English version
4
TV019 Sweex 19" LCD TV with built-in DVD-player
Dear Customers
Thanks for purchasing this TFT-LCD TV/Monitor. We strongly recommend that you carefully read the safety and operation instructions before operating your
TV/Monitor. FOLLOW INSTRUCTIONS AND HEED ALL WARNINGS on your TFT-LCD TV/Monitor and in this manual.
Safety information
Note:
Before connecting the AC power cord to the DC adapter outlet, make sure that the voltage designation of the DC adapter corresponds to the local electrical
supply. If you are unsure about your power supply, please ask the local power company.
Caution:
To avoid electric shock, never touch the inside of the LCD TV/Monitor. Only qualified technicians should open the case of the LCD TV/Monitor.
Warning:
Do not ignore the safety purpose of grounding-type. A grounding type plug has two blades and a third grounding pin. The third pin is provided for your safety. If
the plug does not fit, ask the electrician to replace the obsolete outlet. Do not modify the plug!
To reduce the risk of fire or electric shock, and annoying interference, use the recommended accessories only.
English version
5
Precautions
Please read the below precautions carefully before operating the unit.
Power cord protection:
1. Never use your LCD TV/Monitor if the power cord has been damaged. Do not put anything on the power cord, and keep the power cord away from where
people can easily trip over it.
2. Be sure to hold the plug , do not pull the cord when disconnecting the LCD TV/Monitor from an electric socket.
3. Locate your LCD TV/Monitor near an easy accessible AC outlet.
Placement:
1. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the device.
2. Never placing the LCD TV/Monitor in areas under direct sun-light, with high temperature or with high humidity or high level of dust which may cause
damages on the internal parts of the LCD TV/Monitor.
3. Place the LCD TV/Monitor on a solid surface and treat it carefully. The screen is made of thin glass with a plastic front surface and can be damaged by
dropping, hitting or scratching.
Non-use periods:
Unplug the LCD TV/Monitor when it will no be used for a long period.
Foreign objects:
Never insert anything metallic into the cabinet openings of the TV/Monitor. Doing so may cause the danger of electric shock.
Keep away from water/magnetic fields:
1. Do not expose the LCD TV/Monitor to rain or use it near water source. If the LCD TV/Monitor got wet, unplug it and contact an authorized dealer
immediately.
2. Do not clean the front panel with Ketone-type materials, ethyl alcohol, toluene, acid, methyl, or chloride since they may cause damage on panel.
3. Do not place magnetic objects close to the LCD TV/Monitor.
Stacking:
Opening in the LCD TV/monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be blocked or covered. Never use the
unit on a bed, sofa, rug, or other uneven surfaces. Doing so may block the ventilation openings in the bottom of the unit. If you place the LCD TV/Monitor in a
bookcase or some other enclosed place, please make sure to provide adequate space for ventilation.
Servicing:
1. If the LCD TV/Monitor does not operate normally – In particular, if there are any unusual sounds or smells coming from the unit - just unplug it immediately
and contact an authorized dealer or service center.
2. Unplug the LCD TV/Monitor from the AC outlet before any service.
3. Make sure the service technician uses authorized replacement parts or their equivalents. Unauthorized parts any cause fire, electrical shock, or other hazard.
4. Following any service or repair, be sure the service technician performs safety checks to certify that the TFT LCD TV/Monitor is in safe operating order.
English version
6
Unpacking
Please make sure that the following items are included with your LCD TV/Monitor. If any item is missing, please contact your dealer.
TFT LCD TV/ Monitor
Remote control Operation manual DC adapter
Power cord RCA cable Base replacement for wall mounting
English version
7
I. View of the TV/Monitor
Front view Back view
1. Remote sensor 12. DVD disc slot in
2. Power button & indication light 13. DC input jack/Car cord input jack
3. DVD play/pause button 14. VGA jack
4. DVD stop playing button 15. SCART jack
5. DVD open/close button 16. S-video jack
6. CH+/Up direction button 17. Video jack
7. CH-/Down direction button 18. Audio in (Left) jack
8. VOL+/Right direction button 19. Audio in (Right) jack
9. VOL-/Left direction button 20. PC audio in jack
10. Menu button 21. Earphone
11. TV /AV function switch button 22. TVRF antenna jack
English version
8
II. Remote control reference guide
English version
9
Remote control function
1. Unit STANDBY button
2. 0-9 Numerical button
3. Volume up button
4. Display DVD title menu.
5. Volume down button
6. Display the source and channel’s information
7. navigation button
8. navigation button
9. ENTER button
10. navigation button
11. Display LCD OSD Menu
12. Display INPUT source
13. Display video picture modes
14. Play/Pause DVD playing
15. Stop DVD playing
16. Enter into teletext mode or DVD fast rewind playing
17. View a page of text in teletext mode or DVD fast forward playing.
18. Display the index page in teletext mode or replay the current program from the previous chapter or DVD skip backward playing
19. Change the display size in teletext mode or advance forward to the next chapter or DVD skip forward playing.
20. To select DVD program playback or display red subject in teletext mode.
21. Intro/Scan/9 picture display or display green subject of teletext.
22. Repeat playback or display yellow subject of teletext.
23. Repeat A-B playback or display blue subject of teletext.
24. To reveal or hidden the hidden words in teletext mode or select zoom of DVD playback.
25. Sub coded page access in teletext mode or select DVD different playback angle
26. Go to function in DVD mode or keep page display in teletext mode.
27. Exit teletext program in teletext mode or switch the dialogue at the bottom of the screen in DVD mode
28. Slow/Step the speed of DVD playing
29. Select the NICAM or DVD audio channels
30. Select different sound settings
31. MUTE button
32. Display the setup menu of DVD
33. navigation button
34. Select previous channel
35. Display DVD-disc menu
36. Select next channel
37. -/-- button
38. Cycle between previous and present channel viewed
39. Eject the DVD in DVD mode or execute position auto adjust function in PC mode.
English version
10
Remote control battery installation and cautions
Replace battery by following the below steps:
Requires one pair of AAA batteries.
1. Open the battery cover as shown below:
2. Install the battery into the battery tray.
3. Close the battery cover
Caution:
1. Keep the battery out of children’s reach.
2. Don’t attempt to recharge, short-circuit, disassemble, heat or throw the batteries into the fire.
3. Always replace both batteries at the same time. Never mix new and old batteries or batteries of a different type.
4. If you don’t intend to use the remote control for an extended period, remove the batteries to prevent possible leakage and corrosion.
Notes:
1. Do not drop, apply shock or step on the remote control.
2. Do not spill water on the remote control.
3. Do not use the remote control for other equipments at the same time
4. If the TV does not operate even when operating the remote control from a close range, you need to replace the batteries. Refer to the label on the back of
the remote control for directions for replacing batteries.
English version
11
III. Installation and connection
Connect the LCD TV/monitor
1. Connect the TVRF source with the antenna port. TVRF signal including: Receiving antenna /satellite TV/CATV net. You can use 75
coaxial cable to
connect the outdoor antenna.
Outdoor Antenna Connection:
Use 75
coaxial cable plug or 300-75 impedance converter to plug in antenna input terminal on the rear of the cabinet.
VHF ANTENNA UHF ANTENNA
MIXER
75 CO-AXIS CABLE
INPUT TERMINAL OF ANTENNA
CO-AXIS ANTENNA PLUG
75 CO-AXIS CABLE
ANTENNA IN JACK
English version
12
2. Connect the audio sources (Including DVD, VCDR, CAMCORDER and PC) to the proper AUDIO input jacks ‘L’ and ‘R’.
3. Connect the video source to the VIDEO jack by RCA cable.
4. If the video source has a SCART output jack, you can connect the signal to the monitor by the SCART cable.
5. Connect the video source to the S-VIDEO input jack of the monitor by the S-video cable (Pretending that the video source has S-video output jack).
