IMPORTANT SAFETY INFORMATION
INSTALLER: Please read all instructions before servicing this
equipment. Pay attention to all safety warnings and any other
special notes highlighted in the manual. Safety markings are
used frequently throughout this manual to designate a degree
or level of seriousness and should not be ignored. WARNING
indicates a potentially hazardous situation that if not avoided,
could result in personal injury or death.
WARNING:
ELECTRICAL SHOCK, FIRE OR
EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury or property damage.
Improper servicing could result in dangerous
operation, serious injury, death or property
damage.
• Before servicing, disconnect all electrical
power to the unit.
• When servicing controls, label all wires prior
to disconnecting. Reconnect wires correctly.
• This unit may have more than one power
supply.
• Verify proper operation after servicing.
WARNING:
The safety information listed below must be
followed during the installation, service, and
operation of this it. Unqualified individuals should
not attempt to interpret these instructions or
install this equipment. Failure to follow safety
recommendations could result in possible damage
to the equipment, serious personal injury or death.
• Follow all precautions in the literature, on tags and labels
provided with the equipment. Read and thoroughly understand
the instructions provided with the equipment prior to performing
the installation and operational checkout of the equipment.
• Unless noted otherwise in these instructions, only factory
authorized parts or accessory kits may be used with this
product. Improper installation, service, adjustment, or
maintenance may cause fire, electrical shock or other
hazardous conditions which may result in personal injury or
property damage.
• Use caution when handling this equipment or removing
components. Personal injury can occur from sharp metal
edges present in all sheet metal constructed equipmen
ABOUT THE FREEZESTAT
The Freezestat (FS) included in this kit is a non-adjustable,
sealed, bi-metal switch, set to open at 32° F (+ or-5° F) and
close at 44° F (+ or – 6° F). When installed in a unit, it will
prevent evaporator coil from freezing and limiting the damage
to compressor, due to the following conditions:.
• Lack of airflow.
• Blocked TXV, restrictor or Block liquid line.
• Below normal return air temperatures.
FREEZESTAT INSTALLATION
1. Remove access panels to the evaporator and control panel
as shown in Figure 1 (page 2).
2. Mount the freezestat to liquid line between expansion device
(TXV, Restrictor, EXV) and evaporator coil. See Figure 1
(page 2).
3. Fasten the freezestat to the line using the strap supplied
with this kit. NOTE: Make sure the freezestat has good solid
contact with the liquid line for best performance.
4. Route the wires of the freezestat through the knock out hole
(of the control panel) into control panel compartment.
Electrical Connections
Heat Pump Unit with Defrost Board
Wire the Freezestat in series with High Pressure Switch (HPS)
and then connect to terminal HP2 on Defrost Board. See Figure
2 (page 3).
a. Unplug the high pressure switch wire terminal from terminal
HP2 on defrost board.
b. Connect this terminal to one terminal of the extension wire
supplied with this Kit.
c. Connect other terminal of extension wire to one of the
Freezestat wire terminals.
d. Connect other wire terminal of Freezestat to HP2 terminal
on Defrost Board.
Heat Pump Unit with Demand Defrost Board
Wire the freezestat in series with high pressure switch (HPS)
and then connect to terminal SW on the demand defrost board.
See Figure 3 (page 3).
a. Unplug HPS wire terminal from terminal SW on Defrost
Board
b Connect this terminal to one terminal of the extension wire
supplied with this kit.
c. Connect other terminal of extension wire to one of the
freezestat wire terminals.
d. Connect other wire terminal of Freezestat to SW terminal
on Demand Defrost Board.
Air Conditioner Unit without Defrost Board:
Wire the freezestat in series with the high pressure switch (HPS)
and compressor contactor coil. See Figure 4 (page 3).
a. Unplug HPS wire terminal from one terminal of compressor
contactor coil.
b. Connect it to one terminal of extension wire supplied with
this kit.
c. Connect other terminal of extension wire to one of the
Freezestat wire terminal.
d. Connect another terminal of Freezestat back to compressor
contactor Coil.
5. Check the connections before restoring the power to the unit.
6. Start the unit and make sure it operates normally.
7. Reinstall the evaporator or access corner and the control
panel covers.
Freezestat
INSTALLATION INSTRUCTIONS
2
Figure 1. Freezestat Installation Location
Knockout
Freezestat
and Strap
TXV
Control Panel
Compartment
Liquid
Line
3
Figure 4. Freezestat Hookup for AC without Defrost Board
Compressor
Contactor
24V
COM
High
Pressure
Switch
240V
L2 L1
T2 T1
Transformer
YELLOW
YELLOW / BLACK
YELLOW
YELLOW / BLACK
Y1
W2
E
Y2
O
G
C
R
Extension Wire
Supplied
With Kit
Freezestat
Supplied
With Kit
Low
Pressure
Switch
(Select Models)
Unplug HPS wire from
one terminal of compressor
contactor coil and connect it
to one terminal of extension wire.
FIELD WIRING
FACTORY WIRING
Figure 2. Freezestat Hookup for HP unit with Defrost Board
DEFROST
CONTROL
BOARD
Y1 IN
C
R
O
LP1LP2 HP1HP2
High
Pressure
Switch
Extension Wire
Supplied
With Kit
Fr
eezestat
Supplied
With Kit
Low
Pressure
Switch
FIELD WIRING
FACTORY WIRING
Unplug HPS wire from HP2
terminal on defrost board and
connect to one terminal of extension wire
Figure 3. Freezestat Hookup for HP unit with Demand Defrost Board
M
PRESS
SW
REV
VALV E
DEMAND
DEFROST
BOARD
W2-OUT
High
Pressure
Switch
Low
Pressure
Switch
(Select Models)
Extension Wire
Supplied
With Kit
Freezestat
Supplied
With Kit
Unplug HPS wire
from SW terminal
on defrost board
and connect to one
terminal of extension
wire
FIELD WIRING
FACTORY WIRING
Specifications & illustrations subject to change without notice or incurring obligations (01/19).
O’Fallon, MO, © Nortek Global HVAC LLC 2019. All Rights Reserved.
10228650
(NEW)
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Johnson Controls DMS 600 Series Installation, Operation & Maintenance Manual
-
Johnson Controls Unitary Products SUNLINE 2000 BQ 060 Installation guide
-
York Sunline 2000 Installation guide
-
-
Trane EXWA User manual
-
-
Predator DJ150 User manual
-
Thomas & Betts RZ-NA 441-OMS User manual
-
Daikin DBG Gas Electric/DBC Cooling/DBH Heat Pump User manual
-
