Briteq Led Power Beam BRITEQ Owner's manual

Brand: Briteq

Model: Led Power Beam BRITEQ

Category: Stroboscopes & disco lights

Type: Owner's manual

Briteq Led Power Beam BRITEQ is a versatile lighting fixture suitable for indoor or outdoor use, providing wash or effect lighting for architectural, stage, or nightclub applications. It can also be used for signage and advertising, thanks to its dynamic functions accessible via DMX512 control. Multiple units can be connected for larger applications.

The fixture features RGB dimming, strobe effects, and automatic programs, all controllable via DMX512 or the included PiX controller.

PART 5 USING THE CONTROLLER.............................................24.

5.1--BASIC.......................................................................................25.

5.3--MENU.......................................................................................27.

5.2--SETTING UP.............................................................................27.

PART 4 USING A DMX512 CONTROLLER....................................19.

4.1--BASIC ADDRESSING.................................................................20.

4.2--CHANNEL ASSIGNMENT............................................................20.

4.3--BASIC INSTRUCTIONS FORDMX512 OPERATION......................23.

PART 3 DISPLAY PANEL OPERATION.......................................13.

3.1--BASIC........................................................................................14.

3.2--MENU........................................................................................15.

3.3--CREATING ASTATIC COLOR......................................................16.

3.4--DMX512 SETTINGS....................................................................16.

3.5--ACTIVATINGAN AUTOPROGRAM..............................................17.

3.6--CHANGING THE SETTINGS........................................................17.

3.7--ACTIVATE THE PASSWORD.......................................................18.

3.8--POWER ON/OFF.........................................................................18.

3.9--RGB CHANNEL MODEL .............................................................18.

TABLE OF CONTENTS..................................................................I.

PART 1 PRODUCT (GENERAL)....................................................1.

1.1--PRODUCT INTRODUCTION.........................................................2.

1.2--PRODUCT FEATURES.................................................................2.

1.3--TECHNICAL SPECIFICATIONS.....................................................3.

1.4--PHOTOMETRIC DATA..................................................................4.

1.5--SAFETY WARNING......................................................................5.

PART 2 INSTALLATION...............................................................6.

2.1--MOUNTING...................................................................................7.

2.3--SETTING UPWITH A DMX512 CONTROLLER.................................8.

2.3-1--DMX512 ADDRESSING WITHOUTID ADDRESSING......................................8.

2.3-2--DMX512 ADDRESSING WITHID ADDRESS..................................................8.

2.4--SETTING UPWITH THE PiXCONTROLLER...................................9.

2.4-1--SINGLE ROWAPPLICATION.........................................................................9.

2.4-2--STANDARD BLOCKAPPLICATION..............................................................10.

2.4-3--REPEAT ROW BLOCKAPPLICATION...........................................................11.

2.5--OPERATIONWITH DMX512 VsPiX CONTROLLER.......................12.

2.2--POWER CONNECTION..................................................................7.

5.4--CUSTOM PROGRAM..................................................................28.

5.5--PLAY SCHEDULE......................................................................29.

5.6--CLOCK.....................................................................................29.

5.7--SCHEDULE...............................................................................29.

5.8--SETTINGS................................................................................30.

5.9--ACTIVATETHE PASSWORD.......................................................31.

5.10--PIX CONTROLLEREXTERNAL CONTROL VIADMX512.............31.

5.11--MAINTENANCE........................................................................33.

ABLE OF CONTENTS

TABLE OF CONTENTS I

2007.03.10

1.1 PRODUCT INTRODUCTION

1.2 PRODUCT FEATURES

1.3 TECHNICAL SPECIFICATIONS

1.4 PHOTOMETRIC DATA

1.5 SAFETY WARNING

PRODUCT (GENERAL)

1 PRODUCT(GENERAL) 1

2007.03.10

1.1 PRODUCT INTRODUCTION

This product is designed for indoor or outdoor use. Suitable applications include wash or

effect lighting for architectural, stage or nightclub applications. This product can also be

installed for use in signage and advertising using the dynamic functions available with

DMX512 control. Direct input of DMX512 signal allows the units to be controlled from any

DMX512 controller. This product can be operated as a single unit or in multiple units for

large applications.

The specially developed controller that allows the product to be controlled independent of

the DMX512 controllerenables the userto create andedit a widerange of customprograms.

All programs can be touch-button displayed or scheduled to START and END at scheduled

times. When programs have been created or edited in the controller, it is also possible to

trigger these programs using the DMXIN function when connected to a DMX512 controller.

1.2 PRODUCT FEATURES

LED FIXTURE

* RGB Dimmer 0-100%

* Strobe

* Automatic programs

* IP65 protection rating

* LED display

* Display control 'lock-out'

* DirectDMX512 input

* Independant IDaddress

* Lightweight aluminium casing

* RGB Dimmer 0-100%

* Strobe

* Clock & Timer

* Automaticprograms (wash &effect)

* Custom programs

* Program Schedule

* LCD display

* Display control 'lock-out'

* DirectDMX512 input

* Lightweight plastic casing

PiX CONTROLL ER

1 PRODUCT(GENERAL) 2

2007.03.10

1.3 TECHNICAL SPECIFICATIONS

CONTR OLLER

LED MODULE

Dimensions

LED MODULE:

Voltage

Rated Power

IP65 protection rating

36pcs (12 xRED / 12x GREEN / 12 x BLUE)

Weight

LED/Unit

Output/LED

LED Beam Angle

Cooling

15 (30 Optional)

Direct air convection

235 x 165x 300mm

4Kg

90~250V...50/60Hz

65W

Dimensions

Weight

CONTROLLER:

Voltage

Rated Power

IP33 protection rating

180 x 125x 49mm

0.7Kg

1.5W

220~240V, 50/60Hz......100~120V, 50/60Hz

1 PRODUCT(GENERAL) 3

2007.03.10

235mm

165mm

Environment Temperature

-20 ~40

1.4 PHOTOMETRIC DATA

PHOTOMETRIC DATA

WHITE

2(0.52) 4(1.05) 6(1.57) 8(2.10)

10Distance(m)

(2.60Diameter(m))

2750

700 320 190 145 LUX

RED

2(0.52) 4(1.05) 6(1.57) 8(2.10) 10Distance(m)

(2.60Diameter(m))

1145

290 130 72 50 LUX

GREEN

2(0.52) 4(1.05) 6(1.57) 8(2.10) 10Distance(m)

(2.60Diameter(m))

1763

570 270 158 128 LUX

BLUE

2(0.52) 4(1.05) 6(1.57) 8(2.10) 10Distance(m)

(2.60Diameter(m))

307

98 46 27 22 LUX

1 PRODUCT(GENERAL) 4

2007.03.10

1.5 SAFETY WARNING

IMPORTANT

ALWAYS READ THE USER MANUAL BEFORE OPERATION.

PLEASE CONFIRM THATTHE POWER SUPPLYSTATED ON THE

PRODUCT IS THE SAME AS THEMAINS POWER SUPPLYIN YOUR

AREA.

This product must be installed by a qualified professional.

Always operate the equipment as described in the user manual.

A minimum distance of 0.5m must be maintained between the equipment and

combustible surface.

The product must always be placed in a well ventilated area.

Always make sure thatthe equipment is installed securely.

DO NOT stand close to the equipment and stare directly into the LED light

source.

Always disconnect the power supply before attempting and maintenance.

Always make sure that the supporting structure is solid and can support the

combined weight ofthe products.

The earth wire must always be connected tothe ground.

Do not touchthe power cablesif your handsare wet.

ATTENTION

This product leftthe place ofmanufacture in perfect condition. In order to

maintain this condition and for safe operation, the user must always follow the

instructions and safety warnings described in this user manual.

Avoid shaking or strong impactsto any partof the equipment.

Make sure thatal parts ofthe equipment arekept clean andfree of dust.

Always make sure that the power connections areconnected correct and

secure.

If there is any malfunction of the equipment, contact your distributor

immediately.

When transferring the product, it is advisable to use theoriginal packaging in

which the productleft the factory.

Shields, lenses or ultraviolet screens shallbe changed ifthey have become

damaged tosuch an extent that their effectivenessis impaired.

The lamp (LED) shall be changed if ithas become damaged or thermally

deformed.

1 PRODUCT(GENERAL) 5

2007.03.10

2.1 MOUNTING

2.2 POWER CONNECTIONS

2.3 SETTING UP WITH A DMX512 CONTROLLER

2.3-1 DMX512 ADDRESSING WITHOUTID ADDRESSING

2.3-2 DMX512 ADDRESSING WITH ID ADDRESS

2.4 SETTING UP WITH THE PiX CONTROLLER

2.4-1 SINGLE ROW APPLICATION

2.4-2 STANDARD BLOCK APPLICATION

2.4-3 REPEAT ROW BLOCK APPLICATION

2.5 OPERATION: DMX512 Vs PiX CONTROLLER

INSTALLATION

2007.03.10

2 INSTALLATION

2.1 MOUNTING

HANGING

UPRIGHT

The LED PAR can be mounted in an upright or

sitting position usingthe supporting brackets.

The LED PAR can be mounted in a hanging position using

the supporting bracket. The bracket should be secured to

the mounting truss or structure using a standard mounting

clamp. Please note that when hanging the unit a safety

cable should also be used.

@ 220V:40 units may be connected in series

@120V: 20units may be connected in series

The LED MODULE can be mounted at any angleand in any

position. It ispossible to furtheradjust the angleof the LED

MODULE using the two adjustment knobslocated on the side of

the fixture.

2.2 POWER CONNECTIONS

2007.03.10

2 INSTALLATION

2.3 SETTING UP WITH A DMX512

CONTROLLER

2.3-1 DMX512 ADDRESSING WITHOUT ID ADDRESSING

The figure above shows a simple DMX512

layout with thestarting address of the first

unit setat 1, with the second set at 10 and

so on... (Note that when used in this way,

the CH8 IDfunction must be inactive (CH8=0))

DMX512

CONTROLLER

Connect the DMX512controller to theunits in series.

Each unit has 9 DMX channels so theDMX Addresses should increase by increments of

9 (e.g. 1,10,19,28...)

The ID addresshas not beenset so therefore when usingthe controller CH8must

be inactive (CH8=0 ).

Each DMX Address may beused as many times as required.

Any DMX address inthe range from 001 to 500 may beused.

2.3-2 DMX512 ADDRESSING WITH ID ADDRESS

Connect the DMX512 controller to the units in series

Each unit has 9 DMX channels so theDMX Addresses should increase by increments of

9 (e.g. 1,10,19,28...)

Each DMX Address may beused as many times as required.

Any DMX address inthe range from 001 to 500 may be used.

Each DMX addressmay carry upto 66 separateID addresses.

ID should be set in the menu on each unit in ascending values

(i.e. 1,2,3...)

ID addressesare accessible from Ch8 on the DMX512 controller.

Example:

2007.03.10

2 INSTALLATION

DMX Addr.1 DMX Addr.10 DMX Addr.19

DMX512

CONTROLLER

Example:

The figure above showsa simple DMX layout

which has usedthree units ateach DMX address.

The three unitshave different ID addresses which

allows the user to collectively control the whole

group ofunits at that DMX address by setting

CH8 to 0, or to control each unit independently by

first selecting the DMX address and then byusing

CH8 to locatethe target IDaddress.

2.4 SETTING UP WITH THE PiX

CONTROLLER

2.4-1 SINGLE ROW APPLICATION

Connect the fixturesto the PIXCONTROLLER in series.

ID Address should be set in the Id menu on each unit in ascending values

(i.e. 1,2,3...Not required for WASH programs).

When using thePIX CONTROLLER with the fixtures there isno need toset the DMX

address.

When usingthe Effect programs it is important to set the Range of fixtures in the

Settings menu of the PIXCONTROLLER.

Example:

In the figure above the PIX controller is connected inseries to 4 units with corresponding

ID addresses from 1to 4. In order to activatethe Effect programs in the PIXCONTROLLER,

the Range must be setto 004 in the Settings menu of the PIX CONTROLLER.

CONTROLLER

MODE SETUP UP DOWN

2007.03.10

2 INSTALLATION

DMX Addr.1

ID Addr.1

DMX Addr.1

ID Addr.2

DMX Addr.1

ID Addr.3

DMX Addr.10

ID Addr.1

DMX Addr.10

ID Addr.2

DMX Addr.10

ID Addr.3

ID Addr.1 ID Addr.2 ID Addr.3 ID Addr.4

Connect the fixtures to the PIX CONTROLLER in series in the direction that is required.

ID Address should be set in the Id menu on each unit in ascendingvalues

(i.e. 1,2,3...Not required for WASH programs).

When usingthe Effect programs it is important to set the Range of fixtures in the

Settings menu of the PiX CONTROLLER.

2.4-2 STANDARD BLOCK APPLICATION

In the figure above the PiX controller is connected in series to 9 units with corresponding

ID addresses from 1to 9. In order to activatethe Effect programs inthe

PIX CONTROLLER, the Range must be setto 009 in the Settings menu of

the PIX CONTROLLER. (Note: it ispossible to create differentkinds of effects by changing

the direction andposition of IDAddresses)

2007.03.10

2 INSTALLATION

Example:

CONTROLLER

MODE SETUP UP DOWN

ID Addr.1 ID Addr.2 ID Addr.3

ID Addr.6ID Addr.5ID Addr.4

ID Addr.7 ID Addr.8 ID Addr.9

In the figure above the PIXcontroller is connected in series to 9 fixtures with each row comprising

of 3 fixtureswith corresponding IDaddresses from 1to 3. Eachrow is repeatedso that theID

addresses appear the same was as the first row. In order to activate the Effect programs in

the PIX CONTROLLER, the Range must be setto 003 in the Settings menu of the

PIX CONTROLLER.

2.4-3 REPEAT ROW BLOCK APPLICATION

Connect the fixturesto the PIX CONTROLLER inseries.

ID Address should be set in the Id menu on eachunit in ascendingorder with

each row repeated (Not required for Wash programs).

When using thePRO-a CONTROLLER withthe fixtures there is noneed to setthe DMX

address.

When usingthe Effect programs it is important to set the Range of fixtures in the

Settings menu of the Pix CONTROLLER.

2007.03.10

2 INSTALLATION

Example:

CONTROLLER

MODE SETUP UP DOWN

ID Addr.1 ID Addr.2 ID Addr.3

ID Addr.3ID Addr.2ID Addr.1

ID Addr.1 ID Addr.2 ID Addr.3

2.5 OPERATION: DMX512 Vs PiX

CONTROLLER

OPERATION WITH ADMX512 CONTROLLER

DMX512 ADDRESS

ID ADDRESS

DMX512 ADDRESS

ID ADDRESS

DMX512 ADDRESS

ID ADDRESS

DMX512 ADDRESS

ID ADDRESS

AVAILABLE

FUNCTIONS

BENEFITS DRAWBACKS

No need toset

up DMX Address

or IDAddress

Must locate

previosly stored

DMX Address

Advanced

WASH &

EFFECT

programming

Basic WASH

programming

Advanced

WASH &

EFFECT

programming

Units are fully controlled

from DMX512 controller

DMX Address

ID address allowsfor

less DMX channels

when programming*

Advanced fixture

mapping

Programming requires

many DMX channels

All ID addresses

must be set

All ID addressesmust

be set

Basic WASH

Programming

Only control ofall

units at thesame time

DMX address not used

Only control ofall units

at the sametime

All ID Addresses

must be set

All ID Addresses

must be set

Play WASH auto

programs, Basic

CUSTOM

programming &

Schedule play

Play WASH auto

programs, Basic

CUSTOM

programming &

Schedule play

No need toset up

DMX Address or

ID Address

Play WASH &

EFFECT auto

programs, Advanced

CUSTOM

programming &

Schedule play

Play WASH &

EFFECT auto

programs, Advanced

CUSTOM

programming &

Schedule play

DMXAddressnotused

Controlspeedand time of

all WASH &

EFFECT programs

Create powerful

CUSTOM programs

Schedule play

Trigger autoprograms with

DMX IN

DMXAddressnotused

Controlspeedand time of

all WASH &

EFFECT programs

Create powerful

CUSTOM programs

Schedule play

Trigger autoprograms with

DMX IN

OPERATION WITH THE PiX CONTROLLER

DMX512 ADDRESS

ID ADDRESS

DMX512 ADDRESS

ID ADDRESS

DMX512 ADDRESS

ID ADDRESS

DMX512 ADDRESS

ID ADDRESS

AVAILABLE

FUNCTIONS

BENEFITS DRAWBACKS

2007.03.10

2 INSTALLATION

3.1 BASIC

3.2 MENU

3.3 ACTIVATING AUTO PROGRAMS

3.4 DMX512 SETTINGS

3.5 ID ADDRESS

3.6 EDITING CUSTOM PROGRAMS

3.7 SPECIAL SETTINGS

3.8 ACTIVATE THE PASSWORD

3.9 RGB CHANNEL MODEL

DISPLAY PANEL OPERATION

2007.03.10

3 DISPLAY PANEL OPERATION

3.1 BASIC

The LED fixtureis mounted witha LCD displayand 4 controlbuttons.

MENU SET UP

DOWN

enter the currently selected menu or confirm the current function value

scroll 'UP' through the menulist or increase the valueof the current function

scroll'DOWN'throughthemenulist ordecrease thevalueof thecurrentfunction

scroll through the mainmenu or return to the main menu

UPSET DOWNMENU

POWER O UTPOWER I N

DMX IN DMX OUT

2007.03.10

3 DISPLAY PANEL OPERATION

3.2 MENU

AUTO AT.01

AT.02

AT.10

PR.C1

PR.C2

PR.C10

dMX

d 001 512

I 001 IO66

R. 0 255

G. 0 255

B. 0 255

S. 0 255

T. 0 255

F. 0 255

Edit

PR.C1

PR.C2

PR.C3

PR.C4

PR.C5

PR.C6

PR.C7

PR.C8

PR.C9

PR.C10

rEd

GrEn

bluE

Strb

TInE

FAdE

SC.01

SC.02

SC.30

SET UPLd

PASS

***

Send

End

REST

PASS

***

rEST

PASS

ARC

RGb

OFF

2007.03.10

3 DISPLAY PANEL OPERATION

3.3 ACTIVATING AUTO PROGRAMS

3.4 DMX512 SETTINGS

AUTO AT.01

AT.02

AT.10

PR.C1

PR.C2

PR.C10

dMX

d 001 512

Auto

Select the target[Auto] program andpress SET

Programs AT.01 to AT.10 are fully pre-programmed and will not be altered

by changes in EdIT mode

Programs PR.C1 to PR.10 are fully pre-programmed and can be edited

in EdIT mode

dMX

Enter the dMX mode to setthe DMXADDRESS.

2007.03.10

3 DISPLAY PANEL OPERATION

I 001 IO66

3.5 ID ADDRESS

3.6 EDITING CUSTOM PROGRAMS

R. 0 255

G. 0 255

B. 0 255

S. 0 255

T. 0 255

F. 0 255

Edit

PR.C1

PR.C2

PR.C3

PR.C4

PR.C5

PR.C6

PR.C7

PR.C8

PR.C9

PR.C10

rEd

GrEn

bluE

Strb

TInE

FAdE

SC.01

SC.02

SC.30

Enter the Id mode to setthe IDADDRESS

EdIT

Enter the EdIT mode to editthe custom programs PR.C1 to PR.10

Each custom program has 30 steps that can be edited

Each step allowsthe creation ofa scene usingRED rED , GREEN GrEn ,

BLUE bLUE , STROBE STrB , TIME TInE & FADE FAdE

2007.03.10

3 DISPLAY PANEL OPERATION

3.7 SPECIAL SETTINGS

3.8 A CTIVATE THE PASSWORD

SET UPLd

PASS

***

Send

End

REST

PASS

***

rEST

PASS

OFF

SET

Select UPLd to upload thecustom programs fromthe current MASTERunit to

the SLAVE units.

In order to activate the upload function thepassword must be entered

Password is thesame as the main accesspassword

When uploading theMASTER and SLAVE units willdisplay YELLOW

If an error occurs whenuploading the MASTERand/or SLAVE units willdisplay RED

On successful uploading of the customprograms the MASTERand SLAVE units

will display GREEN.

In order toreset custom modesto default valuesselect rEST

PASS

Enter the PASS mode to selectwhether the accesspassword is onor off.

In order toenter access passwordit is necessaryto first press SET

Access password is UP + DOWN + UP + DOWN

2007.03.10

3 DISPLAY PANEL OPERATION

3.9 RGB CHANNEL MODEL

ARC

RGb

Enter the RGb mode, the DMX512only receive 3channels' signal, thesequence

is channel 1 RED (0~255), channel 2 GREEN (0~255) , channel 3 BLUE

(0~255).

Page is loading ...

Briteq Led Power Beam BRITEQ Owner's manual

Brand: Briteq

Model: Led Power Beam BRITEQ

Category: Stroboscopes & disco lights

Type: Owner's manual

The fixture features RGB dimming, strobe effects, and automatic programs, all controllable via DMX512 or the included PiX controller.

Download PDF

report

Briteq Led Power Beam BRITEQ Owner's manual

Briteq Led Power Beam BRITEQ Owner's manual

Related papers

Other documents