Artistic License Art-Switch PoE4 User manual

Brand
Artistic License
Model
Art-Switch PoE4
Type
User manual
Art-Switch PoE4 User Guide
(Version 1-2)
Art-Switch PoE4
TM
is a DIN-Rail Ethernet switch. It provides five 10/100BaseT Ethernet
ports, four of which support Power over Ethernet (PoE).
Art-Switch PoE4 is housed in a small robust DIN-Rail case that can also be surface mounted.
All Ethernet connections are made via RJ45's. Each port has individual indicators to show
speed of connection, PoE use and activity.
The input power required is 48V DC and is via an un-pluggable screw terminal connector
(supplied). Art-Switch is capable of auto configuration per port, which includes speed, duplex
and cable type.
The PoE output on the four ports complies with the IEEE802.3af standard. Art-Switch is capable of providing power and data to four other
products in the Art-Range such as Art-Lynx O/P or Art-Relay. It can also be used with any PoE or Ethernet compatible nodes.
Key Features:
5 port Ethernet Switch
10BaseT / 100BaseT, Half / Full-Duplex
IEEE802.3af PoE capable (4 port)
DIN-Rail or surface mount
Art-Net compatible
Individual port speed, activity & PoE indicators
Auto-sensing per port
Auto-uplink detection (cable type)
Power Device (PD) Detection and Classfication
Specification:
Input Voltage: 48V DC
Input Current: 1.5A maximum
Internal Input Fuse: Electronic Resettable Fuse
Input Connector (Power): 2pin Screw Terminal
Input Connector (Data): RJ45
Output Voltage (PoE): 48VDC (complies with IEEE802.3af)
Output Connector: RJ45 (Data & Power)
Max Wire Size: 2.5mm
2
Duty Cycle: 80% @ 25˚C
Dimensions: DIN Rail (W 160mm x H 110mm x D 62mm)
IP: Indoor use only
Listings: CE, FCC
PoE Classification Class 0 to Class 4 supported
Power Supply Options: (order separately)
Art-Switch PoE4 requires 48V DC to operate.
PSU Option
Number of Units
Case Style
PSU-48-1.25-DR
1
DIN-Rail
PSU-48-5-DR
3
DIN-Rail
PSU-48-10-DR
6
DIN-Rail
Note: When connecting a PSU to an Art-Switch care must be taken to ensure the correct cable is used and inductors are fitted close to
the unit if the environment has large switching loads in close proximity.
Copyright © Artistic Licence Engineering Ltd. All rights reserved.
The Product:
Connections
2
Port E
RJ45
4
DC Power
2pin Screw Terminal
13
Port A
RJ45
16
Port B
RJ45
19
Port C
RJ45
22
Port D
RJ45
Indicators
1
Port E Duplex
Green
3
Port E Speed
Yellow
5
Power
Red
6
Port E Activity
Yellow
8
Port A Activity
Green
9
Port B Activity
Green
10
Port C Activity
Green
11
Port D Activity
Green
12
Port A Speed
Green
14
Port A PoE Active
Yellow
15
Port B Speed
Green
17
Port B PoE Active
Yellow
18
Port C Speed
Green
20
Port C PoE Active
Yellow
21
Port D Speed
Green
23
Port D PoE Active
Yellow
Other
7
Ventilation
Must be kept free from obstruction and be in a ventilated area
Operation:
Art-Switch PoE4 is used to connect Ethernet / Art-Net nodes together. It provides data communication and power for up to four devices.
Please refer to the wiring diagram on the opposite page for more information.
All settings are factory configured and Art-Switch PoE4 has been set up as an un-managed Ethernet Switch. There are some settings that
are configured automatically:
Auto-Negogiate: When a new connection is made Art-Switch will auto detect the speed for each port individually. It will always default ot
the highest speed.
Auto Cable Detection: There are two types of Ethernet cables that are used to connect equipment together; Patch and Cross-Over. Art-
Switch has auto cable detection so either type can be used to connect any type of Ethernet device.
Connecting Art-Switch to:
Cable to be used:
Ethernet Switch
Cross-Over Cable
Computer or Node
Patch/Straight Cable
Earthing:
In some circumstances Art-Switch may need to be connected to Mains Earth. Under the top left terminal guard there is a connection to
the Cable Shield that can be connected to Mains Earth.
The Cable Shield is referenced to logic ground by a capacitor / resistor network as specified in the Ethernet standard.
Wiring Diagram
1) Conventional (One controller, four nodes)
This is a standard network configuration. Most networks are based on this
model.
Art-Switch PoE4 provides power and data to each of the four nodes
2) Multiple Switches (No controller, 8 nodes)
Two Ethernet Switches can be
connected together with a
cross over cable to extend the
number of ports.
3) Sub-set of a Network (Multi zone installation)
In big installations there may be a central controller that needs to get to
multiple zones via either standard copper or fibre mediums. Art-Switch
can be used for local switching and power distribution while being
connected to the network backbone.
Mounting Drawing:
Artistic Licence
Studio 1, Spectrum House
32-34 Gordon House Road
London
NW5 1LP
Tel: +44 (0)20 88 63 45 15
Fax: +44 (0)20 84 26 05 51
Email: Sales@ArtisticLicence.com
The information contained in this document is subject to change without notice. Artistic Licence Engineering Ltd. makes no
warranty of any kind with regard to this material, including, but not limited to, the implied warranties of fitness for a particular
purpose.
Artistic Licence Engineering Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance
or use of this material. All trademarks are acknowledged.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Artistic License Art-Switch PoE4 User manual

Brand
Artistic License
Model
Art-Switch PoE4
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents