De Dietrich SFH955WE1 Owner's manual

Brand: De Dietrich

Model: SFH955WE1

Type: Owner's manual

This manual is also suitable for

SFH955XE1

De Dietrich SFH955WE1 is a high-quality dishwasher, part of the SlimFit range, which offers a variety of washing options to meet your needs. Its 13 place settings capacity makes it suitable for larger families and households. The SFH955WE1 features 5 washing programs, including an eco program for energy-efficient washing and a quick program for lightly soiled dishes. Additionally, the dishwasher has a half-load option, which allows you to wash a smaller load of dishes without wasting water and energy.

EN INSTALLATIONS MANUAL

Dishwasher

CONTENTS

1 / SAFETY INSTRUCTIONS

• Important warnings __________________________________________ 03

2 / INSTALLING YOUR DISHWASHER

• Free-standing appliances ____________________________________ 04

• Built-in appliances __________________________________________ 04

• Appliances built-in under a hob ________________________________ 05

• Levelling by adjusting the feet ________________________________ 05

• Installing the sound-proofing flap ______________________________ 05

• Connecting to the water supply ________________________________ 06

• Draining away the waste water ________________________________ 07

• Connecting to the electricity supply ____________________________ 08

Important :

Please read this instructions manual carefully so that you can comply with the ins-

tructions for installing and fitting your machine.

NB :

This instructions manual covers various models. There may be some slight differen-

ces between your appliance and the descriptions shown.

1 / SAFETY INSTRUCTIONS

• IMPORTANT WARNINGS

Important :

After unpacking your appliance, make sure that it has not suffered any damage during

transport. Never connect up a damaged appliance. If your appliance is damaged, please contact

your dealer.

Danger :

If your appliance operates incorrectly, disconnect it (pull out the plug) or switch off the

circuit concerned and close the water supply tap. Contact our After-Sales Service.

Important :

All the necessary electrical and plumbing work for installing the appliance must respec-

tively be carried out by a qualified electrician or plumber.

— Once you have installed your appliance, ensure that it is not resting on the power cable or the

water supply or drain hoses.

— The appliance must be kept disconnected from the mains supply throughout the whole instal-

lation process.

— Check that your appliance’s Earth circuit complies with the prevailing regulations.

— The electrical connection details on the manufacturer’s plate on your machine must match

those for the mains power supply.

Important :

For safety’s sake, do not leave your dishwasher’s door fully open after use.

If your dishwasher is being installed on a carpeted floor, ensure that the feet are set to leave

an air space under the appliance.

2 / INSTALLING YOUR DISHWASHER

Fig. 04

Fig. 03

You can use the top of the appliance as a

worktop.

NB:

Do not position your dishwasher too

close to a heat source; otherwise the trim

around the top could be damaged.

•

BUILT-IN APPLIANCES

•

FREE-STANDING APPLIANCES

•

Installation dimensions

By removing the appliance’s worktop you can

build in your appliance under an existing

worktop provided that the space conforms to

the dimensions on the sketch. (Fig. 01)

•

Building in your appliance under

a worktop

If you are building in your appliance under an

existing worktop:

— Remove the top of the appliance by unscre-

wing the two screws under the edge of the

top (Fig. 02).

— Remove the top by unclipping it from the

back of the appliance and pushing it a few cm

to move it (Fig. 03).

— Lift the top of your dishwasher to release it

(Fig. 03).

— Insert the dishwasher into its appropriate

space

— Adjust the height of the feet, if necessary

(please refer to the Section: “Levelling by

adjusting the feet”).

— Fasten your dishwasher to the kitchen work-

top with two screws under the front of the

plastic lip (Fig 04).

If your worktop is marble or a similar material,

you can fasten your dishwasher at the side

with two brackets (available from After-Sales

or your dealer).

You can also incorporate your appliance into

a vertical unit (raised above the ground).

Fig. 02

Screw

820 - 830

820 min

110 mn

595

600

570 min

570

Fig. 01

Fig. 06

2 / INSTALLING YOUR DISHWASHER

Danger :

If your worktop has a hob fitted above your dishwasher, you must fit thermal insulation

on top of your dishwasher. You can obtain an insulation panel from your dealer. Remember to

leave a space between the gas pipe and the top of your dishwasher.

• LEVELLING BY ADJUSTING THE FEET

• INSTALLING THE

SOUND-PROOFING FLAP

Ensure that your dishwasher is quite plumb

and stable and that it i9n the place where it

will be installed. The feet are adjustable. Use a

screwdriver to adjust them, if necessary, so

that the door closes and seals perfectly

(Fig.06).

Ensure that the dishwasher’s door closes cor-

rectly, without catching at the sides.

To improve the appliance’s sound-proofing,

fit the flap supplied with your dishwasher

(depending on the model):

① - Tilt your dishwasher backwards slightly

so that you can clip the sound-proofing flap to

the base of the plinth and ensure it is well clip-

ped at three points (the ends and the centre),

② - Adjust the flap’s height by cutting off one

or more strips manually after scoring the end

with a pair of scissors.

The flap must be in contact with the floor.

(Fig. 07).

①

②

Fig. 07

• APPLIANCES BUILT-IN UNDER A HOB

To improve the built-in appliance’s sound-

proofing, fit the sound-proofing seals (depen-

ding on the model). ( on Fig. 05)

If the recess is bigger, stick on seal using

the adhesives provided.

•

SOUND-PROOFING SEALS

Fig. 05

2 / INSTALLING YOUR DISHWASHER

• CONNECTING TO THE WATER SUPPLY

Fig. 08

Danger :

The symbol indicates that the hose

is fitted with an electrical device for cutting

off the water supply (depending on the

model). Do not leave this hose in water and

do not cut it.

NB:

Any connection to a water conduit

necessarily involves the risk of a leak occur-

ring, whatever the precautions taken.

Therefore, always close the water tap when

you are not using your machine.

This dishwasher can be supplied with cold

water or hot water up to a maximum of 60°C.

When supplying with hot water, check that

your original hose allows such connection

(red marking on the hose). However, we

recommend that you connect to the cold

water supply. Your appliance is fitted with a

supply hose 1.50m long.

Connect the hose to a tap with a threaded

end, diameter 20/27 (3/4" BSP).

Check that the water pressure does not

exceed the values below:

Flow rate: 10 L/min (1 L/min minimum)

Pressure: 1 to 10 bars (0.1 - 1 MPa) (Fig. 08)

If the water pressure is too high, please fit a

pressure regulator. Your Water department

will advise you of the water pressure in your

region.

Warning :

If you use a self-piercing tap, check

that there is sufficient water flow.

Check that the hose seal is present and that

the connection is tight. (Fig. 05)

Do not re-use any previously used hoses for

making the connection.

Avoid any kinks or constrictions in the hose,

which could prevent the water from passing or

slow down its flow, particularly when building

in the appliance under the worktop. (Fig. 9).

If the appliance is connected to new pipes or

pipes that have not been used for a certain

length of time, let the water run for a few minu-

tes before connecting the water hose to avoid

and deposits of sand or rust that could block

the water hose’s filter.

00..11-- 11 MMPPaa

11--1100 bbaarr

1100LL//mmiinn

Fig. 09

2 / INSTALLING YOUR DISHWASHER

• DRAINING AWAY THE WASTE WATER

Fig. 11

Fig. 12

You can connect the end of the drain hose to:

- A ventilated U-bend (Fig. 10) or

- A sink U-bend (Fig. 10) or

- The edge of the sink, using the special plastic

hook provided (depending on the model) (Fig. 12).

When connecting to a U-bend, you must remove

the flapper from the U-bend. Then fully install the

rubber end. If necessary, add a tightening collar

(Fig. 11).

NB :

Ensure that the drain hose is held in

place with a tie to avoid any potential flooding.

The drain connection must be 0.40m (minimum)

to 1m (maximum) above the floor (Fig. 10).

If necessary, you can increase the hose’s length

(up to 3m maximum). In this case, check that the

appliance drains correctly. The hose must rest

on the floor and only rise vertically close to the

drainage system.

For appliances installed in vertical units, the

drainage system must not rise higher than the

top of the appliance.

Important :

When fitting the hose, pull on it gradually

so as not to kink it. (Fig. 9)

Avoid any kinks or constrictions in the hose,

which could prevent the water from passing or

slow down its flow.

15 cm

maxi

Fig. 10

2 / INSTALLING YOUR DISHWASHER

The appliance must be at a standstill when

connecting to the electricity supply circuit.

Before connecting your appliance, ensure

that:

- The mains voltage indicated on the manufac-

turer’s plate on your machine (230V) matches

the voltage supplied by your installation.

- Your meter and the fuses can support the

current. A 16A fuse is the minimum require-

ment.

If you must connect your appliance to a diffe-

rent voltage from that indicated on your

machine, connect an appropriate transformer.

NB :

Use the services of a qualified electri-

cian to make the modifications and ensure

that your electrical installation complies with

the regulations.

This appliance must necessarily be connec-

ted directly to an earthed plug and socket.

In all cases, it must be connected in accor-

dance with the prevailing regulations in the

country concerned and any additional regula-

tions from the local electricity utility.

Warning :

The plug and socket must be accessi-

ble even after your appliance has been ins-

talled. The appliance must not be connected

via an extension lead, a multiple socket or an

electric time delay programmer. (Fig. 13)

We cannot be held responsible in the event

of an accident or an incident caused by the

lack of or a defective earthing system.

Your dishwasher complies with European

Directives 73/23/EEC (Low Voltage Directive)

and 89/336/EEC (Electromagnetic Compatibility)

as modified by Directive 93/68/EEC.

•

Replacing the power cable

Danger :

For your safety’s sake, this operation

must only be performed by the manufactu-

rer’s After-Sales Department or by someone

with similar qualifications in order to avoid

any risks.

•

Appliances delivered without a plug

Danger :

The wires in your appliance’s power

cable are coloured as follows:

- Green & Yellow Earth

- Blue Neutral

- Brown Live

If the cable’s colours do not match your plug,

proceed as follows:

The wire coloured green and yellow must be

connected to the connector in your plug mar-

ked with the letter E, the symbol or colou-

red green and yellow.

The blue-coloured wire must be connected to

the connector marked with the letter N or

coloured black.

The brown-coloured wire must be connected

to the connector marked with the letter L or

coloured red.

Fig. 13

• ELECTRICAL CONNECTION

FagorBrandt SAS, locataire-gérant – SAS au capital social de 20 000 000 euros RCS Nanterre 440 303 196.

Réf.B9271A-2/2-06/09

De Dietrich SFH955WE1 Owner's manual

Brand: De Dietrich

Model: SFH955WE1

Type: Owner's manual

This manual is also suitable for

SFH955XE1

Download PDF

report

De Dietrich SFH955WE1 Owner's manual

This manual is also suitable for

De Dietrich SFH955WE1 Owner's manual

Related papers

Other documents