AFi MXR2-MM-FX-SC Owner's manual

Brand: AFi

Model: MXR2-MM-FX-SC

Category: Network media converters

Type: Owner's manual

This manual is also suitable for

, American Fibertek, Inc. 0

909

Instruction Manual

MX2-MM-FX-ST

MXR2-MM-FX-ST

MX2-SM-FX-ST

MXR2-SM-FX-ST

Media Converter

Table of Contents

Functional Description

..............................................................................

…3

Installation

....................................................................................................

MX2

Power Source

......................................................................................

MX2

Power Connection

...............................................................................

MX2

Fiber

Data

Connection

.......................................................................

MX2 Copper Data

Connection

...................................................................

MXR2 Power Source

...................................................................................

MXR2 Power Connection

.............................................................................

MXR2 Fiber Data Connections

....................................................................

MXR2 Copper Data Connections

................................................................

MX2 / MXR2

Status LED Indicators

.............................................................

rranty

......................................................................................................

Service Information

......................................................................................

INSTALLATION AND OPERATION INSTRUCTIONS

INTRODUCTION

Thank you for purchasing your American Fibertek MX2 / MXR2

series

media converter. Please take a

few minutes to read these installation instructions in order to obtain the maximum performance from

this product.

FUNCTIONAL DESCRIPTION

The

MX2 / MXR2 s

eries

combines

a single

fiber

Ethernet

port with two copper Ethernet ports. The

MXR2

MX2

, and

MXR2

units

low transmission

speeds of 10 Mb/s or 100 Mb/s on each of the copper

port

The fiber port transmission speed is set at

100 Mb/s. The MX2 / MXR2 series converts the electronic Ethernet input into an optical output using a

1300 nm wavelength source. The MX2 / MXR2 series also converts an optical Ethernet input signal

returning on a separate fiber into an electronic Ethernet output using a

130

0 nm wavelength detector.

The

and

MXR2

units operate on 50 um or 62.5 um multimode fiber with a

maximum distance of 2 Km. The M

-SM-

and

MXR2

-SM-

units operate on 9 um

single

mode fiber with a maximum distance of 20 Km. Refer to the data sheets for detailed performance

specifications.

The

MX2 / MXR2

series

is configured to auto negotiate the copper ports to

either

10Base-T or

100Base

-TX Ethernet data at full or half duplex.

The auto negotiate feature also selects the proper MDI

or MDIX interface. The MX2 / MXR2 series fiber port is set to 100Base-FX and is compatible with

IEEE802.3 100Base

FX standard products.

availability of both a copper and a fiber port allows the

MX2 / MXR2 series product

be used

straight through Ethernet media converter, changing an electronic data signal to a fiber optic data

signal.

This unit is contained in a compact and rugged aluminum housing with internal dc voltage regulation.

The detachable terminal block, RJ45 Ethernet data

connector

, and LED indicators provide for easy

installation and monitoring of data and dc power. The

MX2

eries

is designed for mounting as a

modula

r stand alone unit.

The MXR2

eries is designed for rack mounting

in the MXRC

1 subrack

INSTALLATION

THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD

CONFORM TO THE NATIONAL ELECTRICAL CODE, ANSI/NFPA 70 AND LOCAL CODES.

Mount

MX2 series units

a secure surface using #8 (3mm) hardware in four places. See the

drawing

on the next page for mounting dimensions. Be sure to allow sufficient room for the required minimum

bend radius of the fiber cable used.

MXR2 series units slide into any open slot in the MXRC-1 subrack. Use a small screwdriver to screw

the top and bottom fasteners into place.

DC IN 5V

FX LINK

LINK/ACT2LINK/ACT1

SPD

RXTX

FIBER

PWR

Media Converter MX2-MM-FX-SC

10/100BASE-TX To 100BASE-FX

american fibertek

MX2 Series

MX2 SERIES

POWER SOURCE

THIS PRODUCT SHALL BE POWERED BY A LISTED CLASS 2 POWER SUPPLY ONLY.

MX2 series units require a +5VDC power source for proper operation. The DC input is diode protected.

In the USA and in Canada a 5 Volt DC power supply is supplied with this unit. The negative side of the

power input is directly connected to ground. ANSI/NFPA 70 Class 2 wiring is reco

mmended.

MX2 SERIES POWER CONNECTION

Power is supplied to the MX2 series units via a connection on the right side of the unit (refer to the

drawing

above

MX2 SERIES

FIBER

DATA

CONNECTIONS

The fiber o

ptic connections are made via ST

connectors located o

n the

left

side of the unit. The T

port

of this unit is connected to the

port of the corresponding unit.

MX2 SERIES

COPPER DATA C

ONNECTIONS

The UTP Ethernet input/output connections

are

made via RJ45 plugs on the

left

side of the unit. A

maximum CAT

5 wire length of

00 meters

is permitted

DC IN 5V

SPD

PWR

SPD

FX LINK

FIBER

Media Converter MXR2-MM-FX-SC

10/100BASE-TX To 100BASE-FX

american fibertek

MXR2 Series

MXR

2 SERIES POWER SOURCE

Power to MXR2 series units is supplied by the subrack. Please refer to the MXRC-1 and MXRCPS-

instructions for further details.

MXR

2 SERIES POWER CONNECTION

Power is supplied to the MXR2 series units via a four finger backplane connector. The MXR2 series

units can be inserted into the subrack or removed from the subrack with power applied to the

backplane.

MXR

2 SERIES FIBER

DATA

CONNECTIONS

The fiber optic connections are made via ST connectors located on the

front

of the unit. The TX port of

this unit is connected to the RX port of the corresponding unit.

MXR

2 SERIES

COPPER DATA C

ONNECTIONS

The UTP Ethernet input/output connections are made via RJ45 plugs on the

fron

t of the unit. A

maximum CAT5 wire length of 100 meters is permitted.

MX2 / MXR2

STATUS INDICATORS

The

MX2 / MXR2

series units

provide the following LED status indicators to aid in troubleshooting:

PWR

A green LED indicator monitors the presence of DC power into the unit

Power

status associated with

this LED is summarized below.

PWR

Indicator

Power

Status

Green

Input Power at Correct Level

Off

Check Input Power

ink

Green

LED indicator monitors the fiber connection and data flow on the fiber p

ort

Fiber

status

associated with this LED is summarized below:

Link Indicator

Fiber Port

Status

Solid

Green

Fiber Connected

Flashing Green

Fiber Port Communicating in 100 Mbps Mode

Off

Fiber Not Connected

Link/ACT1

A Green LED indicator monitors the copper connection and data flow on copper port #1.

Port

status

associated with this LED is summarized below:

Link/ACT1

Indicator:

Port 1 Status:

Solid Green

Port 1 Connected

Flashing Green

Port 1 Communicating

Off

No Data Flow

SPD1

A bi-

colored

LED indicator monitors the speed of the data flow on RJ45 copper port #1. Data status

associated with this LED is summarized below:

SPD1 Indicator:

Port 1 Status:

Green

Port

Connected and in 10

Mbps Mode

Amber

Port

Connected and in 10 Mbps Mode

No Data Flow

Link/ACT2

A Green LED indicator monitors the copper connection and data flow on copper port #2. Port status

associated with this LED is summarized below:

Link/ACT

Indicator:

Port 2 Status:

Solid Green

Port 2 Connected

Flashing Green

ort 2 Communicating

Off

No Data Flow

SPD2

A bi-colored LED indicator monitors the speed of the data flow on RJ45 copper port #2. Data status

associated with this LED is summarized below:

SPD

Indicator:

Port 2 Status:

Green

Port 2 Connected and in 10

Mbps Mode

Amber

Port 2 Connected and in 10 Mbps Mode

Off

No Data Flow

WARRANTY INFORMATION

American Fibertek, Inc warrants that at the time of delivery and for a period of five years thereafter

the

products delivered will be free of defects in materials and workmanship. Defective products will be

repaired or replaced at the exclusive option of American Fibertek. A Return Material Authorization

(RMA) number is required to send the products back in case of return. All returns must be ship

ped

prepaid. This warranty is void if the products have been tampered with. This warranty shall be

construed in accordance with New Jersey law and the courts of New Jersey shall have exclusive

jurisdiction over this contract. EXCEPT FOR THE FOREGOING WARRANTY, THERE IS NO

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR

OTHERWISE, EXPRESSED OR IMPLIED, WHICH EXTENDS BEYOND THE WARRANTY SET

FORTH IN THIS AGREEMENT. In any event, American Fibertek will not be responsible or liable for

contin

gent, consequential, or incidental damages. No agreement or understanding, expressed or

implied, except as set forth in this warranty, will be binding upon American Fibertek unless in writing,

signed by a duly authorized officer of American Fibertek.

RVICE INFORMATION

There are no user serviceable parts inside the unit.

In the event that service is required to this unit, please direct all inquiries to:

American Fibertek, Inc.

Phone: (877) 234

7200

120 Belmont Drive

Phone: (732) 302

0660

Somerset, NJ 0

8873

FAX (732) 302

0667

E-

mail:

[email protected]

AFi MXR2-MM-FX-SC Owner's manual

Brand: AFi

Model: MXR2-MM-FX-SC

Category: Network media converters

Type: Owner's manual

This manual is also suitable for

Download PDF

report

AFi MXR2-MM-FX-SC Owner's manual

This manual is also suitable for

AFi MXR2-MM-FX-SC Owner's manual

Related papers

Other documents