MULTIPLEX Pc Kabel Rx S Telemetrie Owner's manual
- Type
- Owner's manual
© MULTIPLEX Modellsport GmbH & Co. KG z Neuer Weg 2 z D-75223 Niefern z GERMANY
USB PC – RX Interface
Anleitung 2
Instructions 3
Instructions 4
Instrucciones 5
Istruzioni 6
Stand: 20.02.07
Page is loading ...
Operating Instructions
USB-PC lead for RX-SYNTH receivers
MULTIPLEX Modellsport GmbH & Co.KG • Neuer Weg 2 • D-75223 Niefern-Öschelbronn • www.multiplex-rc.de Page 1/1
Operating Instructions USB-PC lead for RX-SYNTH receivers # 82 5811 (07-02-15/MW) • Errors and omissions excepted. •
MULTIPLEX
! These operating instructions are an integral part
of the product, and contain important information
and safety notes. Store them in a safe place, and be
sure to pass them on to the new owner if you
dispose of the product.
1. INTRODUCTION
Use the USB-PC lead for RX-SYNTH receivers # 8 5149 to con-
nect your MULTIPLEX RX-SYNTH series receiver to your PC in
order to transfer updates, exchange data or use additional func-
tionality. The PC software required for this (DataManager for RX-
SYNTH receivers) is available as a free download from our Inter-
net site www.multiplex-rc.de
under DOWNLOADS Æ
SOFTWARE.
Exception:
The USB-PC lead for RX-SYNTH receivers cannot be used with
the RX-6-SYNTH light receiver.
2. INSTALLATION
2.1 System requirements
• Windows 95 / 98 / 2000 / ME / XP (Microsoft)
• 1 free USB Port
2.2 Installing the USB driver
The USB driver must be installed before you connect the USB-
PC lead to your receiver and the PC.
The first step is to download the driver to your computer from our
Internet site www.multiplex-rc.de
under DOWNLOADS Æ
SOFTWARE Æ Driver for USB cable # 8 5148 and -49. Install
the software by double-clicking on the file
“setup_usb_driver.exe”, and follow the on-screen instructions.
Once the driver is installed, it is safe to plug in the USB-PC lead.
Continue to follow the on-screen instructions.
2.3 Installing DataManager for RX-SYNTH receivers
Download the latest version of DataManager for RX-SYNTH re-
ceivers from our Internet site www.multiplex-rc.de
under
DOWNLOADS Æ SOFTWARE Æ PC software for synthesizer
receivers, and install the software by double-clicking on the
Setup file. Follow the installation instructions on the screen.
If you have installed Adobe Acrobat Reader (available for
downloading from www.adobe.com
), the DataManager instruc-
tions will automatically be opened when the installation is com-
plete. Print out the instructions for later reference, and follow the
instructions and recommendations they contain.
3. CONNECTING THE RECEIVER TO THE PC
Connect your receiver to a free USB port on your PC using the
USB-PC lead connected to the Diagnosis socket, marked “D” or
“B/D”. You can use the USB extension lead (supplied) if neces-
sary.
Connect the receiver battery, switch the receiver on, run Data-
Manager for RX-SYNTH receivers, and continue as described in
the DataManager instructions.
Note:
If the usual socket for the receiver battery is in use by the USB-
PC lead for RX-SYNTH receivers, you can connect the battery to
any other vacant servo socket on the receiver.
4. GUARANTEE
Our products are covered by the currently valid statutory guaran-
tee regulations. If you wish to make a claim under guarantee,
please contact the model shop where you originally purchased
the unit.
The guarantee does not cover faults caused by:
• incorrect handling, incorrect connections, reversed polarity
• the use of accessories other than original MULTIPLEX items
• modifications or repairs not carried out by MULTIPLEX or by
an authorised MULTIPLEX Service Centre
• accidental or deliberate damage
• normal wear and tear
• use of the unit outside the stated Specification
5. CE APPROVAL
This product satisfies the following harmonised
European directives:
EN55014-1 : 2000
EN55014-2 : 1997
EN60950-1 : 2001 + A11
You are therefore the owner of a product whose design fulfils the
protective aims of the European Community relating to the safe
operation of equipment.
6. DISPOSAL INFORMATION
Electrical equipment marked with the cancelled waste
bin symbol must not be discarded in the standard
household waste; instead it must be taken to a suitable
specialist disposal or recycling system.
In the countries of the EU (European Union), electrical
equipment must not be discarded via the normal domes-
tic refuse system (WWW - Waste of Electrical and Electronic
Equipment, Directive 2002/96/EG). You can take unwanted
equipment to your nearest local authority waste collection point
or recycling centre, where the staff will dispose of it correctly and
at no cost to yourself.
By returning your unwanted equipment you can make an impor-
tant contribution to the protection of our shared environment!
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
MULTIPLEX Pc Kabel Rx S Telemetrie Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
MULTIPLEX Rx 7 U 7 Ds Ipd Owner's manual
-
-
-
-
-
-
MULTIPLEX RX-7-DR Owner's manual
-
-
-
