Sony MHC-VX8 Operating instructions

Category
Home audio sets
Type
Operating instructions
1
GB
Mini Hi-Fi
Component
System
©1999 by Sony Corporation
Operating Instructions
3-865-694-14(1)
f
MHC-VX8
2
GB
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
This appliance is classified
as a CLASS 1 LASER
product. The CLASS 1
LASER PRODUCT
MARKING is located on
the rear exterior.
This stereo system is equipped with the Dolby B-
type noise reduction system*.
* Manufactured under license from Dolby
Laboratories Licensing Corporation.
DOLBY and the double-D symbol a are
trademarks of Dolby Laboratories Licensing
Corporation.
This system can play
the following discs
VIDEO CDs Audio CDs
Disc logo
Contents Audio + Video Audio
(moving pictures)
Disc size 12 cm/8 cm 12 cm/8 cm
Play time 74 min./20 min. 74 min./20 min.
Note on VIDEO CDs
This system conforms to VIDEO CDs without PBC
functions (Ver. 1.1) and VIDEO CDs with PBC
functions (Ver. 2.0) of VIDEO CD standards. You
can enjoy two kinds of playback according to the
disc type.
Disc type You can
VIDEO CDs without Enjoy video playback
PBC functions (moving pictures) as
(Ver. 1.1 discs) well as audio CDs.
VIDEO CDs with Play interactive
PBC functions software using menu
(Ver. 2.0 discs) screens displayed on
the TV screen (menu
playback), in addition
to the video playback
function of VIDEO
CDs without PBC
functions.
Moreover, you can
play high or standard
quality still picture.
* PBC = Play Back Control
3
GB
Table of Contents
Getting Started
Step 1: Hooking up the system............ 4
Step 2: Setting the time ......................... 8
Step 3: Presetting radio stations .......... 9
Basic Operations
Playing a VIDEO CD ........................... 11
Playing a CD ......................................... 13
Recording a CD/VIDEO CD .............. 15
Listening to the radio........................... 16
Recording from the radio .................... 17
Playing a tape........................................ 18
Recording from a tape ......................... 20
Singing along: Karaoke ...................... 21
The VIDEO CD/CD Player
Playing a VIDEO CD with PBC
functions (Ver. 2.0) ........................ 23
Checking the remaining time ............. 24
Using the on-screen display ............... 25
Locating a specific part of a disc ........ 27
Resuming playback from the point you
stopped a VIDEO CD .................... 31
Setting the sharpness ........................... 32
Playing the CD tracks repeatedly ...... 33
Playing the CD tracks in
random order ................................. 34
Programming the CD tracks ............... 35
Playing CDs without interruption ..... 36
The Tape Deck
Recording on a tape manually ........... 37
Recording a CD by specifying track
order ................................................ 38
DJ Effects
Looping part of a CD ........................... 40
Flashing part of a CD ........................... 40
Using the drum pads ........................... 41
Using the beat functions...................... 42
Sound Adjustment
Adjusting the sound ............................ 45
Selecting the audio emphasis ............. 46
Changing the spectrum analyzer
display ............................................. 47
Selecting surround effects ................... 48
Adjusting the graphic equalizer......... 48
Making a personal audio
emphasis file................................... 49
Other Features
Mixing and recording sounds ............ 51
Falling asleep to music ........................ 52
Waking up to music ............................. 52
Timer-recording radio programs ....... 54
Optional components
Connecting audio components .......... 55
Connecting a VCR ................................ 56
Connecting external antennas ............ 57
Additional Information
Precautions ............................................ 58
Troubleshooting ................................... 59
Specifications ........................................ 62
Glossary ................................................. 64
Index........................................ Back cover
4
GB
Getting Started
Step 1: Hooking up the system
Do the following procedure 1 to 6 to hook up your system using the supplied cords and
accessories.
Notes
Keep the speaker cords away from the
antennas to prevent noise.
The type of speakers supplied vary
according to the model you purchased
(see “Specifications” on page 62).
2 Connect the speaker cords from the
surround speakers to the appropriate
SURROUND SPEAKER jacks.
1 Connect the speakers.
1
Connect the speaker cords of front
speakers to the SPEAKER jacks as below.
For the front speakers with jacks,
connect the speaker cords to the
speaker in the same way.
AM loop antenna
Front speaker (Left)Front speaker (Right)
Insert only the stripped portion.
Black/
Stripe ()
Red/
Solid ()
FM antenna
R
+
L
+
2
6
5
1
34
1 1
Surround speaker (Right) Surround speaker (Left)
To the video input
5
GB
VIDEO OUT
3 Connect the video input jack of your
TV to the VIDEO OUT jack with the
supplied video connecting cable.
When using a TV
Turn on the TV and select the video input so you
can view the pictures from this system.
Tip
For even higher quality video images, you can use
an optional S VIDEO cord to connect the S VIDEO
input jack on your TV to the S VIDEO OUT jack.
Notes
Keep the speaker cords away from
the antennas to prevent noise.
Do not place the surround speakers
on top of a TV. This may cause
distortion of the colors in the TV
screen.
Be sure to connect both left and
right surround speakers. Otherwise,
the sound will not be heard.
2 Connect the FM/AM antennas.
Set up the AM loop antenna, then
connect it.
Jack type A
Jack type B
FM75
AM
COAXIAL
Extend the FM lead
antenna horizontally.
AM loop antenna
Extend the FM lead
antenna horizontally.
AM loop antenna
FM75
AM
continued
Insert only the stripped portion.
Black/
Stripe ()
Red/
Solid ()
R
+
L
+
6
GB
VOLTAGE SELECTOR
220V
120V
230
240V
-
SYSTEM SELECT
AUTO
PALNTSC
Step 1: Hooking up the system
(continued)
4 Set SYSTEM SELECT (color system)
to the appropriate position (PAL or
NTSC), according to your TV.
If your TV automatically changes the
color system according to the input
signal:
The factory setting (AUTO) automatically
changes the color system of the video output
according to the color system of the current
VIDEO CD.
If the color system of your TV is NTSC:
Set SYSTEM SELECT to NTSC.
Pictures recorded in the PAL color system will be
stretched vertically and will be displayed with the
upper and lower parts of the picture cut off.
If the color system of your TV is PAL:
Set SYSTEM SELECT to PAL.
Pictures recorded in the NTSC color system will be
stretched horizontally and will be displayed with
the upper and lower parts of the screen masked in
black.
Note
Be sure to turn off the system before changing the
SYSTEM SELECT setting.
5 For models with a voltage selector,
set VOLTAGE SELECTOR to
position of your local power line
voltage.
6 Connect the power cord to a wall
outlet.
The demonstration appears in the
display. When you press , the
system turns on and the demonstration
automatically ends.
If the supplied adapter on the plug does
not fit your wall outlet, detach it from
the plug (only for models equipped with
an adapter).
To connect optional components
See page 55.
To deactivate the demonstration
When you set the time (Step 2: Setting the
time), the demonstration is deactivated.
To activate/deactivate the demonstration
again, press DEMO (STANDBY) while the
system is off.
7
GB
TV
TV VOL +/
TV CH +/
TV/VIDEO
To attach the front speaker pads
Attach the supplied front speaker pads to the
bottom of the speakers to stabilize the
speakers and prevent them from slipping.
Inserting two size AA (R6)
batteries into the remote
Using the remote
You can use the shaded buttons shown below
to operate Sony TV.
To Press
Turn the TV on or TV .
off
Switch the TV's TV/VIDEO.
video input
Change the TV TV CH +/–.
channels
Adjusts the volume TV VOL +/–.
of the TV speaker(s)
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates
the system, replace both batteries with new ones.
Note
If you do not use the remote for a long period of
time, remove the batteries to avoid possible damage
from battery leakage.
When carrying this system
Do the following to protect the CD
mechanism.
Make sure that all CDs are removed from the
unit.
1 Press FUNCTION repeatedly until “CD”
appears in the display.
2 Hold down CD LOOP and press to
turn off the system.
3 Disconnect the cord.
8
GB
3 Press ENTER/NEXT.
The minute indication flashes.
4 Turn the jog dial to set the minute.
5 Press ENTER/NEXT.
The clock starts working.
Tip
If you’ve made a mistake, start over from step 1.
To change the time
The previous explanation shows you how to
set the time while the power is off. To change
the time while the power is on, do the
following:
1 Press CLOCK/TIMER SET.
2 Turn the jog dial to select SET CLOCK.
3 Press ENTER/NEXT.
4 Perform steps 2 through 5 above.
Note
The clock settings are cancelled when you
disconnect the power cord or if a power failure
occurs.
1 Press CLOCK/TIMER SET.
The hour indication flashes.
2 Turn the jog dial to set the hour.
DISPLAY
Step 2: Setting the
time
You must set the time before using the timer
functions.
1
3,52,4
9
GB
Preset number
Step 3: Presetting
radio stations
You can preset the following number of
stations:
2 band model: 20 for FM, 10 for AM.
3 band model: 20 for FM, 10 for MW, and
10 for SW.
2
34
Jog dial
1
(Power)
continued
n
1 Press TUNER/BAND repeatedly
until the band you want appears in
the display.
The bands you can receive vary
depending on the model you purchased.
Be sure to check which bands you can
receive.
Every time you press this button, the
band changes as follows:
2 band model:
FM ˜ AM
3 band model:
FM n MW n SW
2 Press and hold + or – until the
frequency indication starts to
change, then release.
Scanning stops when the system tunes in
a station. “TUNED” and “STEREO” (for
a stereo program) appear.
3 Press TUNER MEMORY.
A preset number appears in the display.
The stations are stored from preset
number 1.
4 Press ENTER/NEXT.
The station is stored.
5 Repeat steps 1 to 4 to store other
stations.
10
GB
To tune in a station with a weak
signal
Press + or – repeatedly in step 2 to tune in the
station manually.
To set another station to the exist
preset number
Start over from step 1. After step 3, turn the
jog dial to select the preset number you want
to store the other station.
You can add a new preset number after the
last preset number.
To erase a preset station
1 Keep pressing TUNER MEMORY until a
preset number appears in the display.
2 Turn the jog dial to select the preset
number you want to erase.
Select “ALL ERASE” when you want to
erase all the preset stations.
3 Press ENTER/NEXT.
“COMPLETE” appears.
When you erase a preset number, the preset
number decreases by one and all preset
numbers following the erased one are
renumbered.
To change the AM tuning interval
(Except for Middle Eastern models)
The AM tuning interval is factory set to 9 kHz
(10 kHz in some areas). To change the AM tuning
interval, tune in any AM station first, then turn off
the power. While holding down the ENTER/NEXT
button, turn the power back on. When you change
the interval, AM preset stations will be erased. To
reset the interval, repeat the same procedure.
Tip
The preset stations are retained for half a day even if
you unplug the power cord or if a power failure
occurs.
Step 3: Presetting radio stations
(continued)
11
GB
Basic Operations
VOLUME
PREV
NEXT
0 )
= +
DISC SKIP/
EX-CHANGE
CD
(P
p
PLAY
MODE
1 Turn on your TV and select the
video input.
Refer to the operating instructions
supplied with your TV if you need help.
2 Press § and place up to two VIDEO
CDs on the disc tray.
If a disc is not placed properly, it will not
be recognized.
To insert a third disc, press DISC SKIP/
EX-CHANGE to rotate the disc tray.
3 Press one of the DISC 1~3 buttons.
The disc tray closes and playback starts.
If you press CD (P (or CD ( on the
remote) when the disc tray is closed,
playback starts from the CD whose
button is lit green.
(Power)
Basic Operations
Playing a VIDEO CD
You can play both VIDEO CDs without PBC
functions (Ver. 1.1) and VIDEO CDs with
PBC functions (Ver. 2.0).
You can enjoy two kinds of playback
according to the disc type.
With the label
side up. When
you play a
VIDEO CD
single, place it
on the inner
circle of the
tray.
Playing timeTrack number
3
2
continued
Disc tray number
TV
P
D.SKIP
CD (
0/)=/+
(PREV/NEXT)
p
VOL +/–
TV VOL +/–
TV CH +/–
12
GB
To Do this
Stop play Press p.
Pause Press CD (P (or P on the
remote)*
1
. Press again to
resume play.
Select a track Press NEXT to go forward,
PREV to go back.
Or, during play or pause, turn
the jog dial clockwise (to go
forward) or counterclockwise
(to go back) and release it
when you reach the desired
track. (Or press + (to go
forward) or = (to go back)
on the remote.)*
2
Find a point in a Press 0 or ) during
track or scene*
2
playback.
(Lock Search
1 Press once to start searching.
function) 2 Press again to increase the
search speed. Each time you
press the button, the speed
changes as follows:
1 (slow) n 2 (normal) n
3 (high) n 1 (slow) …
3 Press CD (P to stop
searching at the desired point.
Select a VIDEO Press a DISC 1~3 button or
CD in stop mode DISC SKIP/EX-CHANGE (or
D.SKIP on the remote).
Play only the Press PLAY MODE
VIDEO CD you repeatedly until “1 DISC”
have selected appears.
Play all VIDEO Press PLAY MODE repeatedly
CDs*
3
until “ALL DISCS” appears.
Remove the Press §.
VIDEO CD
Exchange other Press DISC SKIP/
VIDEO CDs EX-CHANGE.
while playing
Adjust the Turn VOLUME (or press VOL
volume +/– on the remote).
*
1
There may be some disturbance in the video
image.
*
2
Only for VIDEO CDs without PBC functions (Ver.
1.1).
*
3
This function cannot be used during menu
playback of a VIDEO CD with the PBC functions
(Ver. 2.0).
Tips
Pressing CD (P when the power is off
automatically turns the power on and starts
VIDEO CD playback if there is a VIDEO CD in the
tray (One Touch Play).
You can switch from another source to the VIDEO
CD player and start playing a VIDEO CD just by
pressing CD (P or the DISC 1~3 buttons
(Automatic Source Selection).
If there is no VIDEO CD in the player, “CD NO
DISC” appears in the display.
When a disc tray holding a VIDEO CD is selected
(or playing), the DISC 1~3 button for that tray
lights green. When a disc tray holding a VIDEO
CD is not selected, the DISC 1~3 button for that
tray lights orange. When all disc trays are empty,
the DISC 1~3 buttons all light green.
Playing a VIDEO CD (continued)
13
GB
Basic Operations
1 Press § and place up to two CDs on
the disc tray.
If a disc is not placed properly it will not
be recognized.
To insert a third disc, press DISC SKIP/
EX-CHANGE to rotate the disc tray.
2 Press one of the DISC 1~3 buttons.
The disc tray closes and play starts.
If you press CD (P (or CD ( on the
remote) when the disc tray is closed,
play starts from the CD loaded on the
tray whose button is lit green.
VOLUME
0 )
= +
CD
(P
p
DISC SKIP/
EX-CHANGE
PLAY
MODE
Playing a CD
— Normal play
You can play up to three CDs in a row.
With the label
side up. When
you play a single
CD, place it on
the inner circle
of the tray.
21
Disc tray number
Playing time
Track number
(Power)
continued
P
D.SKIP
CD (
0/)=/+
VOL +/
p
14
GB
To Do this
Stop play Press p.
Pause Press CD (P (P on the
remote). Press again to resume
play.
Select a track During play or pause, turn the
jog dial clockwise (to go
forward) or counterclockwise
(to go back) and release it
when you reach the desired
track. (Or press + (to go
forward) or = (to go back)
on the remote.)
Find a point in Press ) or 0 during
a track playback.
(Lock Search Press CD (P to stop
function) searching at the desired point.
Select a CD Press a DISC 1~3 button or
in stop mode DISC SKIP/EX-CHANGE.
Play only the Press PLAY MODE
CD you have repeatedly until “1 DISC”
selected appears.
Play all CDs Press PLAY MODE repeatedly
until “ALL DISCS” appears.
Remove the CD Press §.
Exchange other Press DISC SKIP/
CDs while EX-CHANGE.
playing
Adjust the Turn VOLUME (or press VOL
volume +/– on the remote).
Tips
Pressing CD (P when the power is off
automatically turns the power on and starts CD
playback if there is a CD in the tray (One Touch
Play).
You can switch from another source to the CD
player and start playing a CD just by pressing
CD (P or the DISC 1~3 buttons (Automatic
Source Selection).
If there is no CD in the player, “CD NO DISC”
appears in the display.
When a disc tray holding a CD is selected (or
playing), the DISC 1~3 button for that tray lights
green. When a disc tray holding a CD is not
selected, the DISC 1~3 button for that tray lights
orange. When all disc trays are empty, the DISC
1~3 buttons all light green.
Playing a CD (continued)
15
GB
Basic Operations
2 Press § and place a CD.
Then press again to close the disc tray.
If the indicator for the tray you want to
record is not lit green, press DISC SKIP/
EX-CHANGE repeatedly so that it lights
green.
3 Press CD SYNC.
Deck B stands by for recording and the
CD player stands by for playback. The
indicator on TAPE B ( (for front side)
lights up.
4 Press DIRECTION repeatedly to
select A to record on one side.
Select ß (or RELAY) to record on
both sides.
5 Press REC PAUSE/START.
Recording starts.
To stop recording
Press p.
Tips
If you want to record from the reverse side, press
TAPE B 9 to light its indicator after pressing CD
SYNC.
When you record on both sides, be sure to start
from the front side. If you start from the reverse
side, recording stops at the end of the reverse side.
When you want to reduce the hiss noise in low-
level high-frequency signals, press DOLBY NR so
that “DOLBY NR” appears after pressing CD
SYNC.
Note
You cannot listen to other sources while recording.
CD
(P
p
DISC SKIP/
EX-CHANGE
DOLBY NR
— CD Synchro Recording
The CD SYNC button lets you record from a
CD to a tape easily. You can use TYPE I
(normal) or TYPE II (CrO2) tapes. The
recording level is adjusted automatically.
Recording a CD /
VIDEO CD
With the side
you want to
record facing
forward
2
4
153
With the label
side up. When
you play a single
CD, place it on
the inner circle
of the tray.
(Power)
1 Press § and insert a recordable tape
into deck B.
16
GB
VOLUME
STEREO/MONO
+
=
Listening to the radio
–– Preset Tuning
Preset radio stations in the tuner's memory
first (see “Step 3: Presetting radio stations”).
2
1
Turn counter-
clockwise
(or press =
on the remote)
for lower preset
numbers.
Preset number*
Frequency
Turn clockwise
(or press +
on the remote)
for higher
preset numbers.
(Power)
1 Press TUNER/BAND repeatedly
until the band you want appears in
the display.
The bands you can receive vary
depending on the model you purchased.
Be sure to check which bands you can
receive.
Every time you press the button, the
band changes as follows:
2 band model:
FM ˜ AM
3 band model:
FM n MW n SW
2 Turn the jog dial (or press = or
+ on the remote) to tune in the
desired preset station.
* When only one station is preset, “ONE
PRESET” appears in the display.
To Do this
Turn off the radio Press .
Adjust the volume Turn VOLUME (or press
VOL +/– on the remote).
=/+
TUNER/
BAND
VOL +/–
n
17
GB
Basic Operations
Recording from the
radio
You can record the radio program on a tape
by calling up a preset station. You can use
TYPE I (normal) or TYPE II (CrO2) tapes. The
recording level is automatically adjusted.
1 Press TUNER/BAND to select the
band you want.
2 Turn the jog dial to tune in a preset
station.
+
=
p
DOLBY NR
5
3
Turn clockwise
for higher
preset numbers.
Turn counter-
clockwise for
lower preset
numbers.
1
2
To listen to non-preset radio
stations
Use manual or automatic tuning in step 2.
For manual tuning, press + or – repeatedly.
For automatic tuning, press and hold + or –.
Tips
Pressing TUNER/BAND when the power is off
automatically turns the power on and tunes to the
last received station (One Touch Play).
You can switch from another source to the radio
just by pressing TUNER/BAND (Automatic
Source Selection).
When an FM program is noisy, press
STEREO/MONO so that “MONO” appears in the
display. There will be no stereo effect, but the
reception will improve. Press the button again to
restore the stereo effect.
To improve broadcast reception, reorient the
supplied antennas.
Preset number
Frequency
4,6
(Power)
continued
18
GB
=/+
0/)
DECK A 9(
DECK B 9(
p
VOL +/–
Playing a tape
You can use any type of tape, TYPE I
(normal), TYPE II (CrO
2
) or TYPE IV (metal) ,
since the deck automatically detects the tape
type. You can also use the jog dial’s AMS*
functions to quickly search for songs you
want to hear. To select either deck A or B,
press DECK A 9( or DECK B 9( on
the remote.
* AMS (Automatic Music Sensor)
VOLUME
0 )
= +
p
DOLBY
NR
3 Press § and insert a recordable tape
into deck B.
4 Press REC PAUSE/START.
Deck B stands by for recording.
5 Press DIRECTION repeatedly to
select A to record on one side.
Select ß (or RELAY) to record on
both sides.
6 Press REC PAUSE/START.
Recording starts.
To stop recording
Press p.
Tips
If you want to record from the reverse side, press
TAPE B 9 to light its indicator after pressing
REC PAUSE/START in step 4.
When you record on both sides, be sure to start
from the front side. If you start from the reverse
side, recording stops at the end of the reverse side.
To record non-preset stations, use + and – in step 2
to tune in the desired station manually.
When you want to reduce the hiss noise in low-
level high-frequency signals, press DOLBY NR so
that “DOLBY NR” appears after pressing REC
PAUSE/START in step 4.
If noise is heard while recording from the radio,
move the respective antenna to reduce the noise.
1
2
With the side
you want to
record facing
forward
3
(Power)
Recording from the radio
(continued)
1
19
GB
Basic Operations
1 Press § and insert a recorded tape
in deck A or B.
2 Press DIRECTION repeatedly to
select A to play one side. Select
ß* to play both sides.
To play both decks in succession, select
RELAY (relay play).**
3 Press TAPE A (or TAPE B) (
(DECK A (or DECK B) 9( on the
remote).
Press TAPE A (or TAPE B) 9 to play
the reverse side. (Press DECK A (or
DECK B) 9( again on the remote to
play the reverse side.) The tape starts
playing.
With the side
you want to
play facing
forward
To Do this
Stop play Press p.
Fast-forward Press 0 or ).
Rewind Press 0 or ).
Remove the cassette Press §.
Adjust the volume Turn VOLUME (or press
VOL +/– on the remote).
* The deck stops automatically after
repeating the sequence five times.
** Relay play always follows the following
sequence:
Deck A (front side), Deck A (reverse side),
Deck B (front side), Deck B (reverse side).
Tips
Pressing TAPE A (or TAPE B) ( or 9 when the
power is off automatically turns the power on and
starts tape playback if there is a tape in the deck
(One Touch Play).
You can switch from another source to the tape
deck just by pressing TAPE A (or TAPE B) ( or
9 (Automatic Source Selection).
When you want to reduce the hiss noise in low-
level high-frequency signals, press DOLBY NR so
that “DOLBY NR” appears.
Searching for the beginning of a
track (AMS*)
During playback, turn the jog dial the same
direction as the 9 or ( indicator to go
forward. Turn the opposite direction to go
back. (Or press = or + on the remote.)
The search direction, + (forward) or – (back),
and number of songs being skipped (1~9)
appear in the display.
Example: searching forward 2 songs
* AMS (Automatic Music Sensor)
Notes
The AMS function may not operate correctly under
the following circumstances:
When the unrecorded space between songs is less
than 4 seconds long.
If completely different information is recorded on
the left and right channels.
When there are continuous sections of extremely
low level or low frequency sound (like those of a
baritone sax).
When the unit is placed near a television. (In this
case, we recommend moving the unit farther away
from the television or turning off the television.)
20
GB
Recording from a
tape
— High-speed Dubbing
3 Press DIRECTION repeatedly to
select A to record on one side.
Select ß (or RELAY) to record on
both sides.
4 Press REC PAUSE/START.
Dubbing starts.
To stop dubbing
Press p.
Tips
When you dub on both sides, start recording from
the front side. If you record from the reverse side,
recording stops at the end of the reverse side.
If you set DIRECTION to ß when the tapes you
use have different lengths, the tape in each deck
reverses independently. If you select RELAY, the
tapes in both decks reverse together.
You don’t have to set DOLBY NR, since the tape in
deck B is automatically recorded in the same state
as the tape in deck A.
You can use TYPE I (normal) or TYPE II
(CrO2) tapes. The recording level is
automatically adjusted.
1 Press § and insert a recorded tape
in deck A and a recordable tape in
deck B.
2 Press HI-DUB.
Deck B stands by for recording.
With the side
you want to
play/record
facing forward
1
41
3
(Power)
2
p
DOLBY NR
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Sony MHC-VX8 Operating instructions

Category
Home audio sets
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI