Pro-Form PFEVEL73908 User manual

Brand: Pro-Form

Model: PFEVEL73908

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manual

for future reference.

Model No. PFEVEL73908.0

Serial No.

Write the serial number in the

space above for reference.

Serial

Number

Decal

USERʼS MANUAL

QUESTIONS?

If you have questions, or if there are

missing parts, please contact us:

Call: 08457 089 009

Outside UK: 0 (44) 113 3877133

Fax: 0 (44) 113 3877125

Website: www.iconsupport.eu

E-mail: [email protected]

Write:

ICON Health & Fitness, Ltd.

Unit 4

Revie Road Industrial Estate

Revie Road, Beeston

Leeds, LS11 8JG

www.iconeurope.com

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

PROFORM is a registered trademark of ICON IP, Inc.

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the

warning decal(s). If a decal is missing or

illegible, see the front cover of this manual

and request a free replacement decal.

Apply the decal in the location shown. Note:

The decal(s) may not be shown at actual size.

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your elliptical exerciser before using your elliptical

exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or

through the use of this product.

1. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or per-

sons with pre-existing health problems.

2. It is the responsibility of the owner to ensure

that all users of the elliptical exerciser are

adequately informed of all precautions.

3. Your elliptical exerciser is intended for home

use only. Do not use your elliptical exerciser

in a commercial, rental, or institutional set-

ting.

4. Keep your elliptical exerciser indoors, away

from moisture and dust. Place your elliptical

exerciser on a level surface, with a mat

beneath it to protect the floor or carpet.

Make sure that there is at least 3 ft. (0.9 m)

of clearance in the front and rear of your

elliptical exerciser and 2 ft. (0.6 m) on each

side

5. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

6. Keep children under age 12 and pets away

from your elliptical exerciser at all times.

7. Your elliptical exerciser should not be used

by persons weighing more than 250 lbs.

(113 kg).

8. Wear appropriate exercise clothes when

exercising; do not wear loose clothes that

could become caught on your elliptical exer-

ciser. Always wear athletic shoes for foot

protection.

9. Hold the handgrip pulse sensor or the upper

body arms when mounting, dismounting, or

using your elliptical exerciser.

10. Keep your back straight while using your

elliptical exerciser; do not arch your back.

11. The pulse sensor is not a medical device.

Various factors, including the userʼs move-

ment, may affect the accuracy of heart rate

readings. The pulse sensor is intended only

as an exercise aid in determining heart rate

trends in general.

12. When you stop exercising, allow the pedals

to slowly come to a stop.

13. If you feel pain or dizziness while exercising,

stop immediately and cool down.

14. Use your elliptical exerciser only as

described in this manual.

IMPORTANT PRECAUTIONS

BEFORE YOU BEGIN

hank you for selecting the new PROFORM

EFLEX

STEP 2 elliptical exerciser. The REFLEX STEP 2 pro-

vides a selection of features designed to make your

workouts at home more effective and enjoyable.

For your benefit, read this manual carefully before

you use the elliptical exerciser. If you have ques-

tions after reading this manual, please see the front

over of this manual. To help us assist you, note the

product model number and serial number before con-

tacting us. The model number and the location of the

serial number decal are shown on the front cover of

his manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

Pulse Sensor

Pedal Spring

Pedal Disc

*Water bottle is not included

Wheel

Pedal

Water Bottle Holder*

Upper Body Arm

Console

ASSEMBLY

Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the

packing materials. Do not dispose of the packing materials until assembly is completed.

In addition to the included tools, assembly requires a Phillips screwdriver , an adjustable

wrench , and a rubber mallet .

Use the drawings below to identify the small parts used for assembly. The number in parentheses below each

drawing is the key number of the part, from the PART LIST near the end of this manual. The number following

the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if

it has been preassembled.

M4 x 16mm

Screw (52)–4

M10 Split

Washer (59)–5

M10 Locknut (33)–6

M10 Bolt Set (74)–2

Upper Body Arm

Washer (55)–2

Spring Bracket

Washer (35)–2

M8 Locknut (38)–8

M8 x 45mm Button Bolt (50)–4

M10 x 25mm Patch

Screw (40)–5

M10 x 75mm Carriage Bolt (34)–4

Wave Washer

(43)–2

M8 x 25mm Patch

Screw (56)–2

M4 x 19mm

Screw (26)–2

M10 x 74mm Button Bolt (28)–2

23mm Wave

Washer (81)–2

2. While another person lifts the rear of the Frame

(1), attach the Rear Stabilizer (9) to the Frame

with two M10 x 75mm Carriage Bolts (34) and

two M10 Locknuts (33).

dentify the Front Stabilizer (10). Make sure

that the Wheels (22) are oriented as shown.

While another person lifts the front of the Frame

(1), attach the Front Stabilizer (10) to the Frame

with two M10 x 75mm Carriage Bolts (34) and

two M10 Locknuts (33).

To make assembly easier, read the

information on page 5 before you begin.

Avoid pinching

the wires

3. Have another person hold the Upright (2) near

the Frame (1). Make sure that the hexagonal

holes are in the indicated location.

onnect the Extension Wire Harness (44) to the

Wire Harness (79).

Slide the Upright (2) onto the Frame (1).

Tip: Avoid pinching the wires. Attach the

Upright (2) with two M10 x 74mm Button Bolts

(28), two M10 Split Washers (59), and two M10

Locknuts (33). Make sure that the Locknuts

are in the hexagonal holes.

Hexagonal

Holes

4. While another person holds the Upright

Extension (73) near the Upright (2), insert the

Extension Wire Harness (44) upward through

the Upright Extension.

Hold the upper end of the Extension Wire

Harness (44) and insert the Upright Extension

(73) into the Upright (2).

Tip: Avoid pinching the wire. Attach the

Upright Extension (73) with three M10 x 25mm

Patch Screws (40) and three M10 Split Washers

(59).

Avoid pinching

the wire

5. The Console (23) can use four D batteries (not

ncluded); alkaline batteries are recommended.

IMPORTANT: If the Console has been

exposed to cold temperatures, allow it to

warm to room temperature before inserting

batteries. Otherwise, you may damage the

console displays or other electronic compo-

ents. Remove the battery cover, insert the bat-

teries into the battery compartment, and reat-

tach the battery cover. Make sure to orient the

batteries as shown by the diagram inside

the battery compartment.

To purchase an optional AC adapter, contact

the store where you purchased this product

or call the telephone number on the front

cover of this manual. To avoid damaging the

console, use only a manufacturer-supplied

AC adapter. Plug one end of the AC adapter

into the jack on the console; plug the other end

into an outlet installed in accordance with all

local codes and ordinances.

Battery

Cover

Batteries

6. While another person holds the Console (23)

near the Upright Extension (73), connect the

console wire harness to the Extension Wire

Harness (44).

Insert the excess wire into the Upright

Extension (73).

Tip: Avoid pinching the wires. Attach the

Console (23) to the Upright Extension (73) with

four M4 x 16mm Screws (52).

Console Wire

Harness

Avoid pinching

the wires

7. Attach the Water Bottle Holder (65) to the

pright (2) with two M4 x 19mm Screws (26).

8. Identify the Left Upper Body Arm (6), which is

marked with an “L” sticker.

Insert the Left Upper Body Arm (6) into an

Upper Body Leg (5); make sure that the

hexagonal holes are in the indicated

location.

Attach the Left Upper Body Arm (6) with two M8

x 45mm Button Bolts (50) and two M8 Locknuts

(38). Make sure that the Locknuts are in the

hexagonal holes. Do not tighten the Button

Bolts yet.

Repeat this step for the Right Upper Body

Arm (not shown) and the other Upper Body

Leg (not shown).

Hexagonal

Holes

Grease

9. Apply a generous amount of the included

rease to the Pivot Axle (7). Then, apply grease

to two Wave Washers (43).

Insert the Pivot Axle (7) into the Upright (2), and

center the Pivot Axle.

lide a Wave Washer (43) onto the left side of

the Pivot Axle (7).

Orient an Upper Body Arm Spacer (47) so that

the arrow points toward the floor. Slide the

Upper Body Arm Spacer onto the Left Upper

Body Arm (6).

Slide the Left Upper Body Arm (6) onto the

Pivot Axle (7).

Attach the Left Upper Body Arm (6) with an M8

x 25mm Patch Screw (56) and an Upper Body

Arm Washer (55).

Press the tabs on an Upper Body Arm Cap (46)

into the Upper Body Arm Spacer (47).

Attach the Right Upper Body Arm (8) in the

same way.

Tabs

Hole

Slots

10. Identify the left Pedal Spring (11) and the Left

Pedal (13), which are marked with “L” stickers.

Position the Left Pedal (13) and a Pedal Plate

(80) around the left Pedal Spring (11) as shown.

Make sure that the hole in the Pedal Plate

fits over the bumper on the underside of the

left Pedal Spring.

Insert the tabs on the Pedal Plate (80) into the

slots in the Left Pedal (13).

Attach the Pedal Plate (80) to the Left Pedal

(13) with two M8 Locknuts (38).

Attach the Right Pedal (not shown) in the

same way.

Bumper

Arrow

11. Identify the Left Rear Spring Bracket (12), which

is located on the left Pedal Spring (11).

pply a small amount of grease inside the

Pedal Spring Bushings (37). Then, apply grease

o the axle on the left Disc Crossbar (16).

Slide a Spring Spacer (63) and a 23mm Wave

Washer (81) onto the axle; make sure that the

flat side of the Spring Spacer is facing the

elliptical exerciser.

Slide the Left Rear Spring Bracket (12) onto the

axle.

Attach the Left Rear Spring Bracket (12) with an

M10 x 25mm Patch Screw (40) and a Spring

Bracket Washer (35).

Repeat this step for the Right Rear Spring

Bracket (not shown).

Grease

13. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be

left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the

elliptical exerciser.

12. Hold the lower end of the left Upper Body Leg

(5) inside the Front Spring Bracket (76), which

is located on the left Pedal Spring (11).

Apply grease to an M10 Bolt Set (74).

Attach the Upper Body Leg (5) to the Front

Spring Bracket (76) with the M10 Bolt Set (74).

Do not overtighten the Bolt Set; the Upper

Body Leg must pivot freely.

Tighten the M8 x 45mm Button Bolts (50) in the

left Upper Body Leg (5).

Repeat this step on the other side of the

elliptical exerciser.

Grease

14. Remove the battery cover from the back of the

onsole (23).

Connect the wire on the receiver (A) to the wire

in the Console (23). Hold the receiver so that

he antenna is oriented as shown and is fac-

ing upward.

Remove the paper from the adhesive pad on

the back of the receiver (A). Press the receiver

onto the indicated location inside the battery

compartment. Then, reattach the battery cover.

Note: Discard any other wires that are included

with the chest pulse sensor.

If you purchase the optional chest pulse sensor (see page 18), follow the step below to install the receiv-

er included with the chest pulse sensor.

ires

Antenna

Battery

Cover

Attach

receiver

here

HOW TO USE THE ELLIPTICAL EXERCISER

HOW TO MOVE THE ELLIPTICAL EXERCISER

Due to the size and weight of the elliptical exercis-

r, moving it requires two persons. Stand in front of

the elliptical exerciser, hold the upright, and place one

foot against one of the wheels. Pull on the upright and

have a second person lift the rear stabilizer until the

elliptical exerciser will roll on the wheels. Carefully

move the elliptical exerciser to the desired location,

and then lower it to the floor.

HOW TO EXERCISE ON THE ELLIPTICAL

XERCISER

o mount the elliptical exerciser, hold the upper body

arms and step onto the pedal that is in the lower posi-

tion. Then, step onto the other pedal. Push the pedals

until they begin to move with a continuous motion.

Note: The pedal discs can turn in either direction.

It is recommended that you turn the pedal discs in

the direction shown by the arrow; however, for

variety, you can turn the pedal discs in the oppo-

site direction.

To dismount the elliptical exerciser, wait until the ped-

als come to a complete stop. Note: The elliptical

exerciser does not have a free wheel; the pedals

will continue to move until the flywheel stops.

When the pedals are stationary, step off the higher

pedal first. Then, step off the lower pedal.

Pedals

Pedal Disc

Upper Body

Arm

Place

your foot

here

Pull on the

upright

Lift here

CONSOLE FEATURES

This console offers an array of features designed to

make your workouts more effective and enjoyable.

When you use the manual mode of the console, you

can change the resistance of the pedals with the touch

of a button. As you exercise, the console will provide

continuous exercise feedback. You can even measure

your heart rate using the handgrip pulse sensor or the

optional chest pulse sensor.

The console also features eight preset workouts that

automatically change the resistance of the pedals and

prompt you to vary your pedaling pace while guiding

you through an effective workout.

You can even connect your MP3 player or CD player

to the console sound system and listen to your favorite

music or audio books while you exercise.

To use the manual mode, see page 15. To use a

preset workout, see page 17. To use the sound

system, see page 18.

Note: If there is a sheet of clear plastic on the console,

remove the plastic. Make sure that batteries are

installed in the console or that the optional AC adapter

is properly connected (see step 5 on page 8).

CONSOLE DIAGRAM

Audio Jack

HOW TO USE THE MANUAL MODE

1. Press any button on the console or begin

edaling to turn on the console.

hen you turn on the console, the display and the

target pacer will light. A tone will sound and the

console will be ready for use.

2. Select the manual mode.

When you turn on the console, the manual mode

will be selected. If you have selected a workout,

reselect the manual mode by pressing any of the

Quick Resistance/Pace Workouts buttons repeat-

edly until a track appears in the left side of the dis-

play.

3. Begin pedaling and change the resistance of

the pedals as desired.

As you pedal, change

the resistance of the

pedals by pressing the

Quick Resistance but-

tons. Note: After you

press the buttons, it

will take a moment for the pedals to reach the

selected resistance level.

4. Follow your progress with the displays.

Upper right display—

his display can show

the elapsed time, the

pproximate number of

calories you have

burned, and the dis-

tance (total number of revolutions) you have ped-

aled. The display will change modes every few

seconds.

Lower right display—

This display will show

your pedaling pace in

revolutions per minute

(rpm) and the resis-

tance level of the ped-

als. The display will change modes every few sec-

onds.

This display will also show your heart rate when

you use the handgrip pulse sensor or the optional

chest pulse sensor (see step 5 on page 16).

The left display will

show a track repre-

senting 1/4 mile (640

revolutions). As you

exercise, indicators will

appear in succession

around the track until

the entire track

appears. The track will then disappear and the

indicators will again begin to appear in succession.

5. Measure your heart rate if desired.

You can measure your heart rate using either the

andgrip pulse sensor or the optional chest pulse

sensor (see page 18 for information about the

ptional chest pulse sensor). Note: If you hold

the handgrip pulse sensor and wear the chest

pulse sensor at the same time, the console will

not display your heart rate accurately.

If there are sheets

of clear plastic on

the metal contacts

on the handgrip

pulse sensor,

remove the plas-

tic. In addition,

make sure that

your hands are

clean. To measure

your heart rate,

hold the handgrip pulse sensor with your palms

resting against the metal contacts. Avoid moving

your hands or gripping the contacts tightly.

When your pulse is detected, a heart-shaped sym-

bol will flash in the display and then your heart

rate will be shown. For the most accurate heart

rate reading, hold the contacts for at least 15 sec-

onds.

If your heart rate is not shown, make sure that

your hands are positioned as described. Be care-

ful not to move your hands excessively or to

queeze the metal contacts tightly. For optimal

performance, clean the metal contacts using a soft

loth; never use alcohol, abrasives, or chemi-

cals to clean the contacts.

6. When you are finished exercising, the console

will turn off automatically.

If the pedals do not move for several seconds, a

series of tones will sound and the console will

pause.

If the pedals do not move for about five minutes,

the console will turn off and the displays will be

reset.

Contacts

HOW TO USE A PRESET WORKOUT

1. Press any button on the console or begin

edaling to turn on the console.

ee step 1 on page 15.

2. Select a preset workout.

To select a preset workout, press one of the eight

Quick Resistance/Pace Workouts buttons. When

you select a preset workout, the name of the work-

out and the maximum resistance level will appear

in the display for a few seconds. A profile of the

resistance levels of the workout will also scroll

across the left side of the display.

3. Begin pedaling to start the workout.

Each workout is divided into 30 one-minute seg-

ments. One resistance level and one target pace

setting is programmed for each segment. Note:

The same resistance level and/or target pace set-

ting may be programmed for consecutive seg-

ments.

During the workout, the workout profile will show

your progress (see the drawing above). The flash-

ing column of the profile represents the current

segment of the workout. The height of the flashing

column indicates the resistance level for the cur-

rent segment. At the end of each segment of the

workout, a series of tones will sound and the next

segment of the profile will begin to flash. If a differ-

ent resistance level is programmed for the next

segment, the resistance level will appear in the

display for a few seconds to alert you. The resis-

tance of the pedals will then change.

During the workout, the target pacer will prompt

you to keep your pedaling pace near the target

pace setting for the current segment. When a left

ndicator lights, increase your pace; when a right

indicator lights, decrease your pace. When the

enter indicator lights, maintain your current pace.

IMPORTANT: The target pacer is intended only

to provide a goal. Make sure to pedal at a pace

that is comfortable for you.

If the resistance level for the current segment is

too high or too low, you can manually override the

resistance level by pressing the Quick Resistance

buttons. However, when the current segment

ends, the resistance of the pedals will automatical-

ly adjust to the resistance level for the next seg-

ment.

If you stop pedaling for several seconds, a series

of tones will sound and the workout will pause. To

restart the workout, simply resume pedaling. The

workout will continue until the last segment of the

profile ends.

4. Follow your progress with the displays.

See step 4 on page 15.

5. Measure your heart rate if desired.

See step 5 on page 16.

6. When you are finished exercising, the console

will turn off automatically.

See step 6 on page 16.

Profile

HOW TO USE THE SOUND SYSTEM

To play music or audio books through the console

ound system while you exercise, plug the audio cable

into the jack on the console and into a jack on your

P3 player or CD player; make sure that the audio

cable is fully plugged in.

Next, press the play button on your MP3 player or CD

player. Adjust the volume level using the volume con-

trol on your MP3 player or CD player.

THE OPTIONAL CHEST PULSE SENSOR

The optional chest pulse sensor provides hands-free

peration and continuously monitors your heart rate

during your workouts. To purchase the optional

hest pulse sensor, see the front cover of this

manual.

Inspect and tighten all parts of the elliptical exerciser

regularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and

a small amount of mild detergent. IMPORTANT: Keep

liquids away from the console and keep the con-

sole out of direct sunlight. During storage, remove

the batteries from the console.

CONSOLE TROUBLESHOOTING

If the console display becomes dim, the batteries

should be replaced. See assembly step 5 on page 8.

If the handgrip pulse sensor does not function proper-

ly, see step 5 on page 16.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the

reed switch may need to be adjusted.

To adjust the reed switch, you must remove the pedal

springs, the right pedal disc, and the shields.

First, see steps 12 and 11 on page 11 and remove the

Pedal Springs (11). Next, remove the four Screws (51)

from the right Pedal Disc (15), and remove the Pedal

Disc.

Remove all Screws (52, 64) from the Right Shield (4)

and the two Screws (77) from beneath the Pedal Disc,

and then remove the Right Shield. Then, remove all

Screws (52) from the Left Shield (3) and remove the

Left Shield.

Next, locate the Reed Switch (53). Loosen, but do not

remove, the indicated M4 x 16mm Screw (52). Slide

the Reed Switch slightly toward or away from the

Magnet (58) on the flywheel, and then retighten the

Screw. Turn the left Pedal Disc (15) for a moment.

Repeat until the console displays correct feedback.

When the Reed Switch (53) is correctly adjusted, reat-

tach the shields, the right pedal disc, and the pedal

springs.

MAINTENANCE AND TROUBLESHOOTING

HOW TO ADJUST THE DRIVE BELT

If you can feel the pedals slip while you are pedaling,

ven when the resistance is adjusted to the highest

level, the drive belt may need to be adjusted.

To adjust the drive belt, you must first remove both

shields. See HOW TO ADJUST THE REED SWITCH

on page 19 and remove the shields.

Next, loosen the M8 x 22mm Flat Head Bolt (68) and

turn the M10 x 60mm Screw (62) until the Drive Belt

(19) is tight.

When the Drive Belt (19) is tight, tighten the Flat Head

Bolt (68). Reattach the shields.

Page is loading ...

Pro-Form PFEVEL73908 User manual

Brand: Pro-Form

Model: PFEVEL73908

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

Download PDF

report

Pro-Form PFEVEL73908 User manual

This manual is also suitable for

Pro-Form PFEVEL73908 User manual

Related papers

Other documents