Voyager JWM12A Owner's manual

Voyager
Brand
Voyager
Model
JWM12A
Category
Car media receivers
Type
Owner's manual
Owner's Manual
MOBILE AUDIO SYSTEM
JWM12A
H M
JWM12A
Introduction.........................................................
Installation..........................................................
Wiring..............................................................
Basic Operation.....................................................
Tuner Operation.....................................................
Bluetooth Operation..................................................
APP Operation......................................................
Specifications.......................................................
3
4
5
6
7
8
9
9
CONTENTS
JWM12A
INTRODUCTION
Thank You!
Features
Precautions
Thank you for choosing a Jensen product. We hope you will find the instructions
in this owner ’s manual clear and easy to follow. If you take a few minutes to look
through it, you’ll learn how to use all the features of your new Jensen receiver for
maximum enjoyment.
Features of Jensen JWM12A mobile audio system include:
Ÿ Backlit Controls and Display
Ÿ AM/FM Tuner/30 Preset station (12 AM/18 FM)
Ÿ Bluetooth Ready with A2DP/AVRCP streaming Audio
Ÿ APP Ready
Ÿ Electronic Bass, Treble, Balance and Fader Controls
Ÿ Time/Alarm Clock
Ÿ 1/8" Front Aux Audio Input
Ÿ Rear Audio RCA Input
Ÿ 4 Speaker Outputs (2 zones)
Ÿ Use the Proper Power Supply
This product is designed to operate with a 12 volt DC, negative ground
battery system (the standard system in a North Ame rican vehicle).
Ÿ Use Auth oriz ed Ser vice Centers.
Do not attempt to disassemble or ad just this precisi on product; contact a
professional for assistance.
Ÿ Avoid Moisture
To reduce the risk of fire or electric shock, do not expose this equipment to
rain or moisture.
Ÿ Avoid Cleaning Products.
The front of this unit should only be cleaned wi th a slightly damp cloth. Do
not use cleansers.
Ÿ Use Recommended Accessories.
TO REDUCE THE RISK OF FIRE OR ELECT RIC SHOCK A ND ANNOYING
INTERF ERENCE, USE ONLY THE RECOMMENDE D ACC ESS ORIE S.
Packing List
3
.
JWM12A
INSTALLATIONINSTALLATION
It’s a good idea to read all of the instructions before beginning the installation.
We recommend having your Jensen JWM12A installed by a reputable RV
dealership.
You will need these tools and supplies to install your JWM12A:
Select a mounting location, taking care to avoid the following:
Ÿ Phillips screwdriver
Ÿ Wire cutters and strippers
Ÿ Tools to remove existing radio (screwdriver, socket wrench set or other tools)
Ÿ Electrical tape
Ÿ Crimping tool
Ÿ Volt meter/test light
Ÿ Crimp connections
Ÿ 16 gauge wire for power connections
Ÿ 16 –18 gauge speaker wire
Tools and Supplies
Disconnecting the Battery
Selecting the Mounting Location
Mounting the Radio
To prevent a short circuit, be sure to turn off the ignition and remove the negative
(-) battery cable prior to installation.
NOTE: If the JWM12A is to be installed in a vehicle equipped with an on-
board drive or navigation computer, do not disconnect the battery cable. If
the cable is disconnected, the computer memory may be lost. Under these
conditions, use extra caution during installation to avoid causing a short
circuit.
Ÿ Places exposed to heat-radiating appliances such as electric heaters
Ÿ Adjacent to other equipment that radiates heat
Ÿ Poorly-ventilated or dusty places
Ÿ Moist or humid locations
Ÿ Use the mounting hole diagram to measure and cut a mounting hole
Ÿ Route power, speakers, AV, and antenna cables through the hole and connect
Ÿ Check and ensure correct operation
Ÿ Mount the unit using two M3x20mm (3/32 x 0.75") screws
Ÿ Attach Trim ring
NOTE: Before cutting the mounting hole, make sure the area behind the
mounting location is clear of wires, fuel and vacuum or brake lines.
4
JWM12A
DETAIL A
SHOWN FROM PIN VIEW
PIN NO. WIRE COLOR FUNCTION (Label Contents)
LIGHT GREEN/BLACK
LIGHT GREEN
WIRING
AMP REMOTE(+12VDC 100MA)
1
9
5
13
17
2
10
6
14
18
3
11
7
15
19
4
12
8
16
20
BLACK A-GND
N/A N/A
N/A N/A
N/A N/A
N/A
N/A N/A
RED REAR AUX IN_R
REAR AUX IN_L
A-GND
WHITE
BLACK
BLUE
RED
BLACK
VIOLET
VIOLET/BLACK
GRAY
GRAY/BLACK
WHITE/BLACK
WHITE
N/A
The wiring diagram depicts all the wiring connections required for proper operation of the unit.
LEFT(B) SPEAKER(+)
LEFT(A) SPEAKER(+)
LEFT(B) SPEAKER(-)
LEFT(A) SPEAKER(-)
RIGHT(B) SPEAKER(-)
RIGHT(A) SPEAKER(-)
RIGHT(B) SPEAKER(+)
RIGHT(A) SPEAKER(+)
GROUND
+12VDC SWITCHED
ANT SOCKET
20PIN CONNECTOR
5
10 AMP FUSE
10 AMP F USE
.
JWM12A
BASIC OPERATION
Power
Mode
Audio menu setting
System menu setting
Press the POWER/MODE button (3) to turn the unit on.
Press and hold the POWER/MODE button (3) to enter standby mode from unit on.
After unit turn on, press the POWER/MODE button (3) to cycle through available
modes and choose the desired mode.
Press the AUDIO/SETTING button (4) to choose the following audio menu list:
Sleep Mode
Liquid Crystal Display(LCD)Back Light
Ÿ Sleep: The Sleep Timer will automatically turn off the JWM12A in the
designated number of minutes. To set the Sleep Time, press To set the
Sleep Time, press VOLUME / repeatedly to change the sleep time from
0(off),15,30.45 or 60 minutes.
Ÿ Dimmer: Adjust the brightness of the LCD from "BRI 9" (brightest) to "BRI 0" (off).
NOTE: When subjected to cold temperatures for an extended period of time,
LCD panels will take longer to illuminate and the display visibility may slightly
decrease. Optimal LCD operation will return to normal when the temperature
increases to a normal range.
Setting the alarm
Setting the Bluetooth
Reset
Ÿ Alarm ON/OFF: Press VOLUME / to turn on and off the alarm. The "ALARM"
icon will show on the display.
Ÿ Press the VOLUME button (2) to adjust the hour or press the VOLUME
button (1) to adjust the minute.
Ÿ BT ON/OFF: Press the VOLUME / button to turn on and off the Bluetooth
function
Ÿ BT DEV (Locked/Unlocked, Disconnect/Connect, Delete) :View, lock and delete
from a list of previously paired mobile device models.
Ÿ BT PAIR: Press BAND/ENTER (7) to start pairing with a Bluetooth enabled
device.
Ÿ Preset Volume (PVOL): Select an automatic turn on volume.
RESET: Press BAND/ENTER button (7) reset the to factory default settings. This
function will time out after 5 seconds of inactivity and the unit will resume normal
operation.
Ÿ BAS: Adjust the Bass level from "-7" to "+7".
Ÿ TRE: Adjust the treble from "-7" to "+7".
Ÿ BAL: Adjust the speaker output balance between "L7" (left) and "R7" (right).
"BAL 0" indicates an equal balance between the left and right speakers.
Ÿ LOUD: Toggle the loudness on/off. When listening to music at low volumes,
this feature will boost the bass/treble ranges to compensate for the
characteristics of human hearing.
Ÿ Use the VOLUME / to make adjustments in each menu item.
Press and hold the AUDIO/SETTING button to enter system menu list and press
AUDIO/SETTING once again to choose the following system menu list:
Volume control
Press the VOLUME to increase the volume output. Press and hold the
VOLUME to increase the volume output continuously.
Press the VOLUME to decrease the volume output. Press and hold the
VOLUME to decrease the volume output continuously.
Audio Adjustment
6
1
2
3
4
5
6
7
8 9
10
11
12
13 14 15
H M
Auxiliary Input Function
When a portable audio device is connected to the unit, press the
POWER/MODE button(3) repeatedly until AUX 1/ AUX 2 mode is
selectable. To connect a portable audio device, insert a standard 3.5mm(audio line
output or headphone output from your portable CD/MP3 iPod or other media) into the
AUX IN connector(6) on the front of the unit or the AUX-IN RCA jack(AUX AUDIO
INPUT) on the rear of the unit.
M
M
H
H
H
M
JWM12A
Auxiliary Input Connector
Clock Display
Clock Setup
Zone Output
Press the VIEW/SET button (8) to alternate the display between Playback mode
and clock time while in Tuner, Bluetooth or auxiliary input mode.
Press and hold the VIEW/SET button (8) to access Clock Setup mode. The
number representing the hours and minutes will flash. Press VOLUME
buttons to adjust the hour. Press the VOLUME buttons to adjust the minutes.
The new time will be saved 5 seconds after the last adjustment is made.
The two zone output buttons (11)/(12) (ZONE A and ZONE B) control zone output
from the radio. Press any of the two buttons to turn the corresponding speaker
sets on or off.
For front panel audio input, an external audio source can be connected with a
3.5mm audio cable adapter. Connect the device to the AUX IN connector(6) on
the front panel. In addition to front panel auxiliary input source, the external audio
source can also be connected to the RCA audio input
through the AUX AUDIO INPUT jack
on the rear of the unit.
Select a Band
Manual Tuning
Preset Stations
Press BAND/ ENTER(7) to change between three FM bands (FM1, FM2 and FM3)
and two AM bands (AM1 and AM2).
Press the tune up(15) or tune down(13) buttons to tune the frequency one step
higher or lower. Press and hold to seek tune to next strong station.
Six numbered preset buttons store and recall stations for each AM and FM band.
Select a band (if needed), then select a station. Hold a preset button for one second.
The current station will be stored, and the corresponding preset number will appear
in the display.
Select a band (if needed). Press a preset button momentarily, and the unit will tune to
the corresponding stored station.
Store Preset Stations
Recall Preset Stations
1
2
3
4
5
6
7
8 9
10
11
12
13 14 15
H M
TUNER OPERATION
Automatically Store / Preset Scan (AS/PS)Automatically Store
Press and hold the AS/PS button (5) for more than one second, and the unit will
automatically scan for and store six strong stations for all bands. To stop this function
before the automatic storing is complete, press AS/PS again.
Press AS/PS to scan all preset stations in the current band. The unit will play each
station for five seconds before moving on to the next station. To stop this function and
play the current station, press the AS/PS button again.
Automatically Store
Preset Scan
7
H
M
JWM12A
BLUETOOTH OPERATION
The JWM12A includes built-in Bluetooth technology that allows you to connect
this head unit to Bluetooth-enabled devices for streaming audio playback.
1. Press the button (10) to enter menu adjustment mode.
2. With "Device" displayed, press the buttons to select.
3. Press the buttons to view paired BT devices and press
BAND/ENTER(7)button to select.
4. Once a device is selected, press the buttons to choose one of
the following options: connect/disconnect, locked/unlocked or delete (delete
displays only if the device is not connected).
Ÿ LOCKED/UNLOCKED: The JWM12A can store up to 5 devices for BT
connection. The devices are stored in FIFO (First In First Out) order. To
prevent a device from being bumped from the list when more than 5 devices
are used, you must lock the device. To Lock/Unlock a device, press the
BAND/ENTER button.
Ÿ DISCONNECT: To disconnect a paired device, press the BAND/ENTER
button to temporarily remove the BT link. The link can be re-established
through your phone menu by selecting the JWM12A for connection.
Ÿ DELETE: To delete a device from the list, press the BAND/ENTER button.
Bluetooth wireless technology is a short-range wireless radio protocol.
Operating in the 2.4 GHz range,it transmits audio and data at speeds up to 2.1
Mbit/s over a range of up to 10 meters.
5.Press the BAND/ENTER button to enter.
Before you begin, consult the owner's manual for the Bluetooth device you want
to pair with the JWM12A.
The A2DP music is available for Bluetooth enabled phones when the phone is
connected. To access Bluetooth mode and play songs stored on your phone,
press the button (10). While in BT mode , the "BT AUDIO" is
displayed on the LCD.
During playback, press the tune up >>|(15) or tune down |<<(13) to play the
previous or next track.
During playback, press the button(14) to pause the BT AUDIO player. Press
again to resume playback. If you change to another mode, the mobile phone audio
will pause. Press the button (10) to return to BT mode and resume mobile
phone audio playback.
NOTE: If a Bluetooth device is disconnected due to the power being turned
off or if the device is out of range, the unit will automatically search for the
matching Bluetooth mobile device when the power is restored.
1. Make sure the device you want to pair is on and ready to receive a signal from
the JWM12A. To begin pairing, press and hold the button (10). The unit
will automatically attempt to pair to available devices. When pairing with a
smartphone, the JWM12A becomes "discoverable" by your smartphone and
can be paired using the phone menu.
2. When the Bluetooth device has completed its search, the mobile phone will
display the Bluetooth device name (JWM12A).
3. Select JWM12A.
4. Enter the pairing password (0000), if requested.
5. If successful, the unit will display "BT PAUSE".
After connecting successfully, you will be able to listen to audio from your
Bluetooth enabled device through the JWM12A.
About Bluetooth Technology
Bluetooth Menu Options
Pairing a Bluetooth
Bluetooth Audio(A2DP)
Selecting Tracks
Pausing Playback
VOLUME /
VOLUME /
VOLUME /
8
JWM12A
APP OPERATION SPECIFICATIONS
JENSEN® Specialty Controller is the ultimate wireless remote control for your
JENSEN stereo system. Store away your old remotes and enjoy the convenience
of all the primary functions of your JENSEN stereo right from your phone or tablet
by transforming your mobile device into a functional stereo remote control!
This app controls all of the primary functions of your stereo features including:
Ÿ Power on/off
Ÿ Volume and mute
Ÿ AM/FM radio tuner: access station, recall, store presets, switch songs
Ÿ Bluetooth® streaming audio
Ÿ Auxiliary audio input control –auxiliary analog 1 & 2, auxiliary digital coaxial,
auxiliary digital optical
Ÿ Speaker selection A and/or B
Ÿ Audio menu controls-bass, treble, balance, volume and speaker selection
settings
Ÿ Clock with sleep time and alarm
Ÿ Visual display feedback so you can see artist title and album on your mobile
screen
FEATURES
FCC Notice
Connecting and using jControl app
After downloading and installing jControl app on your apple device. pair your
device to the JWM12A as stated above for Bluetooth paring. Once your device is
paired you can open the app and use as instructed with the jControl app manual
found at
http://asaelectronics.com/manuals-guides.
When jControl is installed on Android operating system, close the app before
Bluetooth pairing, otherwise there may be errors on Bluetooth connection.
General
Power Supply Requirements . . . . . . . . . . . . . . . . . . . DC12 Volts, Negative Ground
Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-16 VDC
Overall Dimensions . . . . . . . . . . . . . . . . . . . . . .. . . . . . .10.4"(W) x 2.8"(H) x 3.6"(D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0 lbs. (0.39Kg)
FM Tuner
Tuner Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5-107.9 Mhz
Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . <5 μV
Stereo Separation @ 1kHz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >30 dB
AM Tuner
Tuner Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530-1710 kHz
Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30 μV
Amplifier
Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 x 6 Watts
per Channel
Output Impedance . . . Compatible with 4-8 ohms speakers, 4 ohm load minimum
Total System Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Watts Maximum
Specifications subject to change without notice.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment complied with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
9
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's
authority to operate the equipment.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Voyager JWM12A Owner's manual

Voyager
Brand
Voyager
Model
JWM12A
Category
Car media receivers
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents