Electrolux EM20W100 User manual

Page is loading ...

www.electrolux.com2

CONTENTS

1. IMPORTANT SAFEGUARDS.............................................................................3

2. TECHNICAL SPECIFICATION...........................................................................4

3. INSTALLING INSTRUCTIONS.......................................................................... 4

4. OPERATION INSTRUCTIONS.......................................................................... 6

5.

COMBINATION BUTTON AND FUNCTIONS...................................................10

6. TROUBLE SHOOTING.....................................................................................10

7. MAINTENANCE................................................................................................11

1. IMPORTANT SAFEGUARDS

When using an electrical appliance, basic

safety precautions should always be

observed, including the following:

READ ALL INSTRUCTIONS BEFORE

USING

ENGLISH 3

WARNING!

To reduce the risk of fire, electrical

shock, or injury to person:

WARNING!

In order to avoid overheating do

not cover the heater.

1. The product is for household use only.

2. Connect the appliance to single-phase

AC supply of the voltage specified on the

rating plate.

3. The symbol meaning is “DO NOT

COVER”.

4. The symbol meaning is “DO NOT

INSERT FINGER IN”.

5. The symbol meaning is “CAUTION

HIGH TEMPERATURE”.

6. Never leave the heater unattended

while it is in use. Always turn the product

to the OFF position and unplug it from

the electrical outlet when not in use.

7. Extreme caution is necessary when

any heater is used by or near children,

invalids or elderly person and whenever

the heater is left operating and unattend-

ed. Keep children away from the heater

when it is on

8. The heater must not be located

immediately below an electrical

socket-outlet.

9. Do not run cord under carpeting and

do not cover cord with throw rugs,

runners or the like. Arrange cord away

from traffic area and where it will not be

tripped over.

10. Do not operate the heater with a

damaged cord or plug, or after the heater

malfunctions, has been dropped, or

damaged in any manner.

11. If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or a similarly qualified

person in order to avoid a hazard.

12. Avoid the use of an extension cord

as this may overheat and cause a risk of

fire.

13. Use the heater in a well-ventilated

area. Do not insert or allow objects to

enter any ventilation or exhaust opening.

To prevent a possible fire, do not block

air intakes or exhaust openings in any

manner. Do not use on soft surfaces, like

a bed, where openings may become

blocked. Use the heater on flat, dry

surfaces only.

14. Do not place this heater near

flammable materials, surfaces or

substances, as there may be a risk of

fire. Keep the above flammable materi-

als, surfaces or substances at least 1m

from the front of the product and keep

them away from the sides and rear.

15. Do not use the heater in any areas

where petrol, paint or other flammable

liquids are stored e.g. Garages or

workshops as a hot

16. Don’t use this heater in the

immediate surroundings of a bath, a

shower or a swimming pool.Never locate

the heater where it may fall into bathtub

or other water container.

17. This heater is hot when in use. To

avoid burns and personal injury, do not

touch hot surfaces.

18. Make sure that no other appliances

are plugged in the same electrical socket

as this may cause overload.

19. This product is also designed as a

heater for wall mounting not at high level.

20. Children of less than 3 years should

be kept away unless continuously

supervised .Children aged from 3 years

and less than 8 years shall only switch

on/off the appliance provided that it has

been placed or installed in its intended

normal operating position and they have

been given supervision or instruction

concerning use of the appliance in a safe

way and understand the hazards

involved. Children aged from 3 years and

less than 8 years shall not plug in,

www.electrolux.com4

regulate and clean the appliance or

perform user maintenance.

21. CAUTION--Some parts of this

product can become very hot and cause

burns. Particular attention has to be

given where children and vulnerable

people are present.

22. This appliance can be used by and

persons with reduced physical, sensory

or mental capabilities or lack of children

aged from 8 years and above experience

and knowledge if they have been given

supervision or instruction concerning use

of the appliance in a safe way and

understand the hazards involved.

Children shall not play with the

appliance. Cleaning and user mainte-

nance shall not be made by children

without supervision.

PLEASE SAVE THESE INSTRUCTIONS

2. TECHNICAL SPECIFICATION

3. INSTALLING INSTRUCTIONS

Model

Rated Voltage/

Frequency

220-240V/50HzEM40W060, EG40W060

Rated Power

Proposal Room Size

for Better Result

600W

220-240V/50Hz

EM40W080, EM20W080,

EG40W080, EG20W080

800W

220-240V/50Hz

EM40W100, EM20W100,

EG40W100, EG20W100

1000W

220-240V/50Hz

6M

2

to 10M

2

8M

2

to 14M

2

10M

2

to 16M

2

15M

2

to 26M

2

EM40W150, EG40W150 1500W

Note: This unit is for FLOOR USE or

WALL MOUNTING USE ONLY

A: Feet Installation

WARNING: Do not operate without feet

attached or wall mounted. To operate the

heater only in upright position (feet on

the bottom or control panel on top left

side), any other position could create a

hazardous situation.

This heater can be used with feet

attached or wall mounted, If you use the

product on floor, it must be attached with

feet before operating the unit. You can

assemble as below:

2. Put the product on a suitable position,

use hex wrench to fix the feet with screw

like figure B.

Figure A

1. Unpack and take out the product, take

away the rubber plug like figure A.

WARNING: Do not install this product

vertically, or it will stop work or cause risk

of fire. Install product as figure

A,B,C,D,E

Note: Feet is not included in product

packaging, user need to buy feet as

accessory.

ENGLISH 5

B: Wall mounting Installation

1. Drill 4 holes which diameter is 8mm at

position like figure A, then install the wall

plug into 4 holes.

3. After feet installed, put the product

upright on the floor like figure C, then you

can begin to operate the product.

Note: Be careful that do not install the

feet in wrong direction, please make sure

the short side is in front side of product.

2. Fix the bracket 1 on the wall with

screws like figure B.

3. Install the bracket 2 on bracket 1 with

screw and then fix the bracket like figure

C.

4. When installed the bracket, put the

rubber case into the end of bracket 2 to

protect bracket scratch product. See

figure D

Wrong

Correct

Figure B

Figure C

Figure A

www.electrolux.com6

4. OPERATION INSTRUCTIONS

5. After finish the installation of bracket,

align the holes on back of product and

make the bracket 1 into product, then

Note: When you want to disassemble the

heater, you can operating by moving to

opposite directions from installation.

4.1 Control Panel

Remote Control

Figure D

Figure E

move product leftwards to fix the product.

See figure E.

°C

P

INCREASE

DECREASE

Temp

PROGRAM MENU

Timer

On/Off (stand by)

Working indicator

°C

P

ENGLISH 7

Before using the heater make sure that it

is on a flat and stable surface. The

heater must be connected to a an

appropriate electrical outlet.

Keep loose clothing or bedding, furniture

and flammable material away from the

wall outlet where the heater plug is fitted

in.

First you need set the mechanic button

“POWER” to ON by pressing the button

on left back side of heater, then you

press ON/OFF switch to start to

operate the unit according to your own

desire.

Note: The display will be off without

operation for 120 seconds while unit is

working.

Note: Current time(Hour/Minutes)need to

be set before entering into

MODE(Home/Office/Cabin) by pressing

timer button , then user can start the

current date and time setting according

to below steps:

Note: If 7seconds no operation, program

will back to initial value and setting is

ineffective. Only when Hour and Minute

have been confirmed can the setting be

effective.

User must remove the insulating paper

which covered on battery before using

remote control, please follow below

instructions:

1. Remove the battery bracket from back

of remote control like picture A.

A

Note: This heater

equiped with remote

control which user can

operate the unit

according same step of

control panel

After finishing the setting of hour,

program will automatically enter into

minute setting, 30 and will flash,

user can set minute by pressing

and , digit on display will show from

01, 02,03….to 59. When finish the

setting, press timer setting button to

finish all the setting to enter normal mode

and then you can operate the unit as

normal (display will keep blinking for 7s if

no operation).

User can set up current hour by pressing

timer button, then 23 and symbol

will blink on display, user can set time by

pressing and , digit on display

4.1.1 Hour setting

4.1.2 Minute setting

4.2 Remote Control

°C

P

: Increase the value of temperature

or timer

: Decrease the value of temperature

or timer

: Program menu:

HOME/OFFICE/CABIN

: Temperature, press this button can

lead you to temperature setting

: Timer, press this button can lead

you to temperature setting

: ON/OFF. To start ot shut down the

unit.

P

°C

will show from 00, 01,02….to 23. When

finish the setting, press timer setting

button to enter minute setting

(display will keep blinking for 7s if no

operation)

www.electrolux.com8

B

C

2. Remove the insulating paper that

covered battery like picture B

3. Insert the battery bracket into remote

control like picture C

2. Timing Start: User can also book the

time to start the unit automatically

according following step:

When the unit is in standby state, user

can set the timer to start the unit

according to same step with timing

shutdown.

