

caught in the moving parts. Never operate the machine in

bare feet or sandals.

3. Disengage clutch levers and shift (if equipped) into neutral

(“N”) before starting the engine.

4. Never leave the engine running while unattended.

5. Never attempt to make any adjustments while the engine

is running, except where specifically recommended in the

operator’s manual.

Safe Handling of Gasoline:

To avoid personal injury or property damage, use extreme care

in handling gasoline. Gasoline is extremely flammable and the

vapors are explosive. Serious personal injury can occur when

gasoline is spilled on yourself and/or your clothes which can

ignite. Wash your skin and change clothes immediately.

1. When adding fuel, turn engine OFF and let engine cool at

least 2 minutes before removing the gas cap.

2. Fill fuel tank outdoors or in well ventilated area.

3. Use only an approved gasoline container.

4. Never fill containers inside a vehicle or on a truck or trailer

bed with a plastic liner. Always place containers on the

ground away from your vehicle before filling.

5. If possible, remove gas-powered equipment from the truck

or trailer and refuel it on the ground. If this is not possible,

then refuel such equipment on a trailer with a portable

container, rather than from a gasoline dispenser nozzle.

6. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

4 Section 2 — important Safe operation practiceS

7. Do not overfill fuel tank. Fill tank to full as indicated by the

fuel level indicator installed inside of the fuel tank. Do not

over-fill to allow space for fuel expansion. On some models,

a fuel level indicator may NOT be present, in this instance,

fill the tank no more than 1/2 inch below the bottom of the

filler neck to allow space for fuel expansion.

8. Replace fuel cap and tighten until the cap ratchets.

9. If gasoline is spilled, wipe it off the engine and the

equipment. Move the machine to another area. Wait five

minutes before starting the engine.

10. To reduce fire hazards, keep the machine free of grass ,

leaves or other debris build up. Clean up oil or fuel spillage

and remove any fuel-soaked debris.

11. Keep gasoline away from sparks, open flames, pilot lights,

heat, and other ignition sources.

12. Never fuel equipment indoors because flammable vapors

will accumulate in the area.

13. Extinguish all cigarettes, cigars, pipes, and other sources of

ignition.

14. Check fuel line, tank, cap, and fittings frequently for cracks

or leaks. Replace if necessary.

Operation

1. When starting the engine, make sure spark plug, muffler,

and fuel cap are in place.

2. Do not crank engine with spark plug removed.

3. If fuel spills, wait until it evaporates before starting engine.

4. Allow muffler, engine cylinder, and fins to cool before

touching.

5. Keep children away from hot or running engines. They can

suffer burns from a hot muffler.

6. Remove accumulated combustibles from muffler and

cylinder area.

7. Operate equipment with all guards in place.

8. Keep hands and feet away from rotating parts.

9. Tie up long hair and remove jewelry.

10. Do not wear loose-fitting clothing, dangling drawstrings or

items that could become caught.

11. When starting the engine, pull cord slowly until resistance

is felt, then pull rapidly (if not electric start).

12. Remove all external equipment/engine loads before

starting engine.

13. Direct coupled equipment components such as, but not

limited to blades, impellers, pulleys, sprockets, etc., must

be securely attached.

Maintenance & Storage

1. Keep the engine in safe working order

2. Allow the engine to cool at least five minutes before

storing. Never tamper with safety devices. Check their

proper operation regularly.

3. Check bolts and screws for proper tightness at frequent

intervals to keep the engine in safe working condition.

Visually inspect the engine for any damage.

4. Before cleaning, repairing or inspecting; stop the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire and ground it against the

engine to prevent unintended starting.

5. Do not change the engine governor settings or over-speed

the engine. The governor controls the maximum safe

operating speed of the engine.

6. Maintain and replace safety and instruction labels as

necessary.

7. Always refer to the operator’s manual for important details

if the machine is to be stored for an extended period of

time.

8. If the fuel tank has to be drained, do this outdoors.

9. Observe proper disposal laws and regulations for gas, oil,

etc. to protect the environment.

Do not modify engine

To avoid serious injury or death, do not modify engine in any

way. Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. Never tamper

with factory setting of engine governor.

Notice Regarding Emissions

Engines which are certified to comply with California and federal

EPA emission regulations for SORE (Small Off Road Equipment)

are certified to operate on regular unleaded gasoline, and

may include the following emission control systems: Engine

Modification (EM), Oxidizing Catalyst (OC), Secondary Air

Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING! This machine is equipped with an

internal combustion engine and should not be used

on or near any unimproved forest-covered, brush

covered or grass-covered land unless the engine’s

exhaust system is equipped with a spark arrestor

meeting applicable local or state laws (if any).

If a spark arrestor is used, it should be maintained in effective

working order by the operator. In the State of California the

above is required by law (Section 4442 of the California Public

Resources Code). Other states may have similar laws. Federal laws

apply on federal lands.

A spark arrestor for the muffler is available through your

nearest engine authorized service dealer or contact the service

department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

5Section 2 — important Safe operation practiceS

WARNING! Your Responsibility — Restrict the use of this power machine to persons who read, understand and

follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

Safety Symbols

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the

machine before attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to

assemble and operate.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon

monoxide, an odorless and deadly gas.

WARNING— ELECTRICAL SHOCK

Do not use the engine’s electric starter in the rain.

WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during operation. Allow engine

and muffler to cool before touching.

Set-Up

Gas & Oil

NOTE: The engine is shipped without gasoline and with motor

oil in the engine. However, you MUST check the oil level before

operating. Be careful not to overfill. Running the engine with

insufficient oil can cause serious engine damage and void the

engine warranty.

WARNING! Always keep hands and feet clear of

equipment moving parts. Do not use a pressurized

starting fluid. Vapors are flammable.

Oil Recommendations

Before starting engine, check oil level, capacity is 1800 ml/57.5 fl.

oz. Refer to viscosity chart in Figure 3-1 for oil recommendations.

Do not over-fill. Use a 4-stroke, or an equivalent high detergent,

premium quality motor oil certified to meet or exceed

U.S. automobile manufacturer’s requirements for service

classification of a minimum level SJ (higher letter ratings are

acceptable such as SL and SM grades). Motor oil will display this

designation on the container.

SAE 10W-30 is recommended for general, all temperature use. If

single viscosity oil is used, select the appropriate viscosity for the

average temperature in your area from the chart below.

-30º -20º -10º 0º

0º 15º 30º 50º 70º 85º 105º

10º 20º 30º 40º

-20º

(ºC)

(ºF)

5W-30

10W-30

Synthetic 5W-30

Figure 3-1

CAUTION: Do not use non-detergent oil or 2-stroke engine oil. It

could shorten the engine’s service life.

NOTE: A 5w30 synthetic oil may be used to improve start ability

for cold weather (temperatures below 40 F).

Checking Oil Level

NOTE: Be sure to check the oil while on a level surface with the

engine stopped.

1. Remove the oil filler cap/dipstick and wipe the dipstick

clean.

2. Insert the dipstick into the oil filler neck. Turn the dipstick

a 1/4 turn into the locked position to fully seat. See Figure

3-2.

Upper

Level

Figure 3-2

3. Remove dipstick to check the oil level.

4. If the level is low, slowly add oil to the upper limit on the

dipstick. See Figure 3-2 inset.

5. Reinsert the dipstick and turn to the locked position before

starting the engine.

NOTE: Do not overfill. Overfilling with oil may cause

smoking, hard starting, spark plug fouling, hydraulic lock,

or oil saturation of air cleaner.

7Section 3 — Set-Up

Fuel Requirements

CAUTION: Operating the engine with E15 or E85

fuel, an oil/gasoline mixture, dirty gasoline, or

gasoline over 30 days old without fuel stabilizing

additive may result in damage to your engine’s

carburetor. Subsequent damage would not be

covered under the manufacturer’s warranty.

Use automotive gasoline (unleaded or low leaded to minimize

combustion chamber deposits) with a minimum of 87 octane.

Gasoline with up to 10% ethanol (E10) or 15% MTBE (Methyl

Tertiary Butyl Ether) can be used. Never use an oil/gasoline

mixture or dirty gasoline. Avoid getting dirt, dust, or water in the

fuel tank. DO NOT use E15 or E85 gasoline.

WARNING! Gasoline is extremely flammable and is

explosive under certain conditions.

• Refuel in a well-ventilated area with the engine stopped.

Do not smoke or allow flames or sparks in the area where

the engine is refueled or where gasoline is stored.

• Do not overfill the fuel tank. After refueling, make sure the

tank cap is closed properly and securely.

• Be careful not to spill fuel when refueling. Spilled fuel or

fuel vapor may ignite. If any fuel is spilled, make sure the

area is dry before starting the engine.

• Avoid repeated or prolonged contact with skin or

breathing of vapor.

Adding Fuel

WARNING! An adult should fuel this engine.

NEVER allow children to refuel the engine. Gasoline

(fuel) vapors are highly flammable and can explode.

Fuel vapors can spread and be ignited by a spark or

flame many feet away from engine. To prevent injury

or death from fuel fires, follow these instructions:

• DO NOT use leaded fuel.

• Fuel must be fresh and clean. NEVER use fuel left over

from last season or stored for long periods.

• NEVER mix oil with fuel in this engine.

• DO NOT use fuel containing Methanol (Wood

Alcohol)

NOTE: Before refueling, allow engine to cool two minutes.

1. Clean around fuel fill before removing cap to fuel.

2. Fill tank until fuel reaches ⁄ inch below the bottom of the

filler neck to allow space for fuel expansion. Be careful not

to overfill.

3. Replace the fuel cap and tighten securely. Wipe up spilled

fuel before starting engine. If fuel is spilled DO NOT start

engine. Move machine away from area of spillage. Avoid

creating any source of ignition until fuel vapors are gone.

Controls and Features

Throttle/Choke Control

The throttle/choke control is located on the mower and is used to

aid in starting/stopping the engine and adjusting engine speeds.

Refer to the Controls and Features section of the mower manual

for more information regarding this control.

Oil Drain

Removing the oil drain plug will drain the oil from the engine.

The engine is equipped with a side drain.

Oil Fill Cap

Remove the oil fill cap to check the oil level and add oil.

Fuel Cap

Remove the fuel cap to add fuel. Refer to the Controls and

Features section of the lawn mower’s manual for the location of

the fuel cap.

Finger Guard

Oil Drain

Carburetor

Fuel Filter

Electric

Starter

Oil Filter

Spark Plug

Air Cleaner

Oil Fill Cap

Figure 4-1

Operation

Pre-Operation Check

The engine is shipped without gasoline and with oil in the

engine. See the Set-Up Section of this manual for instructions on

adding gasoline and checking oil.

Starting the Engine

1. Release all controls on the mower.

2. Move the gear shift lever into the neutral (N) position.

3. If starting a cold engine, place the

throttle/choke control all the way

forward, into the CHOKE position.

Note: Use of choke may not be

necessary if the engine is warm or

the air temperature is high.

4. Insert the key into the ignition

switch.

5. Turn the ignition key clockwise

to the START position. After the

engine starts, release the key. It

will return to the RUN position.

See Figure 5-1.

CAUTION: Do NOT hold the key in the START

position for longer than five seconds at a time.

Doing so may cause damage to your engine’s

electric starter.

6. Move the throttle/choke control into the FAST (rabbit)

position.

NOTE: Never leave the throttle/choke control in the CHOKE

while operating the mower. Doing so will result in a “rich”

fuel mixture and cause the engine to run poorly.

Stop

Position

Start

Position

Run

Position

Figure 5-1

Stopping the Engine

WARNING! If you strike a foreign object, stop the

engine and remove the ignition key (if so equipped).

Thoroughly inspect the machine for any damage.

Repair the damage before restarting and operating.

1. If the blades are engaged, disengage the PTO.

2. Turn the ignition key counterclockwise to the STOP

position.

3. Remove the key from the ignition switch to prevent

unintended starting.

Fast

Slow

Choke

Engine Maintenance

WARNING: Shut off the engine before performing

any maintenance. To prevent accidental start-up,

disconnect the spark plug boot.

Periodic inspection and adjustment of the engine is essential if

high level performance is to be maintained. Regular maintenance

will also ensure a long service life. The required service intervals

and the kind of maintenance to be performed are described

in the table below. Follow the hourly or calendar intervals,

whichever occur first. More frequent service is required when

operating in adverse conditions.

WARNING: If the engine has been running, the

muffler will be very hot. Be careful not to touch the

muffler.

† Service more frequently when used in dusty areas.

†† Every season or 25 hours if operating under heavy load or high ambient temperature.

Maintenance Schedule

After First 5

Hours

Each use or

Every 5-10

Hrs.

Every Season

or 25 Hours

Every season

or 50 Hours

Every season

or 100 Hours

Service

Dates

Check Engine Oil Level

Change Engine Oil ††

P P

Change Engine Oil FIlter ††

Check Air Cleaner

Service Air Cleaner †

Check Spark Plug

Replace Spark Plug

Clean Cooling Fins

Replace Fuel Filter

Clean Finger Guard and around Muer

11Section 6 — Maintenance

Oil Service

• Check oil level regularly.

• Be sure correct oil level is maintained. Check every five

to ten hours before starting engine. See oil checking

procedure in the Set-Up section.

Oil Drain

IMPORTANT: Be sure to check engine on a level surface with the

engine stopped. Drain the oil while the engine is still warm to

assure rapid and complete draining.

1. Remove all fuel from tank by running engine until it stops

from lack of fuel.

2. Remove drain plug and allow oil to drain into a suitable

container. See Figure 6-1.

Oil Fill Cap

Drain

Plug

Figure 6-1

3. Reinstall the drain plug and tighten it securely, 12-14 Nm

(106.2-123.9 in-lb).

IMPORTANT: Used motor oil may cause skin cancer if repeatedly

left in contact with the skin for prolonged periods. Although this

is unlikely unless you handle used oil on a daily basis, it is still

advisable to thoroughly wash your hands with soap and water as

soon as possible after handling used oil.

NOTE: Please dispose of used motor oil in a manner that is

compatible with the environment. Check with your local

municipality for proper disposal procedure. Do not throw it in

the trash or pour it on the ground.

Replace Oil Filter

This engine is equipped with a spin-on oil filter that should be

replaced each time an oil change is performed, every season or

50 hours. Refer to Figure 6-2.

Oil Filter

Figure 6-2

1. Drain oil. See oil drain section.

2. Remove oil filter. Dispose of old oil filter properly.

3. Lube gasket of new oil filter with clean oil.

4. Install and turn oil filter by hand until the gasket comes in

contact with the sealing surface of the crankcase cover,

then tighten the oil filter, 10-12 Nm (88.5-106.2 in-lb), 1/2-

3/4 turn.

5. Add oil. See add oil section.

6. Make sure dipstick is installed.

7. Start and run engine. Check for leaks.

8. Stop engine. Wait a few minutes and check the oil level.

See checking oil level section.

9. Install and tighten dipstick.

12 Section 6 — Maintenance

1. Unscrew a 1/4 turn and remove the thumb screws.

2. Remove the air filter cover. See Figure 6-4.

Air Filter

Cover

Thumb

Screw

Figure 6-4

3. Pull up on an angle and then forward to remove the air

filter. See Figure 6-5.

Figure 6-5

Add Oil

IMPORTANT: Be sure to check engine on a level surface with the

engine stopped.

1. Wipe around dipstick cap and tube with a clean cloth to

remove any debris. See Figure 6-3.

Figure 6-3

2. Remove dipstick and wipe clean with a cloth.

3. Pour oil into the dipstick tube. Do not over fill. With an oil

filter change the high level amount of oil for this engine is

1700 ml (57.48 fl-oz.).

4. Install dipstick and turn to locked position before starting

engine.

5. Start engine. Allow to run for a few seconds and then shut

down the engine.

6. Check the oil level. See Checking Oil Level section.

Air Filter Service

Paper filters cannot be cleaned and should be replaced every

100 operating hours; more often if used in extremely dusty

conditions.

WARNING: Never use gasoline or low flash point

solvents for cleaning the air filter element. A fire or

explosion could result.

IMPORTANT: Never run the engine without the air filter. Rapid

engine wear will result.

13Section 6 — Maintenance

7. Attach the air filter cover. See Figure 6-8. Turn thumb

screws clockwise a 1/4 turn until snug. Check for any

misalignment.

Air Filter

Cover

Figure 6-8

Spark Plug Service

WARNING: DO NOT check for spark with spark

plug removed. DO NOT crank engine with spark

plug removed.

To ensure proper engine operation, the spark plug must be

properly gapped and free of deposits.

1. Remove the spark plug boot and use a spark plug wrench

to remove the plug. See Figure 6-9.

Spark Plug Boot

Figure 6-9

4. Remove the foam pre-filter from around the paper air

filter. See Figure 6-6. Replace paper element when dirty or

damaged. Clean foam element or replace when damaged.

NOTE: The foam element cannot be purchased separately.

Air filter is only sold as an assembly.

Air FIlter

Pre-Filter

Figure 6-6

5. To clean foam element, wash in a mild liquid detergent and

water. Squeeze or press the foam element to rinse out dirt

and water. Do not twist; this could damage or tear the foam

element. Allow to dry thoroughly before using. DO NOT oil

the foam element.

6. Attach the new air filter with foam element, aligning the

hole in the air filter with the intake manifold. See Figure 6-7.

Intake

Manifold

Figure 6-7

14 Section 6 — Maintenance

WARNING: If the engine has been running, the

muffler will be very hot. Be careful not to touch the

muffler.

2. Visually inspect the spark plug. Discard the spark plug

if there is apparent wear, or if the insulator is cracked or

chipped. Clean the spark plug with a wire brush if it is to be

reused.

3. Measure the plug gap with a feeler gauge. Correct as

necessary by bending electrode. See Figure 6-10. The gap

should be set to 0.024-0.031 in.

Electrode

0.024-0.031 in.

Figure 6-10

4. Check that the spark plug washer is in good condition

and thread the spark plug in by hand to prevent cross-

threading.

5. After the spark plug is seated, tighten with a spark plug

wrench to compress the washer.

NOTE: When installing a new spark plug, tighten 1/2 turn

after the spark plug seats to compress the washer. When

reinstalling a used spark plug, tighten 1/8-1/4 turn after the

spark plug seats to compress the washer.

IMPORTANT: The spark plug must be securely tightened.

An improperly tightened spark plug can become very hot

and may damage the engine.

Fuel Filter Service

The fuel filter cannot be cleaned and should be replaced every

100 operating hours; more often if run with old gasoline.

1. Remove all fuel from tank by running engine until it stops

from lack of fuel.

2. Use pliers to squeeze tabs on the clamps, then slide the

clamps away from the fuel filter. See Figure 6-11.

Fuel Filter

Fuel Line

Tab

Clamp

Figure 6-11

3. Twist and pull the fuel lines off of the fuel filter.

4. Replace with a new fuel filter.

5. Secure the fuel lines with the clamps.

15Section 6 — Maintenance

Clean Engine

If the engine has been running, allow it to cool for at least half

an hour before cleaning. Periodically remove dirt build-up from

engine. Clean cooling fins every 25 hours. Clean with a brush or

compressed air.

IMPORTANT: Do not spray engine with water to clean because

water could contaminate fuel. Using a garden hose or pressure

washing equipment can also force water into the air cleaner or

muffler opening. Water in the air cleaner will soak the paper

element, and water that passes through the element or muffler

can enter the cylinder, causing damage.

WARNING: Accumulation of debris around muffler

could cause a fire. Inspect and clean before every

use.

Storage

CAUTION: Failure to use a fuel stabilizing additive

or completely run the engine until it’s out of fuel

before off-season storage may result in damage to

your engine’s carburetor. Subsequent damage

would not be covered under the manufacturer’s

warranty.

Gasoline that will be stored longer than 30 days needs to be

pre-treated upon purchase with fuel stabilizer to prevent

gum and varnish from forming in the engines fuel and intake

system. Improper fuel storage can result in hard starting, no

starting, stalling and poor performance. If the gasoline in your

engine deteriorates during storage, you may need to have the

carburetor, and other fuel system components, serviced or

replaced.

1. Remove all fuel from tank by running engine until it stops

from lack of fuel.

WARNING: Never leave engine unattended while

running.

2. Change oil. See Oil Change section.

3. Remove spark plug and pour about 1/2 an ounce of engine

oil into cylinder. Replace spark plug and crank slowly to

distribute oil.

4. Clean debris from around engine, under finger guard, and

under, around and behind muffler. Touch up any damaged

paint, and coat other areas that may rust with a light film

of oil.

5. Store in a clean, dry and well ventilated area away from any

appliance that operates with a flame or pilot light, such

as a furnace, water heater, or clothes dryer. Also avoid any

area with a spark producing electric motor, or where power

tools are operated.

6. If possible, also avoid storage areas with high humidity,

because that promotes rust and corrosion.

7. Keep the engine level in storage. Tilting can cause fuel or

oil leakage.

Removing From Storage

1. Check your engine as described in the Pre-Operation Check

section of this manual. Check for debris under blower

housing.

2. If the fuel was drained during storage preparation, fill the

tank with fresh gasoline. If you keep a container of gasoline

for refueling, make certain it contains only fresh fuel.

Gasoline oxidizes and deteriorates over time, causing hard

starting.

3. If the cylinder was coated with oil during storage

preparation, the engine will smoke briefly at startup. This

is normal.

Troubleshooting

Problem Cause Remedy

Engine Fails to start 1. Choke not activated.

2. Spark plug boot disconnected.

3. Fuel tank empty or stale fuel.

4. Faulty spark plug.

5. Reduced fuel flow/Blocked fuel filter.

6. Engine flooded.

7. Dead battery.

8. Blown fuse.

1. Place throttle/choke control in CHOKE

position.

2. Connect wire to spark boot.

3. Fill tank with clean, fresh gasoline.

4. Clean, adjust gap, or replace.

5. Replace fuel filter as instructed in the

Maintenance section.

6. Crank engine with throttle in FAST position.

7. Recharge battery. See equipment operator’s

manual.

8. Replace blown fuse. See equipment

operator’s manual.

Engine runs erratic 1. Spark plug boot loose.

2. Reduced fuel flow/Blocked fuel filter.

3. Vent in gas cap plugged.

4. Water or dirt in fuel system.

5. Dirty air cleaner.

6. Engine running with CHOKE activated.

1. Connect and tighten spark plug boot.

2. Replace fuel filter as instructed in the

Maintenance section.

3. Clear vent.

4. Drain fuel tank. Refill with fresh fuel.

5. Replace air cleaner element and/or clean

pre-cleaner.

6. Move throttle/choke control out of CHOKE

position.

Engine overheats 1. Engine oil level low.

2. Air flow restricted.

1. Fill crankcase with proper oil.

2. Clean grass clippings and debris from around

the engine’s cooling fins and blower housing.

Occasional skips

(hesitates) at

high speed

1. Spark plug gap too close. 1. Remove spark plug and adjust gap.

Idles poorly 1. Spark plug fouled, faulty, or gap too wide.

2. Dirty air cleaner.

1. Reset gap or replace spark plug.

2. Replace air cleaner element and/or clean

pre-cleaner.

Replacement Parts

Phone (800) 800-7310 or (330) 220-4683 to order replacement parts or a complete Parts Manual (have your full model number and

serial number ready). Parts Manual downloads are also available free of charge at www.mtdproducts.com.

Component Part Number and Description

951-10292 Spark Plug

937-05066 Air Filter Assembly (Includes Pre-Filter)

951-3013 Fuel Filter

951-12690 Oil Filter

No tes

FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

MTD Consumer Group Inc, the United States Environmental Protection Agency (EPA), and for those products certified for sale in the state

of California, the California Air Resources Board (CARB) are pleased to explain the emission control system (ECS) warranty on your 2015-

2016 small off-road spark-ignited engine and equipment (outdoor equipment). In California, new outdoor equipment must be designed,

built and equipped to meet the State’s stringent anti-smog standards (in other states, outdoor equipment must be designed, built, and

equipped to meet the U.S. EPA small off-road spark ignition engine regulations). MTD Consumer Group Inc must warrant the ECS on your

outdoor equipment for the period of time listed below, provided there has been no abuse, neglect, or improper maintenance of the outdoor

equipment.

