KitchenAid 730-0732 Installation Instructions And Use & Care Manual

FREESTANDING OUTDOOR GRILL

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-877-373-2301

or visit our website at www.Nexgrill.net

ASADORE AUTÓNOMO PARA EXTERIORES

Instrucciones de instalación y Manual de uso y cuidado

Para consultas respecto a características, funcionamiento, rendimiento, piezas, accesorios o servicio técnico, llame al: 1-877-373-2301

o visite nuestro sitio de internet en www.Nexgrill.net

GRIL D'EXTÉRIEUR AUTOPORTANT

Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, des accessoires ou du service,

composer le : 1-877-373-2301

ou visitez notre site web www.Nexgrill.net

Table of Contents/Índice/Table des matières..................................................................2

720-0732 (LP) 730-0732 (NG)

2

TABLE OF CONTENTS

OUTDOOR GRILL SAFETY ...........................................................3

INSTALLATION REQUIREMENTS................................................5

Tools and Parts............................................................................5

Location Requirements................................................................5

Product Dimensions ....................................................................6

Electrical Requirements...............................................................6

Gas Supply Requirements...........................................................7

Gas Connection Requirements....................................................7

INSTALLATION INSTRUCTIONS..................................................8

Freestanding Outdoor Grill Installation ........................................8

Make Gas Connection................................................................11

GAS CONVERSIONS ...................................................................14

Tools and Parts for Gas Conversion..........................................14

Conversion from LP Gas to Natural Gas...................................14

Check and Adjust the Burners...................................................18

OUTDOOR GRILL USE ................................................................19

Using Your Outdoor Grill............................................................19

Hood Lights.................................................................................20

Using Your Searing Side Burner................................................21

Using Your Rotisserie Burner.....................................................22

Rotisserie Cooking Tips .............................................................22

TIPS FOR OUTDOOR GRILLING ................................................23

Cooking Methods........................................................................24

Grilling Chart...............................................................................24

OUTDOOR GRILL CARE..............................................................26

Replacing the Igniter Battery......................................................26

Changing the Light Bulb.............................................................26

General Cleaning........................................................................27

TROUBLESHOOTING ..................................................................28

ASSISTANCE................................................................................29

Accessories................................................................................29

REPLACEMENT PARTS..............................................................30

WARRANTY ..................................................................................34

ÍNDICE

SEGURIDAD DEL ASADOR PARA EXTERIORES....................36

REQUISITOS DE INSTALACIÓN.................................................38

Herramientas y piezas................................................................38

Requisitos de ubicación.............................................................38

Medidas del producto.................................................................39

Requisitos eléctricos ..................................................................39

Requisitos del suministro de gas...............................................40

Requisitos para la conexión de gas...........................................40

INSTRUCCIONES DE INSTALACIÓN.........................................42

Instalación del asador autónomo para exteriores......................42

Conexión del suministro de gas.................................................45

CONVERSIONES DE GAS...........................................................48

Herramientas y piezas para la conversión de gas.....................48

Conversión de gas LP a gas natural..........................................48

Revise y regule los quemadores................................................52

USO DEL ASADOR PARA EXTERIORES ..................................54

Cómo usar el asador para exteriores.........................................54

Luces de la capota.....................................................................56

Cómo usar el quemador lateral para dorado rápido..................56

Cómo usar el quemador del rostizador......................................57

Consejos para la cocción con el rostizador ...............................58

CONSEJOS PARA ASAR AL AIRE LIBRE.................................59

Métodos de cocción....................................................................59

Cuadro para asar........................................................................60

CUIDADO DEL ASADOR PARA EXTERIORES.........................63

Cómo reemplazar la batería del encendedor.............................63

Cómo cambiar el foco ................................................................63

Limpieza general........................................................................64

SOLUCIÓN DE PROBLEMAS......................................................66

ASISTENCIA..................................................................................66

Accesorios..................................................................................66

PIEZAS DE REPUESTO...............................................................67

GARANTÍA ....................................................................................70

TABLE DES MATIÈRES

SÉCURITÉ DU GRIL D'EXTÉRIEUR............................................72

EXIGENCES D’INSTALLATION...................................................74

Outils et pièces...........................................................................74

Exigences d'emplacement.........................................................74

Dimensions du produit................................................................75

Spécifications électriques...........................................................75

Spécifications de l'alimentation en gaz......................................76

Exigences concernant le raccordement au gaz.........................77

INSTRUCTIONS D’INSTALLATION ............................................78

Installation du gril d’extérieur autoportant..................................78

Raccordement au gaz................................................................81

CONVERSIONS POUR CHANGEMENT DE GAZ.......................84

Outils et pièces pour conversion de gaz....................................84

Conversion de propane à gaz naturel........................................84

Contrôle et réglage des brûleurs................................................88

UTILISATION DU GRIL D’EXTÉRIEUR.......................................90

Utilisation du gril d’extérieur.......................................................90

Lampes sous le couvercle..........................................................92

Utilisation du brûleur à rôtissage latéral.....................................92

Utilisation du brûleur de tournebroche.......................................93

Conseils de cuisson à l’aide du tournebroche ...........................94

CONSEILS POUR L'UTILISATION DU GRIL D'EXTÉRIEUR.....95

Méthodes de cuisson .................................................................95

Tableau de cuisson au gril .........................................................96

ENTRETIEN DU GRIL D’EXTÉRIEUR.........................................99

Remplacement de la pile de l’allumeur......................................99

Changement de l’ampoule d’éclairage.......................................99

Nettoyage général....................................................................100

DÉPANNAGE ..............................................................................102

ASSISTANCE..............................................................................102

Accessoires..............................................................................102

PIÈCES DE RECHANGE............................................................103

GARANTIE...................................................................................106

3

OUTDOOR GRILL SAFETY

IMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used at elevations above 2000 ft (609.6 m) orifice

conversion is required. See “Gas Supply Requirements” section. It is the responsibility of the installer to comply with the minimum

installation clearances specified on the model/serial rating plate. The model/serial rating plate for freestanding models can be found on

the left-hand inside cabinet wall.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or your fire department.

DANGER

WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of

this or any other appliance.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

■ If using a ball valve, it shall be a T-handle type.

■ A flexible gas connector, when used, must not exceed 3 feet.

4

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the outdoor cooking

gas appliance, follow basic precautions, including the

following:

■ Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable trailer,

boat or in any other moving installation.

■ Always maintain minimum clearances from combustible

construction, see “Location Requirements” section.

■ The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

■ This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or any

other enclosed area.

■ Keep any electrical supply cord and fuel supply hose away

from any heated surfaces.

■ Keep outdoor cooking gas appliance area clear and free

from combustible materials, gasoline and other flammable

vapors and liquids.

■ Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation openings of the cylinder enclosure free

and clear from debris.

■ Open the cabinet door and inspect the gas cylinder supply

hose before each use of the outdoor cooking gas

appliance. If the hose shows excessive abrasion or wear,

or is cut, it MUST be replaced before using the outdoor

cooking gas appliance. Contact your dealer and use only

replacement hoses specified for use with the outdoor

cooking gas appliance.

■ Visually check the burner flames.

They should be blue. Slight

yellow tipping is normal for LP

gas. The flames should be

approximately 1" (2.5 cm) high.

■ Check and clean burner/venturi tube for insects and insect

nest. A clogged tube can lead to fire under the outdoor

cooking gas appliance.

■ The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the

Specification for LP Gas Cylinders of the U.S. Department

of Transportation (DOT) or the National Standard of

Canada, CAN/CSA-B339, Cylinders, Spheres, and Tubes

for Transportation of Dangerous Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device compatible

with the connection for outdoor cooking gas appliances.

■ Always check connections for leaks each time you connect

and disconnect the LP gas supply cylinder. See

“Installation Instructions” section.

■ When the outdoor cooking gas appliance is not in use, the

gas must be turned off at the supply cylinder.

■ Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and

removed from the outdoor cooking gas appliance.

■ Cylinders must be stored outdoors and out of the reach of

children and must not be stored in a building, garage, or

any other enclosed area.

■ The pressure regulator and hose assembly supplied with

the outdoor cooking gas appliance must be used. A

replacement pressure regulator and hose assembly

specific to your model is available from your outdoor

cooking gas appliance dealer.

■ Gas cylinder must include a collar to protect the cylinder

valve.

■ For appliances designed to use a CGA791 Connection:

Place a dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage

of propane.

If the following information is not followed exactly, a fire

causing death or serious injury may occur.

■ Do not store a spare LP gas cylinder under or near this

outdoor cooking gas appliance.

■ Never fill the cylinder beyond 80 percent full.

1"

(2.5 cm)

5

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

Parts Supplied

■ Gas pressure regulator/hose assembly set for 11" WCP LP

gas

■ Right side shelf with sear burner

■ Left side shelf

■ Searing side burner control knob

■ “AA” Batteries (1)

■ Warming rack

■ Cooking grid

■ Side burner cooking grid

■ Natural gas orifice for rotisserie/infrared burner

Parts Needed

■ 20 lb LP gas fuel tank - approximately 18" (45.7 cm) height

Parts Needed for Conversion to Natural Gas

■ Natural gas conversion kit Part Number 710-0003. See

“Assistance” section to order. The conversion kit includes:

■ Natural gas regulator 4" W.C. (marked “Natural Gas

Regulator”)

■ 10 ft (3.0 m) Natural gas hose with quick connector

■ 5.9" (150 mm) Natural gas regulator hose

■ 6 mm nut driver

■ 6mm wrench

■ Hex key

■ Gas line shutoff valve

■ ½" male pipe thread nipple for connection to pressure

regulator.

■ LP gas-resistant pipe-joint compound

■ CSA design-certified outdoor flexible stainless steel appliance

connector (4-5 ft [1.2-1.5 m]) or rigid gas supply line as

needed.

Location Requirements

Select a location that provides minimum exposure to wind and

traffic paths. The location should be away from strong draft areas.

Do not obstruct flow of combustion and ventilation air.

Clearance to combustible construction for freestanding outdoor

grills:

■ A minimum of 24" (61 cm) must be maintained between the

front of the grill hood, sides and back of the grill and any

combustible construction.

■ A 24" (61 cm) minimum clearance must also be maintained

below the cooking surface, and the grill shall not be used

under overhead combustible construction.

Rotisserie (accessory)*

If you equip your grill with a rotisserie, a 6" (15.2 cm) minimum

clearance is needed for the rotisserie motor.

A grounded, 3-prong outlet located to the left of the grill is

required.

*See “Assistance” section to order.

■ Phillips screwdriver

■ Wrench or pliers

■ Pipe wrench

■ Scissors or cutting pliers

(to remove tiedowns)

■ Noncorrosive leak-

detection solution

WARNING

Explosion Hazard

Do not store fuel tank in a garage or indoors.

Do not store grill with fuel tank in a garage or indoors.

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.

Doing so can result in death or fire.

6

Product Dimensions

Electrical Requirements

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Check with a qualified electrician if you are not sure whether the

grill is properly grounded.

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical supply is

required.

It is recommended that a separate circuit servicing only this grill

be provided.

■ To avoid electrical shock, do not immerse cord or plugs in

water or other liquid.

■ Unplug from the outlet when not in use and before cleaning.

Allow to cool before putting on or taking off parts.

■ Do not operate any outdoor cooking gas appliance with a

damaged cord, damaged plug, or after the appliance

malfunctions or has been damaged in any manner. Contact

the manufacturer for repair.

■ Do not let the cord hang over the edge of a table or touch hot

surfaces.

■ Do not use an outdoor cooking appliance for purposes other

than intended.

■ When connecting, first connect plug to the outdoor cooking

gas appliance then plug appliance into the outlet.

■ Use only a Ground Fault Interrupter (GFI) protected circuit

with this outdoor cooking gas appliance.

■ Do not remove the ground prong or use with an adapter of

2prongs.

■ Use only extension cords with a 3 prong grounding plug rated

for the power of the equipment and approved for outdoor use

with a W-A marking.

The model/serial number rating plate is located on the inside of

the left cabinet door. See the following illustration.

Recommended Ground Method

The outdoor grill, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes,

with the National Electrical Code ANSI/NFPA 70, or Canadian

Electrical Code, CSA C22.1.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

12

5/8

"

(32 cm)

52

3/8

"

(133.0 cm)

28" (71.1 cm)

12

5/8

"

(32 cm)

48 5/8"

(123.5 cm)

23"

(58.4 cm)

Electrical Shock Hazard

Use only a UL listed, 14 gauge, 3 wire extension cord

approved for outdoor use, marked W-A, with a

maximum length of 50 ft.

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

A. Model/serial number plate

A. 3-prong ground plug

B. 3-prong polarized type outdoor GFI outlet

C. Ground prong

A

B

C

7

Gas Supply Requirements

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with either the National Fuel Gas Code, ASNI Z223.1/

NFPA 54, Natural Gas and Propane Installation Code, CSA

B149.1, Propane Storage and Handling Code, B149.2, or the

Standard for Recreational Vehicles, ASNI A119.2/NFPA 1192 and

CSA Z240 RV Series Recreational Vehicle Code as applicable.

IMPORTANT: Grill must be connected to a regulated gas supply.

Refer to the model/serial rating plate for information on the type of

gas that can be used. If this information does not agree with the

type of gas available, check with your local gas supplier.

Gas Conversion:

No attempt shall be made to convert the grill from the gas

specified on the model/serial rating plate for use with a different

gas type without consulting the serving gas supplier. The

conversion kit supplied with grill must be used. See “Gas

Conversions” section for instructions.

Gas Pressure Regulator

The gas pressure regulator supplied with this grill must be used.

The inlet (supply) pressure to the regulator should be as follows

for proper operation:

LP Gas:

Operating pressure: 11" (27.9 cm) WCP

Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas:

Operating pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP

maximum.

Contact local gas supplier if you are not sure about the inlet

(supply) pressure.

Burner Requirements for High Altitude

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice

conversion is required. See “Assistance” section to order.

Gas Supply Line Pressure Testing

Testing above ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The grill and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures greater than ½ psi (3.5 kPa).

Testing below ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge) or

lower:

The grill must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than ½ psi (3.5 kPa).

Gas Connection Requirements

20 lb LP Gas Fuel Tank

This grill is equipped for use with a 20 lb LP gas fuel tank (fuel

tank not supplied). A gas pressure regulator/hose assembly is

supplied.

Any brand of 20 lb LP gas fuel tank is acceptable for use with the

grill, provided that it is compatible with the grill’s retention means

(tank tray included).

It is also design-certified by CSA International for local LP gas

supply or for Natural gas with appropriate conversion.

The 20 lb LP gas fuel tank must be mounted and secured.

Door Style Tank Tray

1. Open cabinet doors.

2. Slide the tank tray locking bracket counterclockwise 90° and

pull out the tray.

3. Place the 20 lb LP gas fuel tank bottom collar into the

mounting hole in the tank tray.

WARNING

Explosion Hazard

Use a new CSA International approved “outdoor”

gas supply line.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 11” (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

A. Gas pressure regulator/hose assembly

A. Tank tray locking bracket

A

8

4. Tighten the locking screw against the bottom collar of the

20 lb LP gas fuel tank to secure.

5. Slide the drawer with the 20 lb LP gas fuel tank back into the

cabinet. Turn the tank tray locking bracket clockwise 90° to

tighten.

Natural Gas Conversion

Conversion must be made by a qualified gas technician. The

qualified Natural gas technician shall provide the Natural gas

supply to the selected grill location in accordance with the

National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition,

and local codes. For conversion to Natural gas, the Natural Gas

Conversion Kit supplied with the grill (on some models) or the

Natural Gas Conversion Kit Part Number 710-0003 must be used.

See “Assistance” section for information on ordering.

IMPORTANT: The gas installation must conform with local codes,

or in the absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 - latest edition.

Follow instructions for converting to Natural gas in the “Gas

Conversions” section of this manual or the instructions supplied

with Natural Gas Conversion Kit Part Number 710-0003.

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the grill

and should be in a location that allows ease of opening and

closing. Do not block access to the shutoff valve. The valve is for

turning on or shutting off gas to the grill.

INSTALLATION

INSTRUCTIONS

Freestanding Outdoor Grill Installation

Unpack Grill

1. Remove all packaging materials and remove grill from the

shipping base.

2. Move grill close to desired outdoor location.

3. Open the grill hood.

Remove Packaging Material Inside the Grill

1. Use a utility knife to cut yellow straps and packing tape to

open box from top and remove the boxes.

2. Remove the warming shelf and grill grates from inside the grill

and remove the package inside the firebox.

3. Remove foam block and wrap from inside the grill.

4. Replace the grill grates.

5. Place warming shelf on brackets as shown.

A. Locking screw

B. Bottom collar

C. Mounting hole

A. Tank tray locking bracket

A. Gas supply line

B. Shutoff valve “open” position

C. To grill

A

C

B

A

B

C

A. Warming shelf brackets

B. Warming shelf

Excessive Weight Hazard

Use two or more people to move and install grill.

WARNING

Failure to do so can result in back or other injury.

B

A

9

Attach Right Side Shelf with Sear Burner

1. Unpack right side shelf with sear burner.

2. Open grill lid.

3. Remove 3 screws from the side of the searing side burner.

4. Remove the 3 screws on the grill side panel and 1 screw on

the grill control panel.

5. Lower the side shelf so that the center post (A) slides into the

bracket (B) and align the bottom keyhole slots on the side

shelf with the screw holes on the grill side panel.

IMPORTANT: This step is meant to help with the installation,

but do not depend solely on the bracket to hold the weight of

the sear burner.

6. Attach the top of the side shelf to the grill (A) by inserting the

3 screws removed in Step 3 into the side shelf from inside the

grill hood and tighten. See illustration in Step 8.

7. Attach the bottom of the side shelf to the side panel (B and C)

of the grill by inserting the 3 screws removed from the grill

side panel in Step 4. Tighten the screws. See illustration in

Step 8.

8. Attach the side shelf to the control panel (D) by inserting the

screw removed from the grill control panel in Step 4. Tighten

the screw.

9. Remove the 3 screws from the searing side burner.

10. Remove the searing side burner.

11. Remove the 2 screws from the side burner valve assembly.

See illustration in Step 13.

12. Push the valve stem out through the opening in the front of the

side burner shelf, lining up the holes in the side burner valve

assembly with the openings on the side burner shelf. See

illustration in Step 13.

A. Searing side burner screws

A. Grill control panel screw

B. Grill side panel screws

A

B

A

B

C

D

10

13. Slide the bezel opening over the valve stem and attach the

side burner valve assembly and bezel to the side burner shelf

with the screws removed in Step 9.

14. Replace the searing side burner, angling it so that the valve

orifice goes into the side burner tube.

15. Connect electrical plugs on underside of sear burner.

16. Insert the valve stem into the knob and push knob into place.

17. The igniter battery is not factory installed. A “AA” size alkaline

battery is located in the accessory box on the grill grate. Install

battery at this time following the instructions in “Replacing the

Igniter Battery” section.

Attach Left Side Shelf

1. Unpack left side shelf.

2. Open grill lid.

3. Remove 3 screws from the side of the side shelf.

4. Remove the 3 screws on the grill side panel and 1 screw on

the grill control panel.

A. Bezel

B. Valve stem

A. Electrical plug from grill

B. Electrical plug from sear burner

A

B

A

B

A. Side shelf screws

A. Grill side panel screws

B. Grill control panel screw

A

B

11

5. Lower the side shelf so that the side shelf center post (A)

slides into the bracket (B) and align the bottom keyhole slots

on the side shelf with the screw holes on the grill side panel.

IMPORTANT: This step is meant to help with the installation,

but do not depend solely on the bracket to hold the weight of

the side shelf.

6. Attach the top of the side shelf to the grill (B) by inserting the

3 screws removed in Step 3 into the side shelf from inside the

grill hood and tighten. See illustration in Step 8.

7. Attach the bottom of the side shelf to the side panel (A and D)

of the grill by inserting the 3 screws removed from the grill

side panel in Step 4. Tighten the screws. See illustration in

Step 8.

8. Attach the side shelf to the control panel (C) by inserting the

screw removed from the grill control panel in Step 4. Tighten

the screw.

Make Gas Connection

NOTE: If grill is to be converted to Natural gas, follow instructions

in the “Gas Conversions” section.

20 lb LP Gas Fuel Tank

LP Gas:

IMPORTANT: A 20 lb LP gas fuel tank must be purchased

separately.

IMPORTANT: The gas pressure regulator/hose assembly

supplied with the grill must be used. Replacement gas pressure

regulator/hose assembly specific to your model, is available from

your outdoor grill dealer.

Door Style Tank Tray

1. Open cabinet doors.

2. Slide the tank tray locking bracket counterclockwise 90° and

pull out the tray.

3. Place the 20 lb LP gas fuel tank bottom collar into the

mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the

20 lb LP gas fuel tank to secure.

5. Slide the tank tray with the 20 lb LP gas fuel tank back into the

cabinet and lock the locking bracket.

A

B

A

C

D

A. Tank tray locking bracket

A. Locking screw

B. Bottom collar

C. Mounting hole

WARNING

Explosion Hazard

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 11” (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

A

C

B

12

To Connect the 20 lb LP Gas Fuel Tank:

1. Check that the 20 lb LP gas fuel tank is in the “Off” position. If

not, turn the valve clockwise until it stops.

2. Check that the 20 lb LP gas fuel tank valve has the proper

type-1 external male thread connections per ANSI Z21.81.

3. Check that the burner control knobs are in the “Off” position.

4. Remove any debris and inspect the valve connections, port,

and gas pressure regulator/hose assembly for damage.

NOTE: Always keep the LP cylinder at 90° (upright)

orientation to provide vapor withdrawal.

5. Using your hand, turn the gas pressure regulator/hose

assembly clockwise to connect to the 20 lb LP gas fuel tank as

shown.

Hand tighten only. Use of a wrench could damage the quick

coupling nut.

Make sure that the cylinder valve connection device properly

mates with the connection device attached to the inlet of the

pressure regulator.

6. Open the tank valve fully by turning the valve

counterclockwise. Wait a few minutes for gas to move through

the gas line.

7. Before lighting the grill, test all connections by brushing on an

approved noncorrosive leak-detection solution. Bubbles will

show a leak.

8. If a leak is found, turn the tank valve off and do not use the

grill. Contact a qualified gas technician to make repairs.

9. Go to “Check and Adjust the Burners” section.

To Disconnect the 20 lb LP Gas Fuel Tank:

1. Check that the burner control knobs are in the “Off” position

and the grill is cool.

2. Check that the 20 lb LP gas fuel tank is in the “Off” position. If

not, turn the valve clockwise until it stops.

3. Using your hand, turn the gas pressure regulator/hose

assembly counterclockwise to disconnect to the 20 lb LP gas

fuel tank as shown.

Hand loosen only. Use of a wrench could damage the quick

coupling nut.

4. Place dust cap on cylinder valve outlet whenever the cylinder

is not in use. Only install the type of dust cap on the cylinder

valve outlet that is provided with the cylinder valve. Other

types of caps or plugs may result in leakage of propane.

5. Go to “Plug in Grill” in this section.

A. Gas pressure regulator/hose assembly

B. 20 lb LP gas fuel tank

A

B

A. Gas pressure regulator/hose assembly

B. 20 lb LP gas fuel tank

A

B

13

Plug in Grill

1. Plug extension cord into grounded 3-prong GFI outlet.

■ To avoid electrical shock, do not immerse cord or plugs in

water or other liquid.

■ Unplug from the outlet when not in use and before

cleaning. Allow to cool before putting on or taking off parts.

■ Do not operate any outdoor cooking gas appliance with a

damaged cord, damaged plug, or after the appliance

malfunctions or has been damaged in any manner.

Contact the manufacturer for repair.

■ Do not let the cord hang over the edge of a table or touch

hot surfaces.

■ Do not use an outdoor cooking appliance for purposes

other than intended.

■ When connecting, first connect plug to the outdoor

cooking gas appliance then plug appliance into the outlet.

■ Use only a Ground Fault Interrupter (GFI) protected circuit

with this outdoor cooking gas appliance.

■ Do not remove the ground prong or use with an adapter of

2prongs.

■ Use only extension cords with a 3 prong grounding plug

rated for the power of the equipment and approved for

outdoor use with a W-A marking.

2. Go to “Check and Adjust the Burners” section.

A. 3-prong ground plug

B. 3-prong polarized type outdoor GFI outlet

C. Ground prong

Electrical Shock Hazard

Use only a UL listed, 14 gauge, 3 wire extension cord

approved for outdoor use, marked W-A, with a

maximum length of 50 ft.

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

A

B

C

14

GAS CONVERSIONS

Tools and Parts for Gas Conversion

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Parts supplied

■ Natural gas orifices

Parts needed

■ Natural gas conversion kit Part Number 710-0003. See

“Assistance” section to order. The conversion kit includes:

■ Natural gas regulator 4" W.C. (marked “Natural Gas

Regulator”)

■ 10 ft (3.0 m) Natural gas hose with quick connector

■ 5.9" (150 mm) Natural gas regulator hose

■ 6 mm nut driver

■ 6mm wrench

■ Hex key

IMPORTANT: Gas conversions must be done by a qualified

installer. Before proceeding with conversion, shut off the gas

supply to the appliance prior to disconnecting the electrical power.

Conversion from LP Gas to Natural Gas

Installation of the regulator

1. Turn off the main gas supply valve.

2. Unplug grill or disconnect power.

3. Disconnect 20 lb LP gas fuel tank (if present).

4. Turn off all burner control valves.

5. Remove the 20 lb LP gas fuel tank (if present) from the grill

cart.

6. Use an adjustable wrench to remove the LP regulator from the

manifold.

7. Use an adjustable wrench to install the Natural gas regulator

hose to the manifold and secure. Attach the Natural gas

regulator to the side panel inside the grill cart with the two

screws that are preassembled on the regulator.

Make Gas Connection

1. A combination of pipe fittings must be used to connect the grill

to the existing gas line.

■ The 10 ft (3.0 m) PVC flexible gas supply hose design-

certified by CSA must be used.

■ Pipe-joint compounds suitable for use with Natural gas

must be used. Do not use Teflon

®†

tape.

■ There must be a certified manual shutoff valve in the gas

supply line near the grill for easy access.

2. Connect the brass connector on one end of the 10 ft (3.0 m)

PVC flexible gas supply hose to the Natural gas pressure

regulator.

■ Phillips screwdriver

■ Pipe wrench

■ Adjustable wrench

■ 6 mm socket and wrench

or 6 mm nut driver

■ Thin flat-blade screwdriver

■ Pliers

■ Pipe thread sealant

certified for LP gas

WARNING

Explosion Hazard

Use a new CSA International approved “outdoor”

gas supply line.

Securely tighten all gas connections.

Failure to do so can result in death, explosion, or fire.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

15

3. Connect the quick connector on the other end of the

10 ft (3.0 m) PVC flexible gas supply hose to the rigid Natural

gas supply pipe.

Change Grill Burner Valve Orifices

1. Remove the grates and flame tamers.

2. Remove the screw and cotter clip that hold the burner in

place. Set the screw and clip aside. Remove the burner from

the grill by lifting the burner out.

3. Use a 6 mm socket and wrench or 6 mm nut driver to remove

the brass orifice from the end of gas valve. The main burner

orifice is located behind the LP orifice, so no additional orifice

needs to be installed.

IMPORTANT: Check that the orifice is properly installed

inside of the burner opening.

4. Reinsert the burner and reattach using the 1 screw and cotter

clip previously removed. Repeat the procedure for each main

burner.

5. Position the igniters so they are ¼" (6.0 mm) away from each

burner.

Change the Rotisserie/Infrared Burner Orifice

1. Using a Phillips screwdriver, unscrew the 2 screws and

remove the rotisserie/infrared burner wind baffle.

A. Left side panel

B. Manifold

C. 10 ft (3.0 m) PVC gas hose

D. Natural gas pressure regulator/hose assembly

B

A

C

D

A. Main burner orifice

A

2 screws

Wind Baffle

16

2. Using a Phillips screwdriver, remove the 6 screws at the back

of grill from inside the grill.

3. Remove the access cover at the back of the grill hood by

removing the 6 screws.

4. Using a Phillips screwdriver, remove the 1 screw holding the

spider guard to the burner.

5. Use 24 mm wrench to remove the orifice nut.

6. Take out the orifice support, and then use a 6 mm socket and

wrench or 6 mm nut driver to remove the LP orifice at the end

of the supply pipe. Replace with Natural gas orifice.

IMPORTANT: Check that the orifice is properly installed inside

of the supply pipe.

7. Reinstall the spider guard, access cover, and wind baffle.

Change the Sear Burner Orifices

1. Remove the screw securing the igniter and the 2 searing side

burner screws.

A. Access cover

A

A. Orifice nut

A

17

2. Lift out the searing side burner.

3. Locate the Liquid propane orifice at the end of the valve.

4. Use 6 mm socket wrench or 6 mm nut driver to remove the

orifice. Replace with the Natural gas orifice.

IMPORTANT: Check that the orifice is properly installed inside

of the valve.

5. Reinstall the searing side burner. Make sure that the igniter is

out of the way to allow proper positioning of burner. Use

Phillips screwdriver to attach the mounting screws.

6. Use Phillips screwdriver to reattach the igniter and searing

side burner plate.

7. Reinstall searing side burner cover. Use Phillips screwdriver

to attach mounting screws.

8. Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

9. Test all connections using an approved noncorrosive leak-

detection solution. Bubbles will show a leak. Correct any leak

found.

Record Conversion

1. The appliance nameplate is located inside the grill cabinet on

the left-hand cabinet side. With a permanent marker, check

the box next to “Natural gas” and mark through “LP -

Propane.”

In the last page of the Use and Care Guide, write “Converted to

Natural Gas.” Also record the conversion date and the technician/

company that performed the conversion.

NOTE: Place LP gas parts in plastic parts bag for future use and

keep with pack containing literature.

Adjust High Flame Setting Screw

When converting from LP to Natural gas, you will need to adjust

the high flame setting screw for ideal burner flame height.

1. Pull out each control knob for the main burner and side burner.

2. Use a flat-blade screwdriver to turn the high flame setscrew

counterclockwise approximate 90°.

3. Check that burner operates at the new high flame setting. It

may be necessary to adjust the screw setting slightly more to

get the ideal burner flame height.

A. Orifice

A

A. Closed valve

B. Open valve

A

B

18

Check and Adjust the Burners

The burners are tested and factory-set for most efficient

operation. However, variations in gas supply and other conditions

may make minor adjustments to air shutter or low flame setting

necessary.

It is recommended that a qualified person make burner

adjustments.

NOTE: The rotisserie burner cannot be adjusted.

Checking and adjusting the grill burner flames requires removing

the grates and flame tamers.

Burner Flame Characteristics

The flames of the grill burners and side burners (on some models)

should be blue and stable with no excessive noise or lifting (LP

gas flames will have a slightly yellow tip). A yellow flame indicates

not enough air. If flame is noisy or lifts away from the burner, there

is too much air. Some yellow tips on flames when the burner is set

to HIGH setting are acceptable as long as no carbon or soot

deposits appear. The flames should be approximately 1" (2.5 cm)

high.

Check that burners are not blocked by dirt, debris, insect nests,

etc., and clean burners as necessary. If they are clean, adjust air

shutters as needed.

IMPORTANT: Before adjusting air shutters, let burners cool

completely.

To Adjust:

1. Light grill using information in the “Outdoor Grill Use” section.

2. Observe flame to determine which burners need adjustment

and how the flame is acting.

3. Turn off the valve and wait until grill and burners cool

completely.

4. Remove grill grates and flame tamers.

5. Remove the screw and cotter clip that hold the burner in

place. Remove gas burner from the grill.

6. If flame is yellow (not enough air), turn air shutter adjustment

screw counterclockwise.

If flame is noisy or lifts away from burner (too much air), turn

air shutter adjustment screw clockwise.

Adjustment should be made clockwise or counterclockwise

from 1/8" (3.2 mm) to 1/4" (6.4 mm).

7. Replace gas burner, flame tamers and grates.

8. Light grill using information in the “Outdoor Grill Use” section.

See “Burner Flame Characteristics.”

Low Flame Adjustment

If flame goes out on the “LOW” setting, the low flame setting must

be adjusted.

1. Turn off the valve and wait until grill and burners are cool.

2. Remove grill grates and flame tamers.

3. Light grill using information in the “Outdoor Grill Use” section.

4. Turn burner to its lowest setting.

5. Pull out each control knob for the main burner and side

burner.

6. Hold valve stem with pliers and insert a small flat-blade

screwdriver into the shaft.

7. Watch the flame and slowly turn the screwdriver

counterclockwise.

8. Adjust flame to minimum stable flame.

9. Replace the control knob and turn off the burner.

10. Repeat steps 3 through 9 for each burner if needed.

11. Replace the flame tamers and grates after the burners have

cooled.

A. Clip

1" (2.5 cm)

A

A. Air shutter adjustment screw

A. Valve stem

B. Small flat-blade screwdriver

C. Pliers

A

B

C

19

OUTDOOR GRILL USE

This manual covers several different models. The grill you have purchased may have some or all of the features listed. The locations and

appearances of the features shown here may not match those of your model.

Control Panel

Using Your Outdoor Grill

Inspect the LP Gas Fuel Tank Supply Hose

Inspect the gas pressure regulator/hose assembly before each

use.

1. Open left-hand cabinet door.

2. Inspect the gas pressure regulator/hose assembly for cuts,

abrasions, or excessive wear.

3. If necessary, replace the gas pressure regulator/hose

assembly before using the grill.

Contact the dealer and use only replacement hoses specified

for use with the grill.

A. Left grill burner knob

B. Left-center grill burner knob

C. Right-center grill burner knob

D. Rotisserie burner knob

E. Right grill burner knob

F. Grill light switch

G. Control panel light switch

H. Searing side burner knob

E

D

C

BA

F

H

G

WARNING

Explosion Hazard

Do not store fuel tank in a garage or indoors.

Do not store grill with fuel tank in a garage or indoors.

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.

Doing so can result in death or fire.

A. Gas pressure regulator/hose assembly

WARNING

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

A

20

Prepare the Grill for Lighting

1. Open the hood completely. Do not light burners with the hood

closed.

2. Make sure control knobs are turned to OFF. The drip pan must

be in place and pushed all the way to the back.

Turn the Gas Supply On

1. For outdoor grills using a 20 lb LP gas fuel tank:

Slowly open the tank valve.

NOTE: If flow limiting device activates, your grill may not light.

If your grill does light, the flames will be low and will not heat

properly. Turn tank valve and all control knobs off and wait

30 seconds. After shutting off the tank, very slowly open tank

valve and wait 5 seconds before lighting.

2. For outdoor grills using gas supply source other than 20 lb LP

gas fuel tank:

Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

Lighting the Grill and Searing Side Burner

IMPORTANT: If burner does not light immediately, turn the burner

knob to OFF and wait 5 minutes before relighting.

1. Open the hood completely. Do not light burners with the hood

closed.

2. Do not lean over the grill.

3. Select the burner you want to light. Push in and turn the grill

burner control knob to IGNITE HIGH, while continuing to hold

it in.

4. You will hear the “snapping” sound of the spark. When burner

is lit, release the knob. Turn knob to desired setting.

5. Repeat for each of the other burners as needed.

IMPORTANT: If burner does not light immediately, turn the

burner knob to OFF and wait 5 minutes before relighting.

Manually Lighting the Grill and Searing Side Burner

1. Open the hood completely. Do not light burners with the hood

closed.

2. Do not lean over the grill.

3. Remove the manual lighting extension (see following

illustration) and attach a match to the split ring.

4. Strike the match to light it.

5. Guide the lit match under the grill grate.

6. Push in and turn the burner knob to IGNITE HIGH for the

burner closest to the lit match. The burner will light

immediately. When burner is lit, turn knob to desired setting.

7. Repeat steps 2 through 6 for each main burner.

8. Remove match and replace manual lighting extension on the

right side panel.

IMPORTANT:

If burner does not light immediately, turn the burner knob to OFF

and wait 5 minutes before relighting.

If any burners do not light after attempting to light them manually,

contact the Customer Service Center. See the “Assistance”

section.

Hood Lights

The grill must be plugged in for the hood lights to work. See “Plug

in Grill” in the “Freestanding Outdoor Grill Installation” section.

To Use:

Press the LIGHTS button on the control panel to turn the hood

lights on and off.

A. Drip pan

A. Closed valve

B. Open valve

A

B

Page is loading ...

KitchenAid 730-0732 Installation Instructions And Use & Care Manual

This manual is also suitable for

KitchenAid 730-0732 Installation Instructions And Use & Care Manual

in other languages

Related papers

Other documents