Note: Please use this remote control

within 6 mters distance, please make

sure the control angle within 30 dgrees.

Note: If you switch to other modes

(HOME/OFFICE/CABIN), the timer

setting will be cleared automatically.

Note: Current date and time need to be

set before using Mode. Please set the

time according above Date/Hour/Minute

setting steps.

1, Timing Shutdown: User can also book

the time to shut down the unit automati-

cally according following step:

When the unit is in working state, long

press timer button for 3 seconds to

enter into shutdown timer setting, digit 00

and will display, user can use

and to select the time that want to

Under normal mode, user can adjust the

temperature according to their own

desire by pressing or button,

temperature will range from 15°C to

36°C.

4.3 Normal Mode Operation

Timer setting:

Defaulted value of high temperature is

23°C, low temperature is 18°C as below:

Note:There are 4 peroids(P1,P2,P3,P4)

in program, the period time is fixed.

P1: 08:00-16:00 18°C

P2: 16:00-23:00 23°C

P3: 23:00-06:00 18°C

P4: 06:00-08:00 23°C

The defaulted temperature will cycle

every day. User can also change current

default tepetature of current period, but it

will come back to default value in next

cycle.(Example: Current time is 9:00,

user can set teperature to 20°C, then

temperature will stay in 20°C from 9:00

to 16:00, next day it will back to 18°C).

4.4.1 Home Mode Setting:

shut down the unit, time will range from

00, 01, 02 to 23 (ie. 02 stand for the unit

will shut down automatically after 2

hours). User can comfirm the setting by

pressing timer button again or

waiting for 3 seconds.

This heater also equipped with 3

intelligent modes HOME/OFFICE/CABIN.

User can select different mode according

to their needs by pressing button .

4.4 Mode Setting:

P

ENGLISH 9

Defaulted value of high temperature is

23°Clow temperature is 18°C as

below:

Note: There are 2 peroids(P1,P2) in

program, the period time is fixed.

P1: 08:00-23:00 23°C

P2: 23:00-08:00 18°C

The defaulted temperature will cycle for

30 days. User can choose the day that

they want to stay in the room. When

cycle finished, the temperature will keep

at 18°C. User can also change current

default tepetature of current period, but it

will come back to default value in next

cycle.

Defaulted value of high temperature is

User can also set the days (1-30 days)

by themselves by long pressing the timer

button for 5s, and then defaulted days 1

begin to flash, you can choose your

wanted days by pressing + or -, When

finished setting, you can confirm by

pressing timer button again or leave it

untouched for 3s.

Days setting:

4.4.2 Office Mode Setting:

4.4.3 Cabin Mode Setting:

23°Clow temperature is 18°C as

below:

Note: There are 4 peroids(P1,P2,P3,P4)

in program, the period time is fixed.

P1: 07:00-12:00 23°C

P2: 12:00-14:00 23°C

P3: 14:00-17:00 23°C

P4: 17:00-07:00 18°C

The defaulted temperature will cycle

every day. User can also change current

default tepetature of current period, but it

will come back to default value in next

cycle.

5. COMBINATION BUTTON AND FUNCTIONS

Child lock

Button Function Operation

Light intensity

Demo mode

Long press button for 5 seconds to lock all program

gfunctions, lock symbol lights on display, long press 5

seconds again to deactivate.

Long press button for 5 seconds, then user can adjust the

intensity of standby light by pressing + or – button, total 3

intensity can be selected.

Long press button for 20 seconds to make heating

elements fail to work, other operations can be operated

normally. Long press 20 s again to deactivate.

This marking indicates that this product

should not be disposed with other

household wastes throughout the EU. To

prevent possible harm to the

environment or human health from

uncontrolled waste disposal, recycle it

responsibly to promote the sustainable

reuse of material resources. To return

your used device, please use the return

Recycling

www.electrolux.com10

°C

P

This product has automatic

shut down function if

temperature decreased by 5

dgrees in 10 minutes

Problem Probable Cause Solution

Short circuit or open circuit

may happened on NTC of

product

Error code E0

will show on

display

Error code E1

or E2 show on

display

User need to restart the product by

pressing standby power button.

User need to send product to

designated

After-sales Service

Agency

to repair, NTC need to be

re-insert and trun on the product

again.