6. Insert the AC power to the DC adapter, then connect it’s DC output jack to the12V input jack of the monitor.
7. When using the LCD as a computer screen, connect the PC to the VGA jack from the monitor by the relevant cable.
IV. TV/Monitor screen operation
(1) Basic operation
1. Press the
POWER button on the unit or the STANDBY button on the remote control to switch on the power, the indication light will be in blue color .
Press the POWER or STANDBY button again to switch off the power, and the light will be in red color.
2. The Picture setup, Sound setup, Previous channel can be memorized before you switch off the TV/Monitor. The TV/Monitor will re-start under the previous
state when you switch on it again.
3. Press the VOL - or VOL + button to adjust the volume output. Press the VOL - button repeatedly to decrease the volume; press the VOL + button repeatedly
to increase the volume from 0 to 100.
(2) View the TV plays.
1. Press the INPUT button on the remote control to select the TV function mode. Channel ‘1’ will appear on the top left hand corner after channel searching
is completed . Press the CH- or CH+ button to select the previous or next channels; or press the 0-9 buttons to enter a channel number directly, or press
the -/-- button until the screen display ‘-’ or ‘--’, then use the 0-9 numerical buttons to enter a channel number from 1 to 199.
2. Press the
button on the remote control to select from the present channel and the previous channel.
3. Press the PMODE button repeatedly to cycle through the available video picture modes from the below 4 types
4. Press the SMODE button to repeatedly to cycle through the available sound modes from the below 4 types
5. Press the MUTE button to cut off the sound output, press this button again to resume sound output.
6. Press the DISPLAY button to display the preset channel information
STANDARD MILD FRESH PERSONAL
MUSIC THEATRE PERSONAL VOICE
English version
13
(3) View the AV signal sources (DVD/VCR/CAMCORDER)
Press the INPUT button on the remote control repeatedly to cycle through the available source in following:
(4) View the TELETEXT program
(Optional. If TV has this function.)
1. Press the INPUT button to select the TV mode. Then press the CH- or CH+ button on the remote control to select TV channel in order to pick up the
picture signal of TELETEXT. (Firstly you must view the second part of chapter V to complete the TV channel searching).
2. Press TEXT button to enter into picture showing mode. The button can allow you:
3. Press the CH- or CH+ button to select the previous page or the next page; use the 0-9 numerical buttons and the -/- - button to enter into a numerous
page.
4. Refer to the chapter of ‘Remote control reference guide’ to grasp other functions of the TELETEXT buttons.
(5) PC screen
Press the INPUT button to select the VGA input (TV into PC) mode. The will be a ‘PC’ mark appears on the right of the top corner of the monitor.The unit has a
VGA jack for a normal computer. Connect the monitor with a PC by this jack and the unit can be used as the monitor of the PC.
V. Menu setting and adjustment
1. PICTURE SETTING
Press the LCD MENU button on the remote control, there will be a menu displayed on the screen as below:
On this menu, the Picture setting icon of
is in red frame.
TV SCART AV PC-RGB
ENTER INTO
THE PICTURE
EXIT
S-VIDEO
DVD
ENTER INTO
THE TEXT
English version
14
(1). Use the button firstly, the cursor will be on the line of “Picture Mode: Vivid”. And then, press the or button repeatedly to select the sound
mode from Vivid, Soft, Normal or User.
(2). After select the Picture Mode, you can use the
or button to select the item of Brightness, Contrast, Saturation, Sharpness and Hue. And then use
the
or button to adjust the value of each item respectively from 0∼100.
Note:
Only the item of Brightness and Contrast could be operated in the PC signal source.
(3) Move the cursor on the line of “Scale”. And then, press the
or button repeatedly to select the picture screen display mode among FULL, 4:3,
Panorama, ZOOM, ZOOM2 etc.
After setting, press the LCD MENU button to return to the root menu or exit the setting
2. SOUND SETTING
Press the LCD MENU button on the remote control, and then press the
button to select the Sound setting, the Menu will be shown as below:
On this menu, the Sound setting icon of
is in red frame.
(1). Use the
button firstly, the cursor will be on the line of “Sound Mode: Normal”. And then, press the or button repeatedly to select the picture
mode from Normal, News, Movie or User.
(2). After select the Sound Mode, you can use the
or button to select the item of Volume, Bass, Treble and Balance. And then use the or
button to adjust the value of each item respectively from 0∼100.
After setting, press the LCD MENU button to return to the root menu or exit the setting menu.
3. CHANNEL SETTING( FOR TV SIGNAL SOURCE ONLY)
Press the LCD MENU button on the remote control, and then press the
button to select the Channel setting, the Menu will be shown as below:
English version
15
On this menu, the Channel setting icon of
is in red frame.
(1). Auto Tune
Use the
button firstly, the cursor will be on the line of “Auto Tune”. And then, press the button again, a menu will be displayed as followed:
As shown on the menu, the TV will automatically search stations. When searching, press the LCD MENU button to cancel searching. After the searching,
the TV will begin to play the station 1.
(2). Manual Tune
Select the ‘Manual Tune’ first, and then press the
button:
As shown on the menu, the channel number will displayed on the screen. Press the
or button repeatedly until you search a required station. Press the
or button to move cursor to Search, and press or button to search TV signal .At last press the button to move cursor to store, and
press
button to save your selected channel.
English version
16
(3). Fine Tune
Select the ‘Fine Tune’ first, and then press the
or button:
As shown on the menu, the TV signal could be fine tuned by
or button repeatedly until you get the best playing effect. Press the or
button to move cursor to Store, and press
button to save .
(4). Skip
Press the
or button to select the skip setting, and press the or button repeatedly to select On or Off.
Setting to “On”, the channel will not be selected by Channel Up/Down keys.
(5). Sound SYS.
Press the
or button to select the Sound SYS. setting, and press the or button repeatedly to select. You could choose D/K, L, B/G or I
according to your local TV sound system.
(6). Swap
Select the “Channel Swap”, and then press the
button, the screen will display:
The channels indicated at “Channel 1” and “Channel 2” will swap position. Press
or button to move the cursor on the line of “Channel 1” or
“Channel 2”, you can enter into a station number from 1-200 by the
and button as the appointed station number for replacing the current
station number. After entered into the number, press
button again to move the cursor will on the line of “Swap”, then press button.
After setting, press the LCD MENU button to return to the root menu or exit the setting menu.
English version
17
4. FUNCTION SETTING
Press the LCD MENU button on the remote control, and then press the
button to select the Function setting, the menu will be shown as below:
On this menu, the Function setting icon of
is in red frame.
(1). Language
Use the
button firstly, the cursor will be on the line of “Language English”. And then, press the or button repeatedly to select the language
you need.
(2). Blue Back
Move the cursor to the line of “Blue Back On”. And then, press the
or button repeatedly to select the On or Off
(3). TXT LANGUAGE
Move the cursor to the line of “TXT LANGUAGE WEST”. And then, press the
or button repeatedly to select the West, East, Russian, Arabic or Farsi
according to your meaning.
(4). Color Temp.
Move the cursor to the line of “Color Temp. Normal”. And then, press the
or button, a menu will be displayed as followed:
English version
18
Press the or button repeatedly, you could select User, Normal, Warm or Cool according to your request.
Note: Only if Color Temp. is set to “User”, then you can adjust “User – R”, “User – G” and “User – B”.
(5). DNR
Press the
or button repeatedly, you could select Strong, Normal or Weak.
(6) Reset
Press the
or button to reset
After setting, press the LCD MENU button to return to the root menu or exit the setting menu.
Note:
a. Only the item of Language, Color Temp. and Reset could be operated in the PC signal source.
b. The item of Blue Back could not be operated in AV, Svideo and SCART signal source.
5. PC SETTING (FOR PC SIGNAL SOURCE ONLY)
Press the LCD MENU button on the remote control to display the menu, and then press the
button to select the PC setting, and the menu will be shown on
the screen as below:
On this menu, the PC setting icon of
is in red frame. Press . You can use the or button to select the item of Clock, Phase, H-Position or
V-Position. And then use the
or button to adjust the value of each item respectively from 0∼100.
After setting, press the LCD MENU button to return to the root menu or exit the setting menu.
English version
19
VI. DVD Player Operation
a. Basic operation
1. Press the SOURCE button on the remote control to select the DVD function mode. Insert a disc into the slot of the DVD player and it will start to read the disc
automatically.
2. Press the
button on the remote control, the disc will automatically eject.
Note:
Insert the disc with reflective data side facing to the front of the TV. Some slight picture and sound noise are produced when the disc is loading, unloading and
during playback. This is normal and can be ignored.
HOW TO SELECT THE TRACK
If you want to play the second track or chapter, press the number button “2” directly. Then press the ENTER button to play.
HOW TO PAUSE PLAYBACK (STILL PLAYBACK)
Press the PLAY/PAUSE button once during playback.
Press the PLAY/PAUSE button again to resume normal playback.
HOW TO REMOVE THE DISC
Press the
button on the remote control.
Wait until the disc is completely ejected before removing.
HOW TO STOP PLAYBACK
Press the STOP button once, the DVD video player will stop. Then press the PLAY button to resume playback of the disc from the same point. Press the STOP
button twice, and disc will stop completely. Press the PLAY button to start the DVD playback from the first track.
FAST FORWARD/ BACKWARD
Press the
or buttons to toggle between different playback speeds in sequence at x2, x4, x8 or x20. Press the button to return playing at
normal speed.
Note: The sound is not available while playing in this mode.
SKIP TO NEXT/ PREVIOUS TRACK
Press the
or buttons to select the next track or previous track.
b. Slow Play
Press the SLOW/STEP (>I) button when playing, the disc will play at 1/2, 1/3,1/4, 1/5,1/6, 1/7 of the normal speed. Press the
button to return
playing at normal speed.
Note:
The sound is not available while playing in this mode.
c. Zoom Picture
This DVD video player allows you to zoom in/out of a picture as well as shift the zoom point. Press the ZOOM button during normal play or when in slow
motion. The DVD player magnifies the center of the picture at 2x, 3x, 4x, 1/2, 1/3, 1/4 of the normal picture.
English version
20
d. Repeat Play
You can use the REPEAT button to repeat the play of various sections of your DVD.
Press the REPEAT button once to repeat playing the present chapter.
Press the REPEAT button again to repeat playing the present title.
Press the REPEAT button third time to repeat playing the whole disc.
Press the REPEAT button for the fourth time to cancel repeat play and return to normal play.
Note:
For different discs, the REPEAT button may have a different function.
REPEAT A to B SPECIFIC SECTION
You can repeat a specific section by the A-B button on the remote control. Firstly press the A-B button at the beginning of the section you want, then press it
again at the end of the section. The unit will now repeat playing from A to B. If you want to cancel the repeat section, please press the A-B button once again.
Note:
Some discs will not respond to the A-B repeat function.
e. Mute
Press the MUTE button on the remote control to suppress the sound output while a disc is playing. Press the same button again to resume playing with sound.
f. Menu playback
Press the D.MENU button to display disc menu or return to the root menu when playing the DVD discs.
Note:
For different DVD discs, the D.MENU button may have different menu display information.
g. Title playback
Press the TITLE button when playing the DVD discs, there will be an indication “TITLE“ on the screen.
Press the
or buttons to select your favourite title and press the ENTER button to play from the first chapter of selected title.
h. Display
During playback, press the D.DISP button on the remote control to show the current information available. The following information will appear - Title Elapsed;
Title Remain; Ch. Elapsed; Ch. Remain; Display Off and so on.
Note:
For different discs, D.DISP button may have a different function.
i. Playing in a Favourite Order
Combine your favourite titles, chapters or tracks and play them in your favourite order.
HOW TO SET TITLES, CHAPTERS, OR TRACKS IN A FAVOURITE ORDER
The program playback function will automatically playback titles, chapters or tracks in the order preprogrammed.
