Cross Technologies 2115-34 Owner's manual

Type
Owner's manual
Instruction Manual Model 2115-34
Block Upconverter
February 2015, Rev D
MODEL 2115
CROSS TECHNOLOGIES INC.
POWER
UPCONVERTER
EXT
10MHZ
ALARM
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment. Printed in USA.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
Instruction Manual
MODEL 2115-34 Block Upconverter
TABLE OF CONTENTS PAGE
Warranty 2
1.0 General 3
1.1 Equipment Description 3
1.2 Technical Characteristics 4
2.0 Installation 5
2.1 Mechanical 5
2.2 Rear Inputs and Outputs 6
2.3 Front Panel Indicators 6
2.4 Operation 7
2.5 Environmental Use Information 8
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and
workmanship for a period of one year after shipment to customer. Cross Technologies,
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s
option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall
not be liable for any special, indirect, or consequential damages. This warranty does not
cover parts or equipment which have been subject to misuse, negligence, or accident by the
customer during use. All shipping costs for warranty repairs will be prepaid by the
customer. There are not other warranties, express or implied, except as stated herein.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
2115-34 Manual, Rev. D Page 2 02/12/15
MODEL 2115-34 Block Upconverter
1.0 General
1.1 Equipment Description
The 2115-34 Block Upconverter converts 0.95 - 1.75 GHz to 3.4 - 4.2 GHz with low phase noise and flat
frequency response. Dual conversion frequency translation is via 11.26 and 8.81 GHz local oscillators. Front
panel LEDs provide indication of DC Power, External 10 MHz, and PLL Alarm. The gain is +20 dB.
Connectors are Type N female for the RF and BNC female for the L-Band and external reference input and
reference output. A three-way switch controls which 10 MHz reference is being used. In the INT position, the
internal reference is used, in the EXT position, the external reference is used, and in the AUTO position, the
internal reference is used unless a 3 dBm ± 3 dB, 10MHz reference signal is connected to the external reference
input. The 2115 is powered by a 100-240 ±10% VAC power supply, and mounted in a 1 3/4” X 19” X 14” rack
mount chassis.
MODEL 2115
CROSS TECHNOLOGIES INC.
POWER
UPCONVERTER
EXT
10MHZ
ALARM
FRONT PANEL
AC
GND
J8
J2
EXT 10MHZ
RF OUTPUT
INPUT
10MHZ REF
OUTPUT
INT EXT
AUTO
S1 J1
L-BAND
INPUT
J101
J11
ALARM
15 234
6789
REAR PANEL
FIGURE 1.1 Front and Rear Panels
2115-34 Block Diagram
3.4
to
4.2
GHz
OUT
0.95
to
1.75
GHz
IN
8.81
GHz
3.4 to 4.2 GHz BP
EXT 10MHZ
10 MHZ
MON
AUTO
INT
10MHZ
12.21 to 13.01 GHz
BP
11.26
GHz
10MHZ
FIGURE 1.2 Model 2115-34 Upconverter Block Diagram
2115-34 Manual, Rev. D Page 3 02/12/15
1.2 Technical Characteristics
TABLE 1.0 2115-34 Upconverter Specifications*
Input Characteristics
Impedance/Return Loss 50 Ω /14 dB (see TABLE 2.2 for connector options)
Frequency 0.95 to 1.75 GHz
Noise Figure, max. 20 dB, max. gain
Input Level -40 to -20 dBm
Input 1dB Compression -10dBm
Output Characteristics
Impedance/Return Loss 50 Ω/14 dB (see TABLE 2.2 for connector options)
Frequency 3.4 to 4.2 GHz
Output Level Range -20 to 0 dBm
Output 1dB Compression +5 dBm
Channel Characteristics
Gain +20 dB ± 1 dB
Image Rejection > 60 dB
Spurious, Inband Signal Related < -55 dBC, 0 dBm out; Signal Independent, <-60 dBm
Spurious, Out of Band < -50 dBm
Intermodulation < -50 dBC for two carriers each at -10 dBm out
Frequency Response ±1.5 dB, 3.4 to 4.2 GHz; ± 0.5 dB, 40 MHz BW
Frequency Sense Non-Inverting
LO Characteristics
LO Frequency 11.26 and 8.81 GHz
Frequency Accuracy ± 0.01 ppm max. over temp internal reference
10 MHz Level 3 dBm, ±3 dB, External In or 10MHz Out
-110-100-85-80-70
1MHz100kHz10kHz1kHz100 Hz
dBC/Hz
Phase Noise
@
Fre
q
Controls, Indicators
Power Green LED
PLL Alarm Red LED, External contact closure
Ext 10 MHz Yellow LED, Indicates Ext 10 MHz reference is selected (rear panel sw)
Other
RF Connector Type N, 50Ω, female (see TABLE 2.2 for other options)
L-Band Connector BNC 50Ω, female (see TABLE 2.2 for other options)
10 MHz Connectors BNC (female) 75Ω connector; Works with 50Ω or 75Ω.
Alarm Connector DB9, female - NO or NC contact closure on Alarm
Size 19 inch, 1RU standard chassis 1.75” high X 14.0” deep
Power 100-240 ±10% VAC, 47-63 Hz, 25 watts max.
Available Connector Options
N - 50Ω N-type (RF), 75Ω BNC (L-BAND)
NF - 50Ω N-type (RF), 75Ω F-type (L-BAND)
NN - 50Ω N-type (RF), 50Ω N-type (L-BAND)
S7 - 50Ω SMA (RF), 75Ω BNC (L-BAND)
SF- 50Ω SMA (RF), 75Ω F-type (L-BAND)
SN - 50Ω SMA (RF), 50Ω N-type (L-BAND)
SS - 50Ω SMA (RF), 50Ω SMA (L-BAND)
*+10˚C to +40˚C; Specifications subject to change without notice.
2115-34 Manual, Rev. D Page 4 02/12/15
2.0 Installation
2.1 Mechanical
The 2115-34 consists of one RF PCB housed in a 1 RU (1 3/4 inch high) by 12 inch deep chassis. A switching,
± 12, +24, +5 VDC power supply provides power for the assemblies. The 2115-34 can be secured to a rack
using the 4 holes on the front panel. Figure 2.0 shows how the 2115-34 is assembled.
1
PS IN
PIN 1, +12 VDC
PIN 2, +5 VDC
PIN 3, +5 VDC
PIN 4, GROUND
PIN 5, GROUND
PIN 6, -12 VDC
PIN 7, +24 VDC
PIN 8, +24 VDC
POWER
SUPPLY
J10
J101 - Panel Mount
Type N Connector
BP FILTER/
ISOLATOR
A4
J7
FIGURE 2.0 2115-34 Mechanical Assembly
2115-34 Manual, Rev. D Page 5 02/12/15
2.2 Rear Panel Input/Output Signals - Figure 2.1 shows the input and output connectors on the rear panel.
AC
GND
J8
J2
EXT 10MHZ
RF OUTPUT
INPUT
10MHZ REF
OUTPUT
INT EXT
AUTO
S1 J1
L-BAND
INPUT
J101
5 4 3 2
1
9 8 7 6
J11
ALARM
J1 - L-BAND INPUT
BNC (female) 50 Ω. 0.95 to 1.525 GHz,
-20 dBm max input signal. See Table
2.2 for other connector o
p
tions.
AC INPUT
100-240 ±10% VAC, 47-60 HZ
Uses 2 amp Slow Blo,
5mm fuse
S1 - 10MHZ SWITCH
3-position switch. INT selects internal 10MHz ref.
AUTO selects internal 10MHz ref, unless a 0dBm
±3 dB 10MHz signal is inserted on
J2. EXT selects external 10MHz ref from J2.
J1 - EXT 10MHZ INPUT
BNC (female) 75 Ω. Insert external
10MHz reference here (0 dBm ± 3
J101 - RF OUTPUT
Type N (female) 50 Ω. 5.85 to
6.425 GHz, 0 dBm max output
signal. See Table 2.2 for other
connector o
p
tions.
J11 - ALARM
DB9 (female) connector.
See Table 2.1.
J8 - 10MHZ REF OUTPUT
BNC (female) 75 Ω. Outputs currently
selected 10MHz ref si
g
nal
(
0 dBm ±3 dB
)
.
FIGURE 2.1 2115-34 Rear Panel I/Oʼs
TABLE 2.1 JJ11
TABLE 2.1 J11 Pinouts (DB9)
Pin Function
1 Not Used
2 Not Used
3 Not Used
4 Not Used
5GND
6 Alarm Relay: Common
7 Alarm Relay: Normally Open
8 Not Used
9 Alarm Relay: Normally Closed
TABLE 2.2 Connector
n
Options
Option RF L-Band
STD Type N, 50Ω BNC, 50Ω
N Type N, 50Ω BNC, 75Ω
NF Type N, 50Ω Type F, 75Ω
NN Type N, 50Ω Type N, 50Ω
S SMA, 50Ω BNC, 50Ω
S7 SMA, 50Ω BNC, 75Ω
SF SMA, 50Ω Type F, 75Ω
SN SMA, 50Ω Type N, 50Ω
SS SMA, 50Ω SMA, 50Ω
2.3 Front Panel Indicators -The following are the front panel indicators.
DS2 - ALARM LED
Lights RED when PLL comes
out of lock.
DS1 - POWER LED
Lights GREEN when DC
voltage is present from AC
power supply.
DS3 - EXT 10MHZ LED
Lights YELLOW when external
10MHz reference is active.
MODEL 2115
CROSS TECHNOLOGIES INC.
POWER
UPCONVERTER
EXT
10MHZ
ALARM
FIGURE 2.2 2115-34 Front Panel Controls and Indicators
2115-34 Manual, Rev. D Page 6 02/12/15
2.4 Installation / Operation
2.4.1 Installing and Operating the 2115-34 Upconverter
1. Connect a -40 dBm to -20 dBm signal to L-BAND INPUT, J1 (Figure 2.1).
2. Connect the RF OUTPUT, J101, to the external equipment.
3. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC connector on the back panel.
4. Be sure DS1 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.2).
5. Select either INT (for internal 10MHz ref), AUTO (for internal 10MHz ref UNLESS a external
10MHz, +3 dBm signal is connected to J2), or EXT (for external 10MHz, +3 dBm ref that is inserted at
J2) on rear panel switch S1 (Figure 2.1).
6. If EXT is selected or AUTO is selected and there is a 10MHz, +3 dBm signal at J2, check that DS3
(yellow, Ext 10MHZ) is on (Figure 2.2).
7. Check that a 10MHz, +3 dBm ±3 dB signal is present at the 10MHZ REF OUTPUT (J8) (Figure 2.1).
8. AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot in the
drawer below the AC input as shown in Figure 2.3. There is a spare fuse in the near slot. If a fuse
continues to open, the power supply is most likely defective.
AC Fuse - 2 amp slow blow (Type T),
5 mm X 20 mm
FUSE DRAWER
SPARE FUSE
~
INPUT
100-240± 10%VA
C
47-63 Hz
2A MA
X
FUSE
TYPE T 2A GDC
250 VOLT
FOR 100 - 240 V~
~
FIGURE 2.3 Fuse Location and Spare Fuse
2115-34 Manual, Rev. D Page 7 02/12/15
2.5 Environmental Use Information
A. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions
located in the user manual furnished by the manufacturer of your equipment rack.
B. Mechanical Loading - Mounting of equipment in a rack should be such that a hazardous condition
does not exist due to uneven weight distribution.
C. Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack may be greater than room ambient temperature.
Therefore, consideration should be given to Tmra (Maximum Recommended Ambient Temperature).
D. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. Additional space between unit
may be required.
E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of circuits could have on over current protection and supply wiring.
Appropriate consideration of equipment name plate rating should be used when addressing this concern.
F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct connection to the
Branch (use of power strips).
G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.
If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED
prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS
emission problems.
2115-34 Manual, Rev. D Page 8 02/12/15
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
Printed in USA
2115-34 Manual, Rev. D Page 9 02/12/15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Cross Technologies 2115-34 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI