Beam TR400 Quick start guide

Brand: Beam

Model: TR400

Type: Quick start guide

Terra 400 & Oceana 400

Quick Start Guide

www.beamcommunications.com

PART #: USRQSG005803

BEAM Communications Pty Ltd

5/8 Anzed Court, Mulgrave

Victoria, 3170, AUSTRALIA

Web: www.beamcommunications.com

Information: info@beamcommunications.com

Support: suppor[email protected]

Tel: +61 3 8588 4500

Fax: +61 3 9560 9055

2. SIM Instrallation

If your Service Provider has not installed

the SIM card for you, follow these steps

to install.

1. Turn power OFF to the Terminal.

Failure to turn OFF can result

in corruption of your SIM card

memory.

2. Release the SIM cover by

unclipping the latch with your

nger or thumb. The SIM Cover is

shown highlighted below.

3. Slide the tray guide of the SIM

connector into the Open position.

4. Raise the SIM tray as shown below.

5. Gently insert the SIM card into

the tray slots making sure that

the golden connectors are facing

downwards.

6. Lower the tray and slide the tray

guide into the lock position.

7. Replace the SIM cover.

1. Terra 400 & Oceana 400 Equipment

Overview

1. Signal LED

2. Call LED

3. Message LED

4. Antenna TNC Connector

5. GPS SMA Connector

6. Wall Moutning Hooks

7. SIM Card Slot and Cover

8. USB Port

9. POTS/RJ11 Port

10. Power Port

Terra 400

4. Connecting Power to the Terminal

The TR400/OC400 terminal can be

powered from the supplied AC Plug pack,

or connected to an external 10-32V DC

power source.

ISD950 AC Plug Pack Installation

For installation using the ISD950 110-

240 AC plug pack, connect the 4-way

Microt connector from the plug pack

to the 4-way power connector on the

rear of the TR400/OC400 terminal. In this

conguration the status is always ON.

DC Power Source Installation

The DC power cable has three wires, RED,

BLACK and YELLOW. The RED and BLACK

wires are used for the power connection,

The YELLOW wire can be connected to a

circuit to sync the ON/OFF status of the

TR400/OC400 terminal with a vessels/in-

building operation.

By default, the TR400/OC400 terminal will stay

on for 20 minutes after this input (YELLOW wire)

is switched OFF. If a call is in progress while this

occurs, the TR400/OC400 terminal will stay on

for 20 minutes after the call is terminated. Please

follow the steps below to connect the DC power

cable to the battery power and the TR400/OC400

terminal.

Route the wire end of the DC power cable to

the connection point.

1. Connect the BLACK wire to the

negative terminal of the battery.

2. Connect the RED wire to the

positive terminal of the battery. It is

recommended to add the 5A fuse

(supplied) between them.

3. Connect the YELLOW wire to accessory

power or ON/OFF switch wire. It is

recommended to add a 1A fuse between

them. If the SLEEP function is not required,

the YELLOW wire MUST be connected to

the RED wire.

4. Connect the 4-way Microt connector

on the DC power cable to the 4-way

power connector on the rear of the

TR400/OC400.

5. Connect the 4-way Microt connector

on the DC power cable to the 4-way

power connector on the rear of the

TR400/OC400.

6. Wall Mounting & Locking Bolt

There are two mounting points at the back

of the terminal (as shown, shaded, in the

below image). The distance (from centre to

centre) between the mounting points is 10

cm. To mount the terminal vertically on a

wall, sit the two included screws with 4mm

remaning out of the wall. Adjust this depth

till the terminal hangs securly on the screws.

NOTE

Vertical (wall) mounting orientation is required to

maintain IP53 rain protection.

8. Terra 400 / Oceana 400 Types of Tones

7. Terra 400 / Oceana 400 Status Table

3. Antenna Connection

1. Refer to the antennas installation

guide for antenna mounting and

location requirements.

2. Connect the antenna cable labelled

“GPS” to the SMA antenna connector

labelled “GPS”.

3. Connect the antenna cable labelled

“Inmarsat” to the SMA antenna connector

labelled “ISAT”.

4. Connect the GPS-SMA (F) cable end to

the terminal’s SMA connector

5. Connect the TNC (F) antenna cable

end to the terminal’s satellite

connector.

ISD710 - FOR USE WITH OC400

ISD700 - FOR USE WITH TR400

WARNING

DO NOT pull with force on the cables from the

rear of the OC400/TR400. Please install strain relief

clamping for the antenna cables where required.

Correct installation of the antenna system is a

vital part of theOC400/TR400 system, to ensure

reliable functionality, and drop-free calls.

WARNING

Changes or modications not expressly approved

by Beam Communications could void the

product warranty.

WARNING

To satisfy FCC RF exposure requirements for mobile

transmitting devices, a separation distance of

55cm or more should be maintained between the

antenna of this device and persons during device

operation. To ensure compliance, operations at

closer than this distance is not recommended.

5.Connect POTS/RJ11

Any standard analogue POTS telephone

(POTS = Plain Old Telephone Service)

is supported by the TR400/OC400

Terminal. The Terminal supplies power

to the analogue phone as well as ring,

dial and busy tones.

The analogue phone can be connected

by up to 600m (2000’) of cabling to the

TR400/OC400.

TNC

SMA

Satellite

Antenna

Cable

GPS

Antenna

Cable

THIS SIDE UP

TNC

SMA

Satellite

Antenna

Cable

GPS

Antenna

Cable

ISD710

Maritime Antenna

(Active)

For use with OC400

ISD700

Fixed/Directional

Antenna (Passive)

For use with

TR400

10cm

MOUNTING

SCREWS

~4mm

<60°

TYPE OF TONE SOUND DESCRIPTION

Dial Tone Continuous tone Telephone ready for use

Progress Tone Continuous short beep, with 3

second interval

Number has been dialled but call has yet to connect.

Unavailable Tone Beeping tone (engaged) Phone is not registered, or no signal. Calls cannot be made

SIM PIN Required Alternating low and lower tones (1

sec intervals)

A SIM PIN is required to be entered

SIM PUK Required Alternating low and lower tones (2

sec intervals)

A PUK code is required to be entered

Phone o-hook Fast ascending tone, repeating. Phone has been left ohook for > 15 seconds and is not in a call.

SIGNAL LED

GREEN RED YELLOW

ON Good signal

Registered

No signal

Registered

Poor signal

Registered

FLASHING Good signal

Not registered

No Signal

Not registered

Poor signal

Not registered

ALTERNATING Alternating GREEN, YELLOW, RED.

Error state entered. The Call and Message LED’s indicate the error code.

MESSAGE LED

GREEN RED YELLOW

ON N/A N/A N/A

FLASHING Voice mail has been received SMS is present in the inbox Both a voice mail and inbound

SMS has been received

ALTERNATING N/A N/A N/A

CALL LED

GREEN RED YELLOW

ON POTS o-hook N/A DTR present on data port

FLASHING POTS call in progress N/A Data call in progress (DCD

active)

ALTERNATING N/A N/A N/A

Special modes of operation

• Firmware upgrade mode - In rmware upgrade mode all LED’s will turn solid YELLOW. Entering this mode will be accompanied by a

long beep followed by three short beeps.

• Transceiver (USB Bridge) mode - In this mode all LED’s will ash GREEN.

Beam TR400 Quick start guide

Beam TR400 Quick start guide

Beam TR400 Quick start guide

Related papers

Other documents