Kichler Lighting 44344WNWLED User manual

Brand: Kichler Lighting

Model: 44344WNWLED

Type: User manual

IS-44344-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

1) Pass wire through stems[A] and small threaded tubes[B]

and screw stems into couplings[G] on top of xture body[H].

NOTE: Thread locking compound must be applied to all stem

threads as noted with symbol (4) to prevent accidental

rotaon of xture during cleaning,relamping, etc.

2) Pass xture wire through remaining stems and screw stems

together.

3) On one side of xture, pass xture wire through one small

threaded pipe[K]. Screw each small threaded pipe onto top of

stem on each side.

4) On one side of xture, pass xture wires through each hole in

canopy[F]. Lower canopy down towards stems. Pass each hole

in canopy over end of each threaded pipe on top of stems.

5) On one side of xture, pass xture wire through

lockwasher[P]. Thread lockwasher onto end of threaded

pipe protruding from inside canopy. Pass xture wire through

hexnut[Q]. Thread hexnut onto end of threaded pipe.

6) Repeat to other threaded pipe.

7) Aach mounng plate[D] to outlet box[C] using the strap

mounng screws[E]. Mounng strap can be adjusted to suit

posion of xture.

8) Grounding instrucons: (See Illus. a or b).

a) On xtures where mounng strap is provided with a hole

and two raised dimples, wrap ground wire from outlet

box around green ground screw, and thread into hole.

b) On xtures where a cupped washer is provided, aach

ground wire from outlet box under cupped washer and

green ground screw, and thread into mounng strap.

If xture is provided with ground wire, connect xture ground

wire to outlet box ground wire with wire connector (not

provided.) aer following the above steps. Never connect

ground wire to black or white power supply wires.

9) Cut the wire to length for wiring and make wire connecons

to the driver aer stems[A] have been installed per wiring

Diagram “A’ in view above the canopy[F] using supplied wire

nuts[R].

10) Make wire connecon. Reference chart below for correct

connecons and wire accordingly.

Connect Black or Red

Supply Wire to:

Connect White Supply Wire

to:

Black White

*Parallel cord (round &

smooth)

*Parallel cord (square &

ridged)

Clear, Brown, Gold or Black

without Tracer

Clear, Brown, Gold or Black

with Tracer

Insulated wire (other

than green) with copper

conductor

Insulated wire (other than

green) with silver conductor

*Note: When parallel wire (SPT 1 &

SPT 2) are used. The neutral wire

is square shaped or ridged and the

other wire will be round in shape or

smooth (See illus.)

Neutral Wire

11) Push xture to ceiling, carefully passing mounng screws

through holes in canopy. NOTE: Be certain wires do not get

pinched between mounng strap and canopy.

12) Secure xture to ceiling with the four (4) at head machine

screws[L] through the sides of the canopy as shown.

13) Install the six (6) glass spacers[M] with pads on the top as

shown.

14) Carefully install the glass[N] by raising up to the sides and

using the decorave knobs[O] secure the glass into place as

shown.

Installaon Instrucons – Loop/Chain Link Mount

1) Follow steps 1 and 4 from Rigid Stem Mount Instrucons.

2) Thread one small threaded pipe[K] into end of each small

loop[J].

3) Pass xture wire through rst loop. Thread rst loop onto end

of each last stem.

4) On one side of xture, pass xture wire through second loop

and through hole in canopy[F]. Pass threaded pipe at end of

second loop through hole in canopy.

5) Pass xture wire through lockwasher[P]. Thread lockwasher

onto end of threaded pipe protruding from inside canopy.

6) Pass xture wire through hexnut[Q]. Thread hexnut onto end

of threaded pipe.

7) On other side of xture, pass xture wire through second

loop and through hole in canopy. Pass threaded pipe at end of

second loop through hole in canopy.

8) Pass xture wire through lockwasher. Thread lockwasher onto

end of threaded pipe protruding from inside canopy.

9) Pass xture wire through hexnut. Thread hexnut onto end of

threaded pipe.

10) Aach locking link[I] to small loop at end of each stem and to

each loop on canopy.

11) Follow steps 7 - 14 from Rigid Stem Mount Instrucons.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Fixture Diagram

Parts List

Cauons

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main

fusebox before starng and during the installaon.

WARNING:

This xture is intended for installaon in accordance

with the Naonal Electrical Code (NEC) and all local code

specicaons. If you are not familiar with code requirements,

installaon by a cered electrician is recommended.

Installaon Instrucons – Rigid Stem Mount

[A] Stems

[B] Small

Threaded

Tubes

[C] Outlet Box

[D] Mounting

Plate

[E] Strap

Mounting

Screws

[F] Canopy

[G] Couplings

[H] Fixture Body

[I] Chain Locking

Link

[J] Small Loop

[K] Small

Threaded Pipe

[L] Flat Head

Screws

[M] Glass Spacers

[N] Glass

[O] Decorative

Knobs

[P] Lockwasher

[Q] Hexnut

[R] Wire nuts

AC INPUT

N:WHITE L:BLACK

DC OUTPUT

DC+:RED

DC-:BLUE

AC INPUT

N:WHITE L:BLACK

DC OUTPUT

DC+:RED

DC-:BLUE









WIRING DIAGRAM "A"

INPUT:

120Vac, 50/60HZ

►

This device complies with part 15 of the FCC Rules. Operaon is

subject to the following two condions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including

interference that may cause undesired operaon.

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protecon

against harmful interference in a residenal installaon. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instrucons,

may cause harmful interference to radio communicaons. However,

there is no guarantee that interference will not occur in a parcular

installaon. If this equipment does cause harmful interference to

radio or television recepon, which can be determined by turning

the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

FCC Informaon:

Page is loading ...

IS-44344LED-CB