English version
21
1. Insert a disc, press the PROG button, the menu will appear on the screen, as following:
PROGRAM : TT(- -)/CH(- -)
01 TT: CH: 06 TT: CH: 11 TT: CH: 16 TT: CH:
02 TT: CH: 07 TT: CH: 12 TT: CH:
03 TT: CH: 08 TT: CH: 13 TT: CH:
04 TT: CH: 09 TT: CH: 14 TT: CH:
05 TT: CH: 10 TT: CH: 15 TT: CH:
PLAY CLEAR
2. Input the numbers to select the title and chapter (track) you want, then press the or buttons to move the cursor to input the next one.
3. Press the
or buttons to select and highlight the word PLAY, then, then press the ENTER button. The DVD video player starts memory playback.
Notes:
• When the DVD video player is switched off, or if the discs are removed, the program item will be removed.
• For different discs, PROG button may have a different function.
• If you press the STOP button once the DVD video player will stop. At this point, press the ENTER button to re-start the disc from the same point.
• If you press the STOP button twice the program playing will be cancelled.
j. Selecting the Camera Angles Setting
This DVD video player allows you to select from several different angles. Press the ANGLE button while playing back a scene recorded with multiple angles. You may only
press the ANGLE button when the angle icon appears on the DVD display. Each time you press the ANGLE button, the angle will change.
Notes:
The angle function will not work on DVD video discs that do not contain recorded multiple angles.
During still playback, you are able to change the camera angle. However, when you resume to normal playback, the camera angle changes to the new
settings.
The angle icon indicator will illuminate while playing back a title that contains at least one scene recorded with multiple angles.
k. Selecting Subtitles
This DVD video player allows you to display subtitles which are included on the disc.
By Pressing the SUBTITLE button during playback, you have the option to select a preferred subtitle from those included on the DVD video disc.
To turn off the subtitle function, press the SUBTITLE button during playback until the subtitles disappears.
Notes:
With some DVD discs, you may not be able to turn off the subtitles and they will appear on screen automatically.
As you press the SUBTITLE button, the subtitles may not appear immediately during some screens.
English version
22
l. Selecting languages
This DVD video player allows you to select a preferred languages which are included on the Multi-languages DVD discs.
By Pressing the LANG button once during playback to display current language, press the LANG button again to toggle between different language mode in
sequence.
Note:
For MP3/CD discs playback, press the LANG button to switch between different audio channels in sequence.
m. MP3/JPEG playback
1. In DVD mode, Insert a MP3 or JPEG CD into the disc slot, the DVD video player will initialize the disc and the directory (folder) will be shown on screen.
The first MP3 or JPEG file will be played automatically.
2. Press the
or buttons to select the folders, MP3/JPEG files or modes and press the ENTER button on the remote control to enter the folder or
start playback.
3. When playing MP3 files, press the
or buttons during playback to skip the tracks.
Notes:
• When playing MP3 Files, there is no picture display ,only there is audio output.
• When viewing the JPEG pictures, you could press the
or buttons to flip or rotate the picture.
• When viewing the JPEG pictures, you could press D.MENU button to enter into preview mode to display 12 pictures. Press
or button to select
next or last page or press the numeric buttons to view the corresponding pictures.
n. INTRO playback
Press the INTRO button to play the first 10 seconds of each track when playing CD discs.
o. Customizing the Function Settings
This DVD video player allows you to customise the performance to your personal preference.
DISPLAYING THE SETUP MENU SCREEN:
The DVD SETUP MENU screen asks you to select a setting category from SYSTEM SETUP, LANGUAGE SETUP, AUDIO SETUP and DIGITAL SETUP. The selected category
will provide you with the setting details on the TV screen. Please look at the following for more details.
Press the DVD SETUP button to enter the SETUP MENU. Press the
or buttons to select and highlight the category. Then press the ENTER button to
confirm. Press the DVD SETUP button again to return to the root menu or to exit the setting menu.
English version
23
Note:
Functions and menu may change without notice.
1. System Setup
SOURCE
This feature is not available on this model
TV SYSTEM
This menu enables you to set the picture format for your TV/DVD between NTSC/ PAL/ AUTO according to your request and local TV system.
TV TYPE
This menu enables you to select one of the three aspect ratios:
4:3 PS / 4:3LB / 16:9
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/