Real Fyre Evening Fyre See Thru Log G18 Owner's manual

Type
Owner's manual

This manual is also suitable for

1
CAUTION...............WARNING...............IMPORTANT
USE ONLY A PETERSON REAL FYRE G18 BURNER WITH THIS REAL FYRE LOG SET.
Important: Adequate spacing between the
logs is NECESSARY and MUST be
maintained. If carbon build up (sooting)
exists, correct log placement before
sooting becomes worse. If any sooting
occurs outside of the fi rebox (i.e. on
the walls), turn off unit immediately
and contact a qualifi ed professional
service technician.
WARNING: Use ONLY a Peterson Real Fyre
G18 burner with this Real Fyre gas log
set. Failure to do so may result in
property damage or personal injury,
and will void listings, certifi cations,
and invalidate claims made to RHP.
Contact your local Real Fyre dealer if you
need more information.
This instruction contains log set placement for these Real Fyre logs. You must position and maintain the log
layout as shown here to ensure proper operation of the burner system. Incorrect log installation could cause
ame impingement and improper combustion, resulting in soot and/or excessive by-products of combustion.
DO NOT add any additional embers for this installation. Any additional embers will cause unsafe operation.
Use these logs only with a Peterson G18 burner system.
If you experience an accumulation of black carbon (soot) on your logs it is an indication of incomplete
combustion and you must correct the log placement as instructed in this manual. If signifi cant sooting
continues, stop using this gas log set.
Please read these instructions completely and carefully.
This product is only warranted when used as part of a
Robert H. Peterson Co. unvented burner system.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
LOG SET IMPORTANT INFORMATION
L-F2-133REV 0 - 1904081350
EVENING FYRE SERIES LOG PLACEMENT INSTRUCTIONS
EFV-2-24 shown
This instruction shows log set
placement for Evening Fyre (EFV),
Evening Fyre Split (ESV), and Evening
Fyre Charred (ECV).
2
Failure to use a Peterson G18 burner may result in a DANGEROUS
situation and in property damage, personal injury or even death, will void
listings and certifi cations, and will void any insurance coverage by R.H.
Peterson Co. or our insurers.
CAUTION: Burn hazard! Logs will remain hot for some time after use.
If you need to reposition any log to maintain the proper layout,
use heat resistant gloves or allow logs adequate time to cool
before handling.
WARNING: This gas log set is for use with an R.H. Peterson Co. G18
burner (and parts) ONLY.
L-F2-133REV 0 - 1904081350
3
EVENING FYRE SERIES LOG PLACEMENT INSTRUCTIONS (16/18" MODEL)
E(F,S,C)V-16/18
PARTS LIST
1
2
E(F,S,C)VL-2-18B1
E(F,S,C)VL-2-18B2
3
EFVL-2-11TY
4
5
EFVL-2-11TY
EFVL-2-9T
The underside of the bottom logs have cutouts that align over the burner. THE BOTTOM LOGS MUST BE
FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to interlock in place.
EFV-2-16/18 log set shown
1
2
Place the top log (log #3) as shown. The log should lock
in place over the logs below.
Ensure the front logs are snug up against the main burner
bracket.
Logs snug against bracket
3
Align
notches
with
bracket
Cutout
for valve
Cutout for ODS
II
I
III
Place the bottom front logs (log #1and log #2) as shown. Slide them back on the burner, against the main burner bracket.
ENSURE THE LOGS REST FLAT ON THE BURNER, AND THAT THE BURNER BRACKET ALIGNS WITH THE GROOVE
FOUND ON THE BACK OF BOTH LOGS. Both bottom logs are equipped with specifi c indentations for both the valve (log #1)
and the ODS pilot (log #2). Position the logs according to these cutaways shown above.
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
4
6
5
6
CHK-6
CHK-6
CHK-7
CHK-7
1 2
4
EVENING FYRE SERIES LOG PLACEMENT INSTRUCTIONS (16/18" MODEL) (CONT.)
Place both top Y-shapped logs (log #4) as shown. The logs
should lock in place over the logs below.
4
4
IV
VI
After setting the logs into position as described above, ensure each is properly and fi rmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the fl ames will not strike any portion of the logs. Periodically check the positioning of all logs to
ensure proper log placement and stability. If any fl ame is striking the logs, recheck log placement. Adjust
to conform with instructions. There should be no fl ame impingement on the logs.
15 model shown
Side view
Front view
(place all 4 corners)
Place the decorative wood chips in front of the burner. Ensure
the charred ends face inward. For the wood chip in front of the
valve, ensure at least 1" between it and the valve. Repeat for
the opposite side.
CAUTION: Ensure the wood chips by the valve are
placed at least 1" away from the valve to avoid
overheating and damage to the valve. If this
minimum requirement of 1" clearance is
not possible, DO NOT use the wood chip.
CAUTION: THE WOOD CHIPS WILL BE HOT DURING AND
AFTER OPERATION.
5
Final Log Placement
1" (minimum)
V
5
EVENING FYRE SERIES LOG PLACEMENT INSTRUCTIONS (24" MODELS)
E(F,S,C)V-2-24
PARTS LIST
EFV-2-24 log set shown
The underside of the bottom logs have cutouts that align over the burner. THE BOTTOM LOGS MUST BE
FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to interlock in place.
Place the bottom front logs (log #1 and log #2) as shown. Slide them back on the burner, against the main burner bracket.
ENSURE THE LOGS REST FLAT ON THE BURNER, AND THAT THE BURNER BRACKET ALIGNS WITH THE GROOVE
FOUND ON THE BACK OF BOTH LOGS. Both bottom logs are equipped with specifi c indentations for both the valve (log
#1) and the ODS pilot (log #2). Position the logs according to these cutaways shown above.
1
Ensure the front logs are snug up against the main burner
bracket.
Logs snug against bracket
Place both top Y-shapped logs (log #3) as shown. The logs
should lock in place over the logs below.
3
3
Align
notch
with
bracket
Align
notch
with
bracket
Cutout
for valve
Cutout for ODS
II
I
III
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
1
2
E(S,C)VL-2-24B1
EFVL-2-24BF1
E(S,C)VL-2-24B2
EFVL-2-24BF2
3
EFVL-2-10T
4
5
EFVL-2-10T
EFVL-2-12T
4
6
5
6
CHK-6
CHK-6
CHK-7
CHK-7
3
EFVL-2-12T
1
2
2
6
EVENING FYRE SERIES LOG PLACEMENT INSTRUCTIONS (24" MODELS) (CONT.)
Place both top logs (log #4) as shown. The logs should
lock in place over the logs below.
4
4
IV
VI
Final Log Placement
V
After setting the logs into position as described above, ensure each is properly and fi rmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the fl ames will not strike any portion of the logs. Periodically check the positioning of all logs to
ensure proper log placement and stability. If any fl ame is striking the logs, recheck log placement. Adjust
to conform with instructions. There should be no fl ame impingement on the logs.
15 model shown
Side view
Front view
(place all 4 corners)
Place the decorative wood chips in front of the burner. Ensure
the charred ends face inward. For the wood chip in front of the
valve, ensure at least 1" between it and the valve. Repeat for
the opposite side.
CAUTION: Ensure the wood chips by the valve are
placed at least 1" away from the valve to avoid
overheating and damage to the valve. If this
minimum requirement of 1" clearance is
not possible, DO NOT use the wood chip.
CAUTION: THE WOOD CHIPS WILL BE HOT DURING AND
AFTER OPERATION.
5
1" (minimum)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Real Fyre Evening Fyre See Thru Log G18 Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI