Smeg WH1000 Owner's manual

Brand: Smeg

Model: WH1000

Type: Owner's manual

INSTRUCTIONS FOR USE

1. Lid handle

2. Lock (if provided)

3. Seal

4. Defrost water drain plug (if present)

5. Control panel

6. Basket (if present)

7. Condenser (located at the rear)

INSTALLATION

• Please refer to the chapter "BEFORE USING THE

APPLIANCE".

• Unpack the appliance.

• Remove the 4 protection pieces inserted between

lid and appliance.

• Ensure that the defrosting water drainage plug (if

provided) is correctly positioned (4).

• For best operation of the appliance and in order to

avoid damage when the lid is opened, leave a space of

at least 7 cm from the rear wall and 7 cm at the sides.

• Fit the accessories (if provided).

1. Thermostat: it can be used to adjust the internal

temperature of the appliance.

2. Red LED (if provided): Indicates that the appliance

temperature is not sufficiently low.

3. Green LED (if provided): indicates that the appliance is on.

4. Yellow LED (if provided): when on, it indicates that the

fast freeze function has been activated.

5. Fast freeze pushbutton (if provided):

activates/deactivates the fast freeze function.

The exact configuration of the controls may vary

according to the model.

Switching on the appliance

• The appliance is factory set for optimum operation at a

temperature of -18°C.

• Plug in the appliance.

• The green LED lights up (if provided).

• Also the red LED (if provided) will switch on because the

temperature inside the appliance is not yet sufficiently low

for food storage. The red LED will normally switch off

within the first six hours after the appliance is switched on.

• After connecting the appliance to the mains supply and when

the optimal temperature has been reached (this phase takes

about 1 hour during which the lid will not open), ensure that

the fast freeze button is not pressed (the yellow LED, if

provided, is off).

• Place food inside the product only when the red LED (if

provided) has switched off.

• Thanks to the efficient lid seal, the appliance lid will not re-

open easily immediately after closing. Wait a few minutes

before re-opening the lid of the appliance.

Temperature Adjustment

Use the thermostat to select the ideal storage temperature. To

adjust the internal temperature, proceed as follows:

• Turn the thermostat knob to 1 for a storage temperature

that is less cold.

• Turn the thermostat knob to 6 / for a colder storage

temperature.

• For partial loads, or when the load indicator is below the "e"

symbol inside the appliance (if present), it is advisable to

move the thermostat to the lower position (on "e", if present

on the thermostat scale).

Climatic Class Amb. T. (°C) Amb. T. (°F)

SN From 10 to 32 From 50 to 90

N From 16 to 32 From 61 to 90

ST From 16 to 38 From 61 to 100

T From 16 to 43 From 61 to 110

CO Small

INSTRUCTIONS FOR USE

BEFORE USING THE APPLIANCE

Your new appliance is designed exclusively for domestic use

and for storing frozen food, freezing fresh food and making

ice cubes.

Regulations require that the appliance is earthed.

The manufacturer declines all liability for injury to

persons or animals and for damage to property

resulting from failure to observe the above

procedures and reminders.

1. After unpacking, make sure that the appliance is

undamaged and that the lid closes perfectly tight. Any

damage must be reported to your dealer within 24

hours after delivery of the appliance.

2. Wait at least two hours before switching the appliance

on in order to ensure the refrigerant circuit is fully

efficient.

3. Installation of the appliance and electrical connections

must be carried out by a qualified electrician, in

accordance with the manufacturer's instructions and

local safety regulations.

4. Clean the inside of the appliance before using it.

• Before connecting the appliance to the mains supply,

ensure that the voltage corresponds to that given on the

rating plate located on the rear of the appliance.

• Electrical connections must be made in accordance

with local regulations.

FREEZING FOOD

Preparation of fresh food for freezing

• Before freezing, wrap and seal fresh food in: aluminium

foil, cling film, air and water-tight plastic bags,

polyethylene containers with lids, provided they are

suitable for freezing foods.

• Food must be fresh, mature and of prime quality in order

to obtain high quality frozen food.

• Fresh vegetables and fruit should preferably be frozen as

soon as they are picked to maintain the full original

nutritional value, consistency, colour and flavour.

• Always leave hot food to cool before placing in the

appliance.

Freezing fresh food

• Place foods to be frozen in direct contact with the walls

of appliance:

A) - foods to be frozen,

B) - foods already frozen.

• Avoid placing foods to be

frozen in direct contact with

food already frozen.

• For best and fastest freezing,

foods should be split into small

portions; this will also be useful

when the frozen items are to

be used.

1. At least 24 hours before

storing fresh food in the

appliance, press the fast freeze

button. For appliances without

this button, turn the

thermostat to .

2. Place the food to be frozen and keep the lid of the

appliance closed for 24 hours. At the end of this period,

switch off the fast freeze button (if provided).

FOOD STORAGE

Refer to the table on the appliance (if provided).

Classification of frozen

foods

Put the frozen products

into the appliance and

classify them; The storage

date should be indicated on

the packs, to allow use

within expiry dates.

Advice for storing frozen

food

When purchasing frozen food products:

• Ensure that the packaging is not damaged (frozen food in

damaged packaging may have deteriorated). If the

package is swollen or has damp patches, it may not have

been stored under optimal conditions and defrosting may

have already begun.

• When shopping, leave frozen food purchases until last

and transport the products in a thermally insulated cool

bag.

• Once at home, place the frozen foods immediately in the

appliance.

• Avoid, or reduce temperature variations to the

minimum. Respect the best-before date on the package.

• Always observe the storage information on the package.

Note:

Eat fully or partially defrosted foods immediately.

Do not refreeze unless the food is cooked after it has

thawed. Once cooked, the thawed food can be refrozen.

If there is a long power failure:

• Do not open the appliance lid except to place ice packs

(if provided) over the frozen foods on the right and left

of the appliance. This will slow down the rise in

temperature.

MONTHS

FOOD

INSTRUCTIONS FOR USE

PRECAUTIONS AND ADVICE

• After installation, make sure the appliance is not

resting on the power cable.

• Do not store glass containers with liquids in the appliance,

as they could burst.

• Do not eat ice cubes or ice lollies immediately after taking

them out of the appliance, since they could cause cold

burns.

• Before carrying out any maintenance or cleaning operation,

unplug the appliance or disconnect the electrical power

supply.

• Do not install the appliance in places exposed to direct

sunlight or near heat sources, as this will result in higher

energy consumption.

• Do not store or use petrol or other flammable liquids and

gases in the vicinity of this or other electrical appliances.

The fumes can create a fire hazard or explosion.

• Install and level the appliance on a floor able to take its

weight and in a place suitable for its size and use.

• Install the appliance in a dry and well-ventilated place. The

appliance is arranged for use in places with temperatures

inside the following ranges defined according to the

climatic class given on the dataplate located on the back.

The appliance may not work properly if left for a long time

at temperatures outside the range provided for.

• It is advisable to leave the appliance connected, even if

empty even for short periods.

• Be careful not to damage the floors (e.g. parquet) when

moving the appliance. To facilitate moving, it is advisable to

empty the appliance beforehand, if possible.

• Do not use mechanical devices or any means other than

those recommended by the manufacturer to speed up the

defrosting process.

• Do not use electrical appliances inside it, unless they are of

the type recommended by the manufacturer.

• This appliance is not intended for use by people

(including children) with limited physical, sensory or

mental abilities or without experience and

knowledge of it, unless they are supervised or

instructed in its use by a person responsible for their

safety.

• To prevent the risk of children becoming trapped

and suffocating, do not let them play or hide inside

the appliance.

• The power cable must only be replaced by an

authorised person.

• Do not use extension leads or multi-adapters.

• It must be possible to disconnect the power supply

by unplugging or by means of a double-pole mains

switch installed ahead of the socket.

• Make sure the voltage specified on dataplate

matches the voltage in your home.

• Do not swallow the liquid (non-toxic) contained in

the ice packs (if provided).

• Limit the number of times the appliance door is

opened.

DEFROSTING THE

APPLIANCE

The appliance should be defrosted

when the thickness of ice on the

walls reaches 5-6 mm.

• Disconnect the appliance from

the mains power supply.

• Remove the packs of food from

the appliance and wrap them

close together in newspaper and

store in a very cool place or

thermally insulated bag.

• Leave the appliance lid open.

• Remove the internal defrost water drain plug (depending

on model).

• Remove the external defrost water drain plug (depending

on model) and reposition it as shown in the figure.

• Place a bowl beneath the drainage channel to collect the

residual water. If available, use the divider.

• Speed up defrosting by using a spatula to detach the ice

from the appliance walls.

• Remove the ice from the bottom of the appliance.

• In order to avoid permanent damage to the

appliance interior, do not use pointed or sharp metal

instruments for removing the ice.

• Do not use abrasive products or heat up the interior

artificially.

• Dry the interior of the appliance thoroughly.

• On completion of the defrosting, refit the plug.

CARE AND MAINTENANCE

• Remove the ice from the upper edge (see the

Troubleshooting Guide).

• Clean the inside after defrosting, using a sponge dampened

with warm water and/or mild detergent.

• Clean the side motor cooling grille (depending on model).

• Remove dust from the condenser on the rear of the

appliance.

Before carrying out maintenance, unplug the appliance.

Do not use abrasive products, scourers or stain-

removers (e.g. acetone, trichloroethylene) to clean the

appliance.

To obtain the best results from your appliance, carry

out cleaning and maintenance at least once a year.

CHANGING THE LID LIGHT BULB (if provided)

• Disconnect the appliance from the

mains power supply.

• Remove the diffuser by following

the sequence of steps shown in the

figure.

• Unscrew the light bulb and replace

it with an identical bulb of the same

wattage and voltage.

• Refit the diffuser and plug in the appliance.

TROUBLESHOOTING GUIDE

1. The red LED (if provided) remains alight.

• Is there a power failure?

• Is defrosting in progress?

• Is the appliance lid properly closed?

• Is the appliance positioned near a heat source?

• Is the thermostat setting correct?

• Are the ventilation grille and condenser clean?

2. The appliance is too noisy.

• Is the appliance perfectly horizontal?

• Is the appliance in contact with other furniture or objects that

may cause vibrations?

• Has the packaging been removed from under the appliance?

INSTRUCTIONS FOR USE

Note: gurgling noises from the refrigerating circuit after the

compressor cuts out are perfectly normal.

3. The green LED (if provided) is off and the appliance is

not working.

• Is there a power failure?

• Is the plug properly inserted in the socket?

• Is the electric cable intact?

4. The green LED (if provided) is off and the appliance is

working.

• The green LED is not working. Contact the After Sales

Service for a replacement.

5. The compressor runs continuously.

• Have hot foods been put in the appliance?

• Has the appliance lid been left open for a long time?

• Is the appliance positioned in a very warm room or near heat

sources?

• Is the thermostat setting correct?

• Has the fast freeze function (depending on model) been

pressed by mistake?

6. Too much ice on the upper edge.

• Are the defrost water drainage plugs correctly positioned?

• Is the appliance lid properly closed?

• Is the appliance lid seal damaged or deformed? (See chapter

"Installation")

• Have the 4 protection pieces been removed? (See chapter

"Installation")

7. Condensation forms on the external walls of the

appliance

• It is normal for condensation to form under certain

atmospheric conditions (humidity above 85%) or if the

appliance is located in a damp or poorly ventilated room. The

performance of the appliance is in no way affected.

8. The layer of ice on the internal walls of the appliance is

not uniform.

• This phenomenon is quite normal.

SAFEGUARDING THE ENVIRONMENT

1. Packing

The packaging material is entirely recyclable, and marked with

the recycling symbol. Follow local regulations for scrapping.

Keep the packaging materials (plastic bags, polystyrene parts,

etc.) out of reach of children, as they are potentially dangerous.

2. Scrapping

The appliance is manufactured using recyclable material .

This appliance is marked according to the European directive

2002/96/EC on Waste Electrical and Electronic Equipment

(WEEE).

By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment

and human health, which could otherwise be caused by

inappropriate waste handling of this product.

The symbol on the product, or on the documents

accompanying the product, indicates that this appliance may not

be treated as household waste. Instead it shall be handed over to

the applicable collection point for the recycling of electrical and

electronic equipment.

Before scrapping, make the appliance unusable by cutting off the

power cable and removing the doors and shelves so that

children cannot easily climb inside the appliance.

Disposal must be carried out in accordance with local

environmental regulations for waste disposal. Deliver the

appliance immediately to an authorized dump; do not leave it

unattended even for a few days, since it is potentially dangerous

for children. For more detailed information about treatment,

recovery and recycling of this product, please contact your local

city office, your household waste disposal service or the shop

where you purchased the product.

Information:

This appliance does not use CFC. The refrigerant system

contains either R134a (HFC) or R600 (HC). Refer to the rating

plate inside the appliance.

Appliances with Isobutane (R600a): isobutane is a natural gas

without environmental impact, but is flammable. Therefore,

make sure the refrigerant circuit pipes are not damaged.

This product may contain Fluorinated Greenhouse Gases

covered by the Kyoto Protocol; the refrigerant gas is inside a

hermetically sealed system.

Refrigerant gas: R134a has a Global Warming Potential of (GWP)

1300.

Declaration of conformity

• This appliance is intended for storing food and is

manufactured in conformity with European regulation (EC)

No. 1935/2004.

• This product has been designed, manufactured and marketed

in compliance with:

- the safety objectives of Low Voltage Directive 2006/95/EC

(replacing 73/23/EEC and subsequent amendments);

- the protection requirements of Directive "EMC"

2004/108/CE.

• The electrical safety of the appliance can only be guaranteed if

the product is connected to an approved earth connection.

AFTER-SALES SERVICE

Before contacting After-Sales Service:

1. See if you can solve the problem yourself.

2. Switch the appliance on again to see if the problem has

been solved. If it has not, disconnect the appliance from the

power supply and wait for about an hour before switching

on again.

3. If the problem persists after this course of action, contact

After-Sales Service.

Specify:

• the nature of the fault,

• the model,

• the service number (the number after the word SERVICE on

the rating plate on the rear of the appliance)

• your full address,

• your telephone number and area code.

Smeg WH1000 Owner's manual

Smeg WH1000 Owner's manual

Smeg WH1000 Owner's manual

Related papers

Other documents