Your ECS may include parts such as the carburetor, fuel-injection system, ignition system, catalytic converter, fuel tanks, fuel lines, fuel caps,

valves, canisters, filters, vapor hoses, clamps, connectors, and other associated emission-related components.

Where a warrantable condition exists, MTD Consumer Group Inc will repair your outdoor equipment at no cost to you including diagnosis,

parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE:

This emission control system is warranted for two years. If any emission-related part on your outdoor equipment is defective, the part will be

repaired or replaced by MTD Consumer Group Inc.

OWNER’S WARRANTY RESPONSIBILITIES:

As the outdoor equipment owner, you are responsible for performance of the required maintenance listed in your owner’s manual. MTD

Consumer Group Inc recommends that you retain all receipts covering maintenance on your outdoor equipment, but MTD Consumer Group Inc

cannot deny warranty solely for the lack of receipts.

As the outdoor equipment owner, you should however be aware that MTD Consumer Group Inc may deny you warranty coverage if your

outdoor equipment or a part has failed due to abuse, neglect, improper maintenance, or unapproved modifications.

You are responsible for presenting your outdoor equipment to MTD Consumer Group Inc’s distribution center or service center as soon as

the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question

regarding your warranty coverage, you should contact the MTD Consumer Group Inc Service Department at 1-800-800-7310 or at

http://support.mtdproducts.com.

GENERAL EMISSIONS WARRANTY COVERAGE:

MTD Consumer Group Inc warrants to the ultimate purchaser and each subsequent purchaser that the outdoor equipment is: (1) designed,

built, and equipped so as to conform with all applicable regulations; and (2) free from defects in materials and workmanship that cause the

failure of a warranted part for a period of two years.

The warranty period begins on the date the outdoor equipment is delivered to an ultimate purchaser or first placed into service.

Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:

1. Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied is warranted for

the warranty period stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by MTD

Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the

remainder of the period.

2. Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period

stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.

3. Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the

period of time before the first scheduled replacement date for that part. If the part fails before the first scheduled replacement, the part

will be repaired or replaced by MTD Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under

warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part.

4. Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge

to the owner.

5. Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to

service the subject engines or equipment.

6. The outdoor equipment owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective, emission-

related warranted part, provided that such diagnostic work is performed at a warranty station.

7. MTD Consumer Group Inc is liable for damages to other engine or equipment components proximately caused by a failure under

warranty of any warranted part.

8. Throughout the off-road engine and equipment warranty period stated above, MTD Consumer Group Inc will maintain a supply of

warranted parts sufficient to meet the expected demand for such parts.

9. Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to

the owner. Such use will not reduce the warranty obligations of MTD Consumer Group Inc.

050790 Rev. D

10. Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or

modified parts by the ultimate purchaser will be grounds for disallowing a warranty claim. MTD Consumer Group Inc will not be liable to

warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.

WARRANTED PARTS:

The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if MTD

Consumer Group Inc demonstrates that the outdoor equipment has been abused, neglected, or improperly maintained, and that such abuse,

neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part. That notwithstanding, any adjustment

of a component that has a factory installed, and properly operating, adjustment limiting device is still eligible for warranty coverage. Further,

the coverage under this warranty extends only to parts that were present on the off-road equipment purchased.

The following emission warranty parts are covered (if applicable):

1. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor and internal parts (or fuel injection system)

• Fuel pump

• Fuel tank

2. Air Induction System

• Air cleaner

• Intake manifold

3. Ignition System

• Spark plug(s)

• Magneto ignition system

4. Exhaust System

• Catalytic converter

• SAI (Reed valve)

5. Miscellaneous Items Used in Above System

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

6. Evaporative Control

• Fuel hose

• Fuel hose clamps

• Tethered fuel cap

• Carbon canister

• Vapor lines

Page is loading ...

Troy-Bilt 13A879KS066 User manual

Brand: Troy-Bilt

Model: 13A879KS066

Category: Lawnmowers

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

español: Troy-Bilt 13A879KS066 Manual de usuario

Troy-Bilt 13A879KS066 User manual

This manual is also suitable for

Troy-Bilt 13A879KS066 User manual

in other languages

Related papers

Other documents