when activating the Prewash option.
“Time Saver” button
• Enables quicker washing by shortening the
programme duration.
• Recommendable for small loads or only lightly
soiled laundry.
“Cold Wash” button
• Saves energy used for water heating while
maintaining good wash result.
• Recomentable for lightly soiled laundry without
stains.
• Make sure that your detergent is suitable for cold
wash temperatures (15 or 20 °C).
• Mainly selectable on the lowest temperature step
of the programmes.
“Extra Rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helping
people with allergies.
“Spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning
is cancelled but intermediate spin peaks remain
during the rinse. The water is drained out only.
DELAY TIMER
The “Delay Timer” button allows the user to run
the machine at his convenience, for example at night
when electricity is cheaper.
• Do not use liquid detergent when activating this
function.
• Select programme, spin speed and options.
• Press the “Delay Timer” button several times to
delay the start by up to 24 hours.
• Start the programme (see “Progremme
Start”). The indication lamp over the “Delay
Timer” button lights up and goes off when the
programme starts.
• Once having pressed the “Start/Pause” button,
the countdown of the time delay begins. The
time delay indication on the display disappears
when the programme starts and is replaced by the
remaining time.
• After the “Start/Pause” button has been
pressed, the number of hours preselected can
be reduced by pressing again the “Delay Timer”
button.
To cancel the “Delay Timer”
..before you press the “Start/Pause” button:
• Turn the programme selector to another position
or press the “Reset” button.
..after having pressed the “Start/Pause”
button:
• Press the “Reset” button for at least 3 second.
The start delay indicator light goes off.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The blinking light next to the “Start/Pause” button
becomes constant. The programme sequence
indicator shows the current programme phase,
running from left to right through Wash, Rinse, Spin/
Drain. When the programme phrase is finised, the
corresponding indication goes out.
“DOOR LOCKED” INDICATION
After start of a program the lamp lights up to indicate
that the lid can not be opened. As long as a wash
programme is running, the lid remains locked and
must on no account be forced open. In case you
have an urgent need to open it during a running
programme, refer to “Cancel a running programme
before the end”.
1.
PREPARATION OF THE WASH CYCLEPREPARATION OF THE WASH CYCLE
Load the washing machine, close the drum door
and check that it is closed properly.
2. Pour in the detergent and any additives, as
described overleaf and in the instruction manual.
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The time display
shows the duration of the selected programme
(in hours and minutes), and the indicator for the
“Start/Pause” button flashes. The indicator for
the preset spin speed lights up. After the end of
a programme, or when a programme is selected
but not yet started, the washing machine will
therefore switch off automatically after about a
quarter of an hour. To switch the washing machine
on again, turn the programme selector to “Off”
and afterwards to the desired programme again.
SELECT ANY DESIRED OPTION
When the combination of programme and additional
option(s) is not possible, the indication lights switch
off automatically. Unsuitable combinations of options
are deselected automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Tap closed”
No or not sufficient inlet water.
“Service”
Failure or malfunction of an electrical component.
“Clean filter”
Waste water is not pumped out.
Spin speed indication blinks: unbalance during
spinning.
•
PROGRAMME ENDPROGRAMME END
The “Door locked” indication lights off and the
display shows “End”. After about a quarter of
an hour, the washing machine will switch off
completely to save energy.
1. Turn the programme selector to the “Off”
position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry.
1.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme, temperature, any
options and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL A RUNNING PROGRAMME BEFORE THE
END
The “Reset” button cancels a programme before
the end.
• Press the “Reset” button for at least 3 seconds.
The water is drained out; it may last a while until
you can open the lid.
Programme
Tempe-
rature
(°C)
Load
(kg)
Water
(l)
Energy
without “Time
Saver”
(kWh)
Approx. Programme Duration (hrs : min)
%
without “Time Saver” with “Time Saver”
Cotton 90 6.0 55* 1.90 2:00 1:50
57
Cotton 60 6.0 48 1.14 2:30 1:45
Cotton 40 6.0 48 0,64 2:15 1:30
Synthetics 60 3,0 50* 0,90 2:05 1:14
40
Synthetics 40 3,0 40 0,50 1:50 0:59
Mini 30 1,0 25 0,22 0:45 -
Delicates 30 1,5 50 0,50 0:41 -
Wool 40 1,0 40 0,55 0:35 -
Baby 60 4,0 57 0,90 1:45 -
Mix 15’ 30 3,0 30 0,15 0:15 -
Mix 30’ 30 3,0 42 0,25 0:30 -
Mix 60’ 40 3,0 40 0,45 1:00 - 61
Eco Cotton** 60 6.0 48 0,75 3:30 -
53Eco Cotton** 60 3.0 35 0,67 2:50 -
Eco Cotton** 40 3,0 35 0,49 2:05 -
Eco Cotton 20 6.0 48 0,15 2:25 - 53
CONSUMPTION DATA
Power consumption in off-mode 0.11 W / in left-on mode 0.11 W
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer to the
default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
Approximete remaining moisture content (%). After programme end and spinning with maximum selectable spin speed, in default programme setting.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Reference Programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.