Alpha XM2-300HP CableUPS Series Installation guide
- Category
- Rack accessories
- Type
- Installation guide
Power Supply
SPI
12V Battery
1. See Fig. 1 for the dimensions of the shelf. Select a location that allows
sufcient clearance on the top, bottom and sides for cabling and
ventilation required for the installation.
2. Locate one stud and drill pilot hole. Install rst user-supplied 5/16" lag
bolt and hang the shelf using keyslot. Mark and drill second hole in a
stud and install second lag bolt. Secure both lag bolts once shelf is
positioned.
3. To install an SPI, use either of the two SPI mounting holes on the top of
the rack. Place the SPI so that the seizure screw is facing up. Tighten the
SPI to 130 in-lbs (14.5 Nm) of torque.
4. Verify the power supply is connected to the rack grounding connection.
The power supply connects to a ground stud
1
in Fig. 1. Follow the
proper stack-up as shown in Fig. 2 to attach the supplied #10-32 nut,
lock washer, at washer, and supplied ground wire.
5. Verify the rack is connected to ground via either of the #10-32 ground
studs
1
in Fig. 1, and a user-supplied ground wire. Follow the proper
stack-up as shown in Fig. 2 to attach the supplied #10-32 nut, lock
washer, at washer, and customer supplied ground wire. Refer to
applicable codes to determine additional grounding requirements.
Wall-Mount Rack (1 Battery) Installation Instructions
20.50"
521mm
1
1
#10-32 ground studs
Fig. 1, Mounting hole layout
Fig. 2, Ground wire stack up
1
For proper operation of the Power Supply and Communications
Module, external grounding of the rack is required.
IMPORTANT:
Installation Procedure:
Tools and Materials:
• Two user-supplied 5/16" x 3" (or metric equivalent) lag bolts
• User-supplied grounding wire (of sufcient length for application)
• Drill with 1/4" (or metric equivalent) drill bit
• Ratchet with 1/2" and 5/16" (or metric equivalent) sockets
• Level
• 1" Torque Wrench
• Stud nder (optional)
• Tape measure (optional)
For installation and connection, refer to the power supply's technical manual at www.alpha.com.
23.62"
600mm
Install the system in a sheltered, weather-protected location
inaccessible to the general public.
NOTICE:
The installer must verify the wall is capable of supporting the loaded
rack. Direct mounting to a wall stud or equivalent is required.
CAUTION!
12" / 305mm
6"
152mm
15.15" / 385mm
Power Supply
SPI
(2) 12V Battery
1. See Fig. 3 for the dimensions of the shelf. Select a location that allows
sufcient clearance on the top, bottom and sides for cabling and
ventilation required for the installation.
2. Locate one stud and drill a pilot hole. Install the rst user-supplied 5/16"
lag bolt and hang the rack using the keyslot. Mark and drill the second
and third center-line holes in the stud and install the second and third lag
bolts. Tighten all lag bolts once the rack is positioned.
3. To install an SPI, use either of the two SPI mounting holes on the top of
the rack. Place the SPI so that the seizure screw is facing up. Tighten the
SPI to 130 in-lbs (14.5Nm) of torque.
4. Verify the power supply is connected to the rack grounding connection.
The power supply connects to the left ground stud
1
in Fig. 3. Follow
the proper stack-up as shown in Fig. 4 to attach the supplied #10-32 nut,
lock washer, at washer, and supplied ground wire.
5. Verify the rack is connected to ground via either of the #10-32 ground
studs
1
in Fig. 3, and a user-supplied ground wire. Follow the proper
stack-up as shown in Fig. 4 to attach the supplied #10-32 nut, lock
washer, at washer, and customer supplied ground wire. Refer to
applicable codes to determine additional grounding requirements.
Wall-Mount Rack (2 Battery) Installation Instructions
12" / 305mm
6"
152mm
15.15" / 385mm
20.50"
521mm
1
1
#10-32 ground studs
Fig. 3, Mounting hole layout
Fig. 4, Ground wire stack up
1
For proper operation of the Power Supply and Communications
Module, external grounding of the rack is required.
IMPORTANT:
Installation Procedure:
Tools and Materials:
• Three user-supplied 5/16" x 3" (or metric equivalent) lag bolts
• User-supplied grounding wire (of sufcient length for application)
• Drill with 1/4" (or metric equivalent) drill bit
• Ratchet with 1/2" and 5/16" (or metric equivalent) sockets
• Level
• 1" Torque Wrench
• Stud nder (optional)
• Tape measure (optional)
For installation and connection, refer to the power supply's technical manual at www.alpha.com.
23.62"
600mm
Install the system in a sheltered, weather-protected location
inaccessible to the general public.
NOTICE:
The installer must verify the wall is capable of supporting the loaded
rack. Direct mounting to a wall stud or equivalent is required.
CAUTION!
1. See Fig. 5 for the dimensions of the shelf. Select a location that
allows sufcient clearance on the top, bottom and sides for cabling
required for the installation.
2. Using the back of the shelf as a template, cut a piece of 1/2"
plywood and mark and drill pilot holes for the keyslot.
3. Locate one stud and a drill pilot hole. Install the rst user-supplied
5/16" lag bolt and hang the shelf and plywood behind it using the
keyslot. Drill the second hole through the plywood and into the
stud and install the second lag bolt. Drill the top left and right holes
in the plywood though the shelf and install the 3rd and 4th lag
bolts. Tighten all lag bolts once the shelf is positioned.
4. Install the SPI to the SPI bracket and torque to 130 in-lbs (14.5
Nm). Follow the proper stack-up as shown in Fig. 6 and mount
the SPI bracket onto either of the #10-32 studs
2
in Fig. 5, and
tighten the supplied #10-32 nut, lock washer, and at washer.
5. Verify the power supply is connected to the shelf grounding
connection.The power supply connects to the ground stud
1
in
Fig. 5. Follow the proper stack-up as shown in Fig. 7 to attach the
supplied lock washer, #10-32 nut and supplied ground wire.
6. Verify the shelf is grounded via the unused #10-32 ground stud
2
in Fig. 5, and a user-supplied ground wire. Follow the proper
stack up as shown in Fig. 7 to attach the supplied lock washer,
#10-32 nut and customer supplied ground wire. Refer to applicable
codes to determine additional grounding requirements.
Fig. 5, Mounting hole layout and SPI bracket
1
#10-32 ground stud
2
#10-32 SPI mounting bracket / ground stud
Fig. 6, SPI Hardware
stack up
Fig. 7, Ground wire
stack up
3
SPI
Wall-Mount Shelf (Small) Installation Instructions
Install the system in a sheltered, weather-protected location
inaccessible to the general public.
NOTICE:
The installer must verify the wall is capable of supporting the loaded
rack. Direct mounting to a wall stud or equivalent is required.
CAUTION!
Tools and Materials:
• Four user-supplied 5/16" x 3" (or metric equivalent) lag bolts
• User-supplied 1/2" thick sheet of plywood
• User-supplied grounding wire (of sufcient length for application)
• Drill with 1/4" (or metric equivalent) drill bit
• Ratchet with 1/2" and 5/16" (or metric equivalent) sockets
• Level
• 1" Torque Wrench
• Stud nder (optional)
• Tape measure (optional)
For proper operation of the Power Supply and Communications
Module, external grounding of the shelf is required.
IMPORTANT:
Installation Procedure:
Power Supply
SPI
For installation and connection, refer to the power supply's technical manual at www.alpha.com.
3
22
1
10.12"
257mm
8"
203mm
6.09"
155mm
6.94"
176mm
4"
102mm
For more information visit www.alpha.com
United States Bellingham, Washington Tel: 360 647 2360 Fax: 360 671 4936
Canada Burnaby, British Columbia Tel: 604 436 5900 Fax: 604 436 1233
member of
The Group
TM
Alpha Technologies reserves the right to make changes to the products and information contained in this document without notice. Copyright © 2016 Alpha Technologies. All Rights Reserved. Alpha
®
is a registered trademark of
Alpha Technologies. member of The Alpha Group™ is a trademark of Alpha Technologies. 746-221-C0-001 Rev. C (01/2016) To report errors or omissions in this document, send email to T[email protected]
For installation and connection, refer to the power supply's technical manual at www.alpha.com.
1. Refer to Fig 8 for the shelf dimensions. Select a location that
allows sufcient clearance on the top, bottom and sides of the
shelf for cabling required for the installation.
2. Using the back of the shelf as a template, cut a piece of 1/2"
plywood and mark and drill pilot holes for the keyslot.
3. Locate one stud and a drill pilot hole. Install the rst user-supplied
5/16" lag bolt and hang the shelf and plywood behind it using the
keyslot. Drill the second hole through the plywood and into the
stud and install the second lag bolt. Drill the top left and right holes
in the plywood though the shelf and install the 3rd and 4th lag
bolts. Tighten all lag bolts once the shelf is positioned.
4. Install the SPI to the SPI bracket and torque to 130 in-lbs (14.5
Nm). Follow the proper stack-up as shown in Fig. 9 and mount
the SPI bracket onto either of the #10-32 studs
2
in Fig. 8, and
tighten the supplied #10-32 nut, lock washer, and at washer.
5. Verify the power supply is connected to the shelf grounding
connection.The power supply connects to the ground stud
1
in
Fig. 8. Follow the proper stack-up as shown in Fig. 10 to attach
the supplied lock washer, #10-32 nut and supplied ground wire.
6. Verify the shelf is grounded via the unused #10-32 ground stud
2
in Fig. 8, and a user-supplied ground wire. Follow the proper
stack up as shown in Fig. 10 to attach the supplied lock washer,
#10-32 nut and customer supplied ground wire. Refer to applicable
codes to determine additional grounding requirements.
Fig. 8, Mounting hole layout and SPI bracket
1
#10-32 ground stud
2
#10-32 SPI mounting bracket / ground stud
Fig. 9, SPI Hardware
stack up
Fig. 10, Ground wire
stack up
3
SPI
Wall-Mount Shelf (Large) Installation Instructions
Install the system in a sheltered, weather-protected location
inaccessible to the general public.
NOTICE:
The installer must verify the wall is capable of supporting the loaded
rack. Direct mounting to a wall stud or equivalent is required.
CAUTION!
Tools and Materials:
• Four user-supplied 5/16" x 3" (or metric equivalent) lag bolts
• User-supplied 1/2" thick sheet of plywood
• User-supplied grounding wire (of sufcient length for application)
• Drill with 1/4" (or metric equivalent) drill bit
• Ratchet with 1/2" and 5/16" (or metric equivalent) sockets
• Level
• 1" Torque Wrench
• Stud nder (optional)
• Tape measure (optional)
For proper operation of the Power Supply and
Communications Module, external grounding of the shelf is
required.
IMPORTANT:
Installation Procedure:
Power Supply
SPI
3
22
1
12.44"
316mm
10.5"
267mm
6.29"
160mm
6.91"
176mm
4.63"
118mm
-
1
-
2
-
3
-
4
Alpha XM2-300HP CableUPS Series Installation guide
- Category
- Rack accessories
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Alpha Node Power Supply (NPS) Enclosure Installation guide
-
-
Alpha Northern PWE Series Installation guide
-
-
-
-
-
-
-
Other documents
-
Alpha Technologies APX Series Specification
-
Alpha Vision Tech Flexnet MPS48-7M User manual
-
ADTRAN Total Access 1500 Owner's manual
-
Branson 100-214-282 2000Xaod Actuator Owner's manual
-
-
-
Midmark Preva Dental X-Ray System Installation guide
-
-
Nokia Solutions and Networks IHET6BM1 User manual
