Digital Watchdog DWC-MBH2i4WV User manual

Brand: Digital Watchdog

Model: DWC-MBH2i4WV

Category: Security cameras

Type: User manual

Before installing or operating the camera, please read and follow this manual carefully.

DWC-MBH2i4WV

MEGApix® Bullet Camera

04/16

PRECAUTIONS

 Do not open or modify.

 Do not open the case except during maintenance and installation, for it may be dangerous and can cause

damages.

 Do not put objects into the unit.

 Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or

other damages.

 Be careful when handling the unit.

 To prevent damages, do not drop the camera or subject it to shock or vibration.

 Do not install near electric or magnetic fields.

 Protect the camera from humidity and dust.

 Protect the camera from high temperature.

 Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to high

levels.

 Cleaning: To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.

 Mounting Surface: The material of the mounting surface must be strong enough to support the camera.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC rules. These limits are designed to provide reasonable protection against harmful interference, when the

equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency

energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference

to radio communications.

WARNING: Changes or modifications are not expressly approved by the manufacturer.

FCC COMPLIANCE

TABLE OF CONTENTS*

Introduction.......................................................................................................................................................4

Features........................................................................................................................................................4

Parts .............................................................................................................................................................5

Dimensions...................................................................................................................................................6

Inside the Box...............................................................................................................................................7

Installation.........................................................................................................................................................8

Network Connection ....................................................................................................................................8

Before Installation .......................................................................................................................................9

Installation..................................................................................................................................................10

MEGApix® 1080p™ Camera Setup..............................................................................................................11

Installing DW IP Finder™ .........................................................................................................................11

Using DW IP Finder™ ..........................................................................................................................12-14

Network Options.........................................................................................................................................15

Camera Reboot..........................................................................................................................................16

MEGApix® 1080p™ Camera Web Viewer....................................................................................................17

Accessing the Camera’s Web Viewer.......................................................................................................17

GUI Description .........................................................................................................................................18

First & Second Stream...............................................................................................................................19

MEGApix® 1080p™ Camera Setup..............................................................................................................20

Local Configuration ..................................................................................................................................20

Basic > System Settings.......................................................................................................................21-23

Basic > Network Settings .....................................................................................................................24-26

Basic > Stream Settings ......................................................................................................................27-28

Basic > Image Settings ........................................................................................................................29-32

Basic > Security .........................................................................................................................................33

Advanced > Image ....................................................................................................................................34

Advances > Security ............................................................................................................................35-38

Advanced > Basic Event ......................................................................................................................39-43

Specifications ...........................................................................................................................................44-45

Troubleshooting .......................................................................................................................................46-49

Warranty.......................................................................................................................

...................................50

Limits & Exclusions.......................................................................................................................................51

 1/3” CMOS Image Sensor

 Real-time 2.1MP Resolution, 1080P at 30fps

 Dual Codecs (H.264, MJPEG) with Simultaneous Streaming

 4.0mm Fixed Lens

 Smart IR™ with Intelligent Camera Sync. 100ft Range

 Smart DNR™ 3D Digital Noise Reduction

 Digital Wide Dynamic Range (DWDR)

 True Day/Night Mechanical IR Cut Filter

 Auto Gain Control (AGC)

 Back Light Compensation (BLC)

 Auto White Balance (AWB)

 Programmable Privacy Zones

 Motion Detection

 Web Server Built-in

 PoE and DC12V

 OnVIF Compliant, Profile S

 IP66 Certified (Weather Resistant)

FEATURES*

PARTS & DESCRIPTIONS*

No. Description

Description

1 Mounting Base 4 Lens

2 Back Box 5 Sun Shield

3 Front Box

DIMENSIONS*

The following items are included with the MEGApix® 1080p™ camera.

INSIDE THE BOX *

DrillTemplate

HoleA:forca blesroutedthroughtheceil ing

screwhole1:forMountingBase

Mounting Template

There are two ways to power a MEGApix® 1080p™

camera.

Use a PoE-enabled switch to connect data and power through a single

cable to begin viewing and recording images instantly. A non-PoE switch

will require an adaptor for power transmission.

1. Using a PoE-Enabled Switch

The MEGApix® 1080p™ Camera is PoE-Compliant, allowing transmission of power and data

via a single Ethernet cable. PoE eliminates the need for the different cables used to power,

record, or control the camera. Follow the illustration below to connect the camera to a PoE-

enabled switch using an Ethernet cable.

