Sony ICF-C05iPBLK Operating instructions

Brand: Sony

Model: ICF-C05iPBLK

Category: Alarm clocks

Type: Operating instructions

Owner’s Record

e model number and the serial number are located on

the bottom.

Record the serial number in the space provided below.

Refer to them whenever you call upon your Sony dealer

regarding this product.

Model No. ICF-C05iP

Serial No. ________________________________

WARNING

DO NOT INGEST BATTERY, CHEMICAL

BURN HAZARD

is product contains a coin/button cell battery. If the

coin/button cell battery is swallowed, it can cause severe

internal burns in just 2 hours and can lead to death.

Keep new and used batteries away from children. If the

battery compartment does not close securely, stop using

the product and keep it away from children.

If you think batteries might have been swallowed or

placed inside any part of the body, seek immediate

medical attention.

is graphical symbol is located on the bottom of the

unit.

For customers who purchased this product in the

USA

Please register this product on line at

http://www.sony.com/productregistration.

Proper registration will enable us to send you

periodic updates about new products, services, and

other important announcements. Registering your

product will also allow us to contact you in the

unlikely event that the product needs adjustment

or modication. ank you.

WARNING

To reduce the risk of fire or electric shock, do

not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place lighted

candles on the apparatus.

To reduce the risk of fire or electric shock, do not

expose this apparatus to dripping or splashing,

and do not place objects filled with liquids, such

as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug of AC power adaptor is used to

disconnect the AC power adaptor from the mains,

connect it to an easily accessible AC outlet.

Should you notice an abnormality in it,

disconnect it from the AC outlet immediately.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses and

can radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/

TV technician for help.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the manufacturer’s

instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized

plug has two blades with one wider than the

other. A grounding type plug has two blades

and a third grounding prong. The wide blade

or the third prong are provided for your safety.

If the provided plug does not fit into your

outlet, consult an electrician for replacement

of the obsolete outlet.

10) Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit

from the apparatus.

11) Only use attachments/accessories specified by

the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms

or when unused for long periods of time.

14) Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way, such

as power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

For the state of california, USA only

Perchlorate Material –special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate

Perchlorate Material: Lithium battery contains

perchlorate

Features



Wake or sleep to iPod/Radio



FM digital synthesized tuner



20 Station Presets (20 FM)



Brightness Control (High/Mid/Low/Off)



Extendable Snooze system from 10 to 60 min



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the AC power cord (mains lead),

pull it out by the plug, not the cord.



The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from the

unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive dust,

mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit on

a surface (a rug, a blanket, etc.) or near

materials (a curtain) which might block the

ventilation holes.



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth dampened

with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm. Furthermore,

immediately disconnect the AC power cord

from the radio.

NOTES ON LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

If you have any questions or problems concerning

your unit, please consult your nearest Sony dealer.

This symbol is intended to alert

the user to the presence of

important operating and

maintenance (servicing)

instructions in the literature

accompanying the appliance

The Caution Marking is on the bottom of the

unit.

Troubleshooting

Should any problem persist after you have made

the following checks, consult your nearest Sony

dealer.

The clock flashes “AM 12:00” due to a power

interruption.



Check the battery indicator. If the battery

indicator is “



,” replace the battery.

Remove the old battery and install a new one.

The radio, iPod or buzzer alarm does not

sound at the preset alarm time.



Check that alarm is properly displayed.

The radio or alarm of iPod is activated but no

sound comes on at the preset alarm time.



Check the alarm volume setting.

There is no sound from the iPod.



Make sure the iPod is securely connected.



Adjust the VOLUME +.

The iPod cannot be operated with this unit.



Make sure the iPod is securely connected.

The iPod cannot be charged.



Make sure the iPod is securely connected.

When daylight saving time begins, the clock

does not employ the daylight saving time

automatically.



Make sure the clock is set correctly.



Press DST/SUMMER TIME to check that the

“ ” indicator appears.

Specifications

Time display

12-hour system

Section for iPod

DC out: 5 V

MAX: 500 mA

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

General

Speaker

Approx. 5 cm (2 inches) dia, cone type, 16 Ω

Power output

0.8 W (at 10 % harmonic distortion)

Power requirements

DC IN 8V () 1 A

For clock back up: 3V DC, one CR2032 battery

Dimensions

Approx. 134.0 mm × 64.0 mm × 124.5 mm (w/h/d)

inches × 2

inches × 5 inches) not

including projecting parts and controls

Mass

Approx. 410 g (14.5 oz) including power supply

unit

Supplied accessories

AC Power adaptor (1)

Universal Dock Adaptor for iPhone (1)

Universal Dock Adapter for iPhone 3GS &

iPhone 3G (1)

Universal Dock Adapter for iPhone 4S &

iPhone 4 (1)

Design and specifications are subject to change

without notice.

4-174-732-17(1)

About the backup

battery

To keep accurate time, this unit contains a

CR2032 battery inside of the unit as a backup

power source.

The battery keeps the clock operating in the event

of a power interruption.

Knowing when to replace the

battery

When the battery becomes weak, “



” appears in

the display.

If a power interruption occurs while the battery is

weak, the current time and alarm will be erased.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire or

explosion.

Replacing the battery

1 Keep the AC plug connected to the AC

outlet, fully loosen the screw that secures

the battery holder at the bottom of the

unit using a screwdriver, and remove the

battery holder (See fig. -).

2 Replace a new battery in the battery

holder with the  side facing up

(See fig. -).

3 Insert the battery holder back into the

unit and secure it with the screw

(See fig. -).

4 Press iPod & iPhone , SNOOZE/

BRIGHTNESS or FM to turn “



” off in

the display.

Note

When you replace the battery, do not disconnect

the AC power adaptor from the unit. Otherwise,

current time, alarm and station presets will be

erased.









CR2032

Compatible iPod/iPhone

models

Compatible iPod/iPhone models are as follows.

Update your iPod/iPhone to use the latest

software before you use it.

iPod touch (4th generation)

iPod touch (3rd generation)

iPod touch (2nd generation)

iPod touch (1st generation)

iPod nano (6th generation)

iPod nano (5th generation)

iPod nano (4th generation)

iPod nano (3rd generation)

iPod nano (2nd generation)

iPod nano (1st generation)

iPod with video

iPod with color display

iPod with click wheel

iPod classic

iPod mini

iPhone 4S

iPhone 4

iPhone 3GS

iPhone 3G

iPhone

Notes



In these Operating Instructions, “iPod” is used

as a general reference to functions of iPod on an

iPod or iPhone, unless otherwise specified by

the text or illustrations.



The connector of the unit is for sole use with an

iPod/iPhone.



Sony cannot accept responsibility in the event

that data recorded to an iPod is lost or damaged

when using an iPod connected to this unit.

Using House Current

(See fig. )

Use only the AC power adaptor supplied. Do not

use any other AC power adaptor. It may cause a

malfunction.

On the AC power adaptor



Use the supplied AC power adaptor only. The

polarity of the plugs of other manufacturers

may be different. Failure to use the supplied AC

power adaptor may cause the unit to

malfunction.



Do not touch the AC power adaptor with wet

hands.



Connect the AC power adaptor to an easily

accessible AC outlet.

Should you notice an abnormality in the AC

power adaptor, disconnect it from the AC outlet

immediately.



AC power adaptor

(supplied)

DC IN 8V

Clock Radio

ICF-C05iP

Operating Instructions

Dream Machine is a trademark of Sony Corporation.

No Power No Problem is a trademark of Sony Corporation.

Setting the clock

1 Plug in the unit.

2 Press and hold CLOCK until the hour

flashes in the display.

The hour starts to flash in the display.

3 Press ALARM/CLOCK + or – repeatedly

to set the hour.

4 Press CLOCK.

5 Repeat steps 3 and 4 to set the minute,

and then press CLOCK.

The seconds start incrementing from zero.

Notes



If you do not press any button for about 1

minute while setting the clock, the clock setting

will be canceled.



When pressing any of the rear buttons, hold the

unit firmly to prevent slippage.

To change the display to the daylight

saving time (summer time) indication

Change the daylight saving time (summer time)

adjustment setting according to the following

procedures.

Press DST/SUMMER TIME.

“ ” appears in the display and the time indication

changes to the daylight saving time (summer

time).

To deactivate the daylight saving time (summer

time) adjustment, press DST/SUMMER TIME

again. “ ” disappears.

Setting the brightness

of the display

Four levels of brightness are available by pressing

SNOOZE/BRIGHTNESS.

Playing the radio

There are two ways to tune.

To switch between the two tuning methods

(manual tuning or preset), press TUNE MODE/

ENTER MEMORY.

Auto preset

You can preset 20 stations for FM.

1 Press FM to turn on the radio.

2 Press and hold FM until “AP” appears in

the display.

3 Press TUNE MODE/ENTER MEMORY.

The unit automatically presets the available

channels in order.

If a station cannot be preset

automatically

You need to preset a station with a weak signal

manually.

1 Follow steps 1 and 2 in “Manual tuning

mode” to tune the frequency you wish to

preset.

2 Press and hold TUNE MODE/ENTER

MEMORY for preset number until the

flashes.

3 Press TUNE/PRESET  or  to

select the preset number, then press

TUNE MODE/ENTER MEMORY.

The frequency is stored with the selected

preset number.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 2 for FM.



The display shows the frequency for about 10

seconds, and then returns to the current time.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station will

be replaced.

Preset tuning mode

1 Press FM to turn on the radio.

Check that the preset mode is selected.

2 Press TUNE/PRESET  or  to

select the desired preset number.

3 Adjust the volume using

VOLUME + or –.

Manual tuning mode

1 Press FM to turn on the radio.

Check that the manual tuning mode is

selected.

2 Press TUNE/PRESET  or  to

tune in to a desired frequency.

3 Adjust the volume using

VOLUME + or –.

Tuning in to a station

The unit automatically scan FM stations.

1 Press FM to turn on the radio.

Check that the manual tuning mode is

selected.

2 Press and hold TUNE/PRESET  or

.

 : scans upward through the frequency

bands.

 : scans downwards through the

frequency bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3 Adjust the volume using

VOLUME + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to increase

reception sensitivity.

Notes on radio reception



Keep digital music players or mobile phones

away from the FM antenna, as this may lead to

reception interference.



When you are listening to the radio with an

iPhone connected to the unit, interference with

radio reception may occur.



When you are listening to the radio while

charging an iPod, interference with radio

reception may occur.



Do not place the FM antenna close to the AC

power adaptor as noise may result.

Playing an iPod

You can enjoy audio from iPod by connecting to

this unit. To use an iPod, refer to the user’s guide

of your iPod.

If you are using an iPhone 4S, iPhone 4, iPhone

3GS, iPhone 3G or iPhone, attach the supplied

universal dock adapter for iPhone 4S, iPhone 4,

iPhone 3GS, iPhone 3G or iPhone before

connecting.

The adapter number, ,  or , is shown on

the bottom-rear of the supplied universal dock

adapters.  is for the iPhone,  is for the iPhone

3GS & iPhone 3G and  is for the iPhone 4S &

iPhone 4. Check the adapter number before use.





Universal dock adaptor



Notes



When inserting an iPod into the unit, be sure to

use the universal dock adaptor supplied with

your iPod or commercially available from

Apple Inc.



The connector of the unit is exclusively for use

with an iPod.



Sony cannot accept responsibility in the event

that data recorded on an iPod is lost or

damaged when using an iPod connected to this

unit.



For details of environmental conditions for

operating your iPod, check the website of Apple

Inc.

1 Attach the adaptor for your iPod/iPhone.

2 Insert your iPod/iPhone into the

connector of the unit.

3 Press iPod & iPhone .

The iPod begins to play automatically.

You can operate the connected iPod by this

unit or the buttons on iPod.

4 Adjust the volume using VOLUME + or

–.

To Press

Turn off the iPod

OFF, or press and

hold iPod &

iPhone 

Pause playback

iPod & iPhone



To resume play,

press it again.

Go to the next track



Go back to the previous

track

*

Locate a point while

listening to the sound

 (forward) or

 (backward)

while playing and

hold it until you

find the point.

Locate a point while

observing the display

 (forward) or

 (backward)

in pause and hold

it until you find

the point.

* During playback, this operation goes back to

the beginning of the current track. To go back

to the previous track, press twice.

Notes



When placing or removing the iPod, hold the

iPod at the same angle as that of the connector

on this unit, and do not twist or bend the iPod

as connector damage may result.



Do not carry the unit with an iPod set on the

connector. Doing so may cause a malfunction.



When placing or removing the iPod, hold the

iPod firmly so as not to topple the unit.



Before disconnecting the iPod, pause playback.

To use the unit as a battery charger

You can use the unit as a battery charger.

Charging begins when the iPod is connected to

the unit.

Charging status appears in the display of iPod. For

details, see the user’s guide of your iPod.

On copyrights

iPhone, iPod, iPod classic, iPod nano, and iPod

touch are trademarks of Apple Inc., registered in

the U.S. and other countries.

“Made for iPod,” and “Made for iPhone” mean

that an electronic accessory has been designed to

connect specifically to iPod or iPhone,

respectively, and has been certified by the

developer to meet Apple performance standards.

Apple is not responsible for the operation of this

device or its compliance with safety and

regulatory standards. Please note that the use of

this accessory with iPod or iPhone may affect

wireless performance.

Setting the alarm

This clock radio is equipped with 3 alarm

modes—iPod, radio and buzzer. Before setting the

alarm, make sure to set the clock (see “Setting the

clock”).

To set the alarm

1 Press and hold ALARM SET.

“WAKE-UP” appears, and the hour flashes in

the display.

2 Press ALARM/CLOCK + or – repeatedly

until the desired hour appears.

To cycle the hour rapidly, press and hold

ALARM/CLOCK + or –.

3 Press ALARM ON/OFF.

The minute flashes.

4 Repeat step 2 to set the minute.

5 Press ALARM ON/OFF.

The alarm mode setting is entered.

6 Press ALARM/CLOCK + or – repeatedly

until the desired alarm mode flashes.

You can choose one of 3 settings: “iPod”, “FM”

or “BUZZER.” Set the alarm mode as follows:

– iPod: see “ Setting the alarm for iPod.”

– FM: see “ Setting the radio alarm.”

– BUZZER: see “ Setting the buzzer alarm.”

 Setting the alarm for iPod

1 Perform steps 1 to 6 in “To set the

alarm.”

2 Press ALARM ON/OFF to select alarm

mode for “iPod”.

“VOL” appears in the display.

3 Press ALARM/CLOCK + or – to adjust

the volume.

4 Press ALARM ON/OFF.

The setting is entered.

5 If “ALARM” does not appear in the

display, press ALARM ON/OFF again.

The iPod will sound at the set time.

When using an iPod touch/iPhone



To wake up to music stored in an iPod touch/

iPhone, connect the iPod touch/iPhone to the

unit first, follow the steps above to set alarm

time, and then select the music function.



Even if the alarm setting for iPod is complete, if

you turn the power of iPod touch/iPhone off

before inserting the iPod touch/iPhone into the

unit, the alarm for iPod will not work.

 Setting the radio alarm

1 Perform steps 1 to 6 in “To set the

alarm.”

2 Press ALARM ON/OFF to select “FM”

alarm mode.

“FM”, “PRESET” number or “– –” flashes.

“– –” is the last station received.

3 Press ALARM/CLOCK + or – to select

the desired preset number or “– –”.

4 Press ALARM ON/OFF.

“VOL” appears in the display.

5 Press ALARM/CLOCK + or – to adjust

the volume.

6 Press ALARM ON/OFF.

7 If “ALARM” does not appear in the

display, press ALARM ON/OFF again.

The radio will turn on at the set time.

 Setting the buzzer alarm

1 Perform steps 1 to 6 in “To set the

alarm.”

2 Press ALARM ON/OFF to select

“BUZZER” alarm mode.

The setting is entered.

3 If “ALARM” does not appear in the

display, press ALARM ON/OFF again.

The buzzer will sound at the set time.

Note

The volume cannot be set for the buzzer alarm.

To confirm an alarm time setting

Turn off the “ALARM” indicator in the display,

and press the ALARM ON/OFF button once.

To change an alarm setting

Set the alarm again.

To doze for a few more minutes

Press SNOOZE/BRIGHTNESS.

The sound turns off but will automatically come

on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE/BRIGHTNESS repeatedly within

4 seconds.

The maximum length of the snooze time is

60 minutes.

To stop the alarm

Press ALARM RESET OFF to turn off the alarm.

The alarm will sound again at the same time the

next day.

To deactivate the alarm

Press ALARM ON/OFF to turn off the “ALARM”

indicator from the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the battery is totally discharged.

However, certain functions will be affected as

follows:



The backlight will not light up.



If the alarm mode is set to iPod or radio, it will

change to BUZZER automatically.



If a power interruption occurs while the alarm

is sounding, the alarm will stop.



If ALARM RESET OFF is not pressed, the

alarm will sound for about 5 minutes.



If “



” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “



” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep timer

You can fall asleep to the music, etc., using the

built-in sleep timer that turns off the unit

automatically after a preset duration.

1 Press SLEEP while the unit is turned on.

“SLEEP” appears and the sleep time flashes in

the display.

2 Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration (in

minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the duration

setting and released SLEEP, and then the sleep

timer starts.

The unit will play for the duration you set, and

then shut off.

To turn off the unit before the preset

time

Press ALARM RESET OFF.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

The iPod & iPhone  and VOLUME + buttons have a tactile dot.

AC power

adaptor

FM wire antenna

Sony ICF-C05iPBLK Operating instructions

Brand: Sony

Model: ICF-C05iPBLK

Category: Alarm clocks

Type: Operating instructions

Download PDF

report

Sony ICF-C05iPBLK Operating instructions

Sony ICF-C05iPBLK Operating instructions

Related papers

Other documents