Cornelius P/N 629083202 User manual

Brand
Cornelius
Model
P/N 629083202
Category
Ice cube makers
Type
User manual

This manual is also suitable for

Cornelius P/N 629083202 is a "K" style lid kit for ice makers. It is compatible with Manitowoc Q320/420 ice makers and has a width of 22 inches. The kit includes a gray cover, a black cover, an ice maker lid assembly, brackets, screws, an RTV sealant, a label, installation instructions, acorn nuts, sealing washers, a baffle, and nylon washers. The kit allows you to seal the ice maker to the top of the dispenser and install the mounting brackets. It also includes an installation instruction to help you complete the installation process.

Cornelius P/N 629083202 is a "K" style lid kit for ice makers. It is compatible with Manitowoc Q320/420 ice makers and has a width of 22 inches. The kit includes a gray cover, a black cover, an ice maker lid assembly, brackets, screws, an RTV sealant, a label, installation instructions, acorn nuts, sealing washers, a baffle, and nylon washers. The kit allows you to seal the ice maker to the top of the dispenser and install the mounting brackets. It also includes an installation instruction to help you complete the installation process.

1
620909401
March 1998
R
e
v
B
Revised: September 8, 1998
IMI CORNELIUS INC g One Cornelius Place g Anoka, MN 55303-6234
Telephone (800) 238-3600 Facsimile (612) 422-3246
ED150 “K” STYLE LID KITS,
P/N 629083204 AND 629083202
These “K” style kits apply to the following ice maker:
Ice Maker Width
Manitowoc Q320/420 22I
Table 1. Loose-Shipped Parts
Item
No. Part No. Name Qty.
1
52994 Cover, Gray (629083202) 1
1
52934 Cover, Black (629083204)
2 620027505 DF150 Ice Maker Lid Assembly 1
3 620027306 Bracket 2
4 70217 #8 Screw 6
5 50904 RTV 1
6 90221 Label 1
7 620909401 Installation Instruction 1
8 620701902 Acorn Nut, 8--32 Nylon 2
9 620701901 Sealing Washer 2
10 620037007 Baffle, Ice DF/ED150 1
11 621701903 #8 Nylon Washer 2
1. Unpack kit.
2. Insert a baffle assembly into the adapter lid.
3. Place (2) sealing washers (item 9) over studs and (2) flat washers (item11), then fasten in place with (2)
plastic acorn nuts (item 8).
4. Set ice maker lid on the top of the dispenser.
5. Using the slotted holes in the lid as a template, drill four (4) 9/64I diameter holes at the bottom of the slots
(see detail A). Use extreme care not to drill into the hopper. Fasten the lid to the dispenser with four (4) #8
sheet metal screws, two on each side.
6. Seal the ice maker to the top of the dispenser as follows:
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so
that the ice maker will set on the RTV.
2
620909401
B. Set the ice maker onto the lid and position it as required.
C. Wipe away the excess RTV.
7. Remove the two rear screws (only) installed in step 5. Use those screws to install the mounting brackets
(item3). Drill 9/64I diameter holes into the ice maker cabinet using the bracket as a template. Use extreme
care not to drill into any ice maker components (condenser, tubing, etc.). Secure the brackets using the
screws provided
8. Follow the ice maker manufacturers instruction to complete the installation of the ice maker including the
bin thermostat if so equipped or required.
9. If the plastice acorn nuts interfere with the positioning of the plastic manual fill cover, it may be necessary
to make small notches in the back flange of the cover to clear the acorn nuts.
NOTE: Bin Thermostat must not interfere with the agitator rotation.
3
620909401
March 1998
R
e
v
B
Revised: September 8, 1998
ICEMAKER
DETAIL ”A”
DETAIL ”A”
ENLARGED
SEAL ICEMAKER TO
ITEM 2 WITH RTV
3
3
4
4
2
6
DRILL 9/64” (.140” )DIA.
HOLES USING BOTTOM
OF SLOTTED HOLES AS A
TEMPLATE
1
FIGURE 1. DISPENSER ASSEMBLY
4
620909401
VIEW Z--Z
LINER OF LID
2 PLCS.
4 PLCS.
8
9
10
11
2 PLCS.
FIGURE 2. ED150 KIT
5
620909401
March 1998
R
e
v
B
Revised: September 8, 1998
8
9
10
11
VIEW Z--Z
FIGURE 3. ED150 KIT
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Cornelius P/N 629083202 User manual

Brand
Cornelius
Model
P/N 629083202
Category
Ice cube makers
Type
User manual
This manual is also suitable for

Cornelius P/N 629083202 is a "K" style lid kit for ice makers. It is compatible with Manitowoc Q320/420 ice makers and has a width of 22 inches. The kit includes a gray cover, a black cover, an ice maker lid assembly, brackets, screws, an RTV sealant, a label, installation instructions, acorn nuts, sealing washers, a baffle, and nylon washers. The kit allows you to seal the ice maker to the top of the dispenser and install the mounting brackets. It also includes an installation instruction to help you complete the installation process.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents