Crosley CAE10MR410A11 Owner's manual

Brand: Crosley

Model: CAE10MR410A11

Type: Owner's manual

ii ¸ Im

ii Pac

! I

This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as

instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that

may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.

The power supply cord with

this air conditioner contains a current

detection device designed to reduce the risk

of fire.

Please refer to the section 'Operation of

Current Device' for details.

tn the event that the power supply cord is Prevent Accidents

damaged, it cannot be repaired. It must be

replaced with a cord from the product To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner,

manufacturer. .follow basic precautions, including the following:

Be sure the electrical service is adequate for the model you have chosen. This information

be found on the serial plate, which is located on the side of the cabinet and behind the

grille.

• :Ifthe air conditioner is to be installed in a window, you will probably want to clean both

sides of the glass first. If the window isa triple-track type with a screen panel included,

remove the screen completely before installation.

not remove any prong from the power cord. . Be sure the air conditioner has been securely and correctly installed according to the

separate installation instructions provided with this manual. Save this manual and the

Grounding type wall installation instructions for possible future use in removing or reinstalling this unit.

receptacle , When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front

and rear coils.

/_1 not, under any ......................................................................................................................................................................................................................................................................................................................................................................................................................................................

circumstances, cut,

remove,

[ _ or bypass the

prong./ ectrica nformat on

The complete electrical rating of your new room air conditioner is stated on the serial plate.

: _ _,_ Refer to the rating when checking the electrical requirements.

j._ • Be sure the a_rcond_honer _sproperly grounded. To mlnmlze shock and fire hazards,

I '_ proper grounding _s_mportant. The power cord _sequipped w_th a three-prong grounding

iJj _ • plug for protection against shock hazards.

Yourconditionermustbeusedproper ygroundedreceptacle fthewall

Power supply cord _ receptacle you intend to use is not adequately grounded or protected by a time delay fuse

with 3-prong grounding _ or circuit breaker, have a qualified electrician install the proper receptacle.

plug and current _ • Do not run air conditioner without outside protective cover in place. This could result in

detection device _ mechanical damage within the air conditioner.

. Do not use an extension cord or an adapter plug.

Avoid fire hazard or electric shock. Do not

use an extension cord or an adaptor plug. Do

DANGER! Avoid Serious Tnjury or Death

This air conditioner contains no user-serviceable parts. Always call an authorized servicer for repairs.

Do not insert or place fingers or objects into the air discharge area in the front of the unit.

Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.

Do not cut or damage the power cord.

[f the power cord is damaged, it should only be replaced by an authorized servicer.

[n the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized

servicer.

Do not operate the air conditioner with wet hands.

Do not pull on the power cord.

= Do not drink any water that is drained from the air conditioner.

CAUTION. I Avoid Injury or damage to the unit or other property

Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make

units run excessively.

Do not climb on or place objects on outdoor part of the unit.

Do not hang objects off the unit.

Do not place containers with liquids on the unit.

Turn off the air conditioner at the power source when it will not be used for an extended period of time.

Periodically check the condition of the unit's installation accessories for any damage.

Do not apply heavy pressure to the radiator fins of the unit.

Operate the unit with air filter in place.

Do not block or cover the intake grille, discharge area and outlet ports.

Ensure that any electrical/electronic equipment is one yard away from the unit.

Do not use or store flammable gases near the unit.

READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.

Unit must be upright for one hour prior to operating.

Operation of Current

Device

Plugin &

pressRESET

The power supply cord contains a current device that senses damage to the power cord. To test

your power supply cord do the following:

1. Plug in the Air Conditioner.

2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will

notice a click as the RESET button pops out.

3. Press the RESET button, Again you will notice a click as the button engages.

4. The power supply cord is now supplying electricity to the unit. (On some products this is also indi-

cated by a light on the plug head).

;;, Do not use this device to turn the unit on or off.

• Always make sure the RESET button is pushed in for correct operation.

• The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,

or it cannot be reset. A new one can be obtained from the product manufacturer,

• If power supply cord is damaged, it CANNOT be repaired, It MUST be replaced by one obtained

from the product manufacturer,

ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!jii;i!ii 3

Packaging Remove all packaging from inside the carton, along with any

inserts placed into the side louvers,

PACKAGING

INSERTS

Normal Sounds

Sound of Rush/n_

At the front of the unit, you may

hear the sound of rushing air

being moved by the fan.

High pitched Chatter

Today's high efficiency compressors

may have a high pitched chatter

during the cooling cycle.

Vibration

Unit may vibrate and make noise

because of poor wall or window

construction or incorrect installation.

Pinqinq or Swishin

Droplets of water hitting condenser

during normal operation may cause

"pinging or swishing" sounds.

Gurgle/Hiss

"Gurgling or hissing" noise may be heard

due to refrigerant passing through

evaporator during normal operation.

Using Air Conditioner

To begin operating the air conditioner, follow these steps:

1. Set the temperature selector to the highest number (coldest or coolest setting).

2. Set the mode control to the highest COOL setting.

(3. Adjust the louvers for comfortable air flow (see Air Directional Louvers).

4. Once the room has cooled, adjust the temperature selector to the setting you

find most comfortable.

Review the "Operating Instructions" section for other settings.

Operating Instructions

TEMPERATURE

min 7

cool OFF coo_

/ \

reed reed

fan c001

fan cool

COOLING

The controls featured in this manual are representaUve of many available

models. Your model may offer slightly different features.

Temperature Selector

This is used to set the desired room temperature when the unit is being

operated in the "COOLMODE':

Toset the desired room temperature, rotate the selectorswitch to the desired

setting. After the set temperature is achieved,the thermostat will automatically

start and stop the compressor in order to maintain the desired set temperature.

Rotate the temperature selector clockwise for higher cool setting. Higher cool

settings will provide lower room temperature.

Rotate the temperature selector counter-clockwise for lower cool settings.

Lower cool settings will provide higher room temperature.

Cool Hode

The desired cool setting is selected by rotating the NODE knob to the appropriate location.

"hi cool" has maximum cooling effect and airflow.

"med cool" has the intermediate cooling effect and airflow.

"1o coot" has minimum cooling effect and airflow.

Note:If your unit is equipped with a vent handle, keep it closed for maximum efficiency.

Fan Hode

Rotate the MODE knob to the left to select your choice of fan speeds for air circulation.

Note:Whenselectinga fanspeed,the compressorwill notrun. Onmodelswith a vent

control,thismodecanbe usedto removestaleair fromthe room,or to drawfreshair

intothe room.Checkthe section'AdditionalThingsYouShouldKnow'.

Please always wait 3 minutes when turning unit off then on again, and when changing from cool to fan and back to

cool. This prevents compressor from overheating & possible circuit breaker tripping.

Failure to follow these instructions may be harmful to your unit.

Operating Instructions

(continued)

(8-WAY)'_

AUGER WHEELS

Air Directional Louvers

Air directional louvers control air flow direction. Your air conditioner has the louver

type described below.

Auger Type

The louvers will allow you to direct the air flow Up or Down and Left or Right

throughout the room as needed. Rotate the Auger Wheels until the desired

Left/Right direction is obtained. Pivot horizontal louvers until the desired

Up/Down direction is obtained.

ADDITIONAL THINGS YOU SHOULD KNOW

Now that you have mastered the operating procedure, here are more features that you should become familiar with.

i i i1,_

I/IF_

1/_t:=:l

Figure 1 (VENT CLOSED)

Fresh Air Vent Control (on some models)

The Fresh Air Vent allows the air conditioner to:

1. Redrculate inside air - Vent Closed (see Fig. 1)

2. Exchange air from the room - Vent Open (see Fig. 2)

rl--

Figure 2 (VENT OPEN)

Care and Cleaning

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug

the unit before cleaning to prevent shock or fire hazards,

Air Filter Cleaning

The air filter should be checked at least once a month to see if cleaning is

necessary. Trapped particles in the filter can build up and cause an accumulation

of frost on the cooling coils.

Push the vent handle to the Vent Closed position(where applicable).

• Open the front panel.

o Grasp the filter by the center and pull up and out.

Wash the filter using liquid dishwashing detergent and warm water. Rinse filter

thoroughly. Gently shake excess water from the filter. Be sure filter is

thoroughly dry before replacing

Or instead of washing, you may vacuum the filter clean.

Cabinet Cleaning

• Be sure to unplug the air conditioner to prevent shock or fire hazard. The

cabinet and front may be dusted with an oil-free cloth or washed with a cloth

dampened in a solution of warm water and mild liquid dishwashing detergent.

Rinse thoroughly and wipe dry.

• Never use harsh cleaners, wax or polish on the cabinet front.

• Be sure to wring excess water from the cloth before wiping around the controls.

Excess water in or around the controls may cause damage to the air conditioner.

• Plug in air conditioner.

Winter Storage

If you plan to store the air conditioner during the winter, remove it carefully from

the window according to the installation instructions. Cover it with plastic or return

it to the original carton.

Do not block air flow inside with blinds, curtains or furniture; or outside with

shrubs, enclosures, or other buildings,

The capacity of the room air conditioner must fit the room size for efficient and

satisfactory operation.

Install the room air conditioner on the shady side of your home. A window that faces

north is best because it is shaded most of the day.

Close the fireplace damper, floor and wall registers so cool air does not escape up

the chimney and into the duct work.

Keep blinds and drapes in other windows closed during the sunniest part of the day.

Clean the air filter as recommended in the section "Care and Cleaning".

Proper insulation and weather stripping in your home will help keep warm air out

and cool air in.

External house shading with trees, plants or awnings will help reduce the air

conditioner's work load.

Operate heat producing appliances such as ranges, washers, dryers and dishwashers

during the coolest part of the day.

Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not

the result of defective workmanship or materials in this appliance.

OCCURRENCE SOLUTION

Air conditioner will not operate. Wall plug disconnected. Push plug firmly into wall outlet

Plug Current Device tripped. Press the RESET button.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Selector Control in OFF position. Turn selector to ON (some models) or the desired FAN or COOL setting.

Unit turned off by moving thermostat to a higher number and then immediately turning back to a colder

number. Wait approximately 3 minutes. Listen for compressor to restart

Unit turned off and then on too quickly. Turn unit off and wait 3 minutes before restarting.

Airfrom unitdoes not feelcold

enough.

Temperature selector set too low. Adjust temperature selector to higher number for cooling.

Turn selector to a higher COOL position.

Temperature selector set too warm. Set temperature selector to colder temperature.

Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above

60°F (16°C).

Temperature sensing tube touching cold coil, located behind air filter. Straighten tube away from coil.

Air conditioner cooling, but

room is too warm =ice forming

on cooling coil behind decorative

front

Outdoor temperature below 60 °F (16 °C). To defrost the coil, set selector to a FAN position. Then, set

thermostat to warmer position.

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set selector to FAN.

Temperature selector set too cold for night-time cooling. To defrost the coil, set selector to a FAN

position. Then, set temperature selector to warmer position.

Air conditioner cooling, but room

is too warm =NO ice forming on

cooling coil behind decorative

front,

Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.

Temperature selector set too warm. Turn temperature selector clockwise to a colder setting.

Air directional louvers positioned improperly. Position louvers for better air distribution.

Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in

front of unit.

Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.

Unit recently turned on in hot room. Allow additional time to remove "stored heat" from walls, ceiling,

floor and furniture.

Airconditionerturnson and off

rapidly.

Dirty air filter - air restricted. Clean air filter.

Outside temperature extremely hot. Set to High Cool to bring air through cooling coils more frequently.

Noise when unit is cooling.

Air movement sound. This is normal. If too loud, turn selector to lower FAN setting.

Sound of fan hitting water-moisture removal system. This is normal when humidity is high. Close doors,

windows and registers.

Window vibration - poor installation. Refer to installation instructions or check with installer.

Water dripping INSIDE when Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to

unit is cooling, installation instructions or check with installer.

Water dripping OUTSIDE when Unit removing large quantity of moisture from humid room. This is normal during excessively humid

unit is cooling, days.

Room too cold, Temperature selector set too high, set to a lower number on temperature dial.

If These Solutions Fail, Call 1-800-944-9044 For Service,

Your appliance is warranted by Crosley. Crostey has authorized Etectrolux and their authorized servicers to perform service under this

warranty. Crosley authorizes no one else to change or add to any of these obligations under this warranty. Any obligations for service

and parts under this warranty must be performed by Electrolux or an authorized Electrotux servicer. For one year from your original

date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in

materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.

From the second to the fifth year from your original purchase date, Electrolux will repair or replace any parts in the Sealed

Refrigeration System (compressor, condenser, evaporator and tubing) proves to be defective in materials or workmanship.

The consumer will be responsible for diagnostic costs and any removal, transportation and reinstatlation costs which are required

because of service, costs for labor, parts and transportation other than with respect to the Sealed Refrigeration System. From the

sixth to the tenth year from your original purchase date, Crosley will replace the compressor with a compressor of the same or

substantially the same quality as the manufacturer's original when this product is installed, operated and maintained according

to instructions attached to or furnished with the product. Pleasesee warranty information packed with product or ask the dealer

for complete warranty details.

This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Product that has been transferred from its original owner to another party or removed outside the USA or

Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased "as-is" are not covered by this warranty.

5. Food loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not

in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,

etc., which are not a part of the appliance when it is shipped from the factory.

10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,

handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip

charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,

cabinets, walls, etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than

genuine Electrohx parts or parts obtained from persons other than authorized service companies; or external

causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR

REPLACEMENT AS PROVIDED HEREIN.CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST

PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLEFOR

CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES

RESULTINGFROMANY BREACHOF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY.SOME

STATESAND PROVINCESDO NOT ALLOW THE EXCLUSIONOR LIMITATION OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SOTHESE LIMITATIONS

OR EXCLUSIONSMAY NOT APPLYTO YOU. THIS WRITTEN WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS.

YOU MAYALSO HAVE OTHER RIGHTS THAT VARY FROM STATETO STATE.

Exclusions

IfYou Need

Service

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period

should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.

Service under this warranty must be obtained by contacting Electrotux at the addresses or phone

numbers below.

This warranty only applies in the USAand Canada. In the USA,your appliance is warranted by Electrohx Major Appliances North

America, a division of Etectrotux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.

Etectrotux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under

this warranty must be performed by Electrohx or an authorized service company. Product features or specifications as described

or illustrated are subject to change without notice.

USA

1.800,944,9044

ElectroluxMajorAppliances

North America

RO. Box 212378

Augusta, GA 30907

Electrolux

Canada

1.800.265.8352

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4

Crosley CAE10MR410A11 Owner's manual

Crosley CAE10MR410A11 Owner's manual

Crosley CAE10MR410A11 Owner's manual

Related papers

Other documents