Asco Series 342 Shut-Off Valve Owner's manual

Asco
Brand
Asco
Model
Series 342 Shut-Off Valve
Type
Owner's manual
Modulair 112 shut-off valve replacement procedure
Page 3
Procédure de remplacement de la vanne de coupure Modulair 112
Page 6
Austausch des Stoppventils Modulair 112
Page 9
Procedura di sostituzione della valvola di chiusura Modulair 112
Page 12
Procedimiento de sustitución de la válvula de corte Modular 112
Page 15
Procedure voor het vervangen van de Modulair 112 afsluitklep
Page 18
GB
FR
DE
IT
ES
NL
(383 46 32)
MS-P710-11
5
4
65
9
8
4
321
10
7
DISASSEMBLY OF MACHINED
BODY VERSION
SHUT-OFF VALVE + SOFT START VALVE
REASSEMBLY OF MOULDED AND MACHINED
BODY VERSIONS
DISASSEMBLY/REASSEMBLY OF MOULDED
BODY VERSION
Modulair 112 shut-off valve replacement procedure
C
D
E
Parts to be replaced:
shut-off valve (4)
and seal (5) supplied with
the valve
+
Parts (1a, 3, 10, 12 and 7)
Replacement kit
code: 343 03 075
- 1 wide ring
- 1 narrow ring (12)
- 2 seals (3 and 10)
- 4 short screws
- 4 long screws (1a)
- 4 nuts (7)
Parts to be replaced:
shut-off valve (4)
and seal (5) supplied with
the valve
+
Parts (1a, 3, 10, 12a and 7)
Replacement kit
code: 343 03 075
- 1 wide ring (12a)
- 1 narrow ring
- 2 seals (3) and (10)
- 4 short screws
- 4 long screws (1a)
- 4 nuts (7)
Part 4 is to be
returned to us
765
10 9
8
4
321a
12
Narrow ring
(4.5 mm)
Machined body
with plain
surface
Moulded body with
plastic cover
8
4
3
765
9
21a
10 12a
Wide ring
(8 mm)
Moulded body with
plastic cover
Moulded body with
plastic cover
Part 4 is to be
returned to us
Modulair 112 shut-off valve replacement procedure
IDENTIFYING YOUR EQUIPMENT
Shut-off valve
machined body version
Shut-off valve
moulded body version
Shut-off valve + soft-start valve
machined body version
Shut-off valve + soft-start valve
moulded body version
For disassembly, see Figure A
For reassembly, see Figure B
For disassambly and
reassembly, see Figure B
For disassembly, see Figure C
For reassembly, see Figure D
For disassambly and
reassembly, see Figure E
4
32
8
5 6
7
1
5 6
8
4
7
321
SHUT-OFF VALVE ONLY
DISASSEMBLY OF MACHINED
BODY VERSION
DISASSEMBLY/REASSEMBLY OF MOULDED
BODY VERSION
Part 4 is to be
returned to us
Moulded body with
plastic cover
Machined body
with plain surface
A B
Part to be replaced:
shut-off valve (4)
+
Parts (1, 3, 5 and 7)
Replacement kit
code: 343 03 075:
- 1 wide ring
- 1 narrow ring
- 2 seals (3 and 5)
- 4 short screws (1)
- 4 long screws
- 4 nuts (7)
7
6
Procédure de remplacement de la vanne de coupure Modulair 112
IDENTIFICATION DE VOTRE MATERIEL
Vanne de coupure
modèle corps usiné
Vanne de coupure
modèle corps moulé
Vanne de coupure + démarreur
modèle corps usiné
Vanne de coupure + démarreur
modèle corps moulé
Démontage voir figure A
Remontage voir figure B
Démontage et remontage
voir figure B
Démontage voir figure C
Remontage voir figure D
Démontage et remontage
voir figure E
4
32
8
5 6
7
1
5 6
8
4
7
321
VANNE DE COUPURE SEULE
DEMONTAGE MODELE CORPS USINE
DEMONTAGE/REMONTAGE MODELE CORPS MOULE
La pièce 4 est
à nous retourner
Corps moulé avec
cache plastique
Corps usiné
avec face lisse
A B
Pièce à changer
vanne de coupure (4)
+
Pièces (1, 3, 5, 7)
Sachet de rechange
code: 343 03 075
- 1 bague large
- 1 bague étroite
- 2 joints (3) et (5)
- 4 vis courtes (1)
- 4 vis longues
- 4 écrous (7)
FR
A
B
SHUT-OFF VALVE + SOFT START VALVE
- Cut off the electrical and pneumatic power supplies, then vent the pneumatic system of the machine.
- Detach the solenoid valve (8) by undoing the two screws.
- Unscrew the silencer or the venting connection.
- Undo the four M5 nuts (7) and the four screws (1a).
- Remove the shut-off valve (4) from the upstream (2) and downstream (6) flanges and from the soft-start valve (9),
and possibly the retaining ring (12) or (12a) for the seal (10).
- Remove and discard all the seals as well as the long screws (1a), the nuts (7) and, possibly, the ring (12) or (12a).
- Clean the seal seatings.
-
Take the seals (3) and (10), the long screws (1a), the nuts (7) and the corresponding ring (12) or (12a) from the replacement kit.
- Lubricate the seals (3, 5 and 10) with Parker-O-Lube.
- Position the new shut-off valve (4) on the soft-start valve (9), positioning the seal (10) and the retaining ring (12 or 12a) for the seal.
- Position the upstream flange (2) (T-groove downwards) with its seal (3) on the shut-off valve (4).
- Positioning the downstream flange (6) (T-groove downwards) with its seal (5) on the shut-off valve (9).
- Insert the four screws (1a) through the components and fit the four M5 nuts (7) (screwing torque 2.5 Nm).
- Reinstall the solenoid pilot valve (8), be sure to orient it correctly (polarised).
- Screw the silencer or the venting connection back on.
- Carry out a functional test (pneumatic and electrical) of the shut-off valve.
DISASSEMBLY AND REASSEMBLY
SHUT-OFF VALVE ONLY
- Cut off the electrical and pneumatic power supplies, then vent the pneumatic system of the machine.
- Detach the solenoid valve (8) by undoing the two screws.
- Unscrew the silencer or the venting connection.
- Undo the four M5 nuts (7) and the four screws (1).
- Remove the shut-off valve (4) the seals (3 and 5) from the upstream (2) and downstream (6) flanges.
- Remove and discard the seals (3 and 5), the short screws (1) and the nuts (7).
- Clean the seal seatings.
- Take the seals (3 and 5), the four shor t screws (1) and the nuts (7) from the replacement kit.
- Lubricate the seals with Parker-O-Lube.
- Position the new shut-off valve (4) with the arrows correctly orientated.
- Position the upstream flange (T-groove downwards) with its seal (3) on the shut-off valve (4).
- Position the downstream flange (6) (T-groove downwards) with its seal (5) on the shut-off valve (4).
- Insert the four screws (1) through the components and fit the four M5 nuts (7) (screwing torque 2.5 Nm).
- Reinstall the solenoid pilot valve (8), be sure to orient it correctly (polarised).
- Screw the silencer or the venting connection back on.
- Carry out a functional test (pneumatic and electrical) of the shut-off valve.
SHUT-OFF VALVE ON FRL LINE OR INSTALLATION WITH ASSEMBLY KIT
- Cut off the electrical and pneumatic power supplies, then vent the pneumatic system of the machine.
- Undo the socket head screws (A) of the upstream and/or downstream connecting pieces (B) to detach the valve from the FRL system,
be sure to retain the O-rings (do not discard) , and proceed with replacement as indicated above.
Modulair 112 shut-off valve replacement procedure
A
B
FOR REPLACEMENT FREE OF CHARGE, THE SHUT-OFF VALVE (4)
MUST BE RETURNED TO US AT THE FOLLOWING ADDRESS:
ASCO JOUCOMATIC SA, After-sales service, 53 rue de Beauce, B.P. 17, 28111 Luce Cedex, France
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Asco Series 342 Shut-Off Valve Owner's manual

Asco
Brand
Asco
Model
Series 342 Shut-Off Valve
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents