Shinko SGFW User manual

Brand: Shinko

Model: SGFW

Type: User manual

This manual is also suitable for

Instruction Manual

Pulse Transmitter

SGF, SGFW, SGWL

No. SGF21JE1 2018.11

Preface

Thank you for purchasing our SGF, SGFW and SGFL, Pulse Transmitters.

This manual contains instructions for the mounting, functions, operations and notes

when operating the instruments. To prevent accidents arising from the misuse of

these instruments, please ensure the operator receives this manual.

For detailed usage, please refer to the Instruction Manual for each instrument.

For the instrument with serial communication (SGFL), refer to the Communication

Instruction Manual. Please download detailed Instruction Manual as well as

Communication Instruction Manual from Shinko website.

http://www.shinko-technos.co.jp/e/ ĺ Products ĺ Signal Conditioners

Notes

• This instrument should be used in accordance with the specifications described in

the manual. If it is not used according to the specifications, it may malfunction or

cause a fire.

• Be sure to follow the warnings, cautions and notices. If they are not observed,

serious injury or malfunction may occur.

• The contents of this instruction manual are subject to change without notice.

• Care has been taken to ensure that the contents of this instruction manual are

correct, but if there are any doubts, mistakes or questions, please inform our sales

department.

• This instrument is designed to be installed on a DIN rail within a control panel. If it is

not, measures must be taken to ensure that the operator cannot touch power

terminals or other high voltage sections.

• Any unauthorized transfer or copying of this document, in part or in whole, is

prohibited.

• Shinko Technos Co., Ltd. is not liable for any damage or secondary damage(s)

incurred as a result of using this product, including any indirect damage.

Safety Precautions

(Be sure to read before using our products)

The safety precautions are classified into categories: “Warning” and “Caution”.

Depending on circumstances, procedures indicated by

Caution may result in

serious consequences, so be sure to follow the directions for usage.

Procedures which may lead to dangerous conditions and

cause death or serious injury, if not carried out properly.

Procedures which may lead to dangerous conditions and

cause superficial to medium injury or physical damage or may

degrade or damage the product, if not carried out properly.

Warning

•

To prevent an electrical shock or fire, only Shinko or other qualified service

personnel may handle the inner assembly.

• To prevent an electrical shock, fire or damage to the instrument, parts replacement

may only be undertaken by Shinko or other qualified service personnel.



Safety Precautions

• To ensure safe and correct use, thoroughly read and understand this

manual before using this instrument.

• This instrument is intended to be used for industrial machinery, machine

tools and measuring equipment. Verify correct usage after purpose-of-use

consultation with our agency or main office. (Never use this instrument for

medical purposes with which human lives are involved.)

• External protection devices must be installed, as malfunction of this

product could result in serious damage to the system or injury to

personnel. Proper periodic maintenance is also required.

• This instrument must be used under the conditions and environment

described in this manual. Shinko Technos Co., Ltd. does not accept liability

for any injury, loss of life or damage occurring due to the instrument being

used under conditions not otherwise stated in this manual.

Caution with Respect to Export Trade Control Ordinance

To avoid this instrument from being used as a component in, or as being

utilized in the manufacture of weapons of mass destruction (i.e. military

applications, military equipment, etc.), please investigate the end users and

the final use of this instrument. In the case of resale, ensure that this

instrument is not illegally exported.



ەInstallation Precautions

Caution

This instrument is intended to be used under the following environmental

conditions (IEC61010-1): Overvoltage category

, Pollution degree 2

Ensure the mounting location corresponds to the following conditions:

• A minimum of dust, and an absence of corrosive gases

• No flammable, explosive gases

• No mechanical vibrations or shocks

• No exposure to direct sunlight, an ambient temperature of -10 to 55

(14 to 131

) that does not change rapidly, and no icing

• An ambient non-condensing humidity of 35 to 85 %RH

• No large capacity electromagnetic switches or cables through which large

current is flowing

• No water, oil, chemicals or the vapors of these substances can come into

direct contact with the unit

•

Please note that the ambient temperature of this unit – not the ambient

temperature of the control panel – must not exceed 55

(131 ) if mounted

through the face of a control panel, otherwise the life of electronic

components (especially electrolytic capacitors) may be shortened.

Note: Avoid setting this instrument directly on or near flammable material

even though the case of this instrument is made of flame-resistant resin.

ەWiring Precautions

Caution

• Do not leave wire remnants in the instrument, because they could cause a

fire or malfunction.

• When wiring, use a crimping pliers and a solderless terminal with an

insulation sleeve in which an M3 screw fits.

• Tighten the terminal screw using the specified torque.

• This instrument does not have a power switch, circuit breaker and fuse.

Therefore, it is necessary to install a power switch, circuit breaker and fuse

externally near the instrument.

(Recommended fuse: Time-lag fuse, rated voltage 250 V AC, rated current 2 A)

• Connect the AC power to the designated terminal as is written in this

instruction manual. Otherwise, it may burn and damage the instrument.

• Do not apply a commercial power source to the sensor which is connected to

the input terminal nor allow the power source to come into contact with the

sensor.

• When wiring, keep Input/Output wires away from AC power sources.

ەOperation and Maintenance Precautions

Caution

• Do not touch live terminals. This may cause an electrical shock or problems

in operation.

• Turn the power supply to the instrument OFF before retightening the terminal

or cleaning. Working on or touching the terminal with the power switched ON

may result in severe injury or death due to electrical shock.

• Use a soft, dry cloth when cleaning the instrument.

(Alcohol based substances may tarnish or deface the unit.)

• As the display section is vulnerable, be careful not to put pressure on,

scratch or strike it with a hard object.

1. Name and Functions

1.1 Front Panel

(Fig. 1.1-1)

ձ Display section Indicates setting contents, input value and output value.

ղ Mounting screw Used for fixing the instrument to the socket or removal from it.

ճ DISP key Switches the displays, and moves to the next setting item.

Releases the lock status of the DISP key by pressing and

holding for 3 seconds.

մ SET key Selects either a setting mode or a display mode.

Shifts the digit on the Custom display.

Enters the setting mode by pressing and holding for 5

seconds.

յ SHIFT key Shifts the digit of setting value.

ն UP key Increases the numerical value.

Contents of Multi-Display A and B can be changed alternately

when Default Display is RUN display mode.

շ DOWN key

Decreases the numerical value.

Enters Manual mode by pressing and holding for 3 seconds.

ձ

ղ

ճ

ն

շ

մ

յ

Caution

Warning

࿴ᩥࡣ⿬㠃ࢆࡈぴୗࡉ࠸ࠋ

1.2 Display Section

(Fig. 1.2-1)

ձ Setting display

indicator A

Lights up in Manual mode.

ղ Input indicator A Lights up when Multi-Display A indicates an input value.

Alarm indicator A

Lights up if an input error occurs in any display mode except

All unlit display mode.

մ mA indicato

Lights up when mA is selected in [Indication unit].

յ % indicato

Lights up when % is selected in [Indication unit].

ն Input indicato

B Lights up when Multi-Display B indicates an input value.

Alarm indicator B

Lights up if an input error occurs while Multi-Display B

indicates an input value.

Setting display

indicator B

Lights up while in a setting display.

չ 1 indicator A Lights up in Manual mode.

պ Multi-Display A Indicates the following in accordance with the display

indication: Input value, custom characters, setting item

indicato

Lights up when V is selected in [Indication unit].

ռ °C indicato

Lights up when °C is selected in [Indication unit].

ս 2 indicato

B(*) Lights up for Output 2 setting display.

վ 1 indicato

B Lights up for Output 1 setting display.

տ Multi-Display B Indicates the following in accordance with the display

indication: Input value, custom characters, setting value

Output indicators A and B, Alarm indicators A and B: Red, Other indicators: White

(*) Applicable to the SGFWonly.

2. Mounting

2.1 Dimensions (Scale: mm)

(Fig. 2.1-1)



socket (SGF, SGFL) 11P socket (SGFW)

(Fig. 2.1-2)

2.2 Mounting to, and Removal from the DIN Rail

Mounting to the DIN Rail (Fig. 2.2-1)

ձ Separate the instrument from the socket

by loosening the mounting screw on the

front panel.

ղ Make sure the lock lever of the socket is

located in the lower part of the socket.

Hook the upper side of the socket on the

DIN rail, and fit the lower part of the socket

to the DIN rail. (A clicking sound should

be heard when done properly.)

(Fig. 2.2-1)

Caution

• Before inserting the instrument into the socket, wire the cable. (Refer to “3.

Wiring”.)

• When inserting or removing the socket, make sure the socket is oriented

vertically. If force is applied in any other direction than vertically, a malfunction

may occur.

• If the mountin

screw is fastened too ti

htl

, a malfunction ma

occur.

ճ Insert the unit into the socket.

մ Fasten the mounting screw by turning it

clockwise, to secure the unit onto the socket.

Tighten the screw lightly.

Removal from the DIN Rail (Fig. 2.2-2)

ձ Turn the power to the instrument OFF.

ղ Separate the instrument from the socket

by loosening the mounting screw on the

front panel.

ճ Insert a flat blade screwdriver into the lock

lever (lower part of the socket), and remove

the socket from the DIN rail while pulling the

lever down.

(Fig. 2.2-2)

3. Wiring

Lead Wire Solderless Terminal

Use a solderless terminal with an insulation sleeve in which an M3 screw fits

as shown below. The torque should be 0.63 N•m.

Y-type (Scale: mm) Ring-type (Scale: mm)

(Fig. 3-1)

For the terminal arrangement, refer to the Instruction Manual (Detailed

version) or Specification Sheet for each unit.

Inquiries

For any inquiries about this unit, please contact our agency or the vendor where

you purchased the unit after checking the following.

(e.g.)

• Model ----------------------- SGFW-F0OO-0-0

• Serial number ------------- 154F05000

In addition to the above, please let us know the details of the malfunction, or

discrepancy, and the operating conditions.

SHINKO TECHNOS CO., LTD.

URL: http://www.shinko-technos.co.jp/e/

2-5-1, Senbahigashi, Minoo, Osaka,

562-0035,

Japan

TEL: +81-72-727-6100 FAX: +81-72-727-7006

Solderless

Terminal

Manufacturer Model

Y-type

Nichifu Terminal Industries Co., Ltd. TMEV1.25Y-3

Japan Solderless Terminal MFG Co., Ltd. VD1.25-B3A

Ring-type

Nichifu Terminal Industries Co., Ltd. TMEV1.25-3

Japan Solderless Terminal MFG Co., Ltd. V1.25-3

DIN rail

Lock lever

DIN rail

ྲྀᢅㄝ᫂᭩ ࣃࣝࢫኚ᥮ჾ SGF, SGFW, SGFL

No. SGF21JE1 2018.11

ࡣࡌࡵ࡟

ࡇࡢࡓࡧࡣ㸪ࣃࣝࢫኚ᥮ჾ SGF㸪SGFW ࡲࡓࡣ SGFL(௨ୗ㸪ᮏჾ)ࢆ࠾㈙࠸ୖࡆ

㡬ࡁࡲࡋ࡚㸪ࡲࡇ࡜࡟࠶ࡾࡀ࡜࠺ࡈࡊ࠸ࡲࡋࡓࠋ

ᮏྲྀᢅㄝ᫂᭩(௨ୗ㸪ᮏ᭩)ࡣ㸪ᮏჾࡢタ⨨᪉ἲ㸪ᶵ⬟㸪᧯స᪉ἲ࠾ࡼࡧྲྀᢅ࠸࡟ࡘ

࠸࡚⡆༢࡟ㄝ᫂ࡋࡓࡶࡢ࡛ࡍࠋ

ᮏ᭩ࢆࡼࡃ࠾ㄞࡳ㡬ࡁ㸪༑ศ⌮ゎࡉࢀ࡚࠿ࡽࡈ౑⏝ࡃࡔࡉ࠸ࡲࡍࡼ࠺࠾㢪࠸⮴ࡋ

ࡲࡍࠋ

ࡲࡓ㸪ㄗࡗࡓྲྀᢅ࠸࡞࡝࡟ࡼࡿ஦ᨾ㜵ṆࡢⅭ㸪ᮏ᭩ࡣ᭱⤊ⓗ࡟ᮏჾࢆ࠾౑࠸࡟࡞

ࡿ᪉ࡢ࠾ᡭඖ࡟㸪☜ᐇ࡟ᒆࡅࡽࢀࡿࡼ࠺࠾ྲྀࡾィࡽ࠸ࡃࡔࡉ࠸ࠋ

ヲ⣽࡞౑⏝᪉ἲࡘ࠸࡚ࡣྛᶵ✀ࡢྲྀᢅㄝ᫂᭩(ヲ⣽∧)ࢆཧ↷ࡋ࡚ࡃࡔࡉ࠸ࠋ

ࡲࡓ㸪ࢩࣜ࢔ࣝ㏻ಙ௜ຍ᫬(SGFL)ࡣ㏻ಙྲྀᢅㄝ᫂᭩ࡶేࡏ࡚ཧ↷ࡋ࡚ࡃࡔࡉ࠸ࠋ

ྛᶵ✀ࡢྲྀᢅㄝ᫂᭩(ヲ⣽∧)࠾ࡼࡧ㏻ಙྲྀᢅㄝ᫂᭩ࡣ㸪ୗグᘢ♫ Web ࢧ࢖ࢺࡼࡾ

ࢲ࣮࢘ࣥࣟࢻࡋ࡚ࡃࡔࡉ࠸ࠋ

http://www.shinko-technos.co.jp ĺ ྲྀࡾᢅ࠸〇ရ ĺ ኚ᥮ჾ

ࡈὀព

࣭ᮏჾࡣ㸪グ㍕ࡉࢀࡓ௙ᵝ⠊ᅖෆ࡛౑⏝ࡋ࡚ࡃࡔࡉ࠸ࠋ

௙ᵝ⠊ᅖእ࡛౑⏝ࡋࡓሙྜ㸪ⅆ⅏㸪ᮏჾࡢᨾ㞀ࡢཎᅉ࡟࡞ࡾࡲࡍࠋ

࣭ᮏ᭩࡟グ㍕ࡉࢀ࡚࠸ࡿ㆙࿌஦㡯㸪ὀព஦㡯ࢆᚲࡎᏲࡗ࡚ࡃࡔࡉ࠸ࠋ

ࡇࢀࡽࡢ㆙࿌஦㡯㸪ὀព஦㡯ࢆᏲࡽ࡞࠿ࡗࡓሙྜ㸪㔜኱࡞യᐖࡸ஦ᨾ࡟ࡘ࡞ࡀ

ࡿᜍࢀࡀ࠶ࡾࡲࡍࠋ

࣭ᮏ᭩ࡢグ㍕ෆᐜࡣ㸪ᑗ᮶ண࿌࡞ࡋ࡟ኚ᭦ࡍࡿࡇ࡜ࡀ࠶ࡾࡲࡍࠋ

࣭ᮏ᭩ࡢෆᐜ࡟㛵ࡋ࡚ࡣ୓඲ࢆᮇࡋ࡚࠸ࡲࡍࡀ㸪୓୍ࡈ୙ᑂ࡞Ⅼࡸㄗࡾ➼࠾Ẽ࡙

ࡁࡢࡇ࡜ࡀ࠶ࡾࡲࡋࡓࡽ㸪࠾ᡭᩘ࡛ࡍࡀ࠾㈙࠸ୖࡆ࠸ࡓࡔࡁࡲࡋࡓ㈍኎ᗑࡲ࡛

ࡈ㐃⤡ࡃࡔࡉ࠸ࠋ

࣭ᮏჾࡣไᚚ┙ෆ DIN ࣮ࣞࣝ࡟タ⨨ࡋ࡚౑⏝ࡍࡿࡇ࡜ࢆ๓ᥦ࡟〇సࡋ࡚࠸ࡲࡍࠋ

౑⏝⪅ࡀ㟁※➃Ꮚ➼ࡢ㧗㟁ᅽ㒊࡟㏆࡙࠿࡞࠸ࡼ࠺࡞ฎ⨨ࢆ᭱⤊〇ရഃ࡛⾜ࡗ࡚

ࡃࡔࡉ࠸ࠋ

࣭ᮏ᭩ࡢグ㍕ෆᐜࡢ୍㒊ࡲࡓࡣ඲㒊ࢆ↓᩿࡛㌿㍕㸪」〇ࡍࡿࡇ࡜ࡣ⚗Ṇࡉࢀ࡚࠸

ࡲࡍࠋ

࣭ᮏჾࢆ㐠⏝ࡋࡓ⤖ᯝࡢᙳ㡪࡟ࡼࡿᦆᐖ㸪ண ୙ྍ⬟࡞ᮏჾࡢḞ㝗࡟ࡼࡿᦆᐖ㸪

ࡑࡢ௚ࡍ࡭࡚ࡢ㛫᥋ⓗᦆᐖ࡟ࡘ࠸࡚㸪࠸ࡗࡉ࠸㈐௵ࢆ㈇࠸࠿ࡡࡲࡍࡢ࡛ࡈ஢ᢎ

ࡃࡔࡉ࠸ࠋ

Ᏻ඲ୖࡢࡈὀព(ࡈ౑⏝๓࡟ᚲࡎ࠾ㄞࡳࡃࡔࡉ࠸ࠋ)

Ᏻ඲ୖࡢࡈὀព࡛ࡣ㸪Ᏻ඲ὀព஦㡯ࡢࣛࣥࢡࢆ"㆙࿌㸪ὀព"࡜ࡋ࡚༊ศࡋ࡚࠸ࡲ

ࡍࠋ

࡞࠾㸪

ὀព࡟グ㍕ࡋࡓ஦㡯࡛ࡶ㸪≧ἣ࡟ࡼࡗ࡚ࡣ㔜኱࡞⤖ᯝ࡟⤖ࡧࡘࡃྍ⬟

ᛶࡀ࠶ࡾࡲࡍࡢ࡛㸪グ㍕ࡋ࡚࠸ࡿ஦᯶ࡣᚲࡎᏲࡗ࡚ࡃࡔࡉ࠸ࠋ

ྲྀᢅ࠸ࢆㄗࡗࡓሙྜ㸪༴㝤࡞≧ἣࡀ㉳ࡇࡾ࠼࡚㸪ே࿨ࡸ㔜

኱࡞യᐖ࡟࠿࠿ࢃࡿ஦ᨾࡢ㉳ࡇࡿྍ⬟ᛶࡀ᝿ᐃࡉࢀࡿሙྜࠋ

ྲྀᢅ࠸ࢆㄗࡗࡓሙྜ㸪༴㝤࡞≧ἣࡀ㉳ࡇࡾ࠼࡚㸪୰⛬ᗘࡢ

യᐖࡸ㍍യࢆཷࡅࡿྍ⬟ᛶࡀ᝿ᐃࡉࢀࡿሙྜ㸪࠾ࡼࡧᶵჾ

ᦆയࡢⓎ⏕ࡀ᝿ᐃࡉࢀࡿሙྜࠋ

㆙࿌

࣭ឤ㟁࠾ࡼࡧⅆ⅏㜵ṆࡢⅭ㸪㈍኎ᗑࡢࢧ࣮ࣅࢫ࣐ࣥ௨እࡣᮏჾෆ㒊࡟ゐࢀ࡞

࠸࡛ࡃࡔࡉ࠸ࠋ

࣭ឤ㟁㸪ⅆ⅏஦ᨾ࠾ࡼࡧᶵჾᨾ㞀㜵ṆࡢⅭ㸪㒊ရࡢ஺᥮ࡣ㈍኎ᗑࡢࢧ࣮ࣅࢫ

࣐ࣥ௨እࡣ⾜ࢃ࡞࠸࡛ࡃࡔࡉ࠸ࠋ

Ᏻ඲࡟㛵ࡍࡿࡈὀព

࣭ṇࡋࡃᏳ඲࡟࠾౑࠸࠸ࡓࡔࡃࡓࡵ㸪ࡈ౑⏝ࡢ๓࡟ࡣᚲࡎᮏ᭩ࢆࡼࡃ࠾ㄞࡳ

ࡃࡔࡉ࠸ࠋ

࣭ᮏჾࡣ㸪⏘ᴗᶵᲔ࣭ᕤసᶵᲔ࣭ィ ᶵჾ࡟౑⏝ࡉࢀࡿ஦ࢆពᅗࡋ࡚࠸ࡲࡍࠋ

㈍኎ᗑ࡟౑⏝┠ⓗࢆࡈᥦ♧ࡢୖ㸪ṇࡋ࠸౑࠸᪉ࢆࡈ☜ㄆࡃࡔࡉ࠸ࠋ(ே࿨࡟

࠿࠿ࢃࡿ་⒪ᶵჾ➼࡟ࡣ㸪ࡈ౑⏝࡟࡞ࡽ࡞࠸࡛ࡃࡔࡉ࠸ࠋ)

࣭ᮏჾࡢᨾ㞀ࡸ␗ᖖ࡛ࢩࢫࢸ࣒ࡢ㔜኱࡞஦ᨾࢆᘬࡁ㉳ࡇࡍሙྜ࡟ࡣ㸪஦ᨾ㜵

Ṇࡢࡓࡵ㸪እ㒊࡟㐺ษ࡞ಖㆤ⿦⨨ࢆタ⨨ࡋ࡚ࡃࡔࡉ࠸ࠋ

ࡲࡓ㸪ᐃᮇⓗ࡞࣓ࣥࢸࢼࣥࢫࢆ㈍኎ᗑ࡟౫㢗(᭷ൾ)ࡋ࡚ࡃࡔࡉ࠸ࠋ

࣭ᮏ᭩࡟グ㍕ࡢ࡞࠸᮲௳࣭⎔ቃୗ࡛ࡣ౑⏝ࡋ࡞࠸࡛ࡃࡔࡉ࠸ࠋ

ᮏ᭩࡟グ㍕ࡢ࡞࠸᮲௳࣭⎔ቃୗ࡛౑⏝ࡉࢀࡓሙྜ㸪≀ⓗ࣭ேⓗᦆᐖࡀⓎ⏕

ࡋ࡚ࡶ㸪ࡑࡢ㈐௵ࢆ㈇࠸࠿ࡡࡲࡍࡢ࡛ࡈ஢ᢎࡃࡔࡉ࠸ࠋ



㍺ฟ㈠᫆⟶⌮௧࡟㛵ࡍࡿࡈὀព

኱㔞◚ቯරჾ(㌷஦⏝㏵࣭㌷஦タഛ➼)࡛౑⏝ࡉࢀࡿ஦ࡀ࡞࠸ࡼ࠺㸪᭱⤊⏝㏵

ࡸ᭱⤊ᐈඛࢆㄪᰝࡋ࡚ࡃࡔࡉ࠸ࠋ

ᑦ㸪෌㈍኎࡟ࡘ࠸࡚ࡶ୙ṇ࡟㍺ฟࡉࢀ࡞࠸ࡼ࠺㸪༑ศ࡟ὀពࡋ࡚ࡃࡔࡉ࠸ࠋ

ەྲྀࡾ௜ࡅୖࡢὀព

ὀ ព

[ᮏჾࡣ㸪ḟࡢ⎔ቃ௙ᵝ࡛౑⏝ࡉࢀࡿࡇ࡜ࢆពᅗࡋ࡚࠸ࡲࡍࠋ(IEC61010-1)]

࣭㐣㟁ᅽ࢝ࢸࢦࣜ

㸪ởᰁᗘ2

[ᮏჾࡣ㸪ୗグࡢࡼ࠺࡞ሙᡤ࡛ࡈ౑⏝ࡃࡔࡉ࠸ࠋ]

࣭ሻᇕࡀᑡ࡞ࡃ㸪⭉⼃ᛶ࢞ࢫࡢ࡞࠸࡜ࡇࢁࠋ

࣭ྍ⇞ᛶ㸪⇿Ⓨᛶ࢞ࢫࡢ࡞࠸࡜ࡇࢁࠋ

࣭ᶵᲔⓗ᣺ືࡸ⾪ᧁࡢᑡ࡞࠸࡜ࡇࢁࠋ

࣭┤ᑕ᪥ගࡀ࠶ࡓࡽࡎ㸪࿘ᅖ ᗘࡀ-10㹼55

࡛ᛴ⃭࡞ ᗘኚ໬࠾ࡼࡧị⤖

ࡢྍ⬟ᛶࡀ࡞࠸࡜ࡇࢁࠋ

࣭‵ᗘࡀ35㹼85 %RH࡛㸪⤖㟢ࡢྍ⬟ᛶࡀ࡞࠸࡜ࡇࢁࠋ

࣭኱ᐜ㔞ࡢ㟁☢㛤㛢ჾࡸ㸪኱㟁ὶࡢὶࢀ࡚࠸ࡿ㟁⥺࠿ࡽ㞳ࢀ࡚࠸ࡿ࡜ࡇࢁࠋ

࣭Ỉ㸪Ἔ࠾ࡼࡧ⸆ရࡲࡓࡣࡑࢀࡽࡢ⵨Ẽࡀ┤᥋࠶ࡓࡿᜍࢀࡢ࡞࠸࡜ࡇࢁࠋ

࣭ไᚚ┙ෆ࡟タ⨨ࡍࡿሙྜ㸪ไᚚ┙ࡢ࿘ᅖ ᗘ࡛ࡣ࡞ࡃ㸪ᮏჾࡢ࿘ᅖ ᗘࡀ

ࢆ㉸࠼࡞࠸ࡼ࠺࡟ࡋ࡚ࡃࡔࡉ࠸ࠋ

ᮏჾࡢ㟁Ꮚ㒊ရ(≉࡟㟁ゎࢥࣥࢹࣥࢧ)ࡢᑑ࿨ࢆ⦰ࡵࡿᜍࢀࡀ࠶ࡾࡲࡍࠋ

ͤཧ ⪃: ᮏჾࡢࢣ࣮ࢫᮦ㉁ࡣ㸪㞴⇞ᛶᶞ⬡ࢆ౑⏝ࡋ࡚࠸ࡲࡍࡀ㸪⇞࠼ࡸࡍ࠸

ࡶࡢࡢࡑࡤ࡟ࡣタ⨨ࡋ࡞࠸࡛ࡃࡔࡉ࠸ࠋ

ࡲࡓ㸪⇞࠼ࡸࡍ࠸≀ࡢୖ࡟┤᥋⨨ࡃࡇ࡜ࡣࡋ࡞࠸࡛ࡃࡔࡉ࠸ࠋ

ە㓄⥺ୖࡢὀព

ὀ ព

࣭㓄⥺సᴗࢆ⾜࠺ሙྜ㸪㟁⥺ᒌࢆᮏჾࡢ㏻㢼❆࡬ⴠ࡜ࡋ㎸ࡲ࡞࠸࡛ࡃࡔࡉ࠸ࠋ

ⅆ⅏㸪ᨾ㞀㸪ㄗືసࡢཎᅉ࡜࡞ࡾࡲࡍࠋ

࣭ᮏჾࡢ➃Ꮚ࡟㓄⥺సᴗࢆ⾜࠺ሙྜ㸪M3ࡡࡌ࡟㐺ྜࡍࡿ⤯⦕ࢫ࣮ࣜࣈ௜ᅽ╔

➃Ꮚ࠾ࡼࡧᅽ╔ᕤලࢆ౑⏝ࡋ࡚ࡃࡔࡉ࠸ࠋ

࣭➃Ꮚࡡࡌࢆ⥾ࡵ௜ࡅࡿሙྜ㸪㐺ṇ⥾ࡵ௜ࡅࢺࣝࢡ௨ෆ࡛⥾ࡵ௜ࡅ࡚ࡃࡔࡉ

࠸ࠋ

࣭ᮏჾࡣ㟁※ࢫ࢖ࢵࢳ㸪㐽᩿ჾ࠾ࡼࡧࣄ࣮ࣗࢬࢆෆⶶࡋ࡚࠸ࡲࡏࢇࠋ

ᚲࡎᮏჾࡢ㏆ࡃ࡟㟁※ࢫ࢖ࢵࢳ㸪㐽᩿ჾ࠾ࡼࡧࣄ࣮ࣗࢬࢆู㏵タࡅ࡚ࡃࡔ

ࡉ࠸ࠋ

(᥎ዡࣄ࣮ࣗࢬ: ᐃ᱁㟁ᅽ250 V AC㸪ᐃ᱁㟁ὶ: 2 Aࡢࢱ࢖࣒ࣛࢢࣄ࣮ࣗࢬ)

࣭AC㟁※ࡢ㓄⥺ࡣ㸪ᮏ᭩࡟グ㍕ࡋ࡚࠸ࡿ㏻ࡾ㸪ᑓ⏝ࡢ➃Ꮚ࡟㓄⥺ࡋ࡚ࡃࡔࡉ

࠸ࠋ

AC㟁※ࢆ௚ࡢ➃Ꮚ࡟㓄⥺ࡍࡿ࡜㸪ᮏჾࢆ↝ᦆࡋࡲࡍࠋ

࣭ධຊ➃Ꮚ࡟᥋⥆ࡉࢀࡿࢭࣥࢧ࡟㸪ၟ⏝㟁※ࡀ᥋ゐࡲࡓࡣ༳ຍࡉࢀ࡞࠸ࡼ࠺

࡟ࡋ࡚ࡃࡔࡉ࠸ࠋ

࣭ධฟຊ⥺࡜㟁※⥺ࡣ㞳ࡋ࡚㓄⥺ࡋ࡚ࡃࡔࡉ࠸ࠋ

ە㐠㌿㸪ಖᏲ᫬ࡢὀព

ὀ ព

࣭ឤ㟁㜵Ṇ࠾ࡼࡧᶵჾᨾ㞀㜵ṆࡢⅭ㸪㏻㟁୰࡟ࡣ➃Ꮚ࡟ゐࢀ࡞࠸࡛ࡃࡔࡉ࠸ࠋ

࣭➃Ꮚࡢቑ⥾ࡵ࠾ࡼࡧΎᤲ➼ࡢసᴗࢆ⾜࠺᫬ࡣ㸪ᮏჾࡢ㟁※ࢆษࡗࡓ≧ែ࡛

⾜ࡗ࡚ࡃࡔࡉ࠸ࠋ

㟁※ࢆධࢀࡓ≧ែ࡛సᴗࢆ⾜࠺࡜㸪ឤ㟁ࡢⅭ㸪ே࿨ࡸ㔜኱࡞യᐖ࡟࠿࠿ࢃ

ࡿ஦ᨾࡢ㉳ࡇࡿྍ⬟ᛶࡀ࠶ࡾࡲࡍࠋ

࣭ᮏჾࡢởࢀࡣ㸪ᰂࡽ࠿࠸ᕸ㢮࡛஝ᣔࡁࡋ࡚ࡃࡔࡉ࠸ࠋ

(ࢩࣥࢼ㢮ࢆ౑⏝ࡋࡓሙྜ㸪ᮏჾࡢኚᙧ㸪ኚⰍࡢᜍࢀࡀ࠶ࡾࡲࡍ)

࣭⾲♧㒊ࡣയࡘࡁࡸࡍ࠸ࡢ࡛㸪◳࠸≀࡛᧿ࡗࡓࡾ㸪྇࠸ࡓࡾ࡞࡝ࡣࡋ࡞࠸࡛

ࡃࡔࡉ࠸ࠋ

1. ྛ㒊ࡢྡ⛠࡜ࡣࡓࡽࡁ

1.1 ๓㠃

(ᅗ 1.1-1)

ձ ⾲♧㒊タᐃෆᐜࡸධຊ್㸪ฟຊ㔞ࢆ⾲♧ࡋࡲࡍࠋ

ղ ྲྀ௜ࡡࡌ ᮏჾࢆࢯࢣࢵࢺ࡟ᅛᐃࡍࡿሙྜ㸪ࡲࡓࡣࢯࢣࢵࢺ࠿ࡽእࡍሙ

ྜ࡟౑⏝ࡋࡲࡍࠋ

ճ DISP࣮࢟ ⏬㠃⾲♧ࡢษࡾ᭰࠼㸪タᐃ㡯┠ࢆ⛣⾜ࡋࡲࡍࠋ

3⛊㛫ᢲࡋ⥆ࡅࡿ࡜㸪DISP࣮࢟ࡢࣟࢵࢡゎ㝖ࢆ⾜࠸ࡲࡍࠋ

մ SET࣮࢟ ࣮ࣔࢻ(タᐃ࣮ࣔࢻ࡜⾲♧࣮ࣔࢻ)ࡢ㑅ᢥࢆ⾜࠸ࡲࡍࠋ

࢝ࢫࢱ࣒⏬㠃࡛ࡣ᱆⛣ືࢆ⾜࠸ࡲࡍࠋ

5⛊㛫ᢲࡋ⥆ࡅࡿ࡜㸪タᐃ࣮ࣔࢻ࡬⛣⾜ࡋࡲࡍࠋ

յ ࢩࣇࢺ࣮࢟ タᐃ್ࡢ᱆⛣ືࢆ⾜࠸ࡲࡍࠋ

ն ࢔ࢵࣉ࣮࢟ ᩘ್ࢆቑຍࡉࡏࡲࡍࠋ

ࢹࣇ࢛ࣝࢺ⏬㠃ࡀ㐠㌿⏬㠃࣮ࣔࢻࡢሙྜ㸪࣐ࣝࢳ⾲♧ჾA㸪

࣐ࣝࢳ⾲♧ჾBࡢ⾲♧ෆᐜࢆධࢀ᭰࠼ࡲࡍࠋ

շ ࢲ࣮࢘ࣥ࢟ ᩘ್ࢆῶᑡࡉࡏࡲࡍࠋ

3⛊㛫ᢲࡋ⥆ࡅࡿ࡜㸪࣐ࢽࣗ࢔࣮ࣝࣔࢻ࡬⛣⾜ࡋࡲࡍࠋ

ὀព

㆙࿌

For the English manual, see the reverse.

ձ

ղ

ճ

ն

շ

մ

յ

1.2 ⾲♧㒊

(ᅗ1.2-1)

ձ タᐃ⏬㠃⾲♧ⅉA ࣐ࢽࣗ࢔࣮ࣝࣔࢻ᫬Ⅼⅉࡋࡲࡍࠋ

ղ ධຊ⾲♧ⅉA ࣐ࣝࢳ⾲♧ჾAࡀධຊ್⾲♧᫬Ⅼⅉࡋࡲࡍࠋ

ճ ࢔࣮࣒ࣛ⾲♧ⅉA ඲ᾘⅉ⾲♧࣮ࣔࢻ௨እࡢ⾲♧࣮ࣔࢻ࡛ධຊ␗ᖖ᫬Ⅼⅉࡋࡲ

ࡍࠋ

մ mA༢఩⾲♧ⅉ ༢఩⾲♧㑅ᢥ࡛mAࢆ㑅ᢥࡋࡓሙྜⅬⅉࡋࡲࡍࠋ

յ %༢఩⾲♧ⅉ ༢఩⾲♧㑅ᢥ࡛%ࢆ㑅ᢥࡋࡓሙྜⅬⅉࡋࡲࡍࠋ

ն ධຊ⾲♧ⅉB ࣐ࣝࢳ⾲♧ჾBࡀධຊ್⾲♧᫬Ⅼⅉࡋࡲࡍࠋ

շ ࢔࣮࣒ࣛ⾲♧ⅉB ࣐ࣝࢳ⾲♧ჾBࡀධຊ್⾲♧࡛ධຊ␗ᖖ᫬Ⅼⅉࡋࡲࡍࠋ

ո タᐃ⏬㠃⾲♧ⅉB タᐃ⏬㠃᫬Ⅼⅉࡋࡲࡍࠋ

չ 1⾲♧ⅉA ࣐ࢽࣗ࢔࣮ࣝࣔࢻ᫬Ⅼⅉࡋࡲࡍࠋ

պ ࣐ࣝࢳ⾲♧ჾA ⏬㠃⾲♧࡟ᛂࡌࡓෆᐜ(ධຊ್㸪࢝ࢫࢱ࣒⾲♧㸪タᐃ㡯┠⾲

♧)ࢆ⾲♧ࡋࡲࡍࠋ

ջ V༢఩⾲♧ⅉ ༢఩⾲♧㑅ᢥ࡛Vࢆ㑅ᢥࡋࡓሙྜⅬⅉࡋࡲࡍࠋ

ռ °C༢఩⾲♧ⅉ ༢఩⾲♧㑅ᢥ࡛°Cࢆ㑅ᢥࡋࡓሙྜⅬⅉࡋࡲࡍࠋ

ս 2⾲♧ⅉB(*) ฟຊ2タᐃ⏬㠃᫬Ⅼⅉࡋࡲࡍࠋ

վ 1⾲♧ⅉB ฟຊ1タᐃ⏬㠃᫬Ⅼⅉࡋࡲࡍࠋ

տ ࣐ࣝࢳ⾲♧ჾB ⏬㠃⾲♧࡟ᛂࡌࡓෆᐜ(ධຊ್㸪࢝ࢫࢱ࣒⾲♧㸪タᐃ್⾲♧)

ࢆ⾲♧ࡋࡲࡍࠋ

ͤฟຊ⾲♧ⅉ A㸪B ࠾ࡼࡧ࢔࣮࣒ࣛ⾲♧ⅉ A㸪B ࡣ㉥Ⰽࠋ௚ࡢ⾲♧ⅉࡣⓑⰍࠋ

(*): SGFW ࡢࡳ㐺⏝ࠋ

2. ྲྀࡾ௜ࡅ

2.1 እᙧᑍἲᅗ(༢఩: mm)

(ᅗ 2.1-1)

8P ࢯࢣࢵࢺ(SGF㸪SGFL) 11P ࢯࢣࢵࢺ(SGFW)

(ᅗ 2.1-2)

2.2 DIN ࣮ࣞࣝ࡬ࡢྲྀࡾ௜ࡅ㸪ྲྀࡾእࡋ

DIN ࣮ࣞࣝ࡬ࡢྲྀࡾ௜ࡅ

ձᮏჾ๓㠃ࡢྲྀ௜ࡡࡌࢆ⦆ࡵ࡚㸪ᮏჾࢆࢯࢣࢵࢺ

࠿ࡽእࡋ࡚ࡃࡔࡉ࠸ࠋ

ղࢯࢣࢵࢺࡣ㸪ࣟࢵࢡࣞࣂ࣮ࡀ࠶ࡿ᪉ࢆୗ࡟ࡋ࡚

ࡃࡔࡉ࠸ࠋࢯࢣࢵࢺࡢୖ㒊ࢆ DIN ࣮ࣞࣝ࡟ᘬࡗ

᥃ࡅ㸪ୗ㒊ࢆᢲࡋ࡚ࡃࡔࡉ࠸ࠋ

(࢝ࢳࢵ࡜㡢ࡀࡋࡲࡍ)(ᅗ 2.2-1)

(ᅗ 2.2-1)

ὀ ព

࣭ᮏჾࢆࢯࢣࢵࢺ࡟ᤄࡋ㎸ࡴ๓࡟㸪[3. 㓄 ⥺]ࢆཧ↷ࡋ࡚㓄⥺ࢆ⾜ࡗ࡚ࡃࡔࡉ࠸ࠋ

࣭ࢯࢣࢵࢺ╔⬺᫬ࡣ㸪ࢯࢣࢵࢺࡢ㠃࡟ᑐࡋ࡚ᆶ┤࡟ᢤࡁᕪࡋࡋ࡚ࡃࡔࡉ࠸ࠋ

ᆶ┤᪉ྥ௨እࡢຊࡀຍࢃࡿ࡜㸪ᨾ㞀ࡢཎᅉ࡜࡞ࡿሙྜࡀ࠶ࡾࡲࡍࠋ

࣭ྲྀ௜ࡡࡌࡣᙉࡃ⥾ࡵ௜ࡅ㐣ࡂࡿ࡜㸪ᨾ㞀ࡢཎᅉ࡜࡞ࡿሙྜࡀ࠶ࡾࡲࡍࠋ

ճᮏჾࢆࢯࢣࢵࢺ࡟ᤄࡋ㎸ࢇ࡛ࡃࡔࡉ࠸ࠋ

մྲྀ௜ࡡࡌࢆ᫬ィ᪉ྥ࡟ᅇࡋ࡚㸪ࢯࢣࢵࢺ࠿ࡽᮏჾ

ࡀᢤࡅ࡞࠸⛬ᗘ࡟㍍ࡃ⥾ࡵ࡚ࡃࡔࡉ࠸ࠋ

DIN ࣮ࣞࣝ࠿ࡽࡢྲྀࡾእࡋ

ձᮏჾࡢ౪⤥㟁※ࢆษࡗ࡚ࡃࡔࡉ࠸ࠋ

ղᮏჾ๓㠃ࡢྲྀ௜ࡡࡌࢆ⦆ࡵ࡚㸪ᮏჾࢆࢯࢣࢵࢺ

࠿ࡽእࡋ࡚ࡃࡔࡉ࠸ࠋ

ճࢯࢣࢵࢺୗ㒊ࡢࣟࢵࢡࣞࣂ࣮࡟࣐࢖ࢼࢫࢻࣛ࢖

ࣂ࣮ࢆᕪ㎸ࡳ㸪ࣟࢵࢡࣞࣂ࣮ࢆୗࡆ࡞ࡀࡽDIN

࣮ࣞࣝ࠿ࡽእࡋ࡚ࡃࡔࡉ࠸ࠋ(ᅗ2.2-2)

(ᅗ2.2-2)

3. 㓄 ⥺

࣮ࣜࢻ⥺ᅽ╔➃Ꮚ࡟ࡘ࠸࡚

ୗグࡢࡼ࠺࡞㸪M3 ࡢࡡࡌ࡟㐺ྜࡍࡿ⤯⦕ࢫ࣮ࣜࣈ௜ᅽ╔➃Ꮚࢆ౑⏝ࡋ࡚ࡃࡔࡉ࠸ࠋ

⥾௜ࢺࣝࢡࡣ 0.63 N㺃m ࢆᣦᐃࡋ࡚ࡃࡔࡉ࠸ࠋ

Y ᙧᅽ╔➃Ꮚእᙧᅗ(༢఩: mm) ୸ᙧᅽ╔➃Ꮚእᙧᅗ(༢఩: mm)

(ᅗ 3-1)

➃Ꮚ㓄ิࡣ㸪ྛᶵ✀ࡢྲྀᢅㄝ᫂᭩(ヲ⣽∧)ࡲࡓࡣ௙ᵝ᭩ࢆࡈཧ↷ࡃࡔࡉ࠸ࠋ



࠾ၥ࠸ྜࢃࡏ

ᮏჾ࡟ࡘ࠸࡚୙᫂࡞Ⅼࡀࡈࡊ࠸ࡲࡋࡓࡽ㸪኱ኚ࠾ᡭᩘ࡛ࡍࡀᮏჾࡢୗグ㡯┠ࢆࡈ☜

ㄆࡢୖ㸪࠾㈙࠸ୖࡆ࠸ࡓࡔࡁࡲࡋࡓ㈍኎ᗑ࡬࠾ၥ࠸ྜࢃࡏࡃࡔࡉ࠸ࠋ

(౛)

࣭ᙧ ྡ SGFW-F0OO-0-0

࣭ィჾ␒ྕ 154F05000

࡞࠾㸪ືసୖࡢ୙ලྜ࡟ࡘ࠸࡚ࡣ㸪ࡑࡢෆᐜ࡜ࡈ౑⏝≧ែࡢヲ⣽ࢆලయⓗ࡟࠾▱ࡽ

ࡏࡃࡔࡉ࠸ࠋ

ᅽ╔➃Ꮚ ࣓࣮࢝ ᙧ ྡ

Y ᙧ

ࢽࢳࣇ➃Ꮚ TMEV1.25Y-3

᪥ᮏᅽ╔➃Ꮚ VD1.25-B3A

୸ᙧ

ࢽࢳࣇ➃Ꮚ TMEV1.25-3

᪥ᮏᅽ╔➃Ꮚ V1.25-3

ᮏ♫ ࠛ ኱㜰ᗓ⟪㠃ᕷ⯪ሙᮾ  ୎┠  ␒  ྕ

 7(/)$;

85/KWWSZZZVKLQNRWHFKQRVFRMS(PDLOVDOHV#VKLQNRWHFKRVFRMS

኱㜰Ⴀᴗᡤ 7

7(/)$;

ᮾிႠᴗᡤ ࠛ ᮾி㒔୰ኸ༊᪂ᕝ  ୎┠  ␒  ྕ 

 7(/)$;

ྡྂᒇႠᴗᡤ ࠛ ឡ▱┴ྡྂᒇᕷᮾ༊ᮾእᇼ⏫  ␒

&6 ᮾእᇼࣅࣝ  ྕᐊ

 7(/)$;

 ⚄ዉᕝ7(/ ໭㝣7(/

 ᗈᓥ7(/ ⚟ᒸ7(/

Shinko SGFW User manual

Brand: Shinko

Model: SGFW

Type: User manual

This manual is also suitable for

Download PDF

report

Shinko SGFW User manual

This manual is also suitable for

Shinko SGFW User manual

Related papers

Other documents