Indesit FH 51 IX CN S User guide

Brand: Indesit

Model: FH 51 IX CN S

Category: Microwaves

Type: User guide

FH 51 CN S

FH 51 IX CN S

English

Operating Instructions

OVEN

Contents

Operating Instructions,1

Warnings,2

Assistance,3

Description of the appliance,4

Description of the appliance,5

Installation,6

Electrical Connection,6

Start-up and use,8

Modes,8

Precautions and tips,11

Maintenance and care,11

中文

操作说明

烤箱

Contents

操作说明,1

警告,2

帮助,3

器具说明,4

器具说明,5

安装,13

电气连接,13

启动和使用,15

模式,15

注意事项和技巧,18

维护与保养,18

Warnings

WARNING: The appliance and its

accessible parts become hot during use.

Care should be taken to avoid touching

heating elements. Children less than 8

years of age shall be kept away unless

continuously supervised. This appliance

can be used by children aged from 8 years

and above and persons with reduced

physical, sensory or mental capabilities

or lack of experience and knowledge

if they have been given supervision

or instruction concerning use of the

appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and

user maintenance shall not be made by

children without supervision.

Do not use harsh abrasive cleaners or

sharp metal scrapers to clean the oven door

glass since they can scratch the surface,

which may result in shattering of the glass.

Never use steam cleaners or pressure

cleaners on the appliance.

WARNING: Ensure that the appliance is

switched off before replacing the lamp to

avoid the possibility of electric shock.

! When you place the rack inside, make

sure that the stop is directed upwards and

in the back of the cavity.

警告

警告：本器具及其可用零件在使用过程

中会变热。应当小心，避免接触加热元

件。不得让 8 岁以下儿童靠近，除非一

直有人看管。本器具可由 8 岁及以上儿

童、身体、感觉或智力能力减弱或缺乏

经验和知识的人使用，如果关于该器具

的安全使用，给予了监督或指导，并且

他们了解有关的危险。儿童不得玩耍该

器具。在没有监督的情况下，儿童不得

进行清洁和用户维修。

不要使用烈性擦洗剂或尖锐的金属刮刀来

清洁烤箱门玻璃，因为它们会刮伤表面，

从而可能导致玻璃碎裂。

绝不要对器具使用蒸汽清洁器或压力清

洁器。

警告：更换灯泡前，确保器具是关闭的，

以避免可能触电的情况。

! 当您把支架放置在内部时，请确保塞子

朝上，并在空腔共振器的后面。

Assistance

! Never use the services of an unauthorised technician.

Please have the following information to hand:

• The type of problem encountered.

• The appliance model (Mod.).

• The serial number (S/N).

The latter two pieces of information can be found on the

data plate located on the appliance.

帮助

! 切勿使用未经授权技术人员的服务。

请准备好以下信息：

• 遇到的问题类型。

• 该器具型号 (Mod.)。

• 序列号 (S/N)。

后两项信息可在该器具的数据板上找到。

Description of the appliance

Overall view

1. POSITION 1

2. POSITION 2

3. POSITION 3

4. POSITION 4

5. POSITION 5

6. GUIDES for the sliding racks

7. DRIPPING PAN

8. GRILL

9. Control panel

器具说明

整体视图

1. 位置 1

2. 位置 2

3. 位置 3

4. 位置 4

5. 位置 5

6. 滑架导轨

7. 油滴盘

8. 烤架

9. 控制面板

9 6

4 3

Description of the appliance

Control panel

1. SELECTOR Knob

2. TIMER Knob*

3. THERMOSTAT Knob

4. Indicator light THERMOSTAT

* Only available in certain models.

器具说明

控制面板

1. 选择器旋钮

2. 如何使用计时器*

3. 温控器旋钮

4. 指示灯温控器

*仅适用于某些型号。

Installation

! Please keep this instruction booklet in a safe place for

future reference. If the appliance is sold, given away or

moved, please make sure the booklet is also passed on to

the new owners so that they may benet from the advice

contained within it.

! Please read this instruction manual carefully: it contains

important information concerning the safe operation,

installation and maintenance of the appliance.

Positioning

! Do not let children play with the packaging material; it

should be disposed of in accordance with local separated

waste collection standards (see Precautions and tips).

! The appliance must be installed by a qualied professional

in accordance with the instructions provided. Incorrect

installation may damage property or cause harm to people

or animals.

Built-in appliances

Use an appropriate cabinet to ensure that the appliance

operates properly:

• The panels adjacent to the oven must be made of heat-

resistant material.

• Cabinets with a veneer exterior must be assembled with

glues which can withstand temperatures of up to 100°C.

• To install the oven under the counter (see diagram) or

in a kitchen unit, the cabinet must have the following

dimensions:

595 mm.

25 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

45 mm.

558 mm.

547 mm. min.

! The appliance must not come into contact with electrical

parts once it has been installed.

The indications for consumption given on the data plate

have been calculated for this type of installation.

Ventilation

To ensure adequate ventilation, the back panel of the

cabinet must be removed. It is advisable to install the oven

so that it rests on two strips of wood, or on a completely

at surface with an opening of at least 45 x 560 mm (see

diagrams).

560 mm.

45 mm.

Centring and xing

Secure the appliance to the cabinet by opening the oven

door and putting 4 screws into the 4 holes on the outer

frame.

! All parts which ensure the safe operation of the appliance

must not be removable without the aid of a tool.

Electrical Connection

The electrical connection to the mains must be made on

the appliance. The power voltage and frequency are as

indicated on the rating plate.

! THIS APPLIANCE MUST BE EARTHED.

Fitting the power supply cable

1. Open the terminal board

by inserting a screwdriver

into the side tabs of the

cover. Use the screwdriver

as a lever by pushing it

down to open the cover (see

diagram)

2. Install the power supply cable by loosening the

cable clamp screw and the three wire contact screws

L-N- .

Connect the wires to the

corresponding terminals:

the Blue wire to the terminal

marked (N), the Brown wire

to the terminal marked (L)

and the Yellow/Green wire

to the terminal marked

(see diagram).

3. Secure the cable by

fastening the clamp screw.

4. Close the cover of the terminal board.

Electrical Connection:

Voltage Frequency: see data plate

Fuse Section: 16A

Supply cable: 3x1.5mm

You can connect your oven to the system means of a

terminal board. Refer to above information for the minimal

cable sections and the calibration of the protective elements

according to the connection.

If the appliance is installed with a junction box, an

omnipolar circuit breaker - with a minimum contact

opening of 3mm - should be installed between the appliance

and the mains.

Power cable supply connection to the electrical mains:

We recommend you use a power supply cable which is

long enough to allow you to take the oven out of its recess

in the event of maintenance operations (only use HAR - H

05 - RRF quality cables tted with a plug conforming to the

regulations in force.

The plug must be accessible at all times.

Unplug the appliance before all operations, even

when replacing the oven lamp.

Using the appliance without correct earthing is highly

dangerous.

! After connecting the appliance to the exible cable,

tighten all the screws on the terminal board.

APPLIANCE SPECIFICATIONS

Dimensions*

width 43.5 cm

height 32,4 cm

depth 41.5 cm

Volume*

59 l

Dimensions**

width 45.5 cm

height 32,4 cm

depth 41.5 cm

Volume**

62 l

Electrical

connections

voltage: 220 - 230 V~ 50/60 Hz

(see data plate)

maximum power absorbed

2250 W

ENERGY

LABEL

* Only for models with drawn rails.

** Only for models with wire rails.

Directive 2002/40/EC on the label

of electric ovens. Standard EN 50304

Energy consumption for Natural

convection - heating mode:

Convection mode

Declared energy consumption for

Forced convection Class - heating

mode:

Multi-cooking

This appliance conforms to the

following European Economic

Community directives:

- 2006/95/EEC of 12/12/06 (Low

Voltage) and subsequent

amendments;

- 2004/108/EEC of 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments;

- 93/68/EEC of 22/07/93 and

subsequent amendments.

- 2012/19/EC and subsequent

amendments.

Start-up and use

WARNING! The oven

is provided with a stop

system to extract the racks

and prevent them from

coming out of the oven (1).

As shown in the drawing,

to extract them completely,

simply lift the racks, holding

them on the front part, and pull (2).

! The rst time you use your appliance, heat the empty oven

with its door closed at its maximum temperature for at least

half an hour. Make sure that the room is well ventilated

before switching the oven off and opening the oven door.

The appliance may emit a slightly unpleasant odour caused

by protective substances used during the manufacturing

process burning away.

Starting the oven

1. Select the desired cooking mode by turning the

SELECTOR knob.

2. Select the desired temperature with the THERMOSTAT

knob. See the Cooking advice table for cooking modes

and the suggested cooking temperatures (see Cooking

Modes).

3. When lit, the THERMOSTAT indicator light indicates that

the oven is heating up to the temperature set.

4. You may do the following during cooking:

- change the cooking mode by turning the SELECTOR knob.

- change the temperature by turning the THERMOSTAT

knob.

- stop cooking by turning the SELECTOR knob to the “0”

position.

! Never put objects directly on the oven bottom to avoid

damaging the enamel coating.

! Always place cookware on the rack(s) provided.

Cooling ventilation

In order to cool down the external temperature of the oven,

some models are tted with a cooling fan that blows out air

between the control panel and the oven door.

! Once the cooking has been completed, the cooling fan

remains on until the oven has cooled down sufciently.

Oven light

It goes on when selecting with the SELECTOR knob.

It stays on when a cooking mode is selected.

How to use the timer*

1. To set the buzzer, turn the TIMER knob clockwise almost

one complete revolution.

2. Turn the knob anticlockwise to set the desired time: align

the minutes shown on the TIMER knob with the indicator

on the control panel.

3. The timer operates in minutes: when the selected time

has elapsed, a buzzer will sound.

! The timer does not turn the oven on or off.

Modes

! A temperature value can be set for all cooking modes

between 60°C and Max, except for

• GRILL (recommended: set only to MAX power level);

• GRATIN (recommended: do not exceed 200°C).

TRADITIONAL OVEN mode

Both the top and bottom heating elements will come on.

With this traditional cooking mode, it is best to use one

cooking rack only; if more than one rack is used, the heat

will be distributed unevenly.

MULTI-COOKING mode

All the heating elements (top and bottom), as well as the fan,

will come on. Since the heat remains constant throughout

the oven, the air cooks and browns food uniformly. A

maximum of two racks may be used at the same time.

TOP OVEN mode

The top heating element comes on. This mode can be used

to brown food at the end of cooking.

GRILL mode

The top heating element comes on. The extremely high and

direct temperature of the grill makes it possible to brown

the surface of meats and roasts while locking in the juices

to keep them tender. The grill is also highly recommended

for dishes that require a high temperature on the surface:

such as beef steaks, veal, rib steak, lets, hamburgers

etc... Some grilling examples are included in the “Practical

Cooking Advice” paragraph. Always cook in this mode with

the oven door closed.

* Only available in certain models.

GRATIN mode

The top heating element, as well as the fan, will come on.

This combination of features increases the effectiveness of

the unidirectional thermal radiation of the heating elements

through forced circulation of the air throughout the oven.

This helps prevent food from burning on the surface,

allowing the heat to penetrate right into the food. Always

cook in this mode with the oven door closed.

Practical cooking advice

! Do not place racks in position 1 and 5 during fan-assisted

cooking. Excessive direct heat can burn temperature

sensitive foods.

! In the GRILL and GRATIN cooking modes, place the

dripping pan in position 1 to collect cooking residues (fat

and/or grease).

MULTI-COOKING

• Use position 2 and 4, placing the food that requires more

heat on 2.

• Place the dripping pan on the bottom and the rack on

top.

GRILL

• Insert the rack in position 3 or 4. Place the food in the

centre of the rack.

• We recommend that you set the maximum power level.

The top heating element is regulated by a thermostat

and may not always be on.

PIZZA

• For best results when cooking pizza, use the MULTI-

COOKING mode.

• Use a light aluminium pizza pan. Place it on the rack

provided.

For a crispy crust, do not use the dripping pan (prevents

crust from forming by extending cooking time).

• If the pizza has a lot of toppings, we recommend adding

the mozzarella cheese on top of the pizza halfway

through the cooking process.

Cooking

modes

Foods

Weight

(in kg)

Rack

position

Pre-heating

time (min)

Recommended

temperature

Cooking

time

(minutes)

Convection

Oven

Duck

Roast veal or beef

Pork roast

Biscuits (short pastry)

Tarts

200

180

65-75

70-75

70-80

15-20

30-35

Multi-cooking

Pizza (on 2 racks)

Lasagne

Lamb

Roast chicken + potatoes

Mackerel

Plum cake

Cream puffs (on 2 racks)

Biscuits (on 2 racks)

Sponge cake (on 1 rack)

Sponge cake (on 2 racks)

Savoury pies

1+1

0.5

1.5

2 and 4

230

180

200

180

170

190

180

170

200

15-20

30-35

40-45

60-70

30-35

40-50

20-25

10-15

15-20

20-25

25-30

Top oven

Browning food to perfect cooking - 3/4 15 220 -

Grill

Soles and cuttlefish

Squid and prawn kebabs

Cod filet

Grilled vegetables

Veal steak

Cutlets

Hamburgers

Mackerels

Toasts

3 or 4

Max

8-10

6-8

10-15

15-20

7-10

15-20

2-3

Gratin

Grilled chicken

Cuttlefish

1.5

200

55-60

30-35

Cooking advice table

The cooking times listed above are intended as guidelines only and may be modified according to personal tastes.

Precautions and tips

! This appliance has been designed and manufactured

in compliance with international safety standards. The

following warnings are provided for safety reasons and

must be read carefully.

General safety

• The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial use.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

• When moving or positioning the appliance, always use

the handles provided on the sides of the oven.

• Do not touch the appliance while barefoot or with wet or

damp hands and feet.

• The appliance must be used by adults only for

the preparation of food, in accordance with the

instructions provided in this booklet. Any other

use of the appliance (e.g. for heating the room)

constitutes improper use and is dangerous. The

manufacturer may not be held responsible for any

damage caused as a result of improper, incorrect

and unreasonable use of the appliance.

• Do not touch the heating elements or certain parts

of the oven door when the appliance is in use; these

parts become extremely hot. Keep children well away

from the appliance.

• Make sure that the power supply cables of other electrical

appliances do not come into contact with the hot parts of

the oven.

• The ventilation and heat dispersal openings must never

be obstructed.

• Always grip the oven door handle in the centre: the ends

may be hot.

• Always use oven gloves when placing cookware in the

oven or when removing it.

• Do not use aluminium foil to line the bottom of the oven.

• Do not place ammable materials in the oven: if the

appliance is switched on accidentally, the materials could

catch re.

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Do not perform any cleaning or maintenance work without

having disconnected the appliance from the electricity

mains.

• If the event of malfunctions, under no circumstances

should you attempt to perform the repairs yourself.

Contact an authorised Service Centre (see Assistance).

• Do not rest objects on the open oven door.

• Do not let children play with the appliance.

• The appliance should not be operated by people (including

children) with reduced physical, sensory or mental

capacities, by inexperienced individuals or by anyone

who is not familiar with the product. These individuals

should, at the very least, be supervised by someone who

assumes responsibility for their safety or receive preliminary

instructions relating to the operation of the appliance.

• The appliance is not intended to be operated by

means of an external timer or separate remote-

control system.

Disposal

• When disposing of packaging material: observe local

legislation so that the packaging may be reused.

• The European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment (WEEE), requires

that old household electrical appliances must not

be disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product

reminds you of your obligation, that when you dispose

of the appliance it must be separately collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their

old appliance.

Respecting and conserving the environment

• You can help to reduce the peak load of the electricity

supply network companies by using the oven in the

hours between late afternoon and the early hours of

the morning. The cooking mode programming options,

the “delayed cooking” mode (see Cooking modes) and

“delayed automatic cleaning” mode (see Care and

Maintenance) in particular, enable the user to organise

their time efciently.

• Always keep the oven door closed when using the GRILL

and GRATIN modes: this will achieve improved results

while saving energy (approximately 10%).

• Check the door seals regularly and wipe them clean

to ensure they are free of debris so that they adhere

properly to the door, thus avoiding the dispersal of heat.

Maintenance and care

Switching the appliance off

Disconnect your appliance from the electricity supply before

carrying out any work on it.

Cleaning the appliance

• Slight differences in colour on the front of the oven are due

to the different materials used, i.e. glass, plastic or metal.

• Any shady areas resembling grooves on the oven door

glass are caused by reections from the oven light.

• The enamel is branded at very high temperatures. This

process may cause colour variations. This is normal and

will not affect appliance operation in any way. The thin

edges of the sheet metal cannot be entirely enamelled

and may therefore appear to be unnished. This will not

affect the rust protection.

• The stainless steel or enamel-coated external parts and

the rubber seals may be cleaned using a sponge that

has been soaked in lukewarm water and neutral soap.

Use specialised products for the removal of stubborn

stains. After cleaning, rinse and dry thoroughly. Do not

use abrasive powders or corrosive substances.

• The inside of the oven should ideally be cleaned after

each use, while it is still lukewarm. Use hot water and

detergent, then rinse well and dry with a soft cloth. Do

not use abrasive products.

• All accessories can be washed like everyday crockery,

and are even dishwasher safe.

• We recommend that detergents are not sprayed directly

onto the control panel, but that a sponge is used instead.

! Never use steam cleaners or pressure cleaners on the

appliance.

Cleaning the oven door

Clean the glass part of the oven door using a sponge and

a non-abrasive cleaning product, then dry thoroughly with

a soft cloth. Do not use rough abrasive material or sharp

metal scrapers as these could scratch the surface and cause

the glass to crack.

For more thorough cleaning

purposes, the oven door may be

removed:

1. Open the oven door fully (see

diagram).

2. Use a screwdriver to lift up and turn the small levers F

located on the two hinges (see diagram).

3. Grip the door on the two external

sides and close it approximately

half way. Unlock the door by

pressing on the clamps F, then

pull the door towards you lifting it

out of its seat (see diagram).

To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals

are damaged, please contact your nearest Service Centre

(see Assistance). We recommend that the oven is not used

until the seals have been replaced.

Replacing the light bulb

To replace the oven light

bulb:

1. Remove the glass cover

of the lamp-holder.

2. Remove the light bulb

and replace it with a similar

one: Wattage 25 W, cap E

14.

3. Replace the glass cover

(see diagram).

! Do not use the oven lamp as/for ambient lighting.

* Only available on certain models.

安装

! 请将此使用说明书保存在安全之处，以供将来参考。如

果出售、赠送或转移此器具，请确保同时将说明书交给新

用户，以便他们可以利用其内含的建议。

! 请仔细阅读本操作说明书：内含有关此器具的安全操作、

安装和维护的重要信息。

安置

! 不要让儿童玩包装材料；应按照当地分类废物收集标准来

处理（参见注意事项和技巧）。

! 此器具须由合格专业人员根据提供的说明进行安装。不正

确的安装可能会损坏财产或导致人身或动物伤害。

内置器件

使用适合的橱柜，以确保该器具正常运行：

• 与烤箱毗邻的面板必须是耐热材料制成的。

• 安装胶合表层的橱柜须使用能承受温度高达 100°C 的

胶水。

• 如将烤箱安装在柜子下（参见图示）或厨房组件内，橱

柜须符合以下尺寸要求：

595 mm.

25 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

45 mm.

558 mm.

547 mm. min.

! 该器具安装完成后，不能与电气元件接触。

对于此类安装，数据板上给出的耗电指示已经过计算。

通风

为了确保通风充足，必须移除橱柜背面的面板。建议将烤箱

平稳安装在两条木板上，或一个面积至少为 45 x 560 毫米

的开放式完整平面上（参见图示）。

560 mm.

45 mm.

定心和固定

打开烤箱门并在外框上的 4 个洞孔内置入 4 颗螺丝，以将

此器具固定在橱柜里。

! 在不使用工具的情况下，所有保证此器具安全操作的零

部件是不可移除的。

电气连接

将电气连接到主电源须在器具上进行。标牌上标明了电源

电压和频率。

! 此器具须接地。

调整电源线

1. 将螺丝起子放进盖子侧边

的镶嵌片里，打开接线板。

将螺丝起子作为杠杆向下推

动，打开盖子（参见图示）

2. 拧松电缆紧固螺丝和三线接触螺丝 L-N- ，安装电

源线。.

将电线连接至相应的端子：蓝线对应标为(N)的端子，棕线

对应标为(L)的端子，以及黄线/绿线对应的端子

（参见图示）。

3. 拧紧紧固螺丝，固定电

缆。

4. 关闭接线板的盖子。

电气连接：

电压频率：参见数据板

保险丝组件：16A

电源线：3x1.5 平方毫米

可通过接线板将烤箱连接到系统。有关最小电缆部件和根据

连接校准保护元件的数据，请参照上述信息。

如果此器具安装时配置了接线盒，应在器具和主电源之间

安装全极断路器——接点之间至少保留 3 毫米的空间。

将电源线连接到电气主电源：

我们建议您使用足够长的电源线，以便在维修操作中将烤

箱移出橱柜（只能使用配备符合现行规定插头的 HAR - H

05 - RRF 优质电缆）。

插头须随时可连接。

进行任何操作之前须拔掉此器具的电源，即使在更换烤箱

灯泡时也不例外。

在没有正确接地装置的情况下使用此器具具有高危性。

! 将器具连接到软电缆后，拧紧接线板上的所有螺丝。

启动和使用

警告！炉子配备了起止系

统，用于取出支架并放置它

们脱离炉子 (1)。如图纸所

示，要想完全取出它们，只

需提起支架，握住支架的前

端然后拉 (2)。

! 首次使用此器具时，应关闭烤箱门，在其最高温度下加热

空烤箱半小时以上。在关闭烤箱开关和打开烤箱门之前，应

确保室内通风良好。保护性物质在生产过程中燃烧可能会致

使该器具散发出一种轻微的异味。

启动烤箱

1. 转动选择器旋钮，选择所需的烹饪模式。

2. 使用温控器旋钮，选择所需的温度。烹饪模式和建议烹

饪温度（参见烹饪模式），请参见烹饪建议表。

3. 温控器指示灯亮起时，表明烤箱正在加热至设定温度。

4. 在烹饪过程中，您可以：

——转动选择器旋钮，更换烹饪模式。

——转动温控器旋钮，更改烹饪温度。

——将选择器旋钮转到 “0” 位置上，停止烹饪。

! 不能将物体直接放在烤箱底部上，以免损坏其瓷釉涂层。

! 必须将烹饪用具放在所提供的烤架上。

冷却通风

为了降低烤箱的外部温度，有些型号配备了冷却风扇，可将

控制面板和烤箱门之间的空气吹出。

! 烹饪完成后，冷却风扇仍会继续运作，直至烤箱充分冷

却。

烤箱灯

使用选择器旋钮选择时，此灯亮起。选择烹饪模式

时，此灯保持恒亮。

如何使用计时器*

1．将计时器按钮顺时针旋转到底来设置蜂鸣器。

2．逆时针拨动旋钮来设置理想的时间：控制面板上能看

到所需要的时间。

3．时间以分钟来计时：当到达选择的时间时，蜂鸣器会

有响声。

! 计时器不能开或关闭烤箱。

模式

! 除了以下模式外，所有烹饪模式的温度值均可设定在

60°C 和最大值之间：

• 烤（建议：只能设置为最大功率）；

• 焗（建议：不要超过 200°C）。

传统烤箱模式

顶部和底部加热元件同时开启。使用这种传统烹饪模式

时，最好只使用一个烤架；如果使用多个烤架，热量会分

布不均。

多功能烹饪模式

所有加热元件（顶部和底部）以及风扇都会开启。由于整

个烤箱内热量保持不变，热气会均匀地烹饪食物至均匀的

棕色。最多可同时使用两个烤架。

顶部烤箱模式

顶部加热元件开启。此模式可用于烹饪结束时将食物烤至

棕色。

烧烤模式

顶部加热元件开启。极高的炙烤温度直接作用于食物上，可

将肉类和烘焙类食物的表面烤至棕色，并同时锁住水分以保

持食物的柔软性。强烈推荐这种烧烤模式用于表面需要高

温烹饪的菜肴。如牛排、小牛肉、肋骨牛排、里脊、汉堡

等……“实用烹饪建议”一段中例举了一些烧烤食谱。使

用此烹饪模式时，须保持烤箱门关闭。

焗模式

顶部加热元件以及风扇都会开启。这两种功能的结合让整

个烤箱内充满强制气流，可提高加热元件的单向热辐射的

效力。如此一来，热量可直接渗透到食物里面，有助于防

止食物表面烧焦。使用此烹饪模式时，须保持烤箱门关闭。

实用烹饪建议

! 在使用风扇功能的烹饪模式下，不能将烤架置于 1 和 5

处。过度的直接加热可能会引起热敏性食物燃烧。

! 在烤和焗烹饪模式下，将油滴盘置于 1 处盛放烹饪过程

中的残留物（脂肪和/或油脂）。

*仅适用于某些型号。

多功能烹饪

• 使用位置 2 和 4，对热量要求更高的烹饪，将食物置于

2 处。

• 将油滴盘置于底层，烤架置于顶层。

烤架

• 将烤架插入位置 3 和 4。将食物置于烤架的中间位置。

• 建议设置最大功率。顶部加热元件由恒温器控制，并不

会一直处于开启状态。

披萨

• 烹饪披萨时，使用多功能烹饪模式已达最好效果。

• 使用轻型铝制披萨盘。将它置于所提供的烤架上。烹饪

薄皮披萨时，不能使用油滴盘（防止延长烹饪时间的情况

下形成饼皮）。

• 如果披萨上有很多馅料，建议在烹饪中途往披萨表面加

一层马苏里拉奶酪。

200

180

65-75

70-75

70-80

15-20

30-35

1+1

0.5

1.5

2 4

230

180

200

180

170

190

180

170

200

15-20

30-35

40-45

60-70

30-35

40-50

20-25

10-15

15-20

20-25

25-30

- 3/4 15 220 -

3 4

8-10

6-8

10-15

15-20

7-10

15-20

2-3

1.5

200

55-60

30-35

2 4

注意事项和技巧

! 该器具的设计和生产符合国际安全标准。为了安全起见，

请仔细阅读以下警告事项。

安全总则

• 此器具设计为家用型，不得用于商业或工业用途。

• 此器具不能安全在室外，包括有顶盖的区域。将此器具

暴露于雨水和风暴中具有高危性。

• 移动或定位此器具时，须使用烤箱侧边提供的把手。

• 请勿赤脚或使用潮湿的手和脚触碰此器具。

• 此器具仅可用于成年人根据本册子中所提供的说明来烹

饪食物。使用此器具用作任何其他用途（如房间供热）

均为使用不当，具有高危性。对于不正当、不正确和不

合理使用此器具的行为引起的任何损坏,生产商不承担责

任。

• 在此器具的使用过程中，请勿触摸加热元件或烤箱门的

某些部件；这些部件会变得温度极高。应让儿童远离该

器具。

• 确保其他电器的电源线不会接触到烤箱的高温部件。

• 不得阻塞通风及热气扩散出口。

• 应抓烤箱门手把的中间位置：两端可能会很烫。

• 放置或移除烹饪用具时，应使用烤箱手套。

• 不要使用铝箔覆盖烤箱底部。

• 不要在烤箱内放置易燃物质：如此器具被意外开启，该

材料可能会着火。

• 拔除此器具电源时，应从电源插座中拔出插头；不要拉

扯电线。

• 未将此器具断电的情况下，不能进行任何清洗或维修工

作。

• 发生故障时，任何情形下都不应自己尝试进行维修。联

系经过授权的服务中心（参见帮助）。

• 不要在敞开的烤箱门上放置任何东西。

• 不能让儿童玩耍该器具。

• 体力、感官或智力下降者（包括儿童），或缺乏经验的

个人，或任何对此产品不熟悉的人都不能操作此器具。

最起码，这类人应在为他们的安全承担责任的人的监督

下，或是知悉有关此器具操作的初步说明的情况下，才

能操作此器具。

• 本器具不能通过外部计时器或独立的远程控制系统来操

作。

处理

• 处理包装材料时：遵循当地法规，以便该包装可能可再

次利用。

• 根据欧洲指令 2012/19/EC 对废弃电气和电子设备制定

的要求，不能按照正常未分类的城市废物流来处理旧家

用电器。须单独收集旧家用电器，以便能最大限度对其

所含的材料进行回收和循环利用以及减小对人类健康和

环境的影响。

产品上打叉的“带轮垃圾桶”标志旨在提醒您，应负责另

行收集、处理该器具。

消费者应与当地授权商或零售店联系获取正确处理旧家

电的相关信息。

尊重和保护环境

• 在傍晚和清晨时分使用烤箱，可帮助降低供电公司的高

峰负荷。烹饪模式程序选项，尤其是“延迟烹饪”模式

（参见烹饪模式）以及“延迟自动清洗”模式（参见维

护与保养）有利于用户有效安排自己的时间。

• 使用烤和焗模式时，始终保持烤箱门关闭：如此可达到

更好的烹饪效果，同时节约能源（大约 10%）。

• 定期检查烤箱门的密封圈并擦拭干净，确保上面没有碎

渣，以使其能紧附在门上，进而避免热气扩散。

维护与保养

关闭器具开关

在进行任何工作之前，应将此器具断电。

清洁器具

• 由于使用的材料不同，如玻璃、塑料或金属，烤箱前面

部分的颜色会有细微差异。

• 任何类似烤箱门玻璃上的凹槽的阴影区域都是由烤箱灯

光反射引起的。

• 瓷釉是在很高的温度下会出现烙印效果。这个过程可能

会引起颜色变化。这属于正常现象，并不会影响器具的

使用。金属板的薄边无法完全上釉，因此可能看上去像

未涂层一样。这并不会影响防锈。

• 可使用浸在温水里的海绵和中性皂液清洗不锈钢或瓷釉

涂层的外部零件以及橡胶密封圈。应使用专门产品去除

顽固污渍。清洗后，应冲洗干净并彻底干燥。不要使用

研磨粉或腐蚀性物质。

• 每次使用烤箱后，应在其还处于微温的状态下进行清洗

干净。使用热水和洗涤剂清洗，然后冲洗干净并使用软

布擦干。不要使用研磨产品。

• 所有配件可像日常餐具那样清洗，甚至可使用洗碗机清

洗。

• 建议不要将洗涤剂直接喷到控制面板上，而是使用海绵

来代替。

! 绝不要对器具使用蒸汽清洁器或压力清洁器。

清洁烤箱门

使用海绵和非研磨性清洗产品清洁烤箱门的玻璃部分，然后

用软布彻底擦干。不要使用粗糙的研磨性材料或尖锐的金属

刮削器，这样可能会刮坏玻璃表面并导致其破裂。 .

为达到更彻底的清洗目的，可移除

烤箱门。

1. 完全打开烤箱门（参见图示）。

2. 使用螺丝起子抬起并转动位于两个铰链上的小撬杆 F（

参见图示）。

3. 抓住门的两个外侧边，并使其

保持在半合状态。按住位于 F 的

夹钳，打开烤箱门，然后将门朝自

己的方向拉并将它抬离其位置（参

见图示）。

按照相反的顺序操作，可重新装上

烤箱门。

检查密封件

定期检查烤箱周围的烤箱门密封圈。如密封圈受损，请联

系最近的服务中心（参见帮助）。更换密封圈之前，建议

不要使用烤箱。

更换灯泡

如需更换烤箱灯泡，应：

1. 移除灯座上的玻璃罩。

2. 卸下灯泡，换上同类灯

泡：瓦数 25 W，灯头 E 14

。

3. 重现装上玻璃罩（参见

图示）。

! 不要将烤箱灯用作/用于环境照明。

侧部及后部催化衬板*

这些涂以特殊瓷釉的嵌板，可以吸收烹饪食物过程中飞溅

的油滴。

此种瓷釉相当牢固，因此可承受多种配件（如烤架、油滴

盘等）的来回滑动而不受损坏。该表面可能会出现白色

痕迹；但这些并不会造成任何问题。

然而，应避免以下行为：

——用锋利的物体（如刀具）刮擦瓷釉；

——用洗涤剂或磨蚀性材料。

*仅适用于某些型号。

195102355.02

10/2013 - XEROX FABRIANO

Indesit FH 51 IX CN S User guide

Brand: Indesit

Model: FH 51 IX CN S

Category: Microwaves

Type: User guide

Download PDF

report

in other languages

日本語: Indesit FH 51 IX CN S ユーザーガイド