2. Using 12VDC

If a PoE injector is not available, use a power adaptor for power transmission and a non-PoE

switch for data transmission. Follow the illustrations below to connect the camera without a PoE

Injector.

NETWORK CONNECTION*

 Make sure the device in the package is in good condition and all the assembly parts are

included.

 The standard power supply is 12V DC, please make sure your power supply matches with

your camera.

 Make sure all the related equipment is power-off during the installation.

 Check the specification of the products for the installation environment.

 Make sure that the wall is strong enough to withstand four times the weight of the camera

and the bracket.

 For the camera that supports IR, you are required to pay attention to the following

precautions to prevent IR reflection:

 Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome

cover film until the installation is finished. If there is dust or grease on the dome cover,

clean the dome cover with clean soft cloth and isopropyl alcohol.

 Make sure that there is no reflective surface too close to the camera lens. The IR light from

the camera may reflect back into the lens causing reflection.

 The foam ring around the lens must be seated flush against the inner surface of the bubble

to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the

foam ring and the dome cover are attached seamlessly.

INSTALLATION*

Before Starting the Installation

1. Use the mounting plate or camera itself to mark and

drill the necessary holes in the mounting surface.

2. Pull wires through and make connections.*

3. Adjust the camera’s tilting angles to adjust the

camera’s view. See the next page for more information.

INSTALLATION*

Installing the Camera

* NOTE: If necessary, you can route cables through the side opening on the camera’s side

1. Loosen the adjustable nut.

2. Adjust the pan direction [0°~360°].

3. Adjust the tilt direction [0°~90°].

4. Rotate the camera [0~360°] to adjust the lens to the

surveillance angle.

5. Tighten the adjustable nut to complete

the installation.

Installing the Camera’s Angle

Installing DW IP Finder™ Software

DW IP Finder™ searches for all available Digital Watchdog devices

currently connected to your network.

1. Install DW IP Finder to find the MEGApix® 1080p™ camera on your local network. The

software can be found on the included User Manual CD. Run DW IP Finder and install onto

your PC.

2. When setup is complete, launch DW IP Finder.

3. The software will automatically search your network for all Digital Watchdog® supported

devices. Your camera will appear as ”DWC-MBH2i4WV.”

4. Double-click on the camera name and select ‘View Camera Website’ to launch the camera’

web viewer.

*Install the DW IP Finder to a computer located on the same Subnet Mask as the MEGApix®

1080p™ camera.

DW IP Finder™ *

Using DW IP Finder™ Software

Use DW IP Finder™ to change the basic settings of your MEGApix®

1080p™ camera, update firmware for multiple cameras simultaneously

or connect to your MEGApix® 1080p™ camera.

DW IP Finder™ *

*If you change the camera’s IP, write down the camera’s MAC Address for identification in the future.

DW IP Finder™ *

Using IP Finder Software

Use IP Finder to set the connection type and the IP address information

for your MEGApix® 1080p™ camera.

1. DHCP: Select DHCP to access the camera within the same internal network. For further

explanation on DHCP, please see page 16.

2. Static IP: Select Static to connect to the camera from an external network. For further

explanation on Static, please see page 16.

DHCP

The Dynamic Host Configuration Protocol (DHCP) is a network configuration protocol that allows a

device to configure automatically according to the network it is connected to.

If your network supports DHCP and your MEGApix® 1080p™ camera is set to DHCP, IP Finder

will automatically find and set your MEGApix® 1080p™ camera to correspond with your network

requirements.

Static

Static IP addresses are recommended when using a network that does not support DHCP or when

setting your device to be accessed externally via the internet. If Static is selected, you must

manually enter the correct network settings for your MEGApix® 1080p™ camera. The settings will

correspond with your network. To set your camera to a static IP address, we recommend that you

(1) setup the camera to DHCP, (2) allow it to configure itself according to your network, and (3)

change the settings to a static IP address.

1. To set your MEGApix® 1080p™ camera to Static, highlight the desired device from the

search results list, and click on Configuration. In the “Network Configuration” window, make

sure Static is selected.

2. Enter the following information: IP Address, Netmask, Gateway, and Preferred DNS.

3. Click Apply and Reboot to save all changes.

DW IP Finder™ *

Upgrading Cameras using the DW IP Finder

Use the DW IP Finder™ to perform firmware upgrade to all your

MEGApix® 1080p™ cameras from one convenient location.

1. Press the ‘Firmware’ button.

2. In the Firmware Upload section, browse and select the appropriate firmware file to use.

3. Select all the cameras you would like to upgrade. You can select multiple cameras by clicking

on multiple camera models while holding down the Ctrl button*.

4. Click ‘Update Cameras’.

5. The system will indicate if the upgrade was successful or not for each camera.

6. When all cameras have been upgraded, restart the cameras to apply the new firmware.

7. Allow up to 60 seconds for the cameras to reboot and press the ‘Search’ button. If the

cameras reappear in the IP Finder the reboot is complete and the camera is ready.

DW IP Finder™ *

Resetting the Camera

Press RESET about 10s when the camera is powering on or rebooting to

restore the default settings, including the user name, password, IP

address, port No., etc.

The following are the default network settings.

CAMERA REBOOT*

IP Mode DHCP

IP Address 169.254.X.X

Subnet Mask 255.255.255.0

Gateway 169.254.X.X

HTTP Port 80

RTSP Port 554

* Frequent use may cause system error.

Remote Video Monitoring Via Internet Explorer

Monitor and configure the MEGApix® 1080p™ camera through a built-in

web viewer.

1. Type the IP address of the camera in an Internet Explorer window.

Enter Username and Password (Default: Username: admin | Password: admin)

2. The web browser may ask to install the camera’s plug-in in order to view video. Once it has

been installed, Internet Explorer will display video images from the camera.

System Requirements:

• Operating System: Microsoft Windows XP SP1 and above / Vista / Win7 / Server 2003 / Server

2008 32bits

• CPU: Intel Pentium IV 3.0 GHz or higher

• RAM: 1G or higher

• Display: 1024×768 resolution or higher

• Web Browser:

Internet Explorer 6.0 and above

Apple Safari 5.02 and above

Mozilla Firefox 3.5 and above

Google Chrome8 and above

WEBVIEWER*

* The camera currently does not support 64-bit Google Chrome view.

WEBVIEWER*

GUI Description

Monitor and configure the MEGApix® 1080p™ camera through a built-in

web viewer.

1. Live video display- This is the region for live video stream from the camera.

2. Setup- Setup the camera’s Video, Network, Events, System etc.

3. Stream Selection- Select a stream to display it in the viewing area.

4. Full Screen- Expand the camera’s view into full screen. To exit full screen view, press the Esc

button.

5. Menu options such as PTZ will be disabled for cameras that do not support those functions.

Video Display

Setup Menu

Stream Selection

Full Screen View

First Stream & Second Stream

Configure up to two (2) stream settings for monitoring and recording.

On the main monitoring page, user can view the camera with the First Stream settings or

secondary Stream settings. The camera supports the setup of up to two (2) different streams with

different resolution, and FPS for maximum network control. Select which stream to view in the

camera’s main menu by selecting one of the options from the drop-down menu. Streams that are

not enabled in the Streams Setup page will not appear in the drop-down menu.

For Setup Stream Settings, refer to page 27.

WEBVIEWER*

Stream Selection

WEBVIEWER*

SETUP > LOCAL CONFIGURATION

Setup the camera’s Protocol and Live Performance Options.

Protocol: On this page, you can update the camera’s streaming protocol. By default, the camera is

set to TCP.

• TCP: Ensures complete delivery of streaming data and better video quality. Real-time transmission

may be affected.

• UDP: Provides real-time audio and video streams.

• MULTICAST: Select this option when ‘Enable Multicast Discovery’ is checked in the Network setup

page. See page 25 for more information.

• HTTP: Allows the same quality as of TCP without setting a specific ports for streaming under some

network environments.

• Live View Performance: You can adjust the live streaming from the camera. Select between the

shortest delay or Auto. If auto is selected, buffering may occur when the network bandwidth is

limited.

Page is loading ...

Digital Watchdog DWC-MBH2i4WV User manual

Brand: Digital Watchdog

Model: DWC-MBH2i4WV

Category: Security cameras

Type: User manual

Download PDF

report

Digital Watchdog DWC-MBH2i4WV User manual

Digital Watchdog DWC-MBH2i4WV User manual

Related papers

Other documents