Simplicity 040530-01 User manual

OPERATOR’S MANUAL

STANDBY GENERATOR SYSTEM

80012659 Revision B

Standby Generator System 12kW

This generator is rated in accordance with UL (Underwriters Laboratories)

2200 (stationary engine generator assemblies) and CSA (Canadian Standards

Association) standard C22.2 No. 100-4 (motors and generators).

may be reproduced or transmitted in any form by any means

without the express written permission of Rheem Manufacturing Company.

2

Thank you for purchasing this quality-built Rheem / Ruud standby generator. We are pleased that you’ve placed your confidence in the

Rheem or Ruud brand. When operated and maintained according to the instructions in this manual, your Rheem / Ruud generator will

provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with standby generators and how to

avoid them. This product is only for use as an optional generator system which provides an alternate source of electric power and to

serve loads such as heating, refrigeration systems, and communication systems that, when stopped during any power outage, could

cause discomfort or inconvenience.

Save these original instructions for future reference.

This standby generator requires professional installation before use. Refer to the separate Installation manual for instructions on safe

installation procedures. Your installer should follow the instructions completely.

Where to Find Us

You never have to look far to find support and service for your standby generator equipment. Consult your Yellow Pages. There are

many Rheem and Ruud authorized service dealers who provide quality service. You can also contact Rheem/Ruud Customer Service by

phone at 877-369-9400.

Generator and engine model and serial numbers should be recorded in the installation manual.

DATE OF PURCHASE

GENERATOR

Model Number

Model Revision

Serial Number

ENGINE

3

Table of Contents

Safety Rules .................................................. 4

Important Safety Instructions ..................................... 4

Installation .................................................... 7

For the Home Owner ........................................... 7

For the Installing Dealer/Contractor ............................... 7

Owner Orientation.............................................. 8

Generator Location............................................. 9

Delivery Inspection ............................................ 10

Controls ..................................................... 11

Access Panels................................................ 12

System Control Panel.......................................... 14

Menu ....................................................... 15

General Set-Up Screen ........................................ 16

Control Panel Prompts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Operation.................................................... 18

Important Owner’s Considerations ............................... 18

Automatic Operation Seqence................................... 19

Setting Exercise Timer ......................................... 19

Optional Wireless Monitor (Sold Separately) ....................... 20

Maintenance ................................................. 23

Servicing the System .......................................... 23

Service Code Detection System ................................. 23

Maintenance Schedule......................................... 25

Generator Maintenance ........................................ 25

Battery ...................................................... 26

Engine Maintenance........................................... 27

Adjust Valve Lash ............................................. 27

Electronic Governor System .................................... 28

Engine Oil ................................................... 29

Service Air Cleaner............................................ 30

Fuel System Inspection and Maintenance ......................... 31

Service Spark Plugs ........................................... 32

Clean Air Cooling System and Oil Cooler Fins...................... 32

When Calling for Assistance .................................... 32

Storage ..................................................... 32

Troubleshooting .............................................. 34

Wireless Monitor Troubleshooting ................................ 35

Speciﬁcations ................................................ 36

4

Safety Rules

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and

batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE is used to address practices not related to

personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

Important Safety Instructions

The manufacturer cannot possibly anticipate every

possible circumstance that might involve a hazard. The

warnings in this manual, and the tags and decals affixed

to the unit are, therefore, not all-inclusive. If you use a

procedure, work method or operating technique that

the manufacturer does not specifically recommend, you

must satisfy yourself that it is safe for you and others. You

must also make sure that the procedure, work method or

operating technique that you choose does not render the

generator system unsafe.

WARNING The engine exhaust from this product contains

chemicals known to the State of California to cause cancer, birth

defects, or other reproductive harm.

WARNING Certain components in this product and related

accessories contain chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm. Wash

hands after handling.

Explosion

Fire

Electrical Shock

Rotating Parts

Hot Surface

Toxic Fumes

Chemical BurnExplosive PressureAuto Start

Lift Hazard

Read Manual

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors, ventilation

intakes, soffit vents, crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter inside or be drawn

into a potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/ recommendations. Smoke alarms cannot detect

carbon monoxide gas.

5

WARNING Unintentional sparking could cause fire or electric

shock resulting in death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING Storage batteries give off explosive hydrogen gas

during recharging.

Slightest spark will ignite hydrogen and

cause explosion, resulting in death or serious injury.

Battery electrolyte fluid contains acid and is extremely caustic.

Contact with battery contents could cause severe chemical

burns. A battery presents a risk of electrical shock and high short

circuit current.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber boots and

rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

WARNING Generator produces hazardous voltage.

Failure to properly ground generator could result

in electrocution.

Failure to isolate generator from utility

power could result in death or serious injury to electric

utility workers due to backfeed of electrical energy.

• When using generator for backup power, notify utility company.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce the risk of a shock hazard.

• DO NOT allow unqualified persons or children to operate or

service generator.

• In case of an accident caused by electrical shock, immediately

shut down the source of electrical power and contact the local

authorities. Avoid direct contact with the victim.

• Despite the safe design of the residential generator, operating

this equipment imprudently, neglecting its maintenance or being

careless could cause possible injury or death.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• Before performing any maintenance on the generator,

disconnect the battery cable indicated by a NEGATIVE, NEG or

(-) first. When finished, reconnect that cable last.

• After your system is installed, the generator may crank and start

without warning any time there is a power failure. To prevent

possible injury, always set the generator’s system switch to

OFF, remove the service disconnect from the disconnect

box AND remove the 15 Amp fuse BEFORE working on the

equipment.

WARNING Propane and Natural Gas are extremely

flammable and explosive, which could cause

burns, fire or explosion resulting in death or

serious injury.

• Install the fuel supply system according to NFPA 37 and other

applicable fuel-gas codes.

• Before placing the generator into service, the fuel system lines

must be properly purged and leak tested.

• After the generator is installed, you should inspect the fuel

system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or other

explosive conditions exist.

• DO NOT smoke around the generator. Wipe up any oil spills

immediately. Ensure that no combustible materials are left in

the generator compartment. Keep the area near the generator

clean and free of debris.

6

WARNING Starter and other rotating parts could entangle

hands, hair, clothing, or accessories resulting in

serious injury.

• NEVER operate generator without protective housings, covers,

or guards in place.

• DO NOT wear loose clothing, jewelry or anything that could be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control panel and

disconnect Negative (NEG or -) battery cable.

CAUTION Installing the 15 Amp fuse could cause the engine

to start at any time without warning resulting in minor or

moderate injury.

• Observe that the 15 Amp fuse has been removed from the

control panel for shipping.

• DO NOT install this fuse until all plumbing and wiring has been

completed and inspected.

CAUTION Excessively high operating speeds could result in

minor injury.

Excessively low speeds impose a heavy load on generator.

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

NOTICE Improper treatment of generator could damage it and

shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact your

authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating air is

critical for correct generator operation.

• The access panels/door must be installed whenever the unit

is running.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner

cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a step.

Stepping on the unit could cause stress and break parts. This

may result in dangerous operating conditions from leaking

exhaust gases, fuel leakage, oil leakage, etc.

• If connected devices overheat, turn them off and disconnect

them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

-unit makes unusual noises.

WARNING Exhaust heat/gases could ignite combustibles or

structures resulting in death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must have at least

5 ft (1.5 m) minimum clearance from any structure, shrubs, trees

or any kind of vegetation.

• Standby generator weatherproof enclosure must be at least 5

ft from windows, doors, any wall opening, shrubs or vegetation

over 12 inches (30.48 cm) in height.

• Standby generator weatherproof enclosure must have a

minimum of 5 ft (1.5 m) overhead clearance from any structure,

overhang or trees.

• DO NOT place weatherproof enclosure under a deck or other

type of structure that may confine airflow.

• USE ONLY flexible steel fuel line provided. Connect provided

fuel line to generator, DO NOT use with or substitute any other

flexible fuel line.

• Smoke detector(s) MUST be installed and maintained indoors

according to the manufacturer’s instructions/ recommendations.

Carbon monoxide alarms cannot detect smoke.

• Keep at least minimum distances shown in Generator

Placement to insure for proper generator cooling and

maintenance clearances.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

7

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand Owner Orientation in

this manual before contracting or starting your

generator installation.

To arrange for proper installation, contact the store at

which you purchased your generator, your dealer, a

licensed electrician or your utility power provider.

The generator warranty is VOID unless the system

is installed by licensed electrical and plumbing

professionals.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter, or otherwise improve the product

and this document at any time without prior notice.

The Emission Control System for this generator is

warranted to standards set by the U.S. Environmental

Protection Agency and by the California Air Resources

Board (CARB).

For the Home Owner

If you need more information in this matter, please call

888 575‑8226 between 8:00 AM and 5:00 PM CT.

For most applications, the installation manual contains

all the information required to properly install and start

the generator. This operator’s manual describes routine

operation and owner maintenance procedures.

For the Installing Dealer/Contractor

Installation

We sincerely appreciate your patronage. For this reason, we

have made every effort to provide for a safe, streamlined and

cost-effective installation. Because each installation is unique, it

is impossible to know of and advise the trade of all conceivable

procedures and methods by which installation might be

achieved. Neither could we know of possible hazards and/or

the results of each method or procedure. For these reasons,

Only current licensed electrical and plumbing

professionals should attempt home generator system

installations. Installations must strictly comply with all

applicable codes, industry standards and regulations.

Your home generator is supplied with this “Operator’s

Manual” and a separate “Installation Manual”. These are

important documents and should be retained by the owner

after the installation has been completed.

This product is only for use as an optional generator system

which provides an alternate source of electric power and

to serve loads such as heating, refrigeration systems, and

communication systems that, when stopped during any

power outage, could cause discomfort or inconvenience.

NOTICE This product does NOT qualify for either an

emergency standby or legally required standby system as

defined by NFPA 70 (NEC).

• Emergency generator systems are intended to

automatically supply illumination, power, or both,

to designated areas and equipment in the event of

failure of the normal supply. Emergency systems

may also provide power for such functions as

ventilation where essential to maintain life, where

current interruption of the normal supply would

produce serious life safety or health hazards.

• Legally Required standby generator systems are

intended to automatically supply power to selected

loads in the event of failure of the normal source

which could create hazards or hamper rescue or

fire-fighting operations.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter, or otherwise improve the product

and this document at any time without prior notice.

Only current licensed electrical and plumbing professionals

should attempt home generator system installations.

Installations must strictly comply with all applicable codes,

industry standards, laws and regulations.

8

Power Decrease at High Altitude or

High Temperature

Air density is less at high altitudes, resulting in less

available engine power. Specifically, engine power will

decrease 3.5% for each 1,000 feet (300 meters) above sea

level and 1% for each 10° F (5.6°C) above 77°F (25°C).

Make sure you and your installer consider these factors

when determining total generator load.

existing electrical service and gaseous fuel supply

increases, and the number of 90 degree bends in the fuel

supply increases; compensations in piping and wiring

materials must be made. This is necessary to comply with

local codes and overcome electrical voltage drops and

gaseous fuel pressure drops.

The factors mentioned above will have a direct affect

on the overall price of your generator installation.

In some areas you may need to acquire electrical permits

for installing the home generator, building permits for

installing gas lines, and permits for noise allowances. Your

installer should check your local codes AND obtain the

permits before installing the system.

This section provides generator owners with the

information necessary to achieve the most satisfactory and

cost effective installation possible.

The illustrations are for typical circumstances and are

meant to familiarize you with the installation options

available with your generator. A thorough understanding

of these options will provide fundamental control over

the cost of your installation, as well as ensure your final

satisfaction and security.

Federal and local codes, appearance, noise levels,

fuel types, and distances are the factors that must

be considered when negotiating with an installation

professional. Remember that as the distance from the

Owner Orientation

9

The actual physical location of your home generator has a

direct affect on:

1. The amount of plumbing required to fuel

your generator.

2. The amount of wiring required to control and

connect your generator.

Specific location guidelines are discussed in the

installation manual. Acquaint yourself with that information

and confer with your installer. Be sure to ask how your site

might affect installation costs and compliance with local

codes and standards.

• Install generator outdoors in an area that will not

accumulate deadly exhaust gas.

• DO NOT install generator where exhaust gas could

accumulate and enter inside or be drawn into a

potentially occupied building or structure.

• By law it is required in many states to have a Carbon

Monoxide (CO) detector in operating condition in

your home. Carbon monoxide detector(s)

A

MUST

be installed and maintained indoors according to

the manufacturer’s instructions/ recommendations.

A CO monitor is an electronic device that detects

hazardous levels of CO. When there is a buildup of

CO, the monitor will alert the occupants by flashing

visual indicator light and alarm. Smoke alarms

cannot detect CO gas.

Generator Location

WARNING Exhaust heat/gases could ignite combustibles or

structures resulting in death or serious injury.

• Exhaust outlet side of weatherproof enclosure must have at least

5 ft (1.5 m) minimum clearance from any structure, shrubs, trees

or any kind of vegetation.

• Standby generator weatherproof enclosure must be at least

5 ft (1.5 m) from windows, doors, any wall opening, shrubs or

vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must have a

minimum of 5 ft (1.5 m) overhead clearance from any structure,

overhang or trees.

• DO NOT place weatherproof enclosure under a deck or other

type of structure that may confine airflow.

• USE ONLY flexible steel fuel line provided. Connect provided

fuel line to generator, DO NOT use with or substitute any other

flexible fuel line.

• Smoke detector(s) MUST be installed and maintained indoors

according to the manufacturer’s instructions/ recommendations.

Carbon monoxide alarms cannot detect smoke.

• DO NOT place weatherproof enclosure in manner other than

shown in illustrations.

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors, ventilation

intakes, soffit vents, crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter inside or be drawn

into a potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/ recommendations. Smoke alarms cannot detect

carbon monoxide gas.

• Ensure exhaust gas is kept away from any windows,

doors, ventilation intakes, soffit vents, crawl spaces,

open garage doors or other openings that can

allow exhaust gas to enter inside or be drawn into

a potentially occupied building or structure. Your

neighbor(s) home may be exposed to the engine

exhaust from your standby generator and must be

considered when installing your standby generator.

• Wind and air currents should be taken into

consideration when positioning generator.

See the installation manual for full details on safe

generator location.

A

10

Carefully inspect the home generator for any damage that

may have occurred during shipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight

bill and affix his signature under the consignor’s memo of

loss or damage. If loss or damage is noted after delivery,

separate the damaged materials and contact the carrier

and your installer for claim procedures. Parts damaged in

shipping are not warranted.

The home generator system is supplied with:

• Oil (5W30 Synthetic)

• Flexible steel fuel line

• Installation and start-up manual

• Operator’s manual

• Spare access door keys

• Spare 15 Amp ATO-type fuse

• Battery tie down strap

Not included:

• Carbon monoxide detector(s)

• Smoke detector(s)

• Starting battery

• Connecting wire and conduit

• Fuel supply valves/plumbing

• Crane, lifting straps, chains or cables

• Two 60” lengths of 3/4” nominal minimum scheduled

40 steel pipe (NOT conduit)

• Torque screwdriver, 5 to 70 inch-pound range

• Voltage/frequency meter

• Remote wireless monitor

• Antenna

• Two (2) AA batteries for remote wireless monitor

Delivery Inspection

11

MENU

ESC

AUTO OFF

MANUAL

Controls

12 kW Generator

A

B

C

D

E

F

G

H

J

Generator is shown with roof and access covers removed

for clarity.

- Lifting Holes — Provided at each corner for

lifting generator.

- Exhaust Port — High-performance muffler lowers

engine noise to comply with most residential codes.

- Alternator — An electrical machine that generates an

alternating current.

- Muffler — A device to reduce engine noise.

- Air Cleaner — Uses a dry type filter element to protect

engine by filtering dust and debris out of intake air.

- Control Panel — Used for various test, operation and

maintenance functions. See System Control Panel.

- Circuit Breaker — Protects the system from shorts and

other over-current conditions.

- Battery — (installer supplied) — 12 Volt DC, sealed

battery provides power to start the engine.

- Fuel Inlet Port — Attach appropriate fuel supply to

generator here.

A

B

C

D

E

F

G

H

J

12

Access Panels

The generator is equipped with an enclosure that has

several access panels, as shown.

Front Panel

A

and roof

B

are used to access:

• Battery Compartment

• Engine Oil Drain Hose

• Engine Oil Filter

• Engine Valve Cover

• Spark Plugs

Each generator is shipped with a set of identical keys.

A

B

13

To remove roof:

1. Remove the five screws

A

that secure the roof to

the unit.

2. Carefully lift and remove roof from unit.

To remove front panel:

1. Remove the two screws

B

that secure the panel to

the unit.

2. Lift and flex panel outward and off base. Use caution

not to damage the battery box

C

.

To secure front panel:

1. Place panel in unit.

2. Secure the panel with two screws.

A

C

B

14

System Control Panel

The generator control board, located inside the generator,

under the roof, is shown below. Brief descriptions of the

controls used during installation are:

A

- Menu/Programming Navigation Buttons — See

Menu section for details

B

- USB Port — Authorized Dealer Service Use Only.

C

- Generator Operation Control Buttons —

• “AUTO” Normal operating position. Press and hold

button to put unit into Automatic mode. In Automatic

mode, if a utility power outage is sensed, the

system will start the generator. When utility power

is restored, auto lets the engine stabilize internal

temperatures, shuts o the generator, and waits for

the next utility outage.

• “OFF” Turns o running generator and resets any

detected service codes.

OFF must be pressed and held for more than 5 seconds in

order to reset service code.

•“MANUAL” Used to manually start the generator.

D

– 15 Amp Fuse — Protects the home generator DC

control circuits. If the fuse has ‘blown’ (melted open)

or was removed, the engine cannot crank or start.

Replace the fuse using only an identical ATO 15A

fuse. One spare fuse is supplied with the unit.

E

- Cover — This protective cover must be opened to

access the fuse and the USB port.

F

- Digital Display — Displays generator mode,

menu options, service codes, and service engine

indicators

More information may be found in Controls in the

operator’s manual.

MENU

ESC

AUTO OFF

MANUAL

A

B

C

D

F

E

15

Menu

MENU

ENTER THE MENU (VIEW SETTINGS)

PRESS TO CONFIRM SELECTION WHEN PROGRAMMING.

ESCAPE (EXIT)

RETURN TO LAST MENU ITEM

RIGHT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

LEFT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

MANUAL MODE

USED TO MANUALLY START THE GENERATOR. PRESS AND HOLD BUT-

TON TO START THE GENERATOR.

OFF

TURNS OFF RUNNING GENERATOR, PREVENTS UNIT FROM STARTING,

AND RESETS ANY DETECTED SERVICE CODES.

AUTOMATIC MODE

NORMAL OPERATING POSITION. PRESS AND HOLD BUTTON TO PUT UNIT

INTO

AUTOMATIC MODE. IF A UTILITY POWER OUTAGE IS SENSED, THE

SYSTEM WILL START THE GENERATOR. WHEN UTILITY POWER IS RE-

STORED, AUTO LETS THE ENGINE STABILIZE INTERNAL TEMPERATURES,

SHUTS OFF THE GENERATOR, AND WAITS FOR THE NEXT UTILITY POW-

ER OUTAGE.

GENERAL

SET-UP

PRESS AND HOLD [ARROW LEFT AND ARROW RIGHT]

UNTIL “GENERAL SET-UP” IS DISPLAYED TO ENTER THE

PROGRAM MODE.

WIRELESS

LINK MODE

PRESS AND HOLD [MENU AND ESC] FOR THREE SEC-

ONDS TO ENTER THE WIRELESS LINKING MODE. (ONLY

APPLICABLE ON CERTAIN MODELS).

The following chart shows the icons for the buttons that control the system control panel.

The following chart describes key sequences for accessing different programming modes;

16

General Set Up Screen

NOTE: Date and Time were set at the factory and stored in the control panel memory. The Exercise Cycle was

also set at the factory. The default exercise cycle occurs on Tuesdays, at 2:00 P.M. Central Standard Time.

To updated or change these settings, follow the steps below.

IF DURING PROGRAMMING NO BUTTONS ARE PRESSED FOR 40 SECONDS,

THE CONTROL PANEL WILL AUTOMATICALLY EXIT THE PROGRAM MODE.

SET DATE

MONTH

FLASHING

DAY##

FLASHING

YEAR

FLASHING

“GENERAL SET-UP”

WILL SCROLL

SET TIME

HOURS

FLASHING

MIN

FLASHING

SET EXERCISE

CYCLE

AM/PM

FLASHING

HOURS

FLASHING

MIN

FLASHING

DAY OF WEEK

FLASHING

AM/PM

FLASHING

EVENT

LOG

Display will scroll last service code event, date, time, and

temperature of when the event occured.

or

OFF

If set to OFF, display will read: EXERCISE CYCLE OFF

or

or or or

or

or or or or

or or

For general set up, press and hold the left arrow and right arrow until “General Set-Up” is displayed. Follow the

prompts as outlined below.

ok

17

Control Panel Prompts

Automatic Mode

In Automatic Mode, the display screen will display via

scrolling text:

• GENERATOR READY - if the unit is in standby and

utility power is present.

• GENERATOR ON - if the unit is running and utility

power is not on.

• SERVICE CODE - if a system service code has

been detected.

General System Parameters

To view general system parameters, press the MENU

button.

The following will scroll across the digital display and then

move to the next item:

• Run time (total hours the unit has run since

installation)

• Date

• Time

• Exercise Cycle date and start time

The user can press the LEFT ARROW or RIGHT ARROW

at any time to move to the next item.

The user can press ESCAPE to go back to GENERATOR

READY.

If no user inputs are made for 10 seconds after all the

items have been displayed, the control board will reset to

GENERATOR READY.

AUTOMATIC MODE

RUN TIME

DATE

TIME

EXERCISE CYCLE

SOFTWARE VERSION

GENERATOR ON

(When Generator Running - Auto Mode)

GENERATOR READY or SERVICE CODE DESCRIPTION

(When Generator NOT Running - Auto Mode)

(MENU)

or

AUTOMATIC MODE

RUN TIME

DATE

TIME

EXERCISE CYCLE

SOFTWARE VERSION

GENERATOR ON

(When Generator Running - Auto Mode)

GENERATOR READY or SERVICE CODE DESCRIPTION

(When Generator NOT Running - Auto Mode)

(MENU)

or

18

Operation

Battery

The installer must supply a rechargeable 12 volt

DC starting battery. See Battery in Final Installation

Considerations in the installation manual.

With the battery installed, all wiring to transfer switch and

home generator completed, utility power supplied to the

automatic transfer switch, and the unit in AUTO mode, the

battery receives a trickle charge while the engine is not

running. The trickle charge cannot be used to recharge a

battery that is completely discharged.

NOTICE A battery booster should never be used to quick

charge a low battery.

Engine Oil

The engine is shipped from the factory pre-run and filled

with synthetic oil (API SJ/CF 5W-30). This allows for

system operation in a wide range of temperature and

climate conditions. Before starting the engine, check oil

level as described in Maintenance.

NOTICE Any attempt to crank or start the engine before it has

been properly serviced with the recommended oil will result in

equipment failure.

• Damage to equipment resulting from failure to follow this

instruction will void engine and generator warranty.

Important Owner’s Considerations

WARNING Battery posts, terminals and related accessories

contain lead and lead compounds, chemicals known to the

State of California to cause cancer and reproductive harm. Wash

hands after handling.

15 Amp Fuse

The generator’s 15 Amp fuse is critical to correct system

operation. The 15 Amp fuse was removed at the factory.

Your installer will ensure the fuse is properly installed upon

completion of the installation.

19

Utility Voltage Pickup Sensor

This sensor monitors utility power voltage. When utility

voltage is restored above 80 percent of the nominal source

voltage, a time delay starts timing and the engine will go to

engine cool-down.

Engine Cool-down Timer

When utility power is sensed and the load transfers to the

utility source, the engine will go into a cool down period as

described below:

• If the generator has run for MORE than 5 minutes,

once the utility transfer occurs, the engine will

continue to run for about 1 minute before shutting

down.

• If the generator has run for LESS than 5 minutes,

once the utility transfer occurs, the engine will

continue to run until 5 minutes has elapsed before

shutting down.

The generator’s control board constantly monitors utility

voltage. Should utility voltage drop below a preset level, the

control board will signal the engine to crank and start.

When utility voltage is restored above a preset voltage

level, the engine is signaled to shut down.

The actual system operation is not adjustable and is

sequenced by sensors and timers on the control board,

as follows:

Utility Voltage Dropout Sensor

• This sensor monitors utility source voltage.

• If utility source voltage drops below about

70 percent of the nominal supply voltage, the

sensor energizes a 3 second timer. The timer is

used to ‘sense’ brown-outs.

• Once the timer has expired, the engine will crank

and start.

Automatic Operation Sequence

The generator is equipped with an exercise timer. During

the exercise period, the unit runs for approximately

20 minutes and then shuts down. Electrical load transfer

DOES NOT occur during the exercise cycle (unless an

utility power outage occurs).

The generator will only enter the exercise cycle if the

unit is in the AUTO mode and this exact procedure is

followed.

To set the exercise timer:

NOTICE The generator is set with a default exercise cycle

setting of Tuesday at 2:00 P.M, Central Time. To change the

cycle setting, proceed to the following steps:

1. Choose the day and time you want your generator to

exercise.

2. Press and hold the left and right arrow until “General

Set-Up” scrolls. See General Set-Up flow chart in

Menu Section.

3. Verify and/or set the time and date on the unit.

4. Go to the SET EXERCISE prompt and hit the “OK”

button.

NOTICE Items will flash until they are selected.

Setting Exercise Timer

SELECT DAY: Use the left or right arrow to toggle

through the days of the week, Once the day is

selected, hit the “OK” button.

SELECT HOUR: Use the left or right arrow to toggle

through between 1 and 12. Choose the hour of day

you want the generator to exercise then hit the “OK”

button.

SELECT MINUTE: Use the left of right arrow to

toggle between :00 and :59. Choose the minute of

the day you want the generator to exercise then hit

the “OK” button.

SELECT AM/PM: Use the left of right arrow to toggle

between AM and PM. Once chosen, hit the “OK”

button.

NOTICE During the weekly exercise cycle, the generator

will run for 20 minutes, but it will not supply power to the

home. During the exercise cycle, the in-home monitor will

continue blinking the GENERATOR READY green LED.

If you want to change the day and time the unit exercises,

simply perform the procedure again.

To turn off the generator exercise cycle, go to the OFF

selection within the day of the week menu and press OK.

The display will then scroll: EXERCISE CYCLE OFF.

20

Wireless Monitor (Sold Separately)

An optional battery-powered wireless monitor is available.

The monitor communicates wirelessly with the generator

control panel. The monitor may be placed in a suitable

location in the home. The system has a line-of-sight range

of about 200 feet, but this distance will decrease if the

signal has to pass through walls or other objects.

The wireless monitor communicates with the generator,

every 10 minutes and will display the status via a green or

red LED light on the front of the monitor.

Compare the illustration below with your monitor to

familiarize yourself with these important components.

• Generator Ready

A

- Green LED

• Generator Power

B

- Green LED

• Service Needed

C

- Red LED

• System Update

D

- Press for current system

update with generator.

• Service code descriptions

E

- Name and number

of flashes are listed on the backside of the wireless

monitor.

• Battery Access Cover

F

- Record the dealer name

and phone number on the label provided. Once

removed, two non-rechargeable AA batteries are

installed in the compartment

G

.

DEALER

NAME

DEALER

PHONE

generator power

service needed

generator ready

system update

generator systems

1 low battery voltage

2 low fluid level

3 under/over voltage

4 engine does not start

part #: 316196 fcc id: MCQ-XBS2C IC id: 1846A-XBS2C

5 low frequency

6 engine overspeed

7 high temperature

8 transfer switch

# of flashes service needed

A

B

C

D

E

G

F

Page is loading ...

Simplicity 040530-01 User manual

This manual is also suitable for

Simplicity 040530-01 User manual

in other languages

Related papers

Other documents