Wet Republic 0AH7-11206 Installation guide

PARAGON BATH

SHOWER DOOR/ BATH TUB SCREEN INSTALLATION

I

NST

R

UCT

I

ONS

H7-11206

…………………………………………………………………………………………

Please read these instructions carefully before installing. If you have any

questions regarding installation, please call our technical support specialists

Monday through Friday 9:00 AM – 5:00 PM at Phone: (888) 895-1989, or

e-mail our technical support group at Support@Paragonbath.com. For more

information on Paragon Bath Shower Doors & Tub screens please visit

www.ParagonBath.com

Installing Preparations

1. After opening the carton, please read the instructions carefully, examine

boxes and packages for shipping damage. If the unit has been damaged, has

a finishing defect, or has missing parts, please contact our customer support

department within 3 business days of the delivery date. Please note that

Paragon Bath will not replace any damaged products or missing parts free of

charge after 3 business days or if the product has been installed. Feel free to

contact Paragon Bath if you have any questions.

2. Please note that you should consult your local building codes with

questions on installation compliance standards. Building and plumbing codes

may vary by location; we are not responsible for code compliance standards

for your project and will not accept any returns.

3. If this screen is going to be installed in a new construction, please, install all

of the required plumbing and drainage before installing the shower. Use a

competent and licensed (if required) plumber for all plumbing installation

period.

4. During installing, please make sure the installation surface is level and solid

and will be able to support the total weight of the screen. Also, make sure that

the walls are plumb. Depending on the type of screen you are installing, some

adjustments in leveling may be possible. However, irregular installation,

surface level or out of square conditions can result in serious problems for your

installation. Please note that some adjustments and drilling may be necessary.

Please protect all primary surfaces of the product during installation. Never set

your glass down directly onto a tile floor. Always use a piece of wood or

cardboard to protect the bottom edge and corners of the glass.

5. Please wear labor glasses during installation.

In

sta

ll

at

ion n

ecessary

tools

e

Deta

il

e

d

D

i

a

g

ram

o

f

Show

er

/

Bat

h

t

ub

scree

n

Components

Component list

No.

Name

Q’ty

No.

Name

Q’ty

01

Vertical profile

dustproof cover left

1pc

16

Spring assembly

8pcs

02

Wall profile

dustproof cover left

1pc

17

Glass upper fixed part

1pc

03

Waterproof strips

1pc

18

Glass pad

1pc

04

Magnetic strips

2pcs

19

Screw cover

10pcs

05

Wall profile (with

strips inside)

2pcs

20

Glass connect part

1pcs

06

Vertical profile (with

magnetic strips )

2pcs

21

Gap sealing strip

1pc

07

Decorative profile

2pcs

22

Vertical profile

dustproof cover right

1pc

08

Bottom guide track

1pc

23

Wall profile dustproof

cover right

1pc

09

Upper guide track

1pc

24

Glass bottom fixed part

1pc

10

Profile adjust block

6pcs

25

Bottom block

4pcs

11

Philips head screw

ST4*12

10pcs

26

Inner side moving glass

1pc

12

Wall anchor

6pcs

27

Middle moving glass

1pc

13

Philips head screw

ST4*30

6pcs

28

Stationary glass

1pc

14

Philips head screw

ST4*20

10pcs

29

handle

1pc

15

Screw for profile

adjust block

6pcs

30

Shower base

1pc

WARM TIPS

01:

Open the packaging carefully and inspect all the necessary parts using

detailed diagram and component list in your manual as a reference. Before

discarding the carton, check for small hardware bags that tend to fall to the

bottom of the box. If any parts are damaged or missing, please contact us for

replacement.

02:

Retain these installation instructions for future use if in need.

I

N

ST

A

LL

A

TIO

N

STEPS:

1. Measurement.

Measure the distance between two walls. This

distance is marked as “W”.

Please see image 1 for details:

Fig 1

2. Check the guide track

Your Guide tracks (08&09) has been precut for your shower model width:59”.

If W-width of your wall-to-wall opening is equal to the size of your Shower

model, it is unnecessary to cut the Guide tracks .If W-width of your

wall-to-wall opening is less than the size of your Shower model, you will need

to cut the Guide tracks. upper guide track and bottom guide track both cut

in the same side which close to the moving glass.

The length to cut off will be L= Subtract W from the size of your Shower Model.

Please see Fig 2 and 3 for details:

Fig 2

(Upper guide track to be cut)

Fig 3

(Bottom guide track to be cut)

3. In order to make it easy for following installation of frames, it’s better to

tapping on both sides of the upper and bottom guide tracks. Use Philip’s screw

ST4*20(14) to lock to both ends of upper and bottom guide track, then loosen

the screws.

Please see Fig 4 for details

Fig 4

4. Drilling new holes on bottom guide track

4.1 Determine the hole position on bottom guide track

Please see Fig 5 for details

Fig 5

4.2. Use 1/8” drill bit to drill holes on bottom guide track

P

lease see

Fig

6

f

or de

t

ails

Fig 6

5. Determine shower door location.

5.1. Put the Wall profile (5) to the wall above the shower base and level it

vertically. Mark the drilling holes on the wall through the holes in the Wall

profile.

5.2. Remove the wall profile, use electric drill with 1/4” drill bit to drill holes and

use hammer to drive the Wall anchors (12) into the wall.

Please see Fig 7 for details:

Fig 7

6. Assemble the upper guide track

push the wheel set into track 01 and track 02, and push wheel set buffer

blocks into track 01.

Kindly note: Top guide track comes with gear system and gear strips

assembled.

Please see Fig 8 and Fig 9 for details

Fig 8

Fig 9 ( Inner view of upper

t

rack)

7. Assemble frames

7.1 Use Philips head screw ST4*20(14) to lock the upper and bottom guide

tracks to the vertical profiles(6)

Important note: before assemble frames please make sure the wheel set and

buffer block already install on top guide track. Refer to above Fig 6

Please see Fig 10 for details

Fig 10

7.2 use straight screw driver to lock vertical profile(6) to wall profile(5).

Please see fig 11 for de

t

ails

Fig 11

8. Place the complete frames to the two walls and use Philips head screws

ST4*30(13) to fix the frames to the walls.

Use Philips screw driver to lock spring assembly (16) to the slot with Philips

head screw ST4*12(11)

Please see Fig 12 for details

Fig 12

9. Install stationary glass

9.1. Snap the glass pad (18) into the bottom guide track.

9.2. Snap the glass connect part (20) to the glass and place the stationary

glass (28) to the glass pad, then push the stationary glass into the vertical

profile slowly and gently.

9.3. Use Philips driver to lock the glass fixed parts on upper (17) and bottom

(24) with Philips head screw ST4*12, then fill with screw covers (19).

Please see Fig 13 for details

Fig 13

10. Install middle moving glass

10.1 Please make sure the gear strip is well connected to the profile, and then

make sure the pull riverting screw is installed on the gear strip side.

Please see Fig 14 for de

t

ails

Fig 14

10.2 Place the middle moving glass (27) to the upper guide track slot tipsily

and then adjust it slowly and gently till it is straight to the upper and bottom

guide tracks slot. Later insert the wheel set sheath to the moving glass profile

slot.

Kind remind: For safety consideration, it’s better to use protection on the

angles of bottom glass during this installation.

P ease see F g 15 o de a s

l i f r t il

Fig 15

11. Install inner side moving glass

11.1 Please make sure the inner moving glass pull riverting screw is on the

side of small gear wheel. The big gear wheel is on inner side and the small

gear wheel is on outer side.

Please see Fig 16 for de

t

ails

Fig 16

11.2 Inner side moving glass (26) installation step is same with the installation

step of middle moving glass. For details please refer to 9.2 and Fig 13.

12. Install bottom block

Snap one side of the bottom block (25) to the bottom guide track (8) and

then press the other side down to the profile. Using the Philips driver to lock

the block to the bottom guide track with Philips head screw ST4*12.

P ease see F g 17 o de a s

l i f r t il

Fig 17

13. Install magnetic strips and waterproof strips

Please see Fig 18 for de

t

ails

Fig 18

14. Install gap sealing strip.

All the Paragon bath shower door/tub screens

comes with gap sealing strip(21), its function

is to seal the tiny gap between stationary glass

and aluminum profile. After you install the glass

please insert the rubber to seal it for getting

perfect waterproof result.

Please see Fig 19 for details

Fig19

15. Install handle(29)

Kindly note: Handle set already assembled, you just need to disassemble

during install on glass door and lock every part will be done.

Please see Fig 20 for details

Fig 20

16. Adjustment of inner side moving glass.

Pull the wheel set sheath a little out from the guide track, use Philip’s screw

driver to adjust the high of wheel set sheath until the big gear and the guide

track gear strip get good grip.

Please see Fig 21 for details

Fig 21

17. Adjustment of middle moving glass.

Pull the wheel set sheath a little out from the guide track, use Philip’s screw

driver to adjust the high of wheel set sheath until the small gear and the guide

track gear strip get good grip. Step same as above Fig 21.

Kindly note: If the grip between gear and gear strip is too tight will increase

heavy to open the door. While if the grip between gear and gear strip is too

loose, the moving orders will be upset between inner side moving glass and

middle moving glass. Just to make sure not too tight or too loose.

After adjustment, use Philip’s screws ST4*12 to lock the wheel set sheaths to

the profile of the inner moving glass and middle moving glass, and then fill with

screw cover.

Please see Fig 22 for details.

Fig 22

18. Install decorative profile.

Insert the decorative profile(7) by 40 degree gradient to the opening gap of

vertical profile, make the decorative profile bottom to the same level as vertical

profile, then press the whole decorative profile, the spring set will help to

support and hold it tight inside the vertical profile.

Please see Fig 23 for details

Fig 23

19. Install Vertical profile dustproof cover (1, 22) and wall profile

dustproof cover(2, 23)

Please see Fig 24 for details

Fig 24

20. Apply the sealant along the profiles and guide tracks.

on the seams between the bottom guide track and

the profiles as well as along the shower base.

Please see Fig 25 for details

Fig 25

Product

Maintenance

To ensure long lasting life for your shower door/bath tub screen, please clean

the dust or stains use non-abrasive sprays or cream based cleaners. Never

use abrasive cleansers, metal brushes or scrapers that could scratch or dull

the surface.

To ensure a long lasting hardware finish, wipe off the metal parts after each

use with a soft cloth. Do not use abrasive cleaners or cleaning products

containing ammonia, bleach or acid. If accidentally used, rinse the surface as

soon as possible to prevent finish peeling or corrosion. After cleaning the shiny

finishes, rinse thoroughly and wipe dry with soft cloth. Clean stainless steel

surfaces at least once a week. When applying stainless steel cleaner or polish,

work with (not against/across) the grain. Never use an abrasive sponge or

cloth, steel wool or wired brushes.

Thank you for choosing PARAGON BATH, ”The Art Of Showering”.

WARANTY INFORMATION

This is Paragon Bath LLC exclusive written warranty effective August 8, 2014

This warranty extends only to the original owner/end-user for household use only

and is not transferable to a subsequent owner. This warranty applies only to Paragon

Bath LLC products purchased from an authorized dealer and installed in United States

or Canada. Proof of purchase (original sales receipt) must be provided with all

warranty claims. In no event shall the liability of Paragon Bath LLC exceed the

purchase price of the unit. If Paragon Bath LLC shower & tub doors, shower

enclosures and shower bases are used commercially, Paragon Bath LLC warrants such

products to be free from defects in material and workmanship for one (1) year from

initial date of purchase from an authorized dealer, with all other terms of this

warranty applying except duration Paragon Bath LLC

Paragon Bath LLC warrants that for a period of ten (10) years following from the

initial date of purchase by the owner/end-user, contractor or builder from an

authorized dealer. Paragon Bath LLC Shower Doors are warranted against material

defects and defects in workmanship. All other Shower Door components are

warranted for 10 years from date of sale. All warranty claims are subject to

inspection by Paragon Bath prior to us providing a remedy for the warranty claim.

Paragon Bath LLC hereby disclaims all warranties for products sold as store displays.

Paragon Bath LLC hereby disclaims all warranties for products used outside of the

United States or Canada whether expressed or implied, including but not limited to

the implied warranties of merchantability and fitness for a particular purpose.

Paragon Bath LLC will, at its election, repair, replace with product of equal value or

make appropriate adjustment where Paragon Bath LLC analysis or inspection of

warranty claim discloses any such defects occurring in normal usage within the

warranty period. Paragon Bath LLC warranty obligation shall be discharged upon

tender of replacement or repair. Purchaser’s refusal to accept the tender terminates

warranty obligation.

Cost of freight for returning products to Paragon Bath LLC for repairs or replacement

under this limited warranty are the responsibility of the customer. Cost of freight

associated with shipping of replacement product or parts to the customer may be

charged to customer. Any product replaced or repaired during the warranty period

will be covered only for the remaining period of the original warranty. In no event

will Paragon Bath LLC be liable for costs of repair or replacement of any installation

Page is loading ...

Wet Republic 0AH7-11206 Installation guide

Wet Republic 0AH7-11206 Installation guide

Related papers

Other documents