Mail Chime
page 1
How It Works
When the mailbox door is opened, the Receiver in the house will beep four times and
display a red LED light. After you retrieve your mail, press the reset button to reset.
Model 1200
User's Manual
Remove top case by removing four screws.
Reassemble the case using the 4 screws. Put screws in from top.
Place the battery into the battery holder. Be sure the positive end is
towards the two red wires.
Refer to page 2 and set the dial setting for your type of mailbox.
double faced tape
1.
2.
3.
4.
1
2
3
4
Receiver
Hanna Products Inc.
Reset
Mail Chime
Package Contents
AC adaptor
tm
12 volt, A23 battery
Transmitter
1
2 3
4
Peel the protective cover off the double faced tape on the bottom
of the Transmitter base and attach it to your mailbox door.
5.
Rev. R
battery
battery
knob
negative end
positive end
1. Remove the Transmitter from your mailbox door by removing the four screws.
2. Place the Transmitter down on a surface next to your Receiver so that the
battery is on the top side facing the ceiling.
3. Hold down the reset button on the Receiver until the lights goes out. It will
take about 8-9 seconds before the light goes out.
4. Release the reset button and immediately turn over the Transmitter while the
light is blinking so that the battery is facing down on the table.
5. You should hear 2 quick beeps.
6. Turn your Transmitter over to check if you get 4 beeps before mounting it
to your mailbox.
page 4
Recode Procedure
Shown below is a recode procedure. It is very unlikly that you should ever need to
use this procedure. Your unit will not lose it's code unless someone holds the
reset button on the receiver down for an extended period of time.
Special Instructions for large, heavy metal, and
aluminum mailboxes
1.) Be sure you have a good battery.
2.) Turn the knob on the Transmitter to # 3. The knob is intended to turn hard.
If additional adjustments are needed, please do the following:
1.) Add a piece of wood under the Transmitter.
2.) The wood should be at least 4" X 4" and
3/4 -1 inch thick.
We are controlled by the FCC on the amount of power that can be used and
sometimes it is not enough for large heavy walled mailboxes. Therefore we do
not recommened the Mail Chime for large mailboxes, however if you have one
and are having problems, please do the following.
two red wires
Turn knob to # 3
1
2
3
4
Wood block
Patent No. 7,506,796
This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the
party responsible could void the user's authority to operate this equipment.
FCC ID: RNCMAIL-1200
Hanna Products Inc.
Made in Taiwan
2602 37th Street, Rock Island, IL 61201
Email: hannaproducts@mchsi.com
Phone: 309-788-1982
Designed in USA
Slot Type
Curb Side
1
2 3
4
Wall Mounted
4
3
2
1
Set dial on # 2 - for mailboxes with short tapered lids and flat tops.
Set dial on # 3 - for mailboxes with large tapered lids.
Set dial on # 4 - Mount with arrows
on Transmitter pointing up towards hinge.
Mount with arrows on Transmitter pointing up.
Mount with arrows on Transmitter pointing up.
1
2
3
4
1
2
3
4
Straighten the antenna vertically.
6.
7.
page 3
page 2
Receiver
AC Adaptor
Volume control knob
Plug the AC adaptor into the back of the Receiver and the wall outlet.
8.
Adjust the volume control knob on the back of the Receiver. You may turn
the sound off and use only the LED light if you wish.
Trouble shooting
1. Check if you mounted the Transmitter correctly on your mailbox.
3. Check if the battery is installed correctly.
2. For a curb side mailbox, check if the arrows point towards you when
you open the mailbox door.
Set dial on # 4 - Mount with arrows on Transmitter
pointing up towards the top of the mailbox door.
When you press the reset button down to turn off the red light, do not hold
it down for more tham 1-2 seconds. Just press down and let up.
9.
4. Move the receiver to a different location.
( Arrows should point towards you when you open the door )
2. The Transmitter uses a ball tilt switch so it is normal for you to hear a
rattle when you tip it.
Limited Warranty
During first 30 days, defective units must be returned to retailer for an exchange.
After 30 days, call Hanna Products at 309-788-1982.
6. For problems with large, heavy metal mailboxes, see page 4.
1. The knob on the Transmitter is set on # 4 for curb side mailboxes. Do not
move the knob unless you have a wallmounted or slot type mailbox.
Other tips
Set knob
on # 4
1
2 3
4
Set knob
on # 2 or 3
1
2 3
4
Set knob
on # 4
5. Your mailbox must be level. However, if it leans forward a small amount,
you can often get by, by turning the Transmitter knob to # 3.
-
1
-
2
Sharper Image 1200 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Gaines Manufacturing WM-8 User manual
-
Dakota Alert MBA-1000 mailbox alert Owner's manual
-
Radio Shack 63-1110 - Wireless Mail Guard Owner's manual
-
GE 00007707 User manual
-
-
RCA ViSYS 25450 User manual
-
Motorola Talkabout T900 User manual
-
BMW 735 Owner's Handbook Manual
-
Aastra DT292 User manual
-
Epson Multi-mode Data Controller MFJ-1278B User manual
