Danfoss GBC Ball Valve - 45 bar for CO2 Installation guide

Type
Installation guide
DKRCC.PI.FB0.C3.02 © Danfoss A/S (AC-MCI / sw), 2016-05
Shut-o ball valve for R744 (45 bar/650 psi)
Type GBC 6s to GBC 42s
009R9517
009R9517
Installation guide
Temperature range: -40 – 150 °C / -40 – 300 °F
Max. working pressure (PS/MWP):
45 bar/650 psi
Remove access cap (if present)
OPEN position
CLOSED position
Refrigerant: R744 (CO
2
)
Opening valve
Single-ow
1
2
Valve size
Max. Torque
Nm ft-lbs
6s - 22s 7 5.2
28s 17 12.6
35s 20 14.8
42s 34 25.2
Warning: Only authorized persons are allowed to operate this valve, as closing can cause
build-up of excessive pressure in the system.
Applicable to all common non-ammable refrigerants, excluding R717 andto noncorrosive
gases/liquids dependent on sealing material compatibility.
The design pressure shall not be less than the value outlined in Section 9.2 of ANSI/
ASHRAE 15 for the refrigerant used in the system.
Danfoss
9G219.10
Component
to be insulated
Danfoss
9G227.10
A
t
t
e
n
t
i
o
n
!
D
o
n
u
t
r
e
m
o
v
e
t
h
i
s
n
u
t
A
t
t
e
n
t
i
o
n
!
D
o
n
u
t
r
e
m
o
v
e
t
h
i
s
n
u
t
Danfoss
9G228.10
A
t
t
e
n
t
i
o
n
!
D
o
n
u
t
r
e
m
o
v
e
t
h
i
s
n
u
t
A
t
t
e
n
t
i
o
n
!
D
o
n
u
t
r
e
m
o
v
e
t
h
i
s
n
u
t
A
t
t
e
n
t
i
o
n
!
D
o
n
u
t
r
e
m
o
v
e
t
h
i
s
n
u
t
Danfoss
9G229.10
Danfoss
9G230.10
2 DKRCC.PI.FB0.C3.02 © Danfoss A/S (AC-MCI / sw), 2016-05
Danfoss
9G226.10
Install Schrader valve
and cap (if present)
4
Brazing
Min. 5% Ag
3
Max. 150°C
(300°F)
Fully open
Fully closed
Install Schrader valve
with approx. torque
0.3 Nm / 0.2 ft-lbs
A
t
t
e
n
t
i
o
n
!
D
o
n
u
t
r
e
m
o
v
e
t
h
i
s
n
u
t
Danfoss
9G209.10
A
t
t
e
n
t
i
o
n
!
D
o
n
u
t
r
e
m
o
v
e
t
h
i
s
n
u
t
A
t
t
e
n
t
i
o
n
!
D
o
n
u
t
r
e
m
o
v
e
t
h
i
s
n
u
t
A
t
t
e
n
t
i
o
n
!
D
o
n
u
t
r
e
m
o
v
e
t
h
i
s
n
u
t
Danfoss
9G224.10
  • Page 1 1
  • Page 2 2

Danfoss GBC Ball Valve - 45 bar for CO2 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI