SUPER MICRO Computer MNL-H8DI3+-F User manual

Category
Server/workstation motherboards
Type
User manual
®
SUPER
H8DI3+-F
H8DI3+
H8DII+-F
H8DII+
USER’S MANUAL
Revision 1.0c
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0c
Release Date: April 15, 2010
Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2010 by SUPER MICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America
Preface
iii
Preface
About This Manual
This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use of the
H8DI3+/I+(-F) Serverboard. The H8DI3+/I+(-F) serverboard is based on the AMD®
SR5690/SP5100 chipset and supports dual AMD Socket F type processors with up
to 128 GB of DDR2-800/667/533 registered ECC SDRAM. This series includes the
following serverboards and characteristics:
H8DI3+-F H8DI3+ H8DII+-F H8DII+
Embeded IPMI Yes Yes
Onbard SAS Yes Yes
PCI-X Yes Yes Yes Yes
Please refer to the mainboard speci cations pages on our web site for updates on
supported processors (http://www.supermicro.com/aplus/). This product is intended
to be professionally installed.
Manual Organization
Chapter 1 includes a checklist of what should be included in your serverboard
box, describes the features, speci cations and performance of the serverboard and
provides detailed information about the chipset.
Chapter 2 begins with instructions on handling static-sensitive devices. Read this
chapter when installing the processor(s) and memory modules and when installing
the serverboard in a chassis. Also refer to this chapter to connect the hard disk
drives, the various ports, and the power and reset buttons and the system LEDs.
If you encounter any problems, see Chapter 3, which describes troubleshooting
procedures for the video, the memory and the setup con guration stored in CMOS.
For quick reference, a general FAQ (Frequently Asked Questions) section is
provided. Instructions are also included for contacting technical support. In addition,
you can visit our web site for more detailed information.
Chapter 4 includes an introduction to BIOS and provides detailed information on
running the CMOS Setup utility.
Appendix A provides BIOS Error Beep Code Messages.
Appendix B lists BIOS POST Checkpoint Codes.
iv
H8DI3+/I+(-F) Serverboard User’s Manual
H8DI3+/I+(-F) Serverboard User’s Manual
v
Table of Contents
Chapter 1 Introduction
1-1 Overview ............................................................................................................ 1
Checklist ............................................................................................................. 1
1-2 Contacting Supermicro ....................................................................................... 2
1-3 Chipset Overview ............................................................................................. 10
AMD SR5690/SP5100 Processor .................................................................... 10
HyperTransport Technology ............................................................................. 10
1-4 PC Health Monitoring ....................................................................................... 10
1-5 Power Con guration Settings............................................................................11
1-6 Power Supply ................................................................................................... 12
1-7 Super I/O .......................................................................................................... 13
Chapter 2 Installation
2-1 Static-Sensitive Devices ..................................................................................... 1
Precautions ........................................................................................................ 1
Unpacking .......................................................................................................... 1
2-2 Processor and Heatsink Installation................................................................... 2
2-3 Mounting the Serverboard into a Chassis ......................................................... 4
2-4 Installing Memory ............................................................................................... 4
Support ............................................................................................................... 5
Maximum Memory .............................................................................................. 5
2-5 PCI Expansion Cards ......................................................................................... 6
2-6 I/O Port and Control Panel Connections ........................................................... 7
Front Control Panel ............................................................................................ 7
2-7 Connector De nitions ........................................................................................ 8
Power Connectors ........................................................................................ 8
PW_ON Connector ........................................................................................ 8
Reset Connector ........................................................................................... 8
Overheat/Fan Fail LED (OH)......................................................................... 8
NIC2 (LAN2) LED .......................................................................................... 9
NIC1 (LAN1) LED .......................................................................................... 9
HDD LED ....................................................................................................... 9
Power On LED .............................................................................................. 9
NMI Button .................................................................................................... 9
LAN1/2 (Ethernet Ports) ................................................................................ 9
Universal Serial Bus Ports .......................................................................... 10
USB Headers .............................................................................................. 10
Fan Headers ................................................................................................ 10
vi
Table of Contents
Serial Ports .................................................................................................. 10
SGPIO ..........................................................................................................11
SMBus Header .............................................................................................11
Wake-On-LAN ..............................................................................................11
Power I2C .....................................................................................................11
Overheat LED ...............................................................................................11
Chassis Intrusion ........................................................................................ 12
Power LED/Speaker .................................................................................... 12
ATX PS/2 Keyboard and PS/2 Mouse Ports ............................................... 12
I-Button ........................................................................................................ 12
Compact Flash Card PWR Connector ........................................................ 13
2-8 Jumper Settings ............................................................................................... 13
Explanation of Jumpers ................................................................................... 13
CMOS Clear ................................................................................................ 13
I2C to PCI-Express Slot .............................................................................. 14
Watch Dog Enable/Disable ......................................................................... 14
PCI-X Slot Frequency Selection.................................................................. 14
VGA Enable/Disable .................................................................................... 14
LAN1/2 Enable/Disable .............................................................................. 15
Compact Flash Master/Slave Select ........................................................... 15
SAS Enable/Disable .................................................................................... 15
SAS RAID Mode Select .............................................................................. 15
JPS2 allows you to select the SAS RAID mode, either Software RAID or IT
Mode. Close this jumper to use Software RAID (the default setting). Set this
jumper to open to use the IT Mode. ................................................................ 15
2-9 Onboard Indicators ........................................................................................... 16
LAN1/LAN2 LEDs ........................................................................................ 16
Dedicated IPMI LAN LEDs .......................................................................... 16
Power LED .................................................................................................. 16
IPMI LED ..................................................................................................... 16
2-10 Floppy, SAS and SATA Drive Connections ...................................................... 17
IDE Connectors ........................................................................................... 17
Floppy Drive Connector .............................................................................. 18
SATA Ports .................................................................................................. 18
SAS Ports .................................................................................................... 18
2-11 Enabling SATA RAID ........................................................................................ 19
Serial ATA (SATA)............................................................................................. 19
Installing the OS/SATA Driver .......................................................................... 19
Building a Driver Diskette ............................................................................ 19
H8DI3+/I+(-F) Serverboard User’s Manual
vii
Enabling SATA RAID in the BIOS ............................................................... 20
Using the Adaptec RAID Utility ........................................................................ 21
Installing the RAID Driver During OS Installation ............................................ 21
2-12 Installing Drivers ............................................................................................... 22
Supero Doctor III .............................................................................................. 23
Chapter 3 Troubleshooting
3-1 Troubleshooting Procedures .............................................................................. 1
Before Power On ............................................................................................... 1
No Power ........................................................................................................... 1
No Video ............................................................................................................ 2
Memory Errors .................................................................................................. 2
Losing the System’s Setup Con guration .......................................................... 2
3-2 Technical Support Procedures ........................................................................... 3
3-3 Frequently Asked Questions .............................................................................. 3
3-4 Returning Merchandise for Service.................................................................... 4
Chapter 4 BIOS
4-1 Introduction ......................................................................................................... 1
4-2 Main Menu ......................................................................................................... 2
4-3 Advanced Settings Menu ................................................................................... 2
4-4 Security Menu .................................................................................................. 19
4-5 Boot Menu ........................................................................................................ 19
4-6 Exit Menu ......................................................................................................... 20
Appendix A BIOS Error Beep Codes
Appendix B BIOS POST Checkpoint Codes
B-1 Uncompressed Initialization Codes .................................................................... 1
B-2 Bootblock Recovery Codes ................................................................................ 2
B-3 Uncompressed Initialization Codes .................................................................... 3
viii
Notes
Preface
Chapter 1: Introduction
1-1
Chapter 1
Introduction
1-1 Overview
Checklist
Congratulations on purchasing your computer serverboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your serverboard.
If anything listed here is damaged or missing, contact your retailer.
IDE cable (CBL-036L-03)
Floppy cable (CBL-022L)
COM port cable (CBL-010L)
SATA cable x 4 (CBL-044L)
SAS cable x2 (CBL-0097L-02) (see note below)
IO shield (MCP-260-00027-0N)
CD-ROM drivers and software (CDR-APLUS2 v 1.00 or newer)
Note: The SAS cable is not provided for the H8DII+-F or H8DII+ serverboards.
1-2
H8DI3+/I+(-F) Serverboard User’s Manual
1-2 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Paci c
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3991
Web Site: www.supermicro.com.tw
Technical Support:
Tel: 886-2-8228-1366, ext.132 or 139
Chapter 1: Introduction
1-3
Figure 1-1. H8DI3+/I+(-F) Serverboard Image
1-4
H8DI3+/I+(-F) Serverboard User’s Manual
Notes:
Jumpers not indicated are for test purposes only.
Not all ports, jumpers or LED Indicators are available on all serverboards.
Figure 1-2. H8DI3+/I+(-F) Serverboard Serverboard Layout
(not drawn to scale)
JPI2C
JPW3JPW2
JPW1
JF1
JWF1
JWOL
JPL2
JPT1
JPS1
J7
JPX1B
JPX1A
JPL1
JPB
JPG1
JWD
JPUSB1
JD1
BATTERY
SATA0 SATA2 SATA4
SATA1 SATA3 SATA5
JLPC80
FAN4
FAN3
FAN7
FAN1FAN2
FAN5
FAN8
FAN6
JL1
JOH1
JPS2
JCF1
JI2C2
JI2C1
USB6/7USB2/3
KB &
MOUSE
USB 0/1 &
IPMI LAN
COM1
VGA
LAN1
LAN2
COM2
USB4 USB5
I-BUTTON
SAS 4~7
T-SGPIO1
SAS 0~3
SMBus1
SLOT6 PCI-E 2.0 x8
SLOT5 PCI-E 2.0 x8
SLOT4 PCI-E 2.0 x8
CPU1/DIMM1B
CPU1/DIMM1A
CPU1/DIMM2B
CPU1/DIMM2A
CPU1/DIMM3B
CPU1/DIMM4B
CPU2/DIMM4A
CPU2/DIMM4B
CPU2/DIMM3A
CPU2/DIMM3B
CPU2/DIMM2A
CPU2/DIMM2B
CPU2/DIMM1A
SLOT3 PCI-E 2.0 x4
FLOPPY
JBT1:
CMOS
CLEAR
SLOT1 PCI-X 133MHz
CPU1/DIMM4A
CPU1
CPU2
CPU2/DIMM1B
SLOT2 PCI-X 133MHz
IDE#1
CPU1/DIMM3A
AMD
SR5690
NEC
uPD720400
SAS
LSI1068E
AMD
SP5100
BMC
DP5
DP4
Chapter 1: Introduction
1-5
H8DI3+/I+(-F) Serverboard Quick Reference
Jumper Description Default Setting
JBT1 CMOS Clear (See Section 2-7)
JCF1 Compact Flash Master/Slave Closed (Master)
JI
2
C1/JI
2
C2 I
2
C to PCI-E Slot Enable/Disable Both Closed (Enabled)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPL1/JPL2 LAN 1/2 Enable/Disable Pins 1-2 (Enabled)
JPS1 SAS Controller Enable/Disable Pins 1-2 (Enabled)
JPS2 SAS RAID Mode On (Software RAID)
JPX1A/JPX1B PCI-X Slot Frequency Selection Open (Auto)
JWD Watch Dog Pins 1-2 (Reset)
LED Description
LAN Ports LEDs for the LAN Ethernet ports
Dedicated IPMI LAN LEDs for the dedicated IPMI LAN Ethernet port
Power LED (DP4) LED showing power connected for serverboard
IPMI LED (DP5) LED showing IPMI connection
1-6
H8DI3+/I+(-F) Serverboard User’s Manual
Connector Description
COM1/COM2 COM1 Serial Port/Header
FAN 1-8 Chassis/CPU Fan Headers
Floppy Floppy Disk Drive Connector
I-Button I-Button Socket (for RAID 5 support)
IDE#1 IDE Disk Drive Connector
IPMI LAN Dedicated IPMI LAN Port
JD1 Speaker Header
JF1 Front Panel Connector
JL1 Chassis Intrusion Header
JOH1 Overheat Warning Header
JPI2C Power I
2
C Header
JPW1 24-pin Main ATX Power Connector
JPW2/3 +12V 8-pin CPU Power Connectors
JWF1 Compact Flash Card Power Connector
JWOL Wake-On-LAN Header
LAN1/2 Gigabit Ethernet (RJ45) Ports
PS2 Mouse/Keyboard PS2 Mouse/Keyboard connectors
SMBus System Management Bus Header
SAS0~3, SAS4~7 SAS Ports
SATA0 ~ SATA5 SATA Ports
T-SGPIO-1 Serial General Purpose Input/Output Header
USB0/1, USB4/5, USB2/3 Universal Serial Bus (USB) Ports, Headers
VGA VGA Connector
Chapter 1: Introduction
1-7
Serverboard Features
CPU
Dual AMD Opteron 2000 series (Socket F type) processors
Note: Supports 237x, 238x, 235x and 24xx processors. Please refer to our web site for further
details on supported processors.
Memory
Sixteen single/dual channel DIMM slots supporting up to 128 GB of DDR2-800
/667/533 registered ECC SDRAM
Note: Due to a CPU limitation, fully populating DIMM slots with DDR2-667 will pull the speed down to
533 MHz (see our web site for possible updates to this). Refer to Section 2-4 before installing memory
and our web site for recommended DIMMs.
Chipset
AMD SR5690/SP5100 chipset/southbridge
Expansion Slots
Two (2) PCI-Express x16 (x8 signal) slots (Slot 4 and 6)
One (1) PCI-Express x8 slot (Slot 5)
One (1) PCI-Express x8 (x4 signal) slot (Slot 3)
Two (2) PCI-X 133 slots (Slot 1: Channel B, Slot 2: Channel A)
BIOS
16 Mb AMIBIOS
®
SPI Flash ROM
APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), SMBIOS
2.3, Plug and Play (PnP)
PC Health Monitoring
Onboard voltage monitors
Fan status monitor with rmware/software on/off and speed control
Watch Dog
Environmental temperature monitoring via BIOS
Power-up mode control for recovery from AC power loss
System resource alert (via included utility program)
Auto-switching voltage regulator for the CPU core
CPU thermal trip support
I
2
C temperature sensing logic
1-8
H8DI3+/I+(-F) Serverboard User’s Manual
ACPI Features
Microsoft OnNow
Slow blinking LED for suspend state indicator
BIOS support for USB keyboard
Wake-On-LAN (WOL) and Wake-On-Ring (WOR) headers
Internal/external modem ring-on
Onboard I/O
On-chip SATA controller supporting six (6) SATA ports (RAID 0, 1, 10 sup-
ported)
LSI 1068E SAS controller (H8DI3+(-F) only, RAID 0, 1, 10 and JBOD; optional
RAID 5 support with I-Button installed).
Two (2) Fast UART 16550 compatible serial port (one header and one port)
Two on-board PCIE link INTEL 82574L Gigabit ethernet chipset supports two
Gigabit LAN ports
Six (6) USB (Universal Serial Bus 2.0) ports (2x rear, 2x header, 2x type A)
One (1) dedicated IPMI LAN port
Onboard Matrox
®
G200 graphics controller (with 16 MB DDR2 memory) sup-
ports one (1) VGA port
Other
Onboard power LED
Chassis intrusion detection
CD Utilities
BIOS ash upgrade utility
Super Doctor III
IPMI 1.5 / 2.0 (Optional)
Dimensions
Extended ATX form: 12" x 13" (310 x 330 mm)
Chapter 1: Introduction
1-9
Figure 1-3. AMD SR5690/SP5100 Chipset:
System Block Diagram
Note: This is a general block diagram and may not exactly represent
the features on your serverboard. See the previous pages for the
actual speci cations of your serverboard.
DDR2
DDR2
DDR2 533/667/800
Socket F
AMD
H0L1
HT Link
16/16-1GHz
H0L2
16/16-1GHz
HT Link
SR5690
COM1
DIMM B2
DIMM B4
AMD
Socket F
CPU2
H0L0
HT Link
16/16-1GHz
W83795G
DIMM B6
DIMM B8
DIMM A5
DIMM B6
DIMM A7 DIMM B8
DIMM A3
DIMM A1 DIMM B2
DIMM B4
DIMM A5
DIMM A7
DIMM A3
DIMM A1
DDR2 533/667/800
PCI-E GEN2 X8
Slot6
PCI-E GEN2 X8
SAS Controller
LSI 1068E
IDE (ATA/133)
SATA x6
PCI-E GEN2 X4
Slot3
PCI-E GEN2 X8
Slot4
PCI-E GEN2 X8
Slot5
PCI-X 64Bit
133/100 MHz Slot
NEC
PD720400
PCI-E GEN2 X4
PCI-X A
PCI-X B
PCI-E GEN2 X1
Intel 82574L
GbE(LAN2)
SAS x4
SAS x4
PCI-X 64Bit
133/100 MHz Slot
RJ45
SP5100
BMC
VGA
WPCM450-R
PCI
2x USB
LPC
SMBus
W83627DHG
SIOHWM
SPI Flash
KB/MS
COM2
FLOPPY
RMII
DDR2 SDRAM
64MB X16
PSU I2C
IPMB
FE PHY
RTL8201N
VGA
RJ45
2XUSB
4XUSB
Intel 82574L
GbE(LAN1)
PCI-E GEN2 X1
RJ45
1-10
H8DI3+/I+(-F) Serverboard User’s Manual
1-3 Chipset Overview
The H8DI3+/I+(-F) Serverboard serverboard is based on the AMD SR5690/SP5100
chipset. This chipset functions as a Media and Communications Processor (MCP).
Controllers for the system memory are integrated directly into AMD Opteron
processors.
AMD SR5690/SP5100 Processor
The AMD SR5690 and SP5100 are each single-chip, high-performance
HyperTransport peripheral controllers for northbridge and southbridge functions,
respectively. They both include a 46-lane PCI Express interface, an AMD Opteron
16-bit Hyper Transport interface link, a six-port Serial ATA interface, a dual-port Gb
Ethernet interface and a six-port USB 2.0 interface. The AMD SR5690 connects
directly to the CPUs.
HyperTransport Technology
HyperTransport technology is a high-speed, low latency point to point link that was
designed to increase the communication speed by a factor of up to 48x between
integrated circuits. This is done partly by reducing the number of buses in the
chipset to reduce bottlenecks and by enabling a more ef cient use of memory
in multi-processor systems. The end result is a signi cant increase in bandwidth
within the chipset.
1-4 PC Health Monitoring
This section describes the PC health monitoring features of the H8DI3+/I+(-F)
Serverboard. The serverboard has an onboard System Hardware Monitor chip that
supports PC health monitoring.
Onboard Voltage Monitors
The onboard voltage monitor will continuously scan crucial voltage levels. Once
a voltage becomes unstable, it will give a warning or send an error message to
the screen. Users can adjust the voltage thresholds to de ne the sensitivity of the
voltage monitor. Real time readings of these voltage levels are all displayed in
BIOS.
Fan Status Monitor with Firmware/Software Speed Control
The PC health monitor can check the RPM status of the cooling fans. The onboard
fans are controlled by thermal management via BIOS.
Chapter 1: Introduction
1-11
CPU Overheat/Fan Fail LED and Control
This feature is available when the user enables the CPU overheat/Fan Fail warning
function in the BIOS. This allows the user to de ne an overheat temperature. When
this temperature is exceeded or when a fan failure occurs, the Overheat/Fan Fail
warning LED is triggered.
Auto-Switching Voltage Regulator for the CPU Core
The 3-phase-switching voltage regulator for the CPU core can support up to 80A
and auto-sense voltage IDs ranging from 0.8 V to 1.55V. This will allow the regulator
to run cooler and thus make the system more stable.
1-5 Power Con guration Settings
This section describes the features of your serverboard that deal with power and
power settings.
Microsoft OnNow
The OnNow design initiative is a comprehensive, system-wide approach to system
and device power control. OnNow is a term for a PC that is always on but appears
to be off and responds immediately to user or other requests.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start blinking
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.
BIOS Support for USB Keyboard
If a USB keyboard is the only keyboard in the system, it will function like a normal
keyboard during system boot-up.
Main Switch Override Mechanism
The power button can function as a system suspend button. When the user
depresses the power button, the system will enter a SoftOff state. The monitor
will be suspended and the hard drive will spin down. Depressing the power button
again will cause the whole system to wake-up. During the SoftOff state, the power
supply provides power to keep the required circuitry in the system alive. In case the
system malfunctions and you want to turn off the power, just depress and hold the
power button for 4 seconds. The power will turn off and no power will be provided
to the serverboard.
1-12
H8DI3+/I+(-F) Serverboard User’s Manual
Wake-On-LAN (WOL)
Wake-On-LAN is de ned as the ability of a management application to remotely
power up a computer that is powered off. Remote PC setup, up-dates and access
tracking can occur after hours and on weekends so that daily LAN traf c is kept
to a minimum and users are not interrupted. The serverboard has a 3-pin header
(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has
WOL capability. Wake-On-LAN must be enabled in BIOS.
Wake-On-Ring Header (WOR)
Wake-up events can be triggered by a device such as the external modem ringing
when the system is in the SoftOff state.
1-6 Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.
The H8DI3+/I+(-F) Serverboard requires the use of proprietary power supplies.
Please refer to the pinout information for the power connectors in Section 6 of
Chapter 2 for detailed information on power requirements.
In areas where noisy power transmission is present, you may choose to install a
line lter to shield the computer from noise. It is recommended that you also install
a power surge protector to help avoid problems caused by power surges.
Warning: To prevent the possibility of explosion, do not use the wrong type of
onboard CMOS battery or install it upside down.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78

SUPER MICRO Computer MNL-H8DI3+-F User manual

Category
Server/workstation motherboards
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI