STIHL HL 94 K (145°) User manual

STIHL HL 94

WARNING

Read Instruction Manual thoroughly

before use and follow all safety

precautions – improper use can

cause serious or fatal injury.

ADVERTENCIA

Antes de usar la máquina lea y siga

todas las precauciones de

seguridad dadas en el manual de

instrucciones – el uso incorrecto

puede causar lesiones graves o

mortales.

Instruction Manual

Manual de instrucciones

Instruction Manual

1 - 41

Manual de instrucciones

42 - 89

Original Instruction ManualPrinted on chlorine-free paper

Printing inks contain vegetable oils, paper can be recycled.

0458-519-8621-C. VA3.K20.

0000008134_005_GB

HL 94, HL 94 K

English

1

with electronic systems.

Contents

Allow only persons who fully understand

this manual to operate your hedge

cutter.

To receive maximum performance and

satisfaction from your STIHL hedge

cutter, it is important that you read,

understand and follow the safety

precautions and the operating and

maintenance instructions in chapter

"Safety Precautions and Working

Techniques" before using your hedge

cutter. For further information you can

go to www.stihlusa.com.

Contact your STIHL dealer or the STIHL

distributor for your area if you do not

understand any of the instructions in this

manual.

WARNING

Because a hedge cutter is a high-speed

cutting tool some special safety

precautions must be observed to reduce

the risk of personal injury. Careless or

improper use may cause serious or even

fatal injury.

Guide to Using this Manual 2

Safety Precautions and Working

Techniques 2

Using the Unit 13

Approved Power Tool Attachments 15

Assembling the Unit 16

Fuel 17

Fueling 18

Adjusting the Cutter Bar 20

Fitting the Harness 21

Starting / Stopping the Engine 22

Operating Instructions 25

Cleaning the Air Filter 25

Engine Management 26

Adjusting the Carburetor 26

Spark Plug 26

Lubricating the Gearbox 28

Sharpening Instructions 29

Storing the Machine 29

Inspection and Maintenance by

User 29

Inspections and Maintenance by

Dealer 30

Maintenance and Care 31

Main Parts 33

Specifications 35

Maintenance and Repairs 36

Disposal 36

Limited Warranty 36

STIHL Incorporated Federal

Emission Control Warranty

Statement 37

STIHL Incorporated California

Exhaust and Evaporative

Emissions Control Warranty

Statement 39

Trademarks 41

HL 94, HL 94 K

English

2

Pictograms

The meanings of the pictograms

attached to or embossed on the

machine are explained in this manual.

Depending on the model concerned, the

following pictograms may be on your

machine.

Symbols in Text

Many operating and safety instructions

are supported by illustrations.

The individual steps or procedures

described in the manual may be shown

in different ways:

N A bullet indicates a step or

procedure.

A description of a step or procedure that

refers directly to an illustration may

contain item numbers that appear in the

illustration. For example:

N Remove the screw (1)

N Pull the spark arresting screen (2)

upwards out of the muffler

In addition to the operating instructions,

this manual may contain paragraphs

that require your special attention. Such

paragraphs are indicated with the

symbols and signal words described

below:

DANGER

Indicates a hazardous situation that, if

not avoided, will result in death or

serious injury.

WARNING

Indicates a hazardous situation that, if

not avoided, could result in death or

serious injury.

NOTICE

Indicates a risk of property damage,

including damage to the machine or its

individual components.

Engineering Improvements

STIHL’s philosophy is to continually

improve all of its products. As a result,

engineering changes and improvements

are made from time to time. Therefore,

some changes, modifications and

improvements may not be covered in

this manual. If the operating

characteristics or the appearance of

your machine differs from those

described in this manual, please contact

your STIHL dealer or the STIHL

distributor for your area for assistance.

Have your STIHL dealer show you how

to operate your power tool. Observe all

applicable local safety regulations,

standards and ordinances.

WARNING

Do not lend or rent your power tool

without the instruction manual. Be sure

that anyone using it understands the

information contained in this manual.

WARNING

The use of this machine may be

hazardous. If the cutting tool comes in

contact with your body, it will cut you.

Use your hedge trimmer only for cutting

hedges, shrubs, scrub, bushes and

similar material.

Guide to Using this Manual

Fuel tank for gasoline

and engine oil mixture

Press to operate manual

fuel pump

Filler hole for gear

lubricant

Safety Precautions and

Working Techniques

Because a hedge trim

-

mer is a high-speed, fast-

cutting power tool with

sharp cutting blades,

special safety precau

-

tions must be observed to

reduce the risk of per

-

sonal injury.

It is important that you

read, fully understand

and observe the following

safety precautions and

warnings. Read the

instruction manual and

the safety precautions

periodically. Careless or

improper use may cause

serious or fatal injury.

HL 94, HL 94 K

English

3

WARNING

Do not use it for other purposes, since

misuse may result in personal injury or

property damage, including damage to

the machine.

WARNING

Minors should never be allowed to use

this power tool. Bystanders, especially

children, and animals should not be

allowed in the area where it is in use.

WARNING

To reduce the risk of injury to bystanders

and damage to property, never let your

power tool run unattended. When it is

not in use (e.g. during a work break),

shut it off and make sure that

unauthorized persons do not use it.

Most of these safety precautions and

warnings apply to the use of all STIHL

hedge trimmers. Different models may

have different parts and controls. See

the appropriate section of your

instruction manual for a description of

the controls and the function of the parts

of your model.

Safe use of a hedge trimmer involves

1. the operator

2. the power tool

3. the use of the power tool.

THE OPERATOR

Physical Condition

You must be in good physical condition

and mental health and not under the

influence of any substance (drugs,

alcohol, etc.) which might impair vision,

dexterity or judgment. Do not operate

this machine when you are fatigued.

WARNING

Be alert – if you get tired, take a break.

Tiredness may result in loss of control.

Working with any power tool can be

strenuous. If you have any condition that

might be aggravated by strenuous work,

check with your doctor before operating

this machine.

WARNING

Prolonged use of a power tool (or other

machines) exposing the operator to

vibrations may produce whitefinger

disease (Raynaud's phenomenon) or

carpal tunnel syndrome.

These conditions reduce the hand's

ability to feel and regulate temperature,

produce numbness and burning

sensations and may cause nerve and

circulation damage and tissue necrosis.

All factors which contribute to white-

finger disease are not known, but cold

weather, smoking and diseases or

physical conditions that affect blood

vessels and blood transport, as well as

high vibration levels and long periods of

exposure to vibration are mentioned as

factors in the development of whitefinger

disease. In order to reduce the risk of

whitefinger disease and carpal tunnel

syndrome, please note the following:

Most STIHL power tools are available

with an anti-vibration ("AV") system

designed to reduce the transmission of

vibrations created by the machine to the

operator's hands. An AV system is

recommended for those persons using

power tools on a regular or sustained

basis.

– Wear gloves and keep your hands

warm.

– Keep the AV system well

maintained. A power tool with loose

components or with damaged or

worn AV elements will tend to have

higher vibration levels.

– Maintain a firm grip at all times, but

do not squeeze the handles with

constant, excessive pressure. Take

frequent breaks.

All the above-mentioned precautions do

not guarantee that you will not sustain

whitefinger disease or carpal tunnel

syndrome. Therefore, continual and

regular users should closely monitor the

condition of their hands and fingers. If

any of the above symptoms appear,

seek medical advice immediately.

WARNING

The ignition system of the STIHL unit

produces an electromagnetic field of a

very low intensity. This field may

interfere with some pacemakers. To

reduce the risk of serious or fatal injury,

persons with a pacemaker should

consult their physician and the

pacemaker manufacturer before

operating this tool.

HL 94, HL 94 K

English

4

Proper Clothing

WARNING

To reduce the risk of injury, the operator

should wear proper protective apparel.

WARNING

Wear an approved safety hard hat to

reduce the risk of injury to your head

when there is a danger of head injuries.

Power tool noise may damage your

hearing. Wear sound barriers (ear plugs

or ear mufflers) to protect your hearing.

Continual and regular users should have

their hearing checked regularly.

Be particularly alert and cautious when

wearing hearing protection because

your ability to hear warnings (shouts,

alarms, etc.) is restricted.

THE POWER TOOL

For illustrations and definitions of the

power tool parts see the chapter on

"Main Parts and Controls".

WARNING

Never modify this power tool in any way.

Only attachments supplied by STIHL or

expressly approved by STIHL for use

with the specific STIHL model are

authorized. Although certain

unauthorized attachments are useable

with STIHL power tools, their use may,

in fact, be extremely dangerous.

If this tool is subjected to unusually high

loads for which it was not designed (e.g.

heavy impact or a fall), always check

that it is in good condition before

continuing work. Check in particular that

the fuel system is tight (no leaks) and

that the controls and safety devices are

working properly. Do not continue

operating this machine if it is damaged.

In case of doubt, have it checked by your

STIHL servicing dealer.

THE USE OF THE POWER TOOL

Transporting the Power Tool

WARNING

To reduce the risk of injury from blade

contact, never carry or transport your

power tool with the cutter blades

moving.

To reduce the risk of

injury to your eyes never

operate your power tool

unless wearing goggles

or properly fitted protec

-

tive glasses with

adequate top and side

protection complying with

ANSI Z87 "+" (or your

applicable national stand

-

ard). To reduce the risk of

injury to your face STIHL

recommends that you

also wear a face shield or

face screen over your

goggles or protective

glasses.

Always wear heavy duty

work gloves (e.g. made of

leather or other wear

resistant material) when

handling the machine

and the cutting tool.

Heavy-duty, nonslip

gloves improve your grip

and help to protect your

hands.

Clothing must be sturdy

and snug-fitting, but allow

complete freedom of

movement. Wear long

pants made of heavy

material to help protect

your legs. Do not wear

shorts, sandals or go

barefoot.

Avoid loose-fitting jack

-

ets, scarfs, neckties,

jewelry, flared or cuffed

pants, unconfined long

hair or anything that

could become caught on

branches, brush or the

moving parts of the unit.

Secure hair so it is above

shoulder level.

Good footing is very

important. Wear sturdy

boots with nonslip soles.

Steel-toed safety boots

are recommended.

HL 94, HL 94 K

English

5

It may be carried only in a horizontal

position. Grip the shaft in a manner that

the machine is balanced horizontally.

Keep the hot muffler away from your

body and the cutting attachment behind

you.

WARNING

Always switch off the engine and fit the

scabbard over the cutter blades before

transporting the power tool over long

distances. When transporting it in a

vehicle, properly secure it to prevent

turnover, fuel spillage and damage to

the unit.

On machines with an adjustable cutter

bar: Make sure the cutter bar is secured

in position. See chapter in instruction

manual entitled "Adjusting Cutter Bar

Angle." On machines with a transport

position: Move cutter bar to transport

position and secure.

Fuel

Your STIHL power tool uses an oil-

gasoline mixture for fuel (see the "Fuel"

chapter in this instruction manual).

WARNING

Fueling Instructions

WARNING

To reduce the risk of fire and serious

personal injury, always place the power

tool on the ground before attempting to

fuel the machine.

WARNING

Pick a Safe Location

To reduce the risk of fire and explosion,

fuel your power tool in a well-ventillated

area, outdoors away from flames, pilot

lights, heaters, electric motors, and

other sources of ignition. Vapors can be

ignited by a spark or flame many feet

away. Select bare ground for fueling and

move at least 10 feet (3 m) from the

fueling spot before starting the engine.

Wipe off any spilled fuel before starting

your power tool. Take care not to get fuel

on your clothing. If this happens, change

your clothing immediately.

Allow the Power Tool to Cool Before

Removing the Fuel Cap

WARNING

Gasoline vapor pressure may build up

inside the fuel tank. The amount of

pressure depends on a number of

factors such as the fuel used, altitude

and temperature. To reduce the risk of

burns and other personal injury from

escaping gas, vapor and fumes, always

shut off the engine and allow it to cool

before removing the fuel cap.

The engine is air cooled. When it is shut

off, cooling air is no longer drawn across

the cylinder and engine temperatures

will rise for several minutes before

starting to cool. In hot environments,

cooling will take longer. To reduce the

risk of burns and other personal injury

To reduce the risk of burn

injury, do not touch hot

parts of the machine and

the gear housing when

they are hot.

0000096960_001

Gasoline is an extremely

flammable fuel. If spilled

and ignited by a spark or

other ignition source, it

can cause fire and seri

-

ous burn injury or

property damage. Use

extreme caution when

handling gasoline or fuel

mix. Do not smoke or

bring any fire or flame

near the fuel or the power

tool. Note that combus

-

tible fuel vapor may

escape from the fuel

system.

HL 94, HL 94 K

English

6

from escaping gas, vapor and fumes,

allow the power tool to cool. If you need

to refuel before completing a job, turn off

the machine and allow the engine to cool

before opening the fuel tank.

Fuel Spraying or “Geysering”

WARNING

Removing the cap on a pressurized fuel

tank can result in gasoline, vapors and

fumes being forcefully sprayed out from

the fuel tank in all directions. The

escaping gasoline, vapors or fumes can

cause serious personal injury, including

fire and burn injury, or property damage.

Sometimes also referred to as "fuel

geysering," fuel spraying is an expulsion

of fuel, vapors and fumes which can

occur in hot conditions, or when the

engine is hot, and the tank is opened

without allowing the power tool to cool

adequately. It is more likely to occur

when the fuel tank is half full or more.

Pressure is caused by fuel and heat and

can occur even if the engine has not

been running. When gasoline in the fuel

tank is heated (by ambient

temperatures, heat from the engine, or

other sources), vapor pressure will

increase inside the fuel tank.

Some blends of gasoline, particularly

those designed for use in winter, are

more volatile and may cause tanks to

pressurize more quickly or create

greater pressure. At higher altitudes,

fuel tank pressurization is more likely.

How to Avoid Fuel Spraying

Removing the fuel cap on a pressurized

tank can result in gasoline, vapors and

fumes being forcefully sprayed out from

the fuel tank in all directions. To reduce

the risk of burns, serious injuries or

property damage from fuel spraying:

– Follow the fueling instructions in this

chapter.

– Always assume your fuel tank is

pressurized.

– Allow the power tool to cool before

removing the fuel cap.

– In hot environments, cooling will

take longer.

– The engine is air cooled. When it is

shut off, cooling air is no longer

drawn across the cylinder and the

engine temperature will rise for

several minutes before starting to

cool.

After the power tool has cooled

appropriately, follow the safety

instructions in this chapter for removing

the cap.

Never remove the fuel filler cap by

turning it directly to the open position.

First check for residual pressure in the

tank by slowly turning the cap

approximately 1/2 turn counter-

clockwise. The cap should be held in

place by the threads while allowing

residual vapor/pressure to be relieved.

Once the fumes or vapor have been

relieved, turn the cap further until it can

be removed from the tank opening.

Use only good quality fuel that is

appropriate for the season (summer v.

winter blends). Some blends of

gasoline, particularly winter blends, are

more volatile and can contribute to fuel

spraying.

Removing the Threaded Fuel Filler Cap

WARNING

After allowing the power tool to cool,

remove the fuel filler cap slowly and

carefully to allow any remaining

pressure build-up in the tank to release:

– While maintaining steady,

downward pressure, slowly turn the

cap approximately 1/2 turn counter-

clockwise.

– If any significant venting occurs,

immediately re-seal the tank by

turning the cap clockwise to the

closed position. Allow the power

tool to cool further before

attempting to open the tank.

– Turn the cap to the open position

only after the contents of the tank

are no longer under pressure.

– Never remove the cap by turning it

directly to the open position. First

allow the power tool to cool

adequately and then release any

residual pressure by slowly turning it

approximately 1/2 turn counter-

clockwise.

– Never attempt to remove the cap

while the engine is still hot or

running.

HL 94, HL 94 K

English

7

Installing the Threaded Fuel Filler Cap

WARNING

Damaged or Broken Cap

If your fuel cap does not tighten properly,

it may be damaged or broken. Stop

using the power tool and take it to your

authorized STIHL dealer for repair.

Vapor Lock

WARNING

Vapor lock occurs when fuel in the fuel

line or carburetor vaporizes, causing

bubbles to block the free flow of liquid

fuel into the carburetor. Vapor lock

cannot be relieved or affected by

opening the fuel tank. Removing the fuel

filler cap without first allowing the power

tool to cool adequately can result in fuel

spraying. Always follow the instructions

in this section when removing the fuel

cap.

To relieve vapor lock:

– Press the manual fuel pump bulb at

least 20 to 30 times – even if the

bulb is already filled with fuel – to

clear the vapor and send liquid fuel

into the carburetor. Then start the

power tool. For specific starting

instructions, see the appropriate

section of your instruction manual.

– If the manual fuel pump bulb will not

be filled, place the Choke Knob to

the cold start position g and pull

the starter cord until the engine

runs. If the engine does not fire after

10 pulls in the cold start

position g, place the Choke Knob

to the run position F and start the

engine in the run position F.

– If your power tool will not restart, or

if vapor lock occurs again, the

power tool is being used in

conditions too extreme for the fuel

being used. Discontinue use and let

the engine cool completely before

attempting to start the power tool.

Before Operation

WARNING

Always check your power tool for proper

condition and operation before starting,

particularly the throttle trigger, throttle

trigger lockout, throttle set wheel, stop

switch and cutting tool. The throttle

trigger must move freely and always

spring back to the idle position. Never

attempt to modify the controls or safety

devices.

WARNING

Check fuel system for leaks, especially

the visible parts, e.g., filler cap, hose

connections, manual fuel pump (only for

power tools equipped with a manual fuel

pump). Do not start the engine if there

are leaks or damage – risk of fire. Have

the power tool repaired by a STIHL

servicing dealer before using it.

WARNING

Never operate your power tool if it is

damaged, improperly adjusted or

maintained, or not completely and

securely assembled.

WARNING

Check that the spark plug boot is

securely mounted on the spark plug – a

loose boot may cause arcing that could

ignite combustible fumes and cause a

fire.

Keep the handles clean and dry at all

times; it is particularly important to keep

them free of moisture, pitch, oil, fuel mix,

grease or resin in order for you to

maintain a firm grip and properly control

your power tool.

WARNING

The cutting tool must be properly

tightened and in safe operating

condition. Inspect for loose parts (nuts,

screws, etc.) and for cracked, bent,

warped or damaged blades. Regularly

check the condition and tightness of the

cutter blades – with the engine stopped!

Replace damaged cutter blades before

using the power tool. Always keep

blades sharp.

Unit vibrations can cause

an improperly tightened

fuel filler cap to loosen or

come off and spill quanti

-

ties of fuel. To reduce the

risk of fuel spillage and

fire, tighten the fuel filler

cap by hand with as

much force as possible.

HL 94, HL 94 K

English

8

STIHL recommends that you always

spray the cutter blades with STIHL resin

solvent before starting work – with the

engine stopped! You can obtain this

protective spray from your dealer. Apply

generously.

Adjust carrying harness and hand grip to

suit your size before starting work.

For specific starting instructions, see the

appropriate section of your instruction

manual.

Starting

On machines with an adjustable cutter

bar: Secure the cutter bar in the starting

position as described in the chapter

"Starting/Stopping the Engine." If this

starting position is not the desired

cutting position, you will then need to

carefully adjust the machine to the

desired position once the engine has

returned to idle and the blades are no

longer moving.

On machines with a defined transport

position (cutter bar folded against the

drive tube): Never start the machine in

the transport position, since the blades

are not engaged in that position and you

therefore cannot visually check to see

that they will be stopped at idle when

you start to adjust the cutter bar to the

desired cutting position (where the

blades are engaged).

Start the engine at least 10 feet (3 m)

from the fueling spot, outdoors only.

For specific starting instructions, see the

appropriate section of your manual.

Place the power tool on firm ground or

other solid surface in an open area.

Maintain good balance and secure

footing.

WARNING

To reduce the risk of injury from blade

contact, be absolutely sure that the

cutting tool is clear of you and all other

obstructions and objects, including the

ground, because when the engine starts

at starting-throttle or with the choke knob

engaged, engine speed will be fast

enough for the clutch to engage and

move the blades on the cutting tool.

Once the engine has started,

immediately blip the throttle trigger,

which should release the starting throttle

and allow the engine to slow down to

idle.

With the engine running only at idle,

attach the power tool to the spring hook

of your harness (see appropriate

chapter of this manual).

WARNING

Your power tool is a one-person

machine. Do not allow other persons in

the general work area, even when

starting.

WARNING

To reduce the risk of injury from loss of

control, do not attempt to "drop start"

your power tool.

WARNING

When you pull the starter grip, do not

wrap the starter rope around your hand.

Do not let the grip snap back, but guide

the starter rope to rewind it properly.

Failure to follow this procedure may

result in injury to your hand or fingers

and may damage the starter

mechanism.

Important Adjustments

WARNING

To reduce the risk of personal injury

from loss of control or contact with the

running cutting tool, do not use your unit

with incorrect idle adjustment. At correct

idle speed, the cutting tool should not

move. For directions on how to adjust

idle speed, see the appropriate section

of your instruction manual.

