Ibiza Light LP64LED-PROMO Owner's manual

©Lotronic – 2014 www.ibizalight.com

L

E

D

P

A

R

6

4

C

A

N

P

R

O

J

E

C

T

E

U

R

A

L

E

D

P

A

R

6

4

L

E

D

P

A

R

6

4

Ref.: LP64 LED-PROMO

INSTRUCTION MANUAL

MANUEL D’UTILISATION

BEDIENUNGSANLEITUNG

HANDLEIDING

MANUAL DE UTILIZARE

NAVODILA ZA UPORABO

MANUAL DE INSTRUÇÕES

©Lotronic – 2014 www.ibizalight.com

L

E

D

P

A

R

6

4

C

A

N

LP64LED-PROMO

INSTRUCTION MANUAL

Thank you for purchasing the LP64LED-PROMO. Every LED PAR-64 has been

well tested and shipped in perfect operating condition.

Safety Instructions

Please read these instructions carefully, they include important information

about the installation, usage and maintenance of this product.

• Please keep this User Guide for future reference. If you sell the unit to

another user, be sure that he also receives this instruction booklet.

• Always make sure that you are connecting to the proper voltage, and that the

line voltage you are connecting to is not higher than that stated on the bottom

of the fixture.

• This product is intended for indoor use only!

• To prevent risk of fire or shock, do not expose fixture to rain or moisture.

Make sure there are no flammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• Always disconnect from power source before servicing or replacing fuse and

be sure to replace with same fuse size and type.

• Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the

fixture at temperatures higher than this.

• In the event of a serious operating problem, stop using the unit immediately.

Never try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized

technical assistance center. Always use the same type of spare parts.

• Don’t connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

GB

©Lotronic – 2014 www.ibizalight.com

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure

that the unit is firmly fixed to avoid vibration and slipping while operating.

Always ensure that the structure to which you are attaching the unit is secure

and is able to support a weight of 10 times of the unit’s weight. Also always use

a safety cable that can hold 12 times of the weight of the unit when installing

the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place

where is out of the touch of people and has no one pass by or under it.

How To Control The Unit

There are three ways to operate the unit:

A. Master/Slave operation

B. Easy sound active and Auto mode

C. Universal DMX controller

A. Master/Slave operation

In master/slave mode you can link as many units together in a days-chain to

perform the built-in pre-programmed lighting shows triggered by music.

For Master/Slave mode please refer to the DMX settings below:

Master unit: when working at Auto-run or Sound Control mode operation

Slave units: DMX start address MUST be set to d001.

(First DIP switch = ON, all

other are OFF)

B. Easy sound active and Auto mode

Set sound active mode:

DIP switch #10 = ON,

Set the speed with the DIP switches # 1-6 = ON, all others are OFF

Set Auto mode:

DIP switch # 9-10 = ON, Set the speed with the DIP switches # 1-6 = ON, all

others are OFF

C. Universal DMX controller

When using a universal DMX controller to control the chain of units, you have

to set DMX address by Dip switches from 1 to 9 to make sure all the units will

receive its DMX signal.

Please refer to the following diagram to know how to address your DMX 512

system in the binary code.

©Lotronic – 2014 www.ibizalight.com

DMX 512 Address Chart:

Dip-

switches

# 1

# 2

# 3

# 4

# 5

# 6

# 7

# 8

# 9

#10

Value

1

2

4

8

16

32

64

128

256

2-light

show

10 bits Dipswitch setting table: 0 for OFF - 1 for ON

Function

Dipswitch setting table

1 2 3 4 5 6 7 8 9 10

Auto Speed 1 Speed 2 Speed 3 Speed 4

Speed 5 0 0 0 1 1

Sound Speed 1 Speed 2 Speed 3 Speed 4

Speed 5 0 0 0 0 1

Red 0 0 0 0 0 1 0 0 1 1

Green

0

1

0

1

Blue

0

1

Red+

Green

0 0 0 0 0 1 1 0 1 1

Red+

Blue

0 0 0 0 0 1 0 1 1 1

Green+

Blue

0 0 0 0 0 0 1 1 1 1

Red+

Green+

Blue

0 0 0 0 0 1 1 1 1 1

DMX512

SET DMX ADDRESS FOR DMX MODE

For example 001. (First DIP switch = ON, all others are OFF)

0

DMX Channel

CH 1

0~255

Blue LED

CH 2

0~255

Green LED

CH 3 0~255 Red LED

CH 4

0~255

Dimming

CH 5

11~255

Strobe (Slow--Fast)

CH 6

11~200 DMX Auto

201~255 DMX Sound

CH 7

0~255

Auto DMX/ Sound DMX Speed (Slow--Fast)

Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be

carried out periodically to optimize light output. Cleaning frequency depends

on the environment in which the fixture operates: damp, smoky or particularly

dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

Clean with soft cloth using normal glass cleaning fluid.

Always dry the parts carefully.

Clean the external optics at least every 20 days. Clean the internal optics at

least every 30/60 days.

Specifications

LED source: ........................................................................... 177pcs x 5mm RGB LEDs

Power consumption: ............................................................................................ 36W

Power supply: ........................................................................... AC220-240V, 50-60Hz

Fuse ........................................................................................................................... 3A

Control mode: ................................ DMX512, sound mode, auto mode, Master-Slave

Control channel: ................................................................................................... 7 CH

Features: .................... color changing, strobe, dimmer 0~100%, speed adjustable

Dimensions: ..................................................................................220 x 220 x 325mm

Weight: ................................................................................................................ 2.8kg

IMPORTANT NOTE: Electric products must not be put into household waste.

Please bring them to a recycling centre. Ask your local authorities or your dealer

about the way to proceed.

Page is loading ...

Ibiza Light LP64LED-PROMO Owner's manual

Ibiza Light LP64LED-PROMO Owner's manual

in other languages

Related papers

Other documents