Amazon Renewed NR90AES1 User manual

Instruction and safety manual

Manuel d’instructions et de sécurité

Instrucciones y manual de seguridad

Model Nailer

Modèle Cloueur

Modelo Clavador

NR 90AD (S1) • NR 90AE (S1)

DANGER

Improper use of this Nailer can result in death or serious injury!

This Manual contains important information about product safety.

Read and understand this Manual before operating the Nailer.

Never allow anyone who has not reviewed this manual to use the tool.

This manual should be stored in safe place.

DANGER

Une utilisation incorrecte et sans respecter la sécurité de ce cloueur risque d’entraîner la mort

ou des blessures graves !

Ce manuel renferme des instructions importantes sur la sécurité de l’outil.

Lire et bien assimiler ce manuel avant d’utiliser le cloueur.

Cet outil ne doit jamais être utilisé par une personne n’ayant pas pris connaissance du manuel.

Ce mode d’emploi doit être conservé dans un endroit sûr.

PELIGRO

¡La utilización inadecuada e insegura de este clavador puede resultar en lesiones serias o en la

muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y entienda este manual antes de utilizar el martillo neumático.

La herramienta no deberá utilizarse sin haber leído previamente este manual.

Este manual debe ser guardado en un lugar seguro.

NR 90AD (S1) NR 90AE (S1)

Page is loading ...

3

English

IMPORTANT SAFETY INFORMATION

Read and understand tool labels and all of the operating instructions, safety precautions and warnings

in this manual before operating or maintaining this Nailer.

Failure to follow warnings could result in DEATH or SERIOUS INJURY

Most accidents that result from the operation and maintenance of Nailers are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it

occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Manual and in the sections which contain the

operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by DANGERS and WARNINGS

on the Nailer and in this Manual.

NEVER use this Nailer for applications other than those speciﬁ ed in this Manual.

DEFINITIONS OF SIGNAL WORDS

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER

○

SINGLE SEQUENTIAL ACTUATION MECHANISM:

First, press the push lever against the wood; next, pull the trigger to drive the fastener.

After nailing once, nailing will not be possible again until the Trigger is released and pressed again.

○

CONTACT ACTUATION MECHANISM:

First, press the push lever against the wood; next, pull the trigger to drive the fastener.

First, pull the trigger; next, press the push lever against the wood to drive the fastener.

If the Trigger is held back, a nail will be driven each time the Push Lever is pressed against the wood.

4

English

SAFETY

IMPORTANT SAFETY INSTRUCTIONS - FOR USING NAILERS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

●

General

To reduce the risks of electric shock, ﬁ re, and injury to persons, READ ALL THE INSTRUCTIONS BEFORE USING

THE TOOL.

DANGER

1. OPERATORS AND OTHERS IN WORK AREA

MUST WEAR EYE PROTECTION (SAFETY

GLASSES WITH SIDE SHIELDS).

When operating the Nailer, always wear

safety glasses with side shields, and

make sure others in work area wear

safety glasses, too.

Safety glasses must conform to the

requirements of American National

Standards Institute, ANSI Z87.1 and

provide protection against ﬂ ying particles

both from the front and side.

The employer must enforce the use of

safety glasses by the Nailer operator and

others in work area.

2. NEVER USE OXYGEN OR OTHER BOTTLED

GASES. EXPLOSION MAY OCCUR.

Never use oxygen, combustible gases or

any other bottled gases as a power

source for the Nailer.

Use of the above gases is dangerous, as

the Nailer will explode.

Use only clean, dry, regulated

compressed air.

WARNING

3. NEVER POINT TOOL AT YOURSELF OR OTHERS

IN WORK AREA.

Always assume that the Nailer contains

fasteners.

Never point the Nailer toward yourself or

others, whether it contains fasteners or

not.

If fasteners are mistakenly driven, it can

lead to severe injuries.

Never engage in horseplay with the

Nailer.

Respect the Nailer as a working

implement.

4. DO NOT PLACE FINGER ON TRIGGER AND KEEP

FINGER AWAY FROM THE TRIGGER WHEN NOT

DRIVING FASTENERS TO AVOID ACCIDENTAL

FIRING.

Never carry the Nailer with ﬁ nger on Trigger since

you could drive a fastener unintentionally and injure

yourself or someone else.

Always carry the Nailer by the handle only.

5. CHOICE OF TRIGGERING METHOD IS

IMPORTANT.

Read and understand section titled “METHODS OF

OPERATION.” (pages 15 – 16)

6. DO NOT MAKE CONTACT WITH SAFETY TIP

(PUSH LEVER) WHEN NOT DRIVING FASTENERS.

5

English

SAFETY — Continued

WARNING

When using tools, basic precautions should always be followed, Including the following:

1. Work area

(1) Keep the work area clean and well lighted.

Cluttered benches and dark areas increase the risks

of electric shock, ﬁ re, and injury to persons.

(2) Do not operate the Nailer in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases, or dust.

The Nailer is able to create sparks resulting in the

ignition of the dust or fumes.

(3) Keep bystanders, children, and visitors away

while operating the Nailer. Distractions are able to

result in the loss of control of the Nailer.

2. Personal safety

(1) Stay alert. Watch what you are doing and use

common sense when operating the Nailer.

Do not use the Nailer while tired or under the

inﬂ uence of drugs, alcohol, or medication.

A moment of inattention while operating the Nailer

increases the risk of injury to persons.

(2) Dress properly. Do not wear loose clothing or

jewelry. Contain long hair. Keep hair, clothing,

and gloves away from moving parts.

Loose clothes, jewelry, or long hair increases the

risk of injury to persons as a result of being caught in

moving parts.

(3) Avoid unintentional starting. Be sure the switch

is oﬀ before connecting to the air supply. Do

not carry the Nailer with your ﬁ nger on the switch or

connect the Nailer to the air supply with the switch on.

(4)

– Disconnect the Nailer from

the air source before making adjustments, doing

Nailer maintenance, clearing jams, touching

the Push Lever, when not in use, leaving work

area, loading, or unloading the Nailer, handing

it to another person. Never attempt to clear a jam

or repair the Nailer unless you have disconnected

air hose from the Nailer and removed all remaining

fasteners from the Nailer. The Nailer should never be

left unattended since people who are not familiar with

the Nailer might handle it and injure the themselves.

Such precautionary measures reduce the risk of

injury to persons.

(5) Do not overreach. Keep proper footing and

balance at all times. Proper footing and balance

enables better control of the Nailer in unexpected

situations.

(6) Use safety equipment. A dust mask, non-skid

safety shoes and a hard hat must be used for the

applicable conditions.

(7)

– Risk of hearing loss. Wear

ear protection.

(8) Always wear head protection.

Always wear head protection to protect your

head from ﬂ ying objects.

(9) Do not attach the hose or Nailer to your body.

Attach the hose to the structure to reduce the risk of

loss of balance if the hose shifts.

(10)

– Place Nailer properly on

workpiece. Do not fasten on top of another fastener.

This is able to cause the fastener to be deﬂ ected and

hit someone, or cause the Nailer to react and result in

a risk of injury to persons.

3. Nailer use and care

(1) Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by hand or against the body is

unstable and is able to lead to loss of control.

(2) Do not force the Nailer. Use the correct Nailer for

the application. The correct Nailer will do the job

better and safer at the rate for which the Nailer is

designed.

(3) Do not use the Nailer if the switch does not

turn the Nailer on or oﬀ . Any Nailer that cannot be

controlled with the switch is dangerous and must be

repaired.

Never use Nailer which is defective or operating

abnormally. If the Nailer appears to be operating

unusually, making strange noises, or otherwise

appears defective, stop using it immediately and

arrange for repairs by a Hitachi authorized service

center.

(4) Disconnect the Nailer from the air source before

making any adjustments, changing accessories,

or storing the Nailer. Such preventive safety

measures reduce the risk of starting the Nailer

unintentionally.

6

English

(5) Store the Nailer when it is idle out of reach of

children and other untrained persons. A Nailer is

dangerous in the hands of untrained users.

(6) Maintain the Nailer with care. Keep the

Nailer Clean and lubricated for better and safer

performance.

(7) Check for misalignment or binding of moving

parts, breakage of parts, and any other condition

that aﬀ ects the Nailer’s operation.

If damaged, have the Nailer serviced before using.

Because of high air pressure in the Nailer, cracks in

the surface are dangerous. To avoid this, do not drop

the Nailer or strike the Nailer against hard surfaces;

and do not scratch or engrave signs on the Nailer.

Many accidents are caused by poorly maintained

Nailers. There is a risk of bursting if the Nailer is

damaged.

(8) Use only accessories that are identiﬁ ed by

Hitachi for the speciﬁ c Nailer. Use of an accessory

not intended for use with the speciﬁ c Nailer ,

increases the risk of injury to persons.

(9) Use only those fasteners listed in the

Accessories section of this manual. Fasteners not

identiﬁ ed for use with this Nailer by Hitachi are able to

result in a risk of injury to persons or Nailer damage

when used in this Nailer.

4. Service

(1) Tool service must be performed only by qualiﬁ ed

repair personnel.

(2) When servicing a Nailer, use only identical

replacement parts. Use only authorized parts.

(3) Use only the lubricants supplied with the Nailer

or speciﬁ ed by Hitachi.

5. Air source

(1) Never connect to an air source that is capable of

exceeding 200 psi (13.7 bar 14 kgf/cm

2

).

Over pressurizing the Nailer is able to result in

bursting, abnormal operation, breakage of the Nailer

or serious injury to persons.

DO NOT EXCEED 120 psi (8.3 bar 8.5 kgf/cm

2

).

Use only clean, dry, regulated compressed air at the

rated pressure or within the rated pressure range as

marked on the Nailer.

Always verify prior to using the Nailer that the air

source has been adjusted to the rated air pressure or

within the rated air-pressure range.

(2) Never use oxygen, carbon dioxide, combustible

gases or any bottled gas as an air source for the

Nailer. Such gases are capable of explosion and

serious injury to persons.

6. Others

(1) Before starting work, check the nailing operation

switching device.

This Hitachi nailer includes a nailing operation

switching device.

Before starting work, check the setting of the

operation switching device.

If the switching device is not set properly, the nailer

will not operate correctly.

(2) Be careful of double ﬁ re due to recoil. If the Push

Lever is unintentionally allowed to re-contact the

workpiece following recoil, an unwanted fastener will

be driven. In order to avoid this undesirable double

ﬁ re,

○

Intermittent operation (Trigger ﬁ ring)

1) Set the switching device to SINGLE SEQUENTIAL

ACTUATION MECHANISM.

2) Pull the trigger rapidly and ﬁ rmly.

○

Continuous operation (Push lever ﬁ ring)

1) Set the switching device to CONTACT

ACTUATION MECHANISM.

2) Do not press the nailer against the wood with

excessive force.

3) Separate the nailer from the wood as it recoils

after nailing.

(3) Never Use NON relieving coupler on Nailer. If a

non relieving coupler is used on the Nailer, the Nailer

can remain charged with air after disconnecting

and thus will be able to drive a fastener even after

disconnecting. The Nailer and air hose must have a

hose coupling such that all pressure is removed from

the Nailer when the coupling joint is disconnected.

SAFETY — Continued

WARNING

7

English

(4) Check Push Lever before use. Make sure the

Push Lever operates properly. (The Push Lever may

be called “Safety”.) Never use the Nailer unless the

Push Lever is operating properly, otherwise the Nailer

could drive a fastener unexpectedly. Do not tamper

with or remove the Push Lever, otherwise the Push

Lever becomes inoperable.

(5) Keep all screws and covers tightly in place. Keep

all screws and covers tightly mounted.

Check their condition periodically. Never use the

Nailer if parts are missing or damaged.

(6) Do not load fasteners with Trigger or Push Lever

depressed. When loading fasteners into the Nailer

or when connecting the air hose,

1) do not depress the Trigger;

2) do not depress the Push Lever; and

3) keep the Nailer pointed downward.

(7) Keep hands and feet away from ﬁ ring head

during use. Never place your hands or feet closer

than 8 inches (200 mm) from the ﬁ ring head. A

serious injury can result if the fasteners are deﬂ ected

by the workpiece, or are driven away from the point of

entry.

SAFETY — Continued

WARNING

(8) Do not drive fasteners into thin boards or near

corners and edges of workpiece.

The fasteners can be driven through or away from the

workpiece and hit someone.

(9) Never drive fasteners from both sides of a wall

at the same time. The fasteners can be driven into

and through the wall and hit a person on the opposite

side.

(10) Check for live wires. Avoid the risk of severe

electrical shock by checking for live electrical wires

that may be hidden by walls, ﬂ oors or ceilings. Turn

oﬀ the breaker switch to ensure there are no live

wires.

(11) Never carry Nailer by hose.

(12) Do not disconnect air hose from Nailer with

ﬁ nger on Trigger. The Nailer can ﬁ re when re-

connected to An air supply.

(13) Handle Nailer correctly. Operate the Nailer

according to this Manual. Never allow the Nailer to

be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

(14) Never use Nailer for applications other than

those speciﬁ ed in this manual.

(15) Never modify or alter a Nailer. Doing so may cause

it to malfunction and personal injuries may result.

SAVE THIS MANUAL AND

KEEP IT AVAILABLE FOR OTHERS!

EMPLOYER’S RESPONSIBILITIES

1. Ensure that this MANUAL is available to operators

and personnel performing maintenance.

2. Ensure that Nailers are used only when operators and

others in work area are wearing EYE PROTECTION.

3. Enforce the use of EYE PROTECTION by operators

and others in work area.

4. Keep Nailers in safe working order.

5. Maintain Nailers properly.

6. Ensure that Nailers which require repair are not

further used before repair.

8

English

OPERATION

NOTE: The information contained in this Manual is designed to assist you in the safe operation of the Nailer.

Some illustrations in this Manual may show details or attachments that diﬀ er from those on your own Nailer.

NAME OF PARTS

Nailing operation switching device

Switching

Device

Upward position

Switching

Device

Downward position

SINGLE SEQUENTIAL ACTUATION

MECHANISM

(Switching device: upward position)

CONTACT ACTUATION

MECHANISM

(Switching device: downward

position)

Piston O-Ring

Exhaust Cover

Driver Blade

Piston

Nose

Nail Feeder (A)

Ribbon Spring

Magazine

Nail Stopper

Cap

Air Plug (Sold separately)

Push Lever

Firing Head (Outlet)

Nail Feeder (B)

Body

Trigger

Head Guard

Switching

Device

9

English

SPECIFICATIONS

Model NR90AD (S1) NR90AE (S1)

Operating pressure

70 – 120 psi (4.9 – 8.3 bar, 5 – 8.5 kgf/cm

2

)

Dimensions

Length × Height × Width

18-3/16" × 12-11/16" × 4-15/16"

(462 mm × 322 mm × 125 mm)

20-3/4" × 12-11/16" × 4-15/16"

(527 mm × 322 mm × 125 mm)

Weight 7.0 lbs. (3.2 kg) 7.5 lbs. (3.4 kg)

Nail capacity 50 – 74 nails (2 strips) 64 – 70 nails (2 strips)

Air consumption

.088 ft

3

/cycle at 100 psi

(2.5 ltr/cycle at 6.9 bar)

(2.5 ltr/cycle at 7 kgf/cm

2

)

Air inlet

3/8 NPT Thread

NAIL SELECTION

WARNING

●

Be sure to use only the genuine HITACHI nails for the NR90AD (S1) or the NR90AE (S1). The use of any

other nails can result in tool malfunction and/or nail breakdown, leading to serious injuries.

Only nails shown in the Table below can be driven with this Nailer.

NR90AD (S1)

Paper collated strip nails

Clipped-head nails

Min. Max.

.113"

(2.9 mm)

2" (50 mm)

.266"

(6.8 mm)

.148"

(3.8 mm)

3-1/2" (90 mm)

.303"

(7.7 mm)

10

English

NR90AE (S1)

Plastic-collated strip nails

Full-head nails

Min. Max.

.113"

(2.9 mm)

2" (50 mm)

.286"

(7 mm)

.148"

(3.8 mm)

3-1/2" (90 mm)

.3"

(7.6 mm)

ACCESSORIES

DANGER

●

Accessories other than those shown below

can lead to malfunction and resulting

injuries.

STANDARD ACCESSORIES

1

Safety glasses ..........................................................1

OPTIONAL ACCESSORIES

... sold separately

○

Pneumatic Tool Lubricant

.8 oz. (25 cc) oil feeder (Code No. 877153)

4 oz. (120 cc) oil feeder (Code No. 874042)

1 quart (1 ltr) can (Code No. 876212)

NOTE: Accessories are subject to change without any

obligation on the part of HITACHI.

APPLICATIONS

○

Floor and wall framing.

○

Truss build-up, Window build-up.

○

Subﬂ ooring and roof decking.

○

Wall sheathing.

○

Mobile home and modular housing construction.

BEFORE OPERATION

Read section titled “SAFETY” (pages 4 – 7).

Make sure of the followings before operation.

WORKING ENVIRONMENT

WARNING

●

No ﬂ ammable gas, liquid or other ﬂ ammable

objects at worksite.

●

Clear the area of children or unauthorized

personnel.

AIR SUPPLY

DANGER

●

NEVER use oxygen or other

bottled gases. Explosion may

occur.

11

English

WARNING

●

Never connect Nailer to pressure which

potentially exceeds 200 psi (13.7 bar 14 kgf/cm

2

).

●

Never use non relieving coupler on

Nailer.

1. Power source

○

Use only clean, dry, regulated compressed air as a

power source for this Nailer.

○

Air compressors used to supply compressed air to

this Nailer must comply with the requirements of

the latest version of ANSI Standard B 19.3 “Safety

Standard For Compressors For Process Industries”.

○

Moisture or oil in the air compressor may accelerate

wear and corrosion in the Nailer.

Drain daily.

2. Filter-Regulator-Lubricator

○

Use a regulator with a pressure range of 0 – 120 psi

(0 – 8.3 bar 0 – 8.5 kgf/cm

2

).

○

Filter-regulator-lubricator units supply an optimum

condition for the Nailer and extend the Nailer life.

These units should always be used.

Filter ........ The ﬁ lter removes moisture and dirt mixed

in compressed air.

Drain daily unless ﬁ tted with an automatic

drain.

Keep the ﬁ lter clean by regular

maintenance.

Regulator

... The regulator controls the operating

pressure for safe operation of the Nailer.

Inspect the regulator before operation to

be sure it operates properly.

Lubricator

... The lubricator supplies an oil mist to the

Nailer.

Inspect the lubricator before operation to

be sure the supply of lubricant is adequate.

Use Hitachi pneumatic tool lubricant.

Nailer

Side

Filter

Lubricator

Compressor

Side

Regulator

3. Air hose

○

Air hose must have a minimum working pressure

rating of 150 psi (10.4 bar 10.6 kgf/cm

2

) or 150% of

the maximum pressure produced in the system,

whichever is higher.

4. Air consumption

Using the Air consumption table and the Air

compressor size formula, ﬁ nd a correct compressor

size.

Air consumption table

Operating pressure

psi

(bar)

(kgf/cm

2

)

80

(5.5)

(5.6)

90

(6.2)

(6.3)

100

(6.9)

(7)

Air consumption

ft

3

/cycle

(Itr/cycle)

.062

(1.7)

.075

(2.1)

.088

(2.5)

Air compressor size formula

Amount of air required

= number of Nailers

× average nails driven each minute per Nailer

× air consumption at given air pressure

× safety factor (always 1.2)

Example: 2 Nailers operating at 100 psi driving 30

nails per minute

Amount of air required

= 2 × 30 × .088 (2.5) × 1.2

= 6.3 CFM (ft

3

/min) (180 ltr/min)

After making the calculations as shown above, you

should ﬁ nd a compressor providing 6.3 CFM of air

that is required.

LUBRICATION

It is important that the Nailer be properly lubricated.

Without proper lubrication, the Nailer will not work

properly and parts will wear prematurely.

○

Use Hitachi pneumatic tool lubricant.

Do not use detergent oil or additives. These lubricants

will harm the O-rings and other rubber parts. This will

cause the Nailer to malfunction.

○

Filter-regulator-lubricator units should always be

used.

Keep the lubricator ﬁ lled with Hitachi pneumatic tool

lubricant.

○

If a lubricator is not available, supply 5 – 10 drops of

Hitachi pneumatic tool lubricant into the air plug on

the Nailer twice a day.

COLD WEATHER CARE

○

Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area until beginning the

work.

12

English

○

If the Nailer is already cold, bring it in a warm area

and allow the Nailer to warm up before use.

1

Reduce the air pressure to 64 psi (4.4 bar 4.5 kgf/

cm

2

).

2

Remove all nails from the Nailer.

3

Connect the air hose and free-ﬁ re (blank-ﬁ re) the

Nailer.

The lowered air pressure will be enough to free-

ﬁ re the Nailer.

Slow speed operation tends to warm up the

moving part.

CAUTION

●

Do not free-ﬁ re the Nailer at high pressure.

TESTING THE NAILER

DANGER

●

Operators and others in work

area MUST wear safety

glasses with side shields

which conforms to ANSI Z87.1

speciﬁ cations.

WARNING

●

Never use Nailer unless push lever is

operating properly.

Before actually beginning the nailing work, test the Nailer

by using the checklist below. Conduct the tests in the

following order.

If abnormal operation occurs, stop using the Nailer and

contact a Hitachi authorized service center immediately.

(1) DISCONNECT AIR HOSE FROM NAILER.

REMOVE ALL NAILS FROM NAILER.

□

ALL SCREWS MUST BE TIGHTENED.

If any screws are loose, tighten them.

□

THE PUSH LEVER AND TRIGGER MUST MOVE

SMOOTHLY.

Trigger

Do not connect

air hose

Push Lever

(2) Adjust the air pressure to 70 psi (4.9 bars 5 kgf/cm

2

).

Connect the air hose.

Do not load any nails in the Nailer.

Set the switching device to the upward position

(SINGLE SEQUENTIAL ACTUATION MECHANISM).

(Set the switching device to the upward position

completely as shown in the diagram. Otherwise, it will

not operate properly.)

Switching Device

Upward position

□

THE NAILER MUST NOT LEAK AIR.

(3) Remove the ﬁ nger from the trigger and press the

push lever against the workpiece.

□

THE NAILER MUST NOT OPERATE.

Depress Push Lever

Do not pull Trigger

13

English

ADJUSTING AIR PRESSURE

WARNING

●

Do not exceed

120 psi (8.3 bar

8.5 kgf/cm

2

).

Adjust the air pressure at recommended operating

pressure 70 – 120 psi (4.9 – 8.3 bar 5 – 8.5 kgf/cm

2

)

according to the length of nails and the hardness of

workpiece.

The correct air pressure is the lowest pressure which will

do the job. Using the Nailer at a higher than required air

pressure unnecessarily over stresses the Nailer.

LOADING NAILS

WARNING

●

When loading nails into Nailer,

1) do not pull trigger;

2) do not depress push lever; and

3) keep Nailer pointed downward.

(1) Insert nail strip into the back of the magazine.

Magazine

(2) Slide the nail strip forward in the magazine.

The nail strip should pass the nail stopper.

Nail Stopper

(4) Separate the push lever from the workpiece.

Next, point the nailer downward, pull the trigger and

then wait in that position for 5 seconds or longer.

□

THE NAILER MUST NOT OPERATE.

Pull Trigger

(5)

1

Without touching the trigger, depress the push

lever against the workpiece.

Pull the trigger.

□

THE NAILER MUST OPERATE.

2

Remove the ﬁ nger from the trigger.

□

Nailer operation will end (the driver blade will

return to the top).

(6) Set the switching device to the downward position

(CONTACT ACTUATION MECHANISM).

(Set the switching device to the downward position

completely as shown in the diagram. Otherwise, it will

not operate properly.)

Switching Device

Downward position

With the Nailer oﬀ the workpiece, pull the trigger.

Depress the push lever against the workpiece.

□

THE NAILER MUST OPERATE.

(7) If no abnormal operation is observed, you may load

nails in the Nailer.

Drive nails into the workpiece that is the same type to

be used in the actual application.

□

THE NAILER MUST OPERATE PROPERLY.

14

English

(3) Pull the nail feeder (B) back to engage the nail feeder

(A) to the nail strip.

Nail Feeder (B)

Nail Feeder (A)

NOTE

●

Quietly push the Nail Feeders (A) and (B) against the

nail.

If the Nail Feeders (A) and (B) are released from

backward the magazine and bumped against the nail,

the connecting paper of the nail can be damaged.

●

Use nail strip of more than 5 nails.

5

The Nailer is now ready to operate.

Removing the nails:

1

Pull the nail feeder (B) backward.

2

Return the nail feeder (B) forward quietly while

pushing the nail feeder (A).

3

Push the nail stopper toward the magazine side, and

pull out nails from the back of the magazine.

1

2

Nail Feeder (B)

Nail Feeder (A)

3

Nail Stopper

Nails

NAILER OPERATION

Read section titled “SAFETY”(pages 4 – 7).

DANGER

●

Operators and others in work

area MUST wear safety

glasses with side shields

which conforms to ANSI Z87.1

speciﬁ cations.

WARNING

●

NEVER point tool at yourself

or others in work area.

●

Keep ﬁ ngers AWAY from trigger when not driving

nails to avoid accidental ﬁ ring.

●

Choice of triggering method is important.

Please read and understand “Methods of

Operation” below.

●

Before starting work, check the nailing operation

switching device.

This Hitachi nailer includes a nailing operation

switching device.

Before starting work, make sure that the

switching device is properly set.

If the switching device is not set properly, the

nailer will not operate correctly.

●

Never place your hands or feet closer than 8

inches (200 mm) from ﬁ ring head when using.

●

Do not drive nails on the top of other nails or

with Nailer at too steep of an angle; nails can

ricochet and hurt someone.

●

Do not drive nails into thin boards or near

corners and edges of workpiece. Nails can be

driven through or away from workpiece and hit

someone.

15

English

●

Never drive nails from both sides of a wall at the

same time. Nails can be driven into and through

the wall and hit a person on the opposite side.

●

Never use Nailer which is defective or operating

abnormally.

●

Do not use Nailer as hammer.

●

Disconnect air hose from Nailer when:

1) it is not in use;

2) leaving work area;

3) moving it to another location;

4) handing it to another person; and

5) changing switching device.

This Hitachi nailer is equipped with a nailer operation

switching device.

Use SINGLE SEQUENTIAL ACTUATION MECHANISM or

CONTACT ACTUATION MECHANISM in accordance with

the work to be performed.

Explanation of the various nailing operations

○

SINGLE SEQUENTIAL ACTUATION MECHANISM:

First, press the push lever against the workpiece;

next, pull the trigger to drive the nail.

After nailing once, nailing will not be possible again

until the trigger is released and pressed again.

○

CONTACT ACTUATION MECHANISM: First, press

the push lever against the workpiece; next, pull the

trigger to drive the nail. Or,

pull the trigger; next, press the push lever against the

workpiece to drive the nail.

If the trigger is held back, a nail will be driven each

time the push lever is pressed against the workpiece.

METHODS OF OPERATION

This Nailer is equipped with the push lever and does

not operate unless the push lever is depressed (upward

position).

There are two methods of operation to drive nails with this

Nailer.

They are:

1. Intermittent operation (Trigger ﬁ re):

2. Continuous operation (Push lever ﬁ re):

(1) Intermittent operation (Trigger ﬁ re)

Use the SINGLE SEQUENTIAL ACTUATION

MECHANISM setting.

WARNING

●

For intermittent operation, set the switching

device to the upward position completely.

(i.e. Set to SINGLE SEQUENTIAL ACTUATION

MECHANISM.)

●

To avoid double ﬁ ring or accidental ﬁ ring due

to recoil.

1) Set the switching device to SINGLE

SEQUENTIAL ACTUATION MECHANISM.

2) Pull the trigger rapidly and ﬁ rmly.

1

Set the switching device to the upward position

(to set to SINGLE SEQUENTIAL ACTUATION

MECHANISM).

(Set the switching device to the upward position

completely as shown in the diagram. Otherwise,

it will be set to CONTACT ACTUATION

MECHANISM.)

2

Position the nail outlet on the workpiece with

ﬁ nger oﬀ the trigger.

3

Depress the push lever ﬁ rmly until it is completely

depressed.

4

Pull the trigger to drive a nail.

5

Remove ﬁ nger from the trigger.

To continue nailing in a separate location, move the

nailer along the wood, repeating steps

2

–

5

as

required.

Switching Device

1

Upward position

Trigger

Push Lever

3

4

WARNING

●

A nail will ﬁ re each time the trigger is

depressed as long as the push lever remains

depressed.

(2) Continuous operation (Push lever ﬁ re)

Using CONTACT ACTUATION MECHANISM

16

English

WARNING

●

To avoid double ﬁ ring or accidental ﬁ ring due

to recoil.

1) Do not press the nailer against the wood

with excessive force.

2) Separate the nailer from the wood as it

recoils after nailing.

1

Set the switching device to the downward position

(to set to CONTACT ACTUATION MECHANISM).

(Set the switching device to the downward

position completely as shown in the diagram.

Otherwise, it will not operate properly.)

2

Pull the trigger with the Nailer oﬀ the workpiece.

3

Depress the push lever against the workpiece to

drive a nail.

4

Move the Nailer along the workpiece with a

bouncing motion.

Each depression of the push lever will drive a nail.

As soon as the desired number of nails have been

driven, remove ﬁ nger from the trigger.

Switching Device

1

Downward position

Previously pull the trigger

Push Lever

2

4

WARNING

●

Keep your ﬁ nger oﬀ the trigger except during

fastening operation, because serious injury

could result if the push lever accidentally

contacts you or others in work area.

●

Keep hands and body away from the

discharge area. This Hitachi nailer may

bounce from the recoil of driving a fastener

and unwanted subsequent fastener may be

driven, possibly causing injury.

●

Some types of loaded nails can spark out of

the muzzle during a nail driving operation.

Exericise caution!

The SINGLE SEQUENTIAL ACTUATION MECHANISM

is for use where precision fastener placement is desired.

The SINGLE SEQUENTIAL ACTUATION MECHANISM

may reduce the possibility of bodily injury to you or others

in the work area compared to the CONTACT ACTUATION

MECHANISM. This is because it is less likely to drive

an unwanted nail if you keep the trigger pulled and

accidentally bump the push lever against yourself or

others.

The SINGLE SEQUENTIAL ACTUATION MECHANISM

may also reduce the speed of operation compared

to the CONTACT ACTUATION MECHANISM. The

SINGLE SEQUENTIAL ACTUATION MECHANISM is

recommended to inexperienced users.

NOTE

●

If all warnings and instructions are followed, safe

operation is possible with all two systems: SINGLE

SEQUENTIAL ACTUATION MECHANISM and

CONTACT ACTUATION MECHANISM.

●

Always handle nails and package carefully. If nails

are dropped, collating plastic may be broken.

●

After nailing:

1) disconnect air hose from the Nailer;

2) remove all nails from the Nailer;

3) supply 5 – 10 drops of Hitachi pneumatic tool

lubricant into the air plug on the Nailer; and

4) open the petcock on the air compressor

tank to drain any moisture.

ADJUSTING THE NAILING DEPTH

To assure that each nail penetrates to the same depth, be

sure that:

1) the air pressure to the Nailer remains constant

(regulator is installed and working properly), and

2) the Nailer is always held ﬁ rmly against the workpiece.

If nails are driven too deep or shallow into the workpiece,

adjust the nailing in the following order.

17

English

1

DISCONNECT AIR HOSE FROM NAILER.

Adjuster

Disconnect air hose

15

2

If nails are driven too deep, turn the adjuster to the

shallow side.

2

Too Deep

Flush

Turn Adjuster

If nails are driven too shallow, turn the adjuster to the deep

side.

Turn Adjuster

Flush

2

Too Shallow

3

Stop turning the adjuster when a suitable position is

reached for a nailing test.

4

Connect the air hose.

ALWAYS WEAR EYE PROTECTOR.

Perform a nailing test.

5

DISCONNECT AIR HOSE FROM NAILER.

6

Choose a suitable position for the adjuster.

MAINTENANCE

NOTE: The information contained in this Manual is designed to assist you in the safe maintenance of the Nailer.

Some illustrations in this Manual may show details or attachments that diﬀ er from those on your own Nailer.

MAINTENANCE AND INSPECTION

Read section titled “SAFETY” (pages 4 – 7).

WARNING

●

Disconnect air hose and remove all nails

from Nailer when:

1) doing maintenance and inspection; and

2) clearing a jam.

1. Inspecting the magazine

1

DISCONNECT AIR HOSE.

2

Clean the magazine. Remove paper chips or wooden

chips which may have accumulated in the magazine.

Lubricate it with Hitachi pneumatic tool lubricant.

Cloth

Disconnect

air hose

1

CAUTION

●

Check that the nail feeder slides smoothly by

pulling it with ﬁ nger.

If not smooth, nails can be driven at an irregular

angle and hurt someone.

18

English

2. Storing

○

When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

○

Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area.

○

When not in use, the Nailer should be stored in a

warm and dry place.

Keep out of reach children.

3. WARNING LABEL

Change the WARNING LABEL if missing or

damaged.

A new WARNING LABEL is available from a Hitachi

authorized service center.

Warning Label

4. Maintenance chart (See page 18)

5. Operator troubleshooting (See page 19)

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

●

Repair, modiﬁ cation and inspection of Hitachi

Power Tools must be carried out by a Hitachi

Authorized Service Center.

This Parts List will be helpful if presented with

the tool to the Hitachi Authorized Service Center

when requesting repair or other maintenance. In

the operation and maintenance of power tools,

the safety regulations and standards prescribed

in each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modiﬁ ed to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

SERVICE AND REPAIRS

WARNING

●

Only service personnel trained by Hitachi,

distributor or employer shall repair the Nailer.

●

Use only parts supplied or recommended by

Hitachi for repair.

All quality Nailers will eventually require servicing or

replacement of parts because of wear from normal use.

NOTE

Speciﬁ cations are subject to change without any

obligation on the part of HITACHI.

Maintenance chart

ACTION WHY HOW

Drain air line ﬁ lter daily. Prevent accumulation of moisture

and dirt.

Open manual petcock.

Keep lubricator ﬁ lled. Keep the Nailer lubricated. Fill with Hitachi pneumatic tool

lubricant.

Clean ﬁ lter element — then blow air

through ﬁ lter in direction opposite to

normal ﬂ ow.

Prevent clogging of ﬁ lter with dirt. Follow manufacturer’s instructions.

Clean magazine and feeder

mechanism.

Prevent a jam. Blow clean daily.

Keep push lever working properly. Promote operator safety and eﬃ cient

Nailer operation.

Blow clean daily.

Lubricate the Nailer after nailing. Extend the Nailer life. Supply 5 – 10 drops of lubricant into

the Nailer.

Drain air compressor. Keep the Nailer operated properly. Open petcock on air

19

English

Operator troubleshooting

Most minor problems can be resolved quickly and easily using the table below.

If problems persist, contact a Hitachi authorized service center for assistance.

PROBLEM CHECK METHOD CORRECTION

Nailer operates, but no nail is driven. Check for a jam. Clear a jam.

Check function of nail feeder per

page 17.

Clean and lubricate.

Ribbon spring weakened or

damaged?

Replace ribbon spring.

Check for proper nails. Use only recommended nails.

Weak drive.

Slow to cycle.

Check air pressure. Increase air pressure. (Do not exceed

120 psi (8.3 bars, 8.5 kgf/cm

2

))

—————— Use Hitachi pneumatic tool lubricant.

Driver blade worn? Contact Hitachi for replacement.

Piston O – ring worn or damaged?

Drives too deep. Check air pressure. Reduce air pressure.

(Adjust 70 – 120 psi)

Skipping nails.

Intermittent feed.

Check for proper nails. Use only recommended nails.

Check function of nail feeder per

page 17.

Clean and lubricate.

Ribbon spring weakened or

damaged?

Replace ribbon spring.

—————— Use Hitachi pneumatic tool lubricant.

Piston O – ring cut or heavily worn? Contact Hitachi for replacement.

Nail feeder (A) worn or damaged? Replace nail feeder (A).

Nails jam.

Driven nail is bent.

Check for proper nails. Use only recommended nails.

Driver blade worn? Contact Hitachi for replacement.

Nail feeder (A) worn or damaged? Replace nail feeder (A).

Drives properly during normal

operation, but does not drive fully at

faster nailing speeds.

Check inside diameter of air hose. Use larger air hose.

Page is loading ...

507

Code No. C99196163 T

Printed in Taiwan

Issued by

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo 108-6020, Japan

Distributed by

PO Box 970

Braselton, GA 30517

450 Export Blvd. Unit B,

Mississauga ON L5S 2A4

Amazon Renewed NR90AES1 User manual

Amazon Renewed NR90AES1 User manual

in other languages

Other documents