6. TROUBLE SHOOTING

and collection systems or contact the

retailer where the product was

purchased. They can take this product

for environmental safe recycling.

Factory reset

Long press button for 20 seconds to make the product

back to factory setting.

Odor flavour

Generated by heating

element when first time use.

This is normal and will be reduced

gradually during use.

1. Always remove the plug from the

socket-outlet and allow the heater to cool

down before clean it.

2. Wipe the exterior surface of the heater

occasionally with a soft damp cloth (not

dripping wet) and dry the exterior surface

before operating the heater.

WARNING:

Do not immerse the heater in water.

Do not use any cleaning chemicals such

as detergents and abrasives.

Do not allow the interior to get wet as this

could create a hazard.

3. To store away the heater, put the

heater back into its original package and

store it in a clean dry place.

4. In case of malfunction or doubt, do not

try to repair the heater yourself, it may

result in a fire hazard or electric shock.

ENGLISH 11

7. MAINTENANCE

Page is loading ...

www.electrolux.com22

SADRŽAJ

1. VAŽNE MJERE OPREZA.................................................................................23

2. TEHNIČKE SPECIFIKACIJE............................................................................24

3. UPUTE ZA MONTAŽU .....................................................................................24

4. UPUTE ZA UPORABU .....................................................................................26

5.

KOMBINACIJA TIPKE I FUNKCIJA

.................................................................. 30

6. RJEŠAVANJE PROBLEMA..............................................................................30

7. ODRŽAVANJE..................................................................................................31

Page is loading ...

www.electrolux.com42

INHOUD

1. BELANGRIJKE VOORZORGSMAATREGELEN .............................................43

2. TECHNISCHE SPECIFICATIE.........................................................................44

3. INSTALLATIE-INSTRUCTIES..........................................................................44

4. BEDIENINGSINSTRUCTIES ...........................................................................46

5. COMBINATIEKNOP EN FUNCTIES................................................................50

6. PROBLEEMOPLOSSING ................................................................................50

7. ONDERHOUD..................................................................................................51

Page is loading ...

www.electrolux.com52

SISÄLTÖ

1. TÄRKEITÄ SUOJAUSTOIMENPITEITÄ ..........................................................53

2. TEKNISET TIEDOT..........................................................................................54

3. ASENNUSOHJEET..........................................................................................54

4. KÄYTTÖOHJEET.............................................................................................56

5. YHDISTELMÄPAINIKE JA TOIMINNOT..........................................................60

6. VIANMÄÄRITYS...............................................................................................60

7. HUOLTO ..........................................................................................................61

Page is loading ...

www.electrolux.com82

INDICE

1. PROTEZIONI IMPORTANTI ............................................................................83

2. SPECIFICHE TECNICHE.................................................................................84

3. ISTRUZIONI DI INSTALLAZIONE....................................................................84

4. ISTRUZIONI DI FUNZIONAMENTO ................................................................86

5. COMBINAZIONI PULSANTI E FUNZIONI .......................................................90

6. GUIDA ALLA RISOLUZIONE DEI PROBLEMI ................................................90

7. MANUTENZIONE.............................................................................................91

Page is loading ...

www.electrolux.com102

SPIS TREŚCI

1. WAŻNE INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA.........................103

2. DANE TECHNICZNE .....................................................................................104

3. INSTRUKCJA INSTALACJI ...........................................................................104

4. INSTRUKCJA OBSŁUGI................................................................................106

5. KOMBINACJE PRZYCISKÓW I FUNKCJE ...................................................110

6. ROZWIĄZYWANIE PROBLEMÓW................................................................110

7. KONSERWACJA............................................................................................111

Page is loading ...

www.electrolux.com112

VSEBINA

1. POMEMBNI VARNOSTNI UKREPI................................................................113

2. TEHNIČNE ZNAČILNOSTI.............................................................................114

3. NAVODILA ZA NAMESTITEV........................................................................114

4. NAVODILA ZA UPORABO.............................................................................116

5. KOMBINIRANE TIPKE IN FUNKCIJE ...........................................................120

6. ODPRAVLJANJE TEŽAV...............................................................................120

7. VZDRŽEVANJE...............................................................................................121

Page is loading ...

www.electrolux.com/shop

EPH20160125

Electrolux EM20W100 User manual

Electrolux EM20W100 User manual

in other languages

Other documents