0000096961_001

HL 94, HL 94 K

English

9

If you cannot set the correct idle speed,

have your STIHL dealer check your

power tool and make proper

adjustments and repairs.

WARNING

This unit is equipped with an ignition

system that is normally in operational

readiness. After the stop switch is used

to stop the engine, it automatically

springs back to the "on" position. If the

engine is warm, it may be possible to

start it by simply pulling the starter rope,

with no further adjustments. To reduce

the risk of injury, be particularly alert to

keep children away from the unit.

During Operation

Holding and Controlling the Power Tool

Always hold the unit firmly with both

hands on the handles while you are

working.

Models with loop handle

Right hand on control handle, left hand

on loop handle on drive tube, even if you

are left-handed. Wrap your fingers and

thumbs around the handles.

Models with handle hose

Right hand on control handle, left hand

on handle hose on drive tube, even if

you are left-handed. Wrap your fingers

and thumbs around the handles.

WARNING

Do not overreach. Keep proper footing

and balance at all times. Special care

must be taken in slippery conditions (wet

ground, snow) and in difficult, overgrown

terrain. Watch for hidden obstacles such

as tree stumps, roots and ditches to

avoid stumbling. For better footing, clear

away fallen branches, scrub and

cuttings. Be extremely cautious when

working on slopes or uneven ground.

WARNING

To reduce the risk of injury from loss of

control, never work on a ladder, in a tree

or any other insecure support. Never

hold the machine above shoulder

height.

Working Conditions

Operate and start your power tool only

outdoors in a well ventilated area.

Operate it under good visibility and

daylight conditions only. Work carefully.

WARNING

0000-GXX-1677-A0

Never attempt to operate

your power tool with one

hand. Loss of control of

the power tool resulting in

serious or fatal injury may

result. To reduce the risk

of cut injuries, keep

hands and feet away

from the cutting tool.

Never touch a moving

cutting tool with your

hand or any other part of

your body.

0000096958_001

As soon as the engine is

running, this product gen

-

erates toxic exhaust

fumes containing chemi

-

cals, such as unburned

hydrocarbons (including

benzene) and carbon

monoxide, that are

known to cause respira

-

tory problems, cancer,

birth defects, or other

reproductive harm. Some

of the gases (e.g. carbon

monoxide) may be color

-

less and odorless. To

reduce the risk of serious

or fatal injury/illness from

inhaling toxic fumes,

never run the machine

indoors or in poorly venti

-

lated locations.

HL 94, HL 94 K

English

10

WARNING

If the vegetation being cut or the

surrounding ground is coated with a

chemical substance (such as an active

pesticide or herbicide), read and follow

the instructions and warnings that

accompanied the substance at issue.

WARNING

Inhalation of certain dusts, especially

organic dusts such as mold or pollen,

can cause susceptible persons to have

an allergic or asthmatic reaction.

Substantial or repeated inhalation of

dust and other airborne contaminants, in

particular those with a smaller particle

size, may cause respiratory or other

illnesses. Control dust at the source

where possible. Use good work

practices, such as operating the unit so

that the wind or operating process

directs any dust raised by the power tool

away from the operator. Follow the

recommendations of

EPA/OSHA/NIOSH and occupational

and trade associations with respect to

dust ("particulate matter"). When the

inhalation of dust cannot be

substantially controlled, i.e., kept at or

near the ambient (background) level, the

operator and any bystanders should

wear a respirator approved by

NIOSH/MSHA for the type of dust

encountered.

Operating Instructions

WARNING

Do not operate your power tool using the

starting throttle lock or with the choke

knob engaged, as you do not have

control of the engine speed.

In the event of an emergency, switch off

the engine immediately – press the stop

switch.

WARNING

The cutter blades continue to move for a

short period after the throttle trigger is

released (flywheel effect).

Accelerating the engine while the blades

are blocked increases the load and will

cause the clutch to slip continuously.

This may result in overheating and

damage to important components (e.g.

clutch, polymer housing components) –

which can then increase the risk of injury

from the blades moving while the engine

is idling.

WARNING

On units with an adjustable cutter bar:

To reduce the risk of injury, never touch

the blades while making adjustments.

The power tool

has a large range.

In order to reduce

the risk of

personal or even

fatal injury to

bystanders from falling objects or

inadvertent contact with the moving

cutter blades of your power tool always

keep bystanders at least 17 feet (5 m)

away when the power tool is running.

Stop the engine and cutting tool

immediately if you are approached.

WARNING

Before you start work, examine the

hedge area for stones, fence wire, metal

or other solid objects which could

damage the cutter blades.

Take particular care when cutting

hedges next to or against wire fences.

Do not touch the wire with the cutting

blades. When working close to the

ground, make sure that no sand, grit or

stones get between the cutter blades.

Striking solid foreign objects such as

stones, fence wire or metal could

damage the cutting attachment and may

cause blades to crack, chip or break.

STIHL does not recommend the use of

your power tool when cutting in areas

where the blades could contact such

objects.

WARNING

Observe the cutting blades at all times –

do not cut any areas of the hedge that

you cannot see. When cutting the top of

a taller hedge, check the other side of

the hedge frequently for bystanders,

animals and obstructions.

5m (17ft)

HL 94, HL 94 K

English

11

DANGER

WARNING

If the cutting tool becomes clogged or

stuck, always turn off the engine and

make sure the cutting tool has stopped

before cleaning. Grass, weeds, etc.

should be cleaned off the cutting tool at

regular intervals.

Check the cutting blades at regular short

intervals during operation, or

immediately if there is a noticeable

change in cutting behavior:

– Shut off the engine.

– Wait until the cutting blades have

come to a complete standstill.

– Check condition and tightness, look

for cracks.

– Check sharpness.

– Replace damaged or dull cutting

tools immediately, even if they have

only superficial cracks.

WARNING

Never modify your muffler. Any

modification could cause an increase in

heat radiation, sparks or sound level,

thereby increasing the risk of fire, burn

injury or hearing loss. You may also

permanently damage the engine. Have

your muffler serviced and repaired by

your STIHL servicing dealer only.

WARNING

The muffler and other parts of the engine

(e.g. fins of the cylinder, spark plug)

become hot during operation and remain

hot for a while after stopping the engine.

To reduce risk of burns, do not touch the

muffler and other parts while they are

hot. Keep the area around the muffler

clean. Remove excess lubricant and all

debris such as pine needles, branches

or leaves. Let the engine cool down

sitting on concrete, metal, bare ground

or solid wood (e.g. the trunk of a felled

tree) away from any combustible

substances.

WARNING

An improperly mounted or damaged

cylinder housing or a

damaged/deformed muffler shell may

interfere with the cooling process of the

muffler. To reduce the risk of fire or burn

injury, do not continue work with a

damaged or improperly mounted

cylinder housing or a

damaged/deformed muffler shell.

Your muffler is furnished with a spark

arresting screen designed to reduce the

risk of fire from the emission of hot

particles. Never operate your unit with a

missing or damaged spark arresting

screen. If your gas/oil mix ratio is correct

(i.e., not too rich), this screen will

normally stay clean as a result of the

heat from the muffler and need no

service or maintenance. If you

experience loss of performance and you

suspect a clogged screen, have your

muffler maintained by a STIHL servicing

dealer. Some state or federal laws or

regulations may require a properly

maintained spark arrestor for certain

uses. See the "Maintenance, Repair and

Storing" section of these Safety

Precautions. Remember that the risk of

a brush or forest fire is greater in hot or

dry conditions.

Your power tool is not

insulated against electric

shock. To reduce the risk

of electrocution, never

operate this power tool in

the vicinity of any wires or

cables (power, etc.)

which may be carrying

electric current.

The gearbox becomes

hot during operation. To

reduce the risk of burn

injury, do not touch the

gear housing when it is

hot.

HL 94, HL 94 K

English

12

WARNING

After Finishing Work

Always clean dust and dirt off the

machine – do not use any grease

solvents for this purpose.

Spray the blades with STIHL resin

solvent. Start and run the engine briefly

so that the solvent is evenly distributed.

MAINTENANCE, REPAIR AND

STORING

Maintenance, replacement, or repair of

the emission control devices and

systems may be performed by any

nonroad engine repair establishment or

individual. However, if you make a

warranty claim for a component which

has not been serviced or maintained

properly, STIHL may deny coverage.

WARNING

Use only identical STIHL replacement

parts for maintenance and repair. Use of

non-STIHL parts may cause serious or

fatal injury.

Strictly follow the maintenance and

repair instructions in the appropriate

section of your instruction manual.

Please also refer to the maintenance

chart in this manual.

WARNING

Always stop the engine and make sure

that the cutting blades are stopped

before doing any maintenance or repair

work or cleaning the power tool. Do not

attempt any maintenance or repair work

not described in your instruction manual.

Have such work performed by your

STIHL servicing dealer only.

Wear gloves when handling or

performing maintenance on blades.

WARNING

Use the specified spark plug and make

sure it and the ignition lead are always

clean and in good condition. Always

press spark plug boot snugly onto spark

plug terminal of the proper size. (Note: If

terminal has detachable SAE adapter

nut, it must be securely attached.) A

loose connection between spark plug

terminal and the ignition wire connector

in the boot may create arcing that could

ignite combustible fumes and cause a

fire.

WARNING

Never test the ignition system with the

ignition wire boot removed from the

spark plug or with a removed spark plug,

since uncontained sparking may cause

a fire.

WARNING

Do not operate your power tool if the

muffler is damaged, missing or modified.

An improperly maintained muffler will

increase the risk of fire and hearing loss.

Your muffler is equipped with a spark-

arresting screen to reduce the risk of

fire; never operate your power tool if the

screen is missing, damaged or clogged.

Remember that the risk of a brush or

forest fire is greater in hot or dry

weather.

In California, it is a violation of § 4442 or

§ 4443 of the Public Resources Code to

use or operate gasoline-powered tools

on forest-covered, brush-covered or

grass-covered land unless the engine’s

exhaust system is equipped with a

complying spark arrester that is

maintained in effective working order.

The owner/operator of this product is

responsible for properly maintaining the

spark arrester. Other states or

governmental entities/agencies, such as

the U.S. Forest Service, may have

similar requirements. Contact your local

fire agency or forest service for the laws

or regulations relating to fire protection

requirements.

Some STIHL power tools

are equipped with a cata

-

lytic converter, which is

designed to reduce the

exhaust emissions of the

engine by a chemical pro

-

cess in the muffler. Due

to this process, the muf

-

fler does not cool down

as rapidly as conven

-

tional mufflers when the

engine returns to idle or

is shut off. To reduce the

risk of fire and burn inju

-

ries when using a

catalytic converter,

always set your power

tool down in the upright

position and never locate

it where the muffler is

near dry brush, grass,

wood chips or other com

-

bustible materials while it

is still hot.

HL 94, HL 94 K

English

13

WARNING

Never repair damaged cutting attach-

ments by welding, straightening or

modifying the shape. This may cause

parts of the cutting blades to come off

and result in serious or fatal injuries.

Keep the cutting blades sharp. Tighten

all nuts, bolts and screws, except the

carburetor adjustment screws, after

each use.

Do not clean your machine with a

pressure washer. The solid jet of water

may damage parts of the machine.

Store the power tool in a dry and high or

locked location out of reach of children.

Before storing for longer than a few

days, always empty the fuel tank. See

chapter "Storing the machine" in this

manual.

Cutting Season

Observe country-specific or municipal

rules and regulations for cutting hedges.

Do not use your hedge trimmer during

rest periods customary in the

neighborhood.

Cutting Sequence

If a radical cut is necessary, cut a little at

a time in several stages.

Use lopping shears to cut out thick

branches first.

Cut the sides of the hedge first, then the

top.

Disposal

Do not throw cuttings into the garbage

can – they can be composted.

Preparations

N Model with adjustable cutter bar:

Set the cutter bar to the straight (0°)

position.

N Remove the blade scabbard.

N Start the engine.

N If you use a harness: Put on the

harness and attach it to the

machine.

Working Technique

Horizontal Cut (with cutter bar at an

angle)

Cutting close to the ground from a

standing position, e.g. low shrubs.

Swing the cutter bar up and down as you

move along the hedge – use both sides

of the cutting blades, do not rest the

cutter bar on the ground.

WARNING

The K version (HL 94 K) is not approved

for cutting close to the ground.

Using the Unit

388BA029 KN

HL 94, HL 94 K

English

14

Vertical Cut (with cutter bar at an angle)

Cutting without standing directly next to

the hedge, e.g. flowerbed between

operator and hedge.

Swing the cutter bar up and down in an

arc as you move along the hedge – use

both sides of the cutting blades.

Vertical Cut (with straight cutter bar)

Extra long reach without the need for

other aids.

Swing the cutter bar up and down in an

arc as you move along the hedge – use

both sides of the cutting blades.

Overhead Cut (with cutter bar at an

angle)

Hold the hedge trimmer vertically and

swing it in an arc to make maximum use

of its reach.

WARNING

Any working position above head height

is tiring. To minimize the risk of

accidents, work in such positions for

short periods only. Set the adjustable

cutter bar to the most suitable angle so

that the unit can be held in a lower, less

tiring position while still providing

adequate reach.

388BA030 KN

389BA050 KN

388BA031 KN

HL 94, HL 94 K

English

15

Horizontal Cut (with straight cutter bar)

Hold the cutter bar at an angle of 0° to

10° as you swing the hedge trimmer

horizontally.

Swing the cutter bar in an arc towards

the outside of the hedge so that the

cuttings are swept to the ground.

Recommendation: Only cut hedges that

are no more than chest high.

The following STIHL attachments may

be used with the basic power tool:

388BA032 KN

388BA033 KN

Approved Power Tool

Attachments

Attachment

1)

Loop handle required on versions

with long drive tube (HL 94)

2)

Not approved for versions with

short drive tube (HL 94 K)

3)

Loop handle required

Application

HL 0°, 500 mm

1)

Long reach hedge

trimmer

HL 0°, 600 mm

1)

Long reach hedge

trimmer

HL 145°,

500 mm

1)

Long reach hedge

trimmer

HL 145°,

600 mm

1)

Long reach hedge

trimmer

HT

2)

Pole saw

BF

2) 3)

Cultivator with pick

tines

KB (4601)

2) 3)

Bristle brush

KW (4601)

2) 3)

PowerSweep

HL 94, HL 94 K

English

16

Mounting the Loop Handle (HL 94)

Loop handle is required on versions with

long drive tube (HL 94).

N Place the clamp (1) in the loop

handle (2) and position them both

against the drive tube (5) between

the carrying ring (3) and handle

hose (4).

N Position the clamp (6) against the

shaft.

N Line up the holes.

N Insert the screws (7) with

washers (8).

N Fit the square nuts (9) and screws.

N Align the loop handle (2) and move

it to the most comfortable position

(recommended: about 20 cm/8 in).

N Tighten down the screws firmly.

Mounting the Gearbox

N Loosen the clamp screws (10).

N Push the gearbox (11) onto the

drive tube (5), turn the gearbox (11)

back and forth as necessary.

Assembling the Unit

7

8

2

1

6

7

8

9

3

5

4

0000-GXX-1679-A0

2

A

0000-GXX-1680-A0

11

10

5

0000-GXX-1681-A0

HL 94, HL 94 K

English

17

Once the end of the drive tube is

inserted beyond the slot in the

clamp (12):

N Push the gearbox (11) fully home as

far as stop.

N Tighten down the clamp screws

moderately.

N Line up the gearbox (11) with the

powerhead.

N Tighten down the clamp screws

firmly.

This engine is certified to operate on

unleaded gasoline and the STIHL two-

stroke engine oil at a mix ratio of 50:1.

Your engine requires a mixture of high-

quality gasoline and two-stroke air

cooled engine oil.

Use mid-grade unleaded gasoline with a

minimum octane rating of 89 ((R+M)/2)

and no more than 10% ethanol content.

NOTICE

Fuel with an octane rating below 89 may

increase engine temperatures. This, in

turn, increases the risk of piston seizure

and damage to the engine.

The chemical composition of the fuel is

also important. Some fuel additives not

only detrimentally affect elastomers

(carburetor diaphragms, oil seals, fuel

lines, etc.), but magnesium castings and

catalytic converters as well. This could

cause running problems or damage the

engine. For this reason STIHL

recommends that you use only quality

unleaded gasoline!

NOTICE

Gasoline with an ethanol content of

more than 10% can cause running

problems and major damage in engines

and should not be used.

For further details, see

www.STIHLusa.com/ethanol

The ethanol content in gasoline affects

engine speed – it may be necessary to

readjust the carburetor if you use fuels

with various ethanol contents.

WARNING

To reduce the risk of personal injury

from loss of control and/or contact with

the running cutting tool, do not use your

unit with an incorrect idle adjustment. At

correct idle speed, the cutting tool

should not move.

If your machine’s idle speed is

incorrectly adjusted, have your

authorized STIHL servicing dealer

check your machine and make the

proper adjustments and repairs.

The idle speed and maximum speed of

the engine change if you switch from a

fuel with a certain ethanol content to a

fuel with a much higher or lower ethanol

content.

This problem can be avoided by always

using fuel with the same ethanol

content.

To ensure the maximum performance of

your STIHL engine, use a high quality 2-

cycle engine oil. To help your engine run

cleaner and reduce harmful carbon

deposits, STIHL recommends using

STIHL HP Ultra 2-cycle engine oil or ask

your dealer for an equivalent fully

synthetic 2-cycle engine oil.

To meet the requirements of EPA and

CARB we recommend to use STIHL HP

Ultra oil.

STIHL MotoMix

STIHL recommends the use of STIHL

MotoMix. STIHL MotoMix has a high

octane rating and ensures that you

always use the right gasoline/oil mix

ratio.

11

12

0000-GXX-1682-A0

Fuel

HL 94, HL 94 K

English

18

STIHL MotoMix uses STIHL HP Ultra

two-stroke engine oil suited for high

performance engines.

For further details, see

www.STIHLusa.com/ethanol

If not using MotoMix, use only STIHL

two-stroke engine oil or equivalent high-

quality two-stroke engine oils that are

designed for use in air cooled two-cycle

engines.

The use of non-seasonal gasoline

blends may increase the potential for

pressure to build in the fuel tank during

operation. For example, using a winter

blend during the summer will increase

pressure in the fuel tank. Always use

gasoline blends appropriate to the

season, altitude and other

environmental factors.

Do not use NMMA or TCW rated (two-

stroke water cooled) mix oils or other

mix oils that state they are for use in both

water cooled and air cooled engines

(e.g., outboard motors, snowmobiles,

chain saws, mopeds, etc.).

WARNING

Take care when handling gasoline.

Avoid direct contact with the skin and

avoid inhaling fuel vapor. When filling at

the pump, first remove the container

from your vehicle and place the

container on the ground before filling. To

reduce the risk of sparks from static

discharge and resulting fire and/or

explosion, do not fill fuel containers that

are sitting in or on a vehicle or trailer.

The container should be kept tightly

closed in order to limit the amount of

moisture that gets into the mixture.

The machine's fuel tank should be

cleaned as necessary.

Fuel mix ages

If not using MotoMix, only mix sufficient

fuel for a few days of work, not to exceed

30 days of storage. Store in approved

fuel-containers only. When mixing, pour

oil into the container first, and then add

gasoline. Close the container and shake

it by hand to ensure proper mix of oil and

gasoline.

WARNING

Shaking fuel can cause pressure to build

in the fuel container. To reduce the risk

of fire and severe personal injury or

property damage from fuel spraying,

allow the fuel container to sit for several

minutes before opening. Open the

container slowly to release any residual

pressures. Never open the fuel

container in the vicinity of any ignition

source. Read and follow all warnings

and instructions that accompany your

fuel container.

Dispose of empty mixing-oil containers

only at authorized disposal locations.

WARNING

Removing the cap on a pressurized fuel

tank can result in gasoline, vapors and

fumes being forcefully sprayed out from

the tank in all directions. The escaping

gasoline, vapors or fumes, sometimes

referred to as fuel spraying or

"geysering," can cause serious personal

injury, including fire and burn injury, or

property damage.

Fuel spraying can occur when the

engine is hot and the tank is opened

while under pressure. It can occur in hot

environments even if the engine has not

been running. Spraying is more likely to

occur when the fuel tank is half full or

more.

Avoid Injuries from Fuel Spraying.

Always follow the fueling instructions in

this manual:

– Treat every fuel tank as if it is

pressurized, particularly if it is half

full or more.

– Always allow the power tool to cool

adequately before attempting to

open the fuel tank or refueling; this

will take longer in hot conditions.

Gaso

-

line

Oil (STIHL 50:1 or equiva

-

lent high-quality oils)

US gal. US fl.oz.

12.6

2 1/2 6.4

5 12.8

Fueling

Page is loading ...

STIHL HL 94 K (145°) User manual

This manual is also suitable for

STIHL HL 94 K (145°) User manual

in other languages

Related papers

Other documents