Opticon OPI-3301i Quick start guide

Opticon
Brand
Opticon
Model
OPI-3301i
Category
Bar code readers
Type
Quick start guide

This manual is also suitable for

QUICK START GUIDE
CRD-3301B
Power LED
Comm. LEDvv
RS-232C Interface
USB Interface6V Power Input
Power LED Bluetooth LED
Comm. LED
Search Button
For more information, drivers, downloads and more, visit us at:
www.opticonusa.com/start or http://opticon.com/contact-support/
STEP 2 - CONFIGURE WITH THE OPTICON BLUETOOTH SCANNER
Before one or more configuration barcodes can be scanned, the ‘Start config’ barcode has to
be scanned. When done with the configuration, the ‘End config’ barcode has to be scanned.
Start config End config
Set the scanner to default Bluetooth SPP. (This is the communication standard between
scanner and cradle; it does not define the communication standard between cradle and PC)
STEP 3 - SELECT AND CONFIGURE THE INTERFACE CRADLE - PC
First select the physical interface (RS-232 or USB). When RS-232 is used, leave the USB
port unconnected, and then no configurations are required. For USB, you can make a choice
between USB-HID and USB-VCP. For USB-VCP there are two options: no handshaking, and
with handshaking/retries. The no handshake option is faster but less secure.
STEP 4 - MAKE A BLUETOOTH CONNECTION BETWEEN THE SCANNER AND THE CRADLE
Scan the Bluetooth address label on the bottom of the CRD-3301B cradle. The scanner will
then pair with the cradle and connect with it. Once the connection is established, the blue LED
on the cradle will light up continuously. Once the scanner is paired to the cradle the following
barcodes can be used to manually disconnect resp. connect the scanner to the cradle.
USB-HID USB-VCP (No Handshake) USB-VCP (Handshake/retries)
STEP 1 - Connect the power
Make sure that the cradle is powered with a 6V DC adapter and that the red power LED lights up.
The blue Bluetooth LED will start to flash indicating that there is no active Bluetooth connection.
STEP 4 - Make a Bluetooth connection between the scanner and the cradle.
Scan the Bluetooth address label on the bottom of the CRD-3301 cradle. The scanner will then
pair with the cradle and connect with it. Once the connection is established, the blue LED on the
cradle will light up continuously. Once the scanner is paired to the cradle the following barcodes
can be used to disconnect resp. connect the scanner to the cradle.
_+-DISC-+*
Manual Disconnect
_+-CONN-+_
Manual Connect
_SO_
Default Bluetooth SPP
STEP 2 - Configure the scanner.
Set the OPI-3301 to default Bluetooth SPP. (This is the communication standard between
scanner and cradle; it does not define the communication standard between cradle and PC)
_ZZ_
Start
_ZZ_
End
_CNC2_
USB-HID
STEP 3 - Select and configure the interface Cradle - PC.
First select the physical interface (RS232 or USB). When RS232 is used, leave the USB port
unconnected, and then no configurations are required. For USB, you can make a choice between
USB-HID and USB-VCP. For USB-VCP there are two options: with handshaking/retries, and
without handshaking. The no handshake option is faster but less secure.
_CNPC_
USB-VCP (No Handshake)
_CNCR_
USB-VCP (Handshake and retries)
For more information about the CRD-3301, downloads and more, visit us at:
CRD-3301-QUICK START GUIDE
Before one or more configuration barcodes can be scanned, the ‘Start config’ barcode has to be
scanned. When done with the configuration, the ‘End config’ barcode has to be scanned.
www.opticonusa.com/start or
www.opticon.com/service-and-support.aspx
STEP 1 - Connect the power
Make sure that the cradle is powered with a 6V DC adapter and that the red power LED lights up.
The blue Bluetooth LED will start to flash indicating that there is no active Bluetooth connection.
STEP 4 - Make a Bluetooth connection between the scanner and the cradle.
Scan the Bluetooth address label on the bottom of the CRD-3301 cradle. The scanner will then
pair with the cradle and connect with it. Once the connection is established, the blue LED on the
cradle will light up continuously. Once the scanner is paired to the cradle the following barcodes
can be used to disconnect resp. connect the scanner to the cradle.
_+-DISC-+*
Manual Disconnect
_+-CONN-+_
Manual Connect
_SO_
Default Bluetooth SPP
STEP 2 - Configure the scanner.
Set the OPI-3301 to default Bluetooth SPP. (This is the communication standard between
scanner and cradle; it does not define the communication standard between cradle and PC)
_ZZ_
Start
_ZZ_
End
_CNC2_
USB-HID
STEP 3 - Select and configure the interface Cradle - PC.
First select the physical interface (RS232 or USB). When RS232 is used, leave the USB port
unconnected, and then no configurations are required. For USB, you can make a choice between
USB-HID and USB-VCP. For USB-VCP there are two options: with handshaking/retries, and
without handshaking. The no handshake option is faster but less secure.
_CNPC_
USB-VCP (No Handshake)
_CNCR_
USB-VCP (Handshake and retries)
For more information about the CRD-3301, downloads and more, visit us at:
CRD-3301-QUICK START GUIDE
Before one or more configuration barcodes can be scanned, the ‘Start config’ barcode has to be
scanned. When done with the configuration, the ‘End config’ barcode has to be scanned.
www.opticonusa.com/start or
www.opticon.com/service-and-support.aspx
STEP 1 - Connect the power
Make sure that the cradle is powered with a 6V DC adapter and that the red power LED lights up.
The blue Bluetooth LED will start to flash indicating that there is no active Bluetooth connection.
STEP 4 - Make a Bluetooth connection between the scanner and the cradle.
Scan the Bluetooth address label on the bottom of the CRD-3301 cradle. The scanner will then
pair with the cradle and connect with it. Once the connection is established, the blue LED on the
cradle will light up continuously. Once the scanner is paired to the cradle the following barcodes
can be used to disconnect resp. connect the scanner to the cradle.
_+-DISC-+*
Manual Disconnect
_+-CONN-+_
Manual Connect
_SO_
Default Bluetooth SPP
STEP 2 - Configure the scanner.
Set the OPI-3301 to default Bluetooth SPP. (This is the communication standard between
scanner and cradle; it does not define the communication standard between cradle and PC)
_ZZ_
Start
_ZZ_
End
_CNC2_
USB-HID
STEP 3 - Select and configure the interface Cradle - PC.
First select the physical interface (RS232 or USB). When RS232 is used, leave the USB port
unconnected, and then no configurations are required. For USB, you can make a choice between
USB-HID and USB-VCP. For USB-VCP there are two options: with handshaking/retries, and
without handshaking. The no handshake option is faster but less secure.
_CNPC_
USB-VCP (No Handshake)
_CNCR_
USB-VCP (Handshake and retries)
For more information about the CRD-3301, downloads and more, visit us at:
CRD-3301-QUICK START GUIDE
Before one or more configuration barcodes can be scanned, the ‘Start config’ barcode has to be
scanned. When done with the configuration, the ‘End config’ barcode has to be scanned.
www.opticonusa.com/start or
www.opticon.com/service-and-support.aspx
Manual Disconnect Manual Connect
STEP 1 - Connect the power
Make sure that the cradle is powered with a 6V DC adapter and that the red power LED lights up.
The blue Bluetooth LED will start to flash indicating that there is no active Bluetooth connection.
STEP 4 - Make a Bluetooth connection between the scanner and the cradle.
Scan the Bluetooth address label on the bottom of the CRD-3301 cradle. The scanner will then
pair with the cradle and connect with it. Once the connection is established, the blue LED on the
cradle will light up continuously. Once the scanner is paired to the cradle the following barcodes
can be used to disconnect resp. connect the scanner to the cradle.
_+-DISC-+*
Manual Disconnect
_+-CONN-+_
Manual Connect
_SO_
Default Bluetooth SPP
STEP 2 - Configure the scanner.
Set the OPI-3301 to default Bluetooth SPP. (This is the communication standard between
scanner and cradle; it does not define the communication standard between cradle and PC)
_ZZ_
Start
_ZZ_
End
_CNC2_
USB-HID
STEP 3 - Select and configure the interface Cradle - PC.
First select the physical interface (RS232 or USB). When RS232 is used, leave the USB port
unconnected, and then no configurations are required. For USB, you can make a choice between
USB-HID and USB-VCP. For USB-VCP there are two options: with handshaking/retries, and
without handshaking. The no handshake option is faster but less secure.
_CNPC_
USB-VCP (No Handshake)
_CNCR_
USB-VCP (Handshake and retries)
For more information about the CRD-3301, downloads and more, visit us at:
CRD-3301-QUICK START GUIDE
Before one or more configuration barcodes can be scanned, the ‘Start config’ barcode has to be
scanned. When done with the configuration, the ‘End config’ barcode has to be scanned.
www.opticonusa.com/start or
www.opticon.com/service-and-support.aspx
STEP 1 - Connect the power
Make sure that the cradle is powered with a 6V DC adapter and that the red power LED lights up.
The blue Bluetooth LED will start to flash indicating that there is no active Bluetooth connection.
STEP 4 - Make a Bluetooth connection between the scanner and the cradle.
Scan the Bluetooth address label on the bottom of the CRD-3301 cradle. The scanner will then
pair with the cradle and connect with it. Once the connection is established, the blue LED on the
cradle will light up continuously. Once the scanner is paired to the cradle the following barcodes
can be used to disconnect resp. connect the scanner to the cradle.
_+-DISC-+*
Manual Disconnect
_+-CONN-+_
Manual Connect
_SO_
Default Bluetooth SPP
STEP 2 - Configure the scanner.
Set the OPI-3301 to default Bluetooth SPP. (This is the communication standard between
scanner and cradle; it does not define the communication standard between cradle and PC)
_ZZ_
Start
_ZZ_
End
_CNC2_
USB-HID
STEP 3 - Select and configure the interface Cradle - PC.
First select the physical interface (RS232 or USB). When RS232 is used, leave the USB port
unconnected, and then no configurations are required. For USB, you can make a choice between
USB-HID and USB-VCP. For USB-VCP there are two options: with handshaking/retries, and
without handshaking. The no handshake option is faster but less secure.
_CNPC_
USB-VCP (No Handshake)
_CNCR_
USB-VCP (Handshake and retries)
For more information about the CRD-3301, downloads and more, visit us at:
CRD-3301-QUICK START GUIDE
Before one or more configuration barcodes can be scanned, the ‘Start config’ barcode has to be
scanned. When done with the configuration, the ‘End config’ barcode has to be scanned.
www.opticonusa.com/start or
www.opticon.com/service-and-support.aspx
Default Bluetooth SPP
STEP 1 - Connect the power
Make sure that the cradle is powered with a 6V DC adapter and that the red power LED lights up.
The blue Bluetooth LED will start to flash indicating that there is no active Bluetooth connection.
STEP 4 - Make a Bluetooth connection between the scanner and the cradle.
Scan the Bluetooth address label on the bottom of the CRD-3301 cradle. The scanner will then
pair with the cradle and connect with it. Once the connection is established, the blue LED on the
cradle will light up continuously. Once the scanner is paired to the cradle the following barcodes
can be used to disconnect resp. connect the scanner to the cradle.
_+-DISC-+*
Manual Disconnect
_+-CONN-+_
Manual Connect
_SO_
Default Bluetooth SPP
STEP 2 - Configure the scanner.
Set the OPI-3301 to default Bluetooth SPP. (This is the communication standard between
scanner and cradle; it does not define the communication standard between cradle and PC)
_ZZ_
Start
_ZZ_
End
_CNC2_
USB-HID
STEP 3 - Select and configure the interface Cradle - PC.
First select the physical interface (RS232 or USB). When RS232 is used, leave the USB port
unconnected, and then no configurations are required. For USB, you can make a choice between
USB-HID and USB-VCP. For USB-VCP there are two options: with handshaking/retries, and
without handshaking. The no handshake option is faster but less secure.
_CNPC_
USB-VCP (No Handshake)
_CNCR_
USB-VCP (Handshake and retries)
For more information about the CRD-3301, downloads and more, visit us at:
CRD-3301-QUICK START GUIDE
Before one or more configuration barcodes can be scanned, the ‘Start config’ barcode has to be
scanned. When done with the configuration, the ‘End config’ barcode has to be scanned.
www.opticonusa.com/start or
www.opticon.com/service-and-support.aspx
_QSG_CRD-3301B_005
STEP 1 - Connect the power
Make sure that the cradle is powered with a 6V DC adapter and that the red power LED lights up.
The blue Bluetooth LED will start to flash indicating that there is no active Bluetooth connection.
STEP 4 - Make a Bluetooth connection between the scanner and the cradle.
Scan the Bluetooth address label on the bottom of the CRD-3301 cradle. The scanner will then
pair with the cradle and connect with it. Once the connection is established, the blue LED on the
cradle will light up continuously. Once the scanner is paired to the cradle the following barcodes
can be used to disconnect resp. connect the scanner to the cradle.
_+-DISC-+*
Manual Disconnect
_+-CONN-+_
Manual Connect
_SO_
Default Bluetooth SPP
STEP 2 - Configure the scanner.
Set the OPI-3301 to default Bluetooth SPP. (This is the communication standard between
scanner and cradle; it does not define the communication standard between cradle and PC)
_ZZ_
Start
_ZZ_
End
_CNC2_
USB-HID
STEP 3 - Select and configure the interface Cradle - PC.
First select the physical interface (RS232 or USB). When RS232 is used, leave the USB port
unconnected, and then no configurations are required. For USB, you can make a choice between
USB-HID and USB-VCP. For USB-VCP there are two options: with handshaking/retries, and
without handshaking. The no handshake option is faster but less secure.
_CNPC_
USB-VCP (No Handshake)
_CNCR_
USB-VCP (Handshake and retries)
For more information about the CRD-3301, downloads and more, visit us at:
CRD-3301-QUICK START GUIDE
Before one or more configuration barcodes can be scanned, the ‘Start config’ barcode has to be
scanned. When done with the configuration, the ‘End config’ barcode has to be scanned.
www.opticonusa.com/start or
www.opticon.com/service-and-support.aspx
QUICK START INSTRUCTIONS
STEP 1 - CONNECT THE POWER
Make sure that the cradle is powered with a 6V DC adapter and that the red power LED lights
up. The blue Bluetooth LED will start to flash indicating that there is no active
Bluetooth connection.
© Copyright Opticon. All rights reserved. This information is subject to change
without prior notice. For availability, contact your local representative.
  • Page 1 1
  • Page 2 2

Opticon OPI-3301i Quick start guide

Opticon
Brand
Opticon
Model
OPI-3301i
Category
Bar code readers
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents