Toro Power Max 828 LXE Snowthrower User manual

Brand: Toro

Model: Power Max 828 LXE Snowthrower

Category: Snow throwers

Type: User manual

Toro Power Max 828 LXE Snowthrower is a powerful machine designed to make snow removal a breeze. With its high-speed impeller and low-speed auger, it can easily handle even the heaviest snowfalls. The adjustable auger housing height allows you to clear a variety of surfaces, from gravel to crushed rock. The snowthrower also features a variety of safety features, including a safety alert symbol, rotating auger/impeller warning, and a shield to protect your hands and feet.

Form No. 3354-341 Rev B

Power Max® 828LXE Snowthrower

Model No. 38631 —Serial No. 260000001 and Up

Operator's Manual

Introduction

R ead this infor mation carefully to lear n ho w to operate and

maintain y our product properly and to a v oid injur y and

product damag e . Y ou are responsible for operating the

product properly and safely .

Y ou ma y contact T oro directly at www .T oro .com for

product and accessor y infor mation, help ﬁnding a dealer ,

or to register y our product.

W henev er y ou need ser vice , g en uine T oro par ts , or

additional infor mation, contact an A uthorized Ser vice

Dealer or T oro Customer Ser vice and ha v e the model and

serial n umbers of y our product ready . Figure 1 identiﬁes the

location of the model and serial n umbers on the product.

W rite the n umbers in the space pro vided.

Figure 1

1. Model and serial number location

Model No.

Serial No.

T his man ual identiﬁes potential hazards and has safety

messag es identiﬁed b y the safety aler t symbol ( Figure 2 ),

whic h signals a hazard that ma y cause serious injur y or

death if y ou do not follo w the recommended precautions .

Figure 2

1. Safety alert symbol

T his man ual uses 2 other w ords to highlight infor mation.

Impor tant calls attention to special mec hanical infor mation

and Note emphasizes g eneral infor mation w or th y of special

attention.

R eplacement Engine Owner’ s Man uals may be order ed

thr ough the engine man uf actur er .

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA

Safety

Bef or e Ope r a t ing

Ca u ti on : Im p r o p er u se ma y r e su lt

in lo ss o f fin g e r, h a n d s, o r fe e t.

Re a d a nd unders t a n d t he cont e n t s o f t hi s

manual b efo r e oper atin g t h e sn ow t hr o w e r.

Becom e fa m iliar wi t h a ll co n t r ols a n d kno w

ho w t o st o p t h e e ng ine q ui ckly.

Th e r e is a h ig h -sp e e d

im p e lle r clo se t o t h e

o p en in g .

Th e low -sp eed a ug e r h a s a m ovin g p in ch

po in t clo se t o t h e o pe n in g .

Oper at o r ’s

Posit ion

T his sno wthr o w er meets or ex ceeds the ISO standard

8437 in ef fect at the time of pr oduction.

R ead and under stand the contents of this man ual

bef or e the engine is ev er star ted.

T his is the safety aler t symbol. It is used to aler t y ou

to potential per sonal injur y hazards. Obey all safety

messa ges that f ollo w this symbol to a v oid possible

injur y or death.

Impr oper l y using or maintaining this sno wthr o w er

could r esult in injur y or death. T o r educe this potential,

compl y with the f ollo wing safety instr uctions.

T he follo wing instr uctions ha v e been adapted from the

ANSI/OPEI standard B71.3-1995 and the ISO 8437:1989

standard.

Training

• R ead the operator’ s man ual carefully . Be thoroughly

familiar with the controls and the proper use of the

equipment. Kno w ho w to stop the unit and diseng ag e

the controls quic kly .

• Nev er allo w c hildren to operate the sno wthro w er .

Nev er allo w adults to operate the sno wthro w er without

proper instr uction.

• K ee p the area of operation clear of all persons

(par ticularly small c hildren) and pets .

• Ex ercise caution to a v oid slipping or falling, especially

when operating the sno wthro w er in rev erse .

Preparation

• T horoughly inspect the area where y ou will use the

sno wthro w er . R emo v e all door mats , sleds , boards ,

wires , and other foreign objects .

• Before star ting the engine , diseng ag e all clutc hes . Shift

the sno wthro w er into neutral as w ell, if applicable .

• Do not operate the sno wthro w er without w earing

adequate winter g ar ments . W ear footw ear that will

impro v e y our footing on slipper y surfaces .

• Handle fuel with care; it is highly ﬂammable .

– Use an appro v ed fuel container .

– Nev er add fuel to a r unning or hot engine .

– Fill the fuel tank outdoors with extreme care . Nev er

ﬁll the fuel tank indoors .

– R e place the fuel tank cap securely and wipe up any

spilled fuel.

• Use only the po w er cord supplied with the sno wthro w er

and a rece ptacle appropriate for use with the po w er

cord for electric-star t motors .

• Adjust the aug er housing height to clear a g ra v el or

cr ushed-roc k surface .

• Nev er attempt to mak e any adjustments while the engine

is r unning, ex ce pt where speciﬁcally recommended b y

T oro .

• Let the engine and the sno wthro w er adjust to the

outdoor temperature before star ting to clear sno w .

• Operating any po w ered mac hine can result in foreign

objects being thro wn into the eyes . Alw a ys w ear safety

glasses or eye shields while operating, adjusting, or

re pairing the sno wthro w er .

Operation

• Do not put y our hands or feet near or under rotating

par ts . K ee p clear of the disc harg e opening at all times .

• Ex ercise extreme caution when crossing g ra v el dri v es ,

w alks , or roads . Sta y aler t for hidden hazards or trafﬁc .

• After striking a foreign object, stop the engine ,

disconnect the wire from the spark plug, thoroughly

inspect the sno wthro w er for any damag e , and re pair the

damag e before operating the sno wthro w er .

• If the unit should star t to vibrate abnor mally , stop the

engine and c hec k immediately for the cause . Vibration

is g enerally a w ar ning of trouble .

• Stop the engine whenev er y ou lea v e the operating

position, before unclog ging the aug er/impeller housing

or disc harg e c hute , and when making any re pairs ,

adjustments , or inspections .

• W hen cleaning, re pairing, or inspecting, mak e cer tain

that the aug er/impeller and all mo ving par ts ha v e

stopped. Disconnect the spark plug wire and k ee p the

wire a w a y from the spark plug to prev ent someone

from accidentally star ting the engine .

• Do not r un the engine indoors , ex ce pt when star ting

it and for mo ving the sno wthro w er in or out of the

building . Open the outside doors; exhaust fumes are

dang erous .

• Do not clear sno w across the face of slopes . Ex ercise

extreme caution when c hanging direction on slopes . Do

not attempt to clear stee p slopes .

• Nev er operate the sno wthro w er without proper guards

or other safety devices in place .

• Nev er operate the sno wthro w er near glass enclosures ,

automobiles , windo w w ells , and drop-offs without

properly adjusting the sno w disc harg e angle . K ee p

c hildren and pets a w a y .

• Do not o v erload the mac hine capacity b y attempting to

clear sno w at too fast a rate .

• Look behind and use care when bac king up with the

sno wthro w er .

• Nev er direct the disc harg e at b ystanders or allo w any one

in front of the unit.

• Diseng ag e the po w er to the aug er/impeller when the

sno wthro w er is being transpor ted or when not in use .

• Use only attac hments and accessories appro v ed b y

T oro , suc h as wheel w eights , counterw eights , and cabs .

(Contact an A uthorized Ser vice Dealer for accessories

a v ailable for y our sno wthro w er .)

• Nev er operate the sno wthro w er without g ood visibility

or light. Alw a ys be sure of y our footing, and k ee p a ﬁr m

hold on the handle . W alk; nev er r un.

Maintenance and Storage

• Chec k all fasteners at frequent inter v als for proper

tightness to be sure that the equipment is in safe

w orking condition.

• Nev er store the mac hine with fuel in the fuel tank inside

a building where ignition sources are present, suc h as

hot w ater and space heaters and clothes dr yers . Allo w

the engine to cool before storing in any enclosure .

• Alw a ys refer to this operator’ s man ual for impor tant

details if the sno wthro w er is to be stored for an

extended period.

• Maintain or re place safety and instr uction labels when

necessar y .

Toro Snowthrower Safety

T he follo wing list contains safety infor mation speciﬁc to

T oro products or other safety infor mation that y ou m ust

kno w .

• R otating auger/impeller can cut of f or injur e

ﬁnger s or hands. Sta y behind the handles and

a w a y from the disc harg e opening while operating the

sno wthro w er . K eep y our f ace, hands, feet, and an y

other par t of y our body or clothing a w ay fr om

mo ving or r otating par ts.

• Before adjusting, cleaning, inspecting, troubleshooting,

or re pairing the sno wthro w er , stop the engine, r emo v e

the k ey , and w ait f or all mo ving par ts to stop .

Disconnect the wir e fr om the spar k plug and k eep

it a w ay fr om the spar k plug to pr ev ent someone

fr om accidentall y star ting the engine.

• T o unclog the disc harg e c hute , sta y in the operating

position and release the left hand (traction) lev er . W hile

r unning the aug er/impeller , push do wn on the handles

to raise the front of the sno wthro w er a few inc hes

(centimeters) off the pa v ement. T hen lift the handles

quic kly to bump the front of the sno wthro w er on the

pa v ement. R e peat if necessar y until a stream of sno w

comes out the disc harg e c hute .

• If y ou cannot unclog the disc harg e c hute b y bumping

the front of the sno wthro w er , stop the engine, w ait

f or all mo ving par ts to stop , and use a stick; nev er

use y our hand.

• Do not w ear loose-ﬁtting clothing that could g et caught

in mo ving par ts .

• If a shield, safety device , or decal is damag ed, illegible ,

or lost, re pair or re place it before beginning operation.

• Do not smok e while handling g asoline .

• Do not touc h the engine while it is r unning or soon

after it has stopped because the engine ma y be hot

enough to cause a bur n.

• W hen storing the sno wthro w er for more than 30 da ys ,

drain the fuel from the fuel tank to prev ent a potential

hazard. Store fuel in an appro v ed fuel container .

R emo v e the k ey from the ignition switc h before storing

the sno wthro w er .

• Purc hase only g en uine T oro re placement par ts and

accessories .

Sound Pressure

T his unit has a maxim um sound pressure lev el at the

operator’ s ear of 92 dB A, based on measurements of

identical mac hines per EN 11201.

Sound Power

T his unit has a guaranteed sound po w er lev el of 108 dB A,

based on measurements of identical mac hines per EN 3744.

Vibration

T his unit does not ex ceed a hand/ar m vibration lev el of

7.0 m/s

, based on measurements of identical mac hines

per EN 1033.

Safety and Instructional Decals

Important: Safety and instr uction decals ar e located near ar eas of potential danger . R eplace dama ged decals.

108-2968

1. Left turn control

4. Warning—Read the Operator’s Manual .

7. Auger drive

2. Wheel drive 5. Cutting dismemberment, impeller

hazard—Stop the engine before leaving the

operating position and do not place your

hand in the chute.

8. Right turn control

3. Engage

6. Thrown object hazard—Keep bystanders a

safe distance from the hazardous location.

9. Read the Operator’s Manual .

106-4525

Reorder part no. 107-3825

1. Fast

3. Slow

2. Forward speeds 4. Reverse speeds

106-7309

1. Cutting/dismemberment hazard, impeller—stop the engine

before leaving the operating position and do not place your hand

in the chute.

107-3040

1. Cutting dismemberment, impeller and cutting dismemberment,

auger hazards—keep bystanders a safe distance from the

snowthrower.

1. Warning—hot surface, do not touch

Tecumseh Part No. 36501

1. Primer

Tecumseh Part No. 35077

1. Key ignition

5. Increasing scale

2. Engage to start the engine 6. Slow

3. Disengage to stop the engine 7. Stop the engine

4. Fast

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

Handle bolts

Curved washers

Locknuts

Install the upper handle.

No parts required

–

Install the wheel clutch cable ends

No parts required

–

Install the traction control linkage.

Carriage bolts

Locknuts

Install the chute control rod.

Cable ties

Connect the wire to the headlight.

No parts required

–

Fill the engine with oil.

No parts required

–

Check the tire pressure.

No parts required

–

Check the skids and scraper.

1. Installing the Upper Handle

Note: Do not remo v e the r ubber band until y ou ha v e

installed the upper handle .

1. Lift and rotate the upper handle and position it o v er

the lo w er handle ( Figure 3 ).

Important: R oute the ca bles attached to the

Quick Stick inside the upper handle legs and

ensur e that the ca bles and the wir e f or the headlight

ar e not pinched betw een the handle sections.

Figure 3

1. Cables

2. Secure the upper handle with 4 handle bolts , 4 cur v ed

w ashers , and 4 loc kn uts from the loose par ts bag ( Figure

4 ).

Figure 4

2. Installing the Wheel Clutch

Cable Ends

1. Unwrap the cable ends from the lo w er handle ( Figure 5 ).

Figure 5

2. R oute either the left or right cable end o v er the lo w er

handle and inser t the cable end into the hole in the

cor responding wheel clutc h lev er ( Figure 6 ).

Figure 6

1. Wheel clutch lever

3. R emo v e the n ut and w asher from the handle , attac h

the cable clamp on the cable to the handle , and hand

tighten the n ut ( Figure 7 ).

Figure 7

1. Cable clamp

Important: Ensur e that the cur v ed side of the

ca ble clamp is a gainst the handle and that the ca ble

is r outed belo w the clamp bolt. T he ca ble must be

in a straight line fr om the ca ble clamp to the point

wher e it attaches to the wheel clutch lev er .

4. Pull the cable jac k et do wn g ently until the wheel clutc h

lev er is do wn and the slac k is out of the cable , then

tighten the cable clamp n ut securely ( Figure 8 ).

Figure 8

5. Squeeze the lev er fully , then c hec k the g ap betw een

the bottom of the handle and the wheel clutc h lev er

end ( Figure 9 ).

Figure 9

Note: T he g ap should be appro ximately the thic kness

of a pencil (1/4 inc h or 6 mm). If it is g reater , loosen

the cable clamp n ut, slide the cable jac k et up slightly ,

tighten the cable clamp n ut, and c hec k the g ap ag ain.

6. R e peat ste ps 2 through 5 for the other cable .

3. Installing the Traction

Control Linkage

1. R emo v e the hair pin cotter and w asher from the lo w er

end of the speed control rod and inser t the lo w er end

of the rod into the lo w er link ar m so that the bent end

of the speed control rod faces rearw ard ( Figure 10 ).

Figure 10

2. Secure the lo w er end of the speed control rod with the

w asher and hair pin cotter that y ou previously remo v ed.

3. R emo v e the hair pin cotter and the outer w asher from

the tr unnion on the upper end of the speed control rod

( Figure 11 ).

Figure 11

1. Speed selector lever

3. Trunnion

2. Wave washer 4. Flat washer

Note: T o mak e installation easier , lea v e the w a v e

w asher and the ﬂat w asher on the tr unnion ( Figure 11 ).

4. Shift the speed selector lev er into P osition R2.

5. R otate the lo w er link ar m fully upw ard

(countercloc kwise) ( Figure 12 ).

Figure 12

6. Lift up on the speed control rod and inser t the tr unnion

into the hole in the speed selector lev er ( Figure 11 ).

Note: If the tr unnion does not ﬁt into the hole when

y ou lift up on the speed control rod, rotate the tr unnion

upw ard or do wnw ard on the speed control rod until

it ﬁts .

7. Secure the tr unnion and upper end of the speed control

rod with the outer w asher and a hair pin cotter y ou

previously remo v ed.

Note: F or easier installation, look do wn through the

opening in the speed selector ( Figure 13 ).

Figure 13

1. Speed selector

4. Installing the Chute Control

Rod

1. Unwrap the Quic k Stic k and rotate it so that it is upright

and in the center .

2. Hold the blue trig g er cap do wn and pull the lev er fully

rearw ard.

Note: T he disc harg e c hute and deﬂector should face

forw ard. If they do not, hold the blue trig g er cap

do wn (but do not mo v e the Quic k Stic k) and rotate the

disc harg e c hute until they do .

3. Align the ﬂattened bac k end of the long c hute control

rod with the ﬂattened front end of the shor t rod

that extends from the control panel so that they nest

tog ether ( Figure 14 ).

Figure 14

1. Short rod 2. Long chute control rod

4. Inser t the front end of the rod into the opening in the

bac k of the c hute g ear co v er until it slides into the c hute

g ear ( Figure 15 ).

Figure 15

5. Align the holes in the nested ends of the rods and inser t

2 car riag e bolts (in the loose par ts bag) through the

shor t rod from the left side of the sno wthro w er (from

the operating position).

6. Inser t the cable clip that suppor ts the deﬂector cable

onto the forw ard car riag e bolt, and secure the car riag e

bolts with loc kn uts from the loose par ts bag ( Figure 16 ).

Figure 16

1. Cable clip 2. Deector cable

7. Hold the blue trig g er cap do wn and rotate the Quic k

Stic k in a circle to ensure that the c hute and deﬂector

operate smoothly .

5. Connecting the Wire to the

Headlight

1. Inser t the wire connector on the loose end of the wire

straight into the bac k of the headlight until it is securely

in place ( Figure 17 ).

Figure 17

1. Plastic clip on wire

connector

3. Cable tie

2. U-bolt

Note: Ensure that the plastic clip on the wire

connector is on the bottom ( Figure 17 ).

2. Secure a cable tie (from the loose par ts bag) around the

wire and the handle about an inc h (2.5 cm) belo w the

U-bolt ( Figure 17 ).

6. Filling the Engine with Oil

Y our sno wthro w er comes with 26 oz. of oil in the engine .

Note: Before star ting the engine , c hec k the oil lev el and

add oil if necessar y .

Max. ﬁll: 26 oz. (0.77 l), type: automoti v e deterg ent oil with

an API ser vice classiﬁcation of SF , SG , SH, SJ , SL, or higher .

• F or temperatures abo v e 32°F (0°C), use SAE 30W .

• F or temperatures betw een 0°F and 32°F (-18°C to 0°C),

use SAE 5W30 or SAE 10W .

• F or air temperatures belo w 0°F (-18°C), use SAE 0W30.

1. R emo v e the dipstic k and slo wl y pour oil into the oil

ﬁll tube to raise the oil lev el to the Full mark on the

dipstic k. Do not o v erﬁll. ( Figure 18 ).

Figure 18

2. Install the dipstic k securely .

Note: Do not spill oil around the oil ﬁll tube; oil could

leak onto traction par ts and cause the traction to slip .

7. Checking the Tire Pressure

T he tires are o v erinﬂated at the factor y for shipping . R educe

the pressure equally in both tires to betw een 17 and 20 psi

(116 and 137 kP a).

8. Checking the Skids and

Scraper

R efer to Chec king and Adjusting the Skids and Scraper in

Maintenance .

Product Overview

Figure 19

1. Auger/impeller lever 8. Engine oil ll tube/dipstick

2. Speed selector lever 9. Chute deector

3. Quick Stick™ discharge chute

control

10. Discharge chute

4. Traction lever 11. Fuel shutoff valve

5. Wheel clutch lever (2) 12. Skid (2)

6. Headlight

13. Auger

7. Fuel tank

14. Scraper

Figure 20

1. Ignition switch

4. Primer

2. Choke 5. Electric starter

3. Throttle 6. Recoil starter

Operation

Note: Deter mine the left and right sides of the mac hine

from the nor mal operating position.

Freewheeling or Using the

Self-propel Drive

Y ou can operate the sno wthro w er with the self-propel

feature eng ag ed or diseng ag ed (freewheeling).

T o freewheel, slide the wheels inw ard and inser t the axle

pins through the outer axle holes , but not through the wheel

hubs ( Figure 21 ).

Figure 21

T o self-propel, slide the wheels outw ard and inser t the axle

pins through the holes in the wheel hubs and the inner axle

holes ( Figure 22 ).

Figure 22

Filling the Fuel Tank

Gasoline is extr emel y ﬂamma ble and explosi v e. A

ﬁr e or explosion fr om gasoline can bur n y ou and

other s.

• T o pr ev ent a static charge fr om igniting the

gasoline, place the container and/or sno wthr o w er

on the g r ound bef or e ﬁlling , not in a v ehicle or

on an object.

• Fill the tank outdoor s when the engine is cold.

W ipe up spills.

• Do not handle gasoline when smoking or ar ound

an open ﬂame or spar ks.

• Stor e gasoline in an appr o v ed fuel container , out

of the r each of childr en.

Fill the fuel tank with fresh unleaded regular g asoline from

a major name-brand ser vice station ( Figure 23 ).

Important: T o r educe star ting pr oblems, add fuel

sta biliz er to the fuel all season, mixing it with gasoline

less than 30 days old. Do not add oil to the gasoline.

Figure 23

1. 1/2 inch (1.3 cm)

Starting the Engine

1. Connect the spark plug wire ( Figure 24 ).

Figure 24

2. Mo v e the throttle to the F ast position ( Figure 25 ).

Figure 25

3. R otate the fuel shutoff v alv e countercloc kwise to open

it ( Figure 26 ).

Figure 26

4. R otate the c hok e to the On position ( Figure 27 ).

Figure 27

5. Inser t the ignition k ey ( Figure 28 ).

Figure 28

6. Fir mly push in the primer 3 times with y our thumb ,

holding the primer in for a second before releasing it

eac h time ( Figure 29 ).

Figure 29

Note: T ak e y our glo v e off when y ou push in the

primer so that air cannot escape from the primer hole .

Note: Priming ex cessi v ely ma y ﬂood the engine and

prev ent it from star ting .

7. Star t the sno wthro w er using the recoil star ter or the

electric star ter ( Figure 30 ).

Figure 30

Important: T o pr ev ent dama ging the electric

star ter , r un it no mor e than 10 times at inter v als

of 5 seconds on, then 5 seconds of f. If the engine

does not star t after this series of attempts, allo w the

star ter to cool f or at least 40 min utes bef or e tr ying

to star t it a gain. If the engine still does not star t,

tak e the sno wthr o w er to an Authoriz ed Ser vice

Dealer f or ser vice.

8. Disconnect the cord from the electric star ter and the

outlet.

9. W hen the engine star ts , set the c hok e to the

3/4 position. As the engine w ar ms up , set the c hok e

to the 1/2 position. W hen the engine is w ar m, set the

c hok e to the Off position.

If y ou lea v e the sno wthr o w er plug ged into a

po w er outlet, someone can inadv er tentl y star t

the sno wthr o w er and injur e people or dama ge

pr oper ty .

Unplug the po w er cord whenev er y ou ar e not

star ting the sno wthr o w er .

Stopping the Engine

1. Mo v e the throttle to the Stop position ( Figure 31 ).

Figure 31

2. W ait for all mo ving par ts to stop before lea ving the

operating position.

3. Close the fuel shutoff v alv e b y rotating it cloc kwise

( Figure 32 ).

Figure 32

4. Pull the recoil star ter 3 or 4 times . T his helps prev ent

the recoil star ter from freezing up .

Operating the Traction Drive

Important: T o operate the traction dri v e, y ou

must operate the sno wthr o w er with the self-pr opel

featur e enga ged. R efer to F r eewheeling or Using the

Self-pr opel Dri v e.

1. T o eng ag e the traction dri v e , squeeze the left hand

(traction) lev er to the handg rip ( Figure 33 ).

Figure 33

2. T o stop the traction dri v e , release the traction lev er .

3. Chec k to ensure that the speed selector operates

properly:

• If the sno wthro w er does not mo v e or mo v es

forw ard when it is in P osition R1, remo v e the

tr unnion from the speed selector lev er , tur n the

tr unnion do wnw ard (cloc kwise) on the speed

control rod, then install the tr unnion.

• If the sno wthro w er does not mo v e or mo v es

rearw ard when it is in P osition 1 (forw ard), remo v e

the tr unnion from the speed selector lev er , tur n the

tr unnion upw ard (countercloc kwise) on the speed

control rod, then install the tr unnion.

Note: R efer to Installing the T raction Control

Linkag e .

Note: If the sno wthro w er mo v es when the

traction lev er is in the released position, c hec k the

traction cable (refer to Chec king and Adjusting

the T raction Cable) or tak e the sno wthro w er to an

A uthorized Ser vice Dealer for ser vice .

Using the Wheel Clutch Levers

T he wheel clutc h lev ers allo w y ou to momentarily diseng ag e

the dri v e to one or both wheels with the traction dri v e lev er

still eng ag ed. T his enables y ou to tur n and maneuv er the

sno wthro w er easily .

Note: Holding do wn the traction lev er ag ainst the handle

eng ag es the traction dri v e to both wheels .

T o tur n the sno wthro w er to the right, lift up on the right

wheel clutc h lev er and squeeze it to w ard the handle ( Figure

34 ).

Figure 34

Note: T his diseng ag es the dri v e to the right wheel while

the left wheel contin ues dri ving, and the sno wthro w er tur ns

to the right.

Note: Similarly , squeezing the left wheel clutc h lev er tur ns

the sno wthro w er to the left.

W hen y ou complete the tur n, release the wheel clutc h lev er ,

and the dri v e re-eng ag es both wheels ( Figure 35 ).

Figure 35

Momentarily squeezing and releasing the left or right wheel

clutc h lev er also allo ws for steering adjustments to k ee p the

sno wthro w er g oing in a straight line , especially in dee p sno w .

Squeezing both wheel clutc h lev ers sim ultaneously

diseng ag es the dri v e to both wheels . T his enables y ou

to man ually mo v e the sno wthro w er bac kw ard without

stopping to shift it into a rev erse g ear . It also allo ws y ou to

maneuv er and transpor t the sno wthro w er more easily when

the engine is not r unning .

Operating the Speed Selector

T he speed selector has 6 forw ard and 2 rev erse g ears . T o

c hang e speeds , release the traction lev er and shift the speed

selector lev er to the desired position ( Figure 36 ). T he lev er

loc ks in a notc h at eac h speed selection.

Figure 36

Operating the Auger/Impeller

Drive

1. T o eng ag e the aug er/ impeller dri v e , squeeze the right

hand (aug er/ impeller) lev er to the handg rip ( Figure 37 ).

Figure 37

2. T o stop the aug er and impeller , release the right hand

lev er .

Important: W hen y ou enga ge both the

auger/impeller lev er and the traction lev er , the

traction lev er locks the auger/impeller lev er do wn,

fr eeing y our right hand. T o r elease both lev er s,

simpl y r elease the left hand (traction) lev er .

3. If the aug er and impeller contin ue to rotate when y ou

release the aug er/impeller lev er , do not operate the

sno wthro w er . Chec k the aug er/impeller cable (refer to

Chec king and Adjusting the A ug er/Impeller Cable) and

adjust it if necessar y . Otherwise , tak e the sno wthro w er

to an A uthorized Dealer for ser vice .

If the auger and impeller contin ue to r otate when

y ou r elease the auger/impeller lev er , y ou could

seriousl y injur e y our self or other s.

Do not operate the sno wthr o w er . T ak e it to an

Authoriz ed Ser vice Dealer f or ser vice.

Operating the Quick Stick™

Hold the blue trig g er cap do wn to use the Quic k Stic k to

mo v e the disc harg e c hute and the c hute deﬂector . R elease

the trig g er cap to loc k the disc harg e c hute and c hute

deﬂector into position ( Figure 38 ).

Figure 38

Moving the Discharge Chute

Hold the blue trig g er cap do wn and mo v e the Quic k Stic k

to the left to mo v e the disc harg e c hute to the left; mo v e

the Quic k Stic k to the right to mo v e the disc harg e c hute to

the right ( Figure 39 ).

Figure 39

• If the c hute does not mo v e , refer to Adjusting the

Disc harg e Chute Latc h.

• If the c hute does not tur n as far to the left as it does to

the right, ensure that the cable is routed to the inside of

the handles . R efer to Installing the Upper Handle .

• If the c hute does not loc k into place when y ou release

the trig g er cap , refer to Adjusting the Disc harg e Chute

Latc h.

Moving the Chute Deector

Hold the blue trig g er cap do wn and mo v e the Quic k Stic k

forw ard to lo w er the c hute deﬂector; mo v e it rearw ard to

raise the c hute deﬂector ( Figure 40 ).

Figure 40

Unclogging the Discharge

Chute

If the aug er/impeller is r unning but there is no sno w

coming out of the disc harg e c hute , the disc harg e c hute ma y

be clog g ed.

• T o unclog the disc harg e c hute , sta y in the operating

position and release the left hand (traction) lev er . W hile

r unning the aug er/impeller , push do wn on the handles

to raise the front of the sno wthro w er a few inc hes

(centimeters) off the pa v ement. T hen lift the handles

quic kly to bump the front of the sno wthro w er on the

pa v ement. R e peat if necessar y until a stream of sno w

comes out the disc harg e c hute .

• If y ou cannot unclog the disc harg e c hute b y bumping

the front of the sno wthro w er , stop the engine, w ait

f or all mo ving par ts to stop , and use a stick; nev er

use y our hand.

Important: Unclo g ging the discharge chute

by bumping the fr ont of the sno wthr o w er on the

pa v ement may cause the skids to mo v e. Adjust the

skids and tighten the skid bolts secur el y .

Preventing Freeze-up

• In sno wy and cold conditions , some controls and

mo ving par ts ma y freeze . Do not use ex cessi v e f orce

when tr ying to operate fr oz en contr ols. If y ou ha v e

difﬁculty operating any control or par t, star t the engine

and let it r un for a few min utes .

• After using the sno wthro w er , let the engine r un for

a few min utes to prev ent mo ving par ts from freezing .

Eng ag e the aug er/impeller to clear any remaining sno w

from inside the housing . R otate the Quic k Stic k to

prev ent it from freezing . Stop the engine , w ait for all

mo ving par ts to stop , and remo v e all ice and sno w from

the sno wthro w er .

• With the engine off , pull the recoil star ter handle sev eral

times to prev ent the recoil star ter from freezing up .

Operating Tips

W hen the sno wthr o w er is in operation, the impeller

and auger can r otate and cut of f or injur e hands and

feet.

• Bef or e adjusting , cleaning , inspecting ,

tr oubleshooting , or r epairing the sno wthr o w er ,

stop the engine and w ait f or all mo ving par ts

to stop . Disconnect the wir e fr om the spar k

plug and k eep it a w ay fr om the plug to pr ev ent

someone fr om accidentall y star ting the engine.

• R emo v e an obstr uction fr om the discharge chute;

r efer to Unclo g ging the Discharge Chute. If

necessar y , use a stick, not y our hands, to r emo v e

an obstr uction fr om the discharge chute.

• Stay behind the handles and a w ay fr om

the discharge opening while operating the

sno wthr o w er .

• K eep f ace, hands, feet, and an y other par t of y our

body or clothing a w ay fr om concealed, mo ving ,

or r otating par ts.

T he r otor blades can thr o w stones, toys, and other

f or eign objects and cause serious per sonal injur y to

the operator or to bystander s.

• K eep the ar ea to be clear ed fr ee of all objects that

the r otor blades could pick up and thr o w .

• K eep all childr en and pets a w ay fr om the ar ea

of operation.

• Alw a ys set the throttle to the F ast position when

thro wing sno w .

• If the engine slo ws do wn under a load or the wheels

slip , shift the sno wthro w er into a lo w er g ear .

• If the front of the sno wthro w er rides up , shift the

sno wthro w er into a lo w er g ear . If the front contin ues to

ride up , lift up on the handles .

Maintenance

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the rst 2 operating

hours

• Inspect the traction cable and adjust it if necessary.

• Inspect the auger/impeller cable and adjust it if necessary.

• Change the engine oil.

Before each use or daily

• Check the engine oil level and add oil if necessary.

Yearly

• Check the skids and the scraper and adjust them if necessary.

• Inspect the traction cable and adjust or replace it if necessary.

• Inspect the auger/impeller cable and adjust or replace it if necessary.

• Check the auger gearbox oil and add oil if necessary.

• Change the engine oil.

• Lubricate the hex shaft.

• Inspect the spark plug. Replace and/or gap it if necessary.

Yearly or before storage

• Check the air pressure in the tires and inate them to 17–20 psi (116–137 kPa).

• Drain the gasoline and run the engine to dry out the fuel tank and the carburetor

at the end of the season.

• Have an Authorized Service Dealer inspect and replace the traction drive belt

and/or the auger/impeller drive belt, if necessary.

Important: Y ou can ﬁnd mor e inf or mation a bout maintaining and ser vicing y our sno wthr o w er at

www .T or o.com.

Important: R efer to y our engine operator’ s man ual f or additional maintenance pr ocedur es. F or engine

adjustments, r epair s, or w ar ranty ser vice not co v er ed in this man ual, contact an Authoriz ed T ecumseh Ser vicing

Dealer .

Preparing for Maintenance

1. Mo v e the sno wthro w er to a lev el surface .

2. Stop the engine and w ait for all mo ving par ts to stop .

3. Disconnect the spark plug wire ( Figure 41 ).

Figure 41

Checking the Engine Oil Level

Eac h time before using the sno wthro w er , c hec k the oil lev el

in the engine crankcase .

1. R emo v e the dipstic k, wipe it clean, then fully install the

dipstic k.

2. R emo v e the dipstic k and c hec k the oil lev el ( Figure 42 ).

If the oil lev el is belo w the Add mark on the dipstic k,

add oil. R efer to Filling the Engine with Oil.

Figure 42

Checking and Adjusting the

Skids and Scraper

Chec k the skids and the scraper to ensure that the aug er

does not contact the pa v ed or g ra v el surface . Adjust the

skids and the scraper as needed to compensate for w ear .

1. Chec k the tire pressure . R efer to Chec king the Tire

Pressure .

2. Loosen the n uts that secure both skids to the aug er

sides until the skids slide up and do wn easily ( Figure 43 ).

Figure 43

1. 1/2 inch (1.3 cm)

3. Suppor t the side plates so that they are at least 1/2 inc h

(1.3 cm) abo v e a lev el surface .

Important: T he auger blades must be suppor ted

a bo v e the g r ound by the skids.

4. Ensure that the scraper is 1/8 inc h (3 mm) abo v e and

parallel to a lev el surface .

Note: If the pa v ement is crac k ed, rough, or unev en,

adjust the skids to raise the scraper . F or g ra v el

surfaces , adjust the skids fur ther do wn to prev ent the

sno wthro w er from pic king up roc ks .

5. Mo v e the skids do wn until they are ev en with the

g round.

6. Fir mly tighten the n uts that secure both skids to the

aug er sides .

Note: T o quic kly adjust the skids if they loosen,

suppor t the scraper 1/8 inc h (3 mm) off the pa v ement,

then adjust the skids do wn to the pa v ement.

Note: If the skids become ex cessi v ely w or n, y ou can

tur n them o v er and set the un used side to w ard the

pa v ement.

Checking and Adjusting the

Traction Cable

Chec k and adjust the traction cable after the ﬁrst 2 operating

hours , then yearly thereafter . If the sno wthro w er does not

dri v e in the forw ard or rev erse speeds or it dri v es when y ou

release the traction lev er , adjust the traction cable .

With the traction lev er diseng ag ed, c hec k the pin in the

elong ated slot in the left side of the sno wthro w er abo v e

the tire . T here should be a g ap of 1/32 to 1/16 inc h (1 to

1.5 mm) from the front of the slot to the front edg e of the

pin ( Figure 44 ).

Figure 44

1. Pin

2. 1/32 to 1/16 inch (1 to 1.5 mm)

If the left hand (traction) cable is not properly adjusted,

do the follo wing ste ps:

1. Loosen the jam n ut.

2. Loosen or tighten the tur nbuc kle to adjust the pin until

it is the proper g ap from the front edg e of the slot.

3. Tighten the jam n ut ( Figure 45 ).

Figure 45

1. Jam nut

2. Turnbuckle

Checking and Adjusting the

Auger/Impeller Cable

Chec k and adjust the aug er/impeller cable after the ﬁrst

2 operating hours , then yearly thereafter .

1. R emo v e the 2 screws from the right side of the belt

co v er as sho wn.

2. Lift up the right side of the belt co v er ( Figure 46 ).

Figure 46

3. With the aug er/impeller lev er diseng ag ed, ensure that

the g ap betw een the aug er clutc h assembly and the tab

is 1/16 inc h (1.5 mm) ( Figure 47 ).

Figure 47

1. Tab

2. 1/16 inch (1.5 mm)

4. If the aug er/impeller cable is not properly adjusted, do

the follo wing ste ps:

5. Loosen the jam n ut ( Figure 48 ).

Figure 48

1. Jam nut

2. Turnbuckle

6. Loosen or tighten the tur nbuc kle that adjusts the

tension on the cable ( Figure 48 ).

7. Adjust the tur nbuc kle until y ou obtain the proper g ap .

8. Tighten the jam n ut.

9. Inser t the 2 screws y ou previously remo v ed on the belt

co v er .

10. If the aug er/impeller cable is properly adjusted but a

problem remains , contact an A uthorized Ser vice Dealer .

Checking the Auger Gearbox

Oil Level

Chec k the aug er g earbo x oil yearly and add oil if necessar y .

1. Mo v e the sno wthro w er to a lev el surface .

2. Clean the area around the pipe plug ( Figure 49 ).

Figure 49

3. R emo v e the pipe plug from the g earbo x.

4. Chec k the oil lev el in the g earbo x. T he oil should be at

the point of o v erﬂo wing at the ﬁller opening .

5. If the oil lev el is lo w , add GL-5 or GL-6, SAE 85-95

EP transmission oil to the g earbo x until the point of

o v erﬂo w .

Note: Do not use synthetic oil.

6. Install the pipe plug in the g earbo x.

Changing the Engine Oil

Chang e the engine oil after the ﬁrst 2 operating hours , then

yearly thereafter . If possible , r un the engine just before

c hanging the oil because w ar m oil ﬂo ws better and car ries

more contaminants .

Max. ﬁll: 26 oz. (0.77 l), type: automoti v e deterg ent oil with

an API ser vice classiﬁcation of SF , SG , SH, SJ , SL, or higher .

• F or temperatures abo v e 32°F (0°C), use SAE 30W .

• F or temperatures betw een 0°F and 32°F (-18°C to 0°C),

use SAE 5W30 or SAE 10W .

• F or air temperatures belo w 0°F (-18°C), use SAE 0W30.

1. Clean the area around the oil drain cap ( Figure 50 ).

Figure 50

1. Oil drain cap

2. Slide an oil drain pan under the drain extension and

remo v e the oil drain cap .

3. Drain the oil.

Note: Dispose of the used oil properly at a local

recycling center .

4. Install the oil drain cap .

5. Fill the crankcase with oil. R efer to Filling the Engine

Crankcase with Oil.

Lubricating the Hex Shaft

Lightly lubricate the hex shaft yearly with automoti v e engine

oil ( Figure 51 ).

Figure 51

1. Hex shaft 3. Rubber wheel

2. Aluminum friction plate

Important: Do not get oil on the r ub ber wheel or

the alumin um friction dri v e plate because the traction

dri v e will slip ( Figur e 51 ).

1. Drain the g asoline from the fuel tank.

2. Tip the sno wthro w er forw ard onto its aug er housing

and bloc k it so that it cannot fall.

3. R emo v e the bac k co v er ( Figure 52 ).

Figure 52

1. Back cover

4. Mo v e the speed selector lev er to P osition R2.

5. Dip y our ﬁng er in automoti v e engine oil and lightl y

lubricate hex shaft.

6. Mo v e the speed selector lev er to P osition 6.

7. Lubricate the other end of the hex shaft.

8. Mo v e the speed selector lev er forw ard and rearw ard

a few times .

9. Install the bac k co v er and retur n the sno wthro w er to

the operating position.

Inspecting and Replacing the

Spark Plug

Use a Champion RJ-19LM or equi v alent spark plug . Chec k

and g ap the spark yearly , and re place the plug if necessar y .

1. Clean around the base of the spark plug .

2. R emo v e the spark plug .

3. Examine the spark plug and re place it if it is crac k ed,

fouled, dir ty , or if the electrodes are w or n.

Important: Do not clean the electr odes because

g rit could enter the cylinder and dama ge the

engine.

4. Set the g ap betw een the electrodes on the spark plug at

0.030 inc h (0.76 mm) ( Figure 53 ).

Figure 53

1. 0.030 inch (0.76 mm)

5. Install the spark plug b y hand and then tor que it to 15

ft-lb (20.4 N·m).

Note: If y ou do not ha v e a tor que wrenc h, tighten

the plug ﬁr mly .

Adjusting the Discharge Chute

Latch

If the disc harg e c hute does not loc k into the desired

position or does not unloc k so that y ou can mo v e it to

another position, adjust the disc harg e c hute latc h.

1. R emo v e the fastener on the g ear co v er ( Figure 54 ), lift

the front of the co v er up , and slide it bac k and out of

the w a y .

Figure 54

2. Loosen the bolt on the cable clamp ( Figure 55 ).

Figure 55

1. Cable conduit 2. Cable clamp

3. Grasp the cable conduit and mo v e it to w ard the front of

the mac hine until the disc harg e c hute latc h fully eng ag es

the g ear teeth ( Figure 55 and Figure 56 ).

Figure 56

1. Discharge chute latch 2. Gear teeth

Note: T he latc h is spring loaded and will naturally

mo v e into the teeth of the g ear ( Figure 56 ).

4. R emo v e any slac k in the cable b y pulling the cable

conduit rearw ard.

5. Tighten the bolt on the cable clamp .

6. Install and secure the g ear co v er .

Page is loading ...

Toro Power Max 828 LXE Snowthrower User manual

Brand: Toro

Model: Power Max 828 LXE Snowthrower

Category: Snow throwers

Type: User manual

Download PDF

report

Toro Power Max 828 LXE Snowthrower User manual

Toro Power Max 828 LXE Snowthrower User manual

Related papers

Other documents