Shure UR5 User manual

Brand: Shure

Model: UR5

Category: Receiver

Type: User manual

Shure UR5 is a portable wireless receiver that offers reliable wireless audio transmission for a variety of applications. With its compact design and easy setup, it's perfect for use with wireless microphones, instruments, and other audio sources. The UR5 features a sturdy metal chassis, a backlit LCD display for clear visibility in low-light conditions, and a range of up to 300 feet. It also has adjustable output level control and a built-in limiter to prevent distortion.

UR5

Printed in U.S.A.

27A14812 (Rev. 1)

Portable Wireless Receiver

WARNING!

LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE.

USE AS LOW A VOLUME AS POSSIBLE.

Over exposure to excessive sound levels can damage your ears resulting in permanent noise-induced

hearing loss (NIHL). Please use the following guidelines established by the Occupational Safety Health

Administration (OSHA) on maximum time exposure to sound pressure levels before hearing damage

occurs.

90 dB SPL

at 8 hours

95 dB SPL

at 4 hours

100 dB SPL

at 2 hours

105 dB SPL

at 1 hour

110 dB SPL

at ½ hour

115 dB SPL

at 15 minutes

120 dB SPL

Avoid or damage may occur

ADVERTENCIA

EL ESCUCHAR REPRODUCCIONES DE AUDIO A NIVELES EXCESIVOS DE VOLUMEN PUEDE

CAUSAR DAÑOS PERMANENTES AL OIDO. USE EL VOLUMEN MAS BAJO POSIBLE.

La exposición prolongada a niveles sonoros excesivamente intensos puede dañar los oídos y causar

una pérdida permanente del oído causada por ruidos. Respete los lineamientos dados a continuación,

los cuales fueron establecidos por la Administración de Salud y Seguridad Ocupacional (OSHA) de

los EE.UU. e indican el tiempo máximo que puede escucharse un nivel determinado de presión sono-

ra (SPL) antes de producirse daños al oído.

90 dB SPL

por 8 horas

95 dB SPL

por 4 horas

100 dB SPL

por 2 horas

105 dB SPL

por 1 hora

110 dB SPL

por 1/2 hora

115 dB SPL

por 15 minutos

120 dB SPL

Evítese por completo, puesto que puede

causar daños inmediatos

SAFETY PRECAUTIONS

The possible results of incorrect use are marked by one of the two symbols -

“WARNING” AND “CAUTION” - depending on the imminence of the danger and the

severity of the damage.

WARNING: Ignoring these warnings may cause severe injury or death as a result

of incorrect operation.

CAUTION: Ignoring these cautions may cause moderate injury or property damage

as a result of incorrect operation.

WARNING

• If water or other foreign objects enter the inside of the device, fire or electric shock

may result.

• Do not attempt to modify this product. Doing so could result in personal injury and/or

product failure.

CAUTION

• Never disassemble or modify the device, as failures may result.

• Do not subject to extreme force and do not pull on the cable or failures may result.

WARNING: This product contains a chemical known to the State of California to cause cancer and birth

defects or other reproductive harm

PRECAUCIONES DE SEGURIDAD

Los posibles resultados del uso incorrecto de este producto se denotan por medio de uno de

dos símbolos - “ADVERTENCIA” y “PRECAUCION” - según la inminencia del peligro y el grado

de severidad de los daños.

ADVERTENCIA: Si se pasan por alto estas advertencias se podría causar lesiones

graves o mortales como resultado del uso incorrecto.

PRECAUCION: Si se pasan por alto estas precauciones se podría causar lesiones mod-

eradas y daños a la propiedad como resultado del uso incorrecto.

ADVERTENCIA

• Si el agua u otros objetos extraños penetran el dispositivo, se podría causar un incendio o

sacudidas eléctricas.

• No intente modificar este producto. Hacerlo podría causar lesiones personales y/o la falla

del producto.

PRECAUCION

• Nunca desarme ni modifique el dispositivo, ya que esto podría causar fallas.

• No someta el aparato a fuerzas extremas ni tire de su cable, ya que esto podría causar

fallas.

Page is loading ...

General Description

Included Components

• UR5:PortableWirelessReceiver

• 1/4WaveAntennas(2)

• TA3FtoXLRMAudioCable

• TA3Fto3.5mm(1/8”)AudioCable

• AABatteries(2)(exceptinArgentina)

• ShoeMount

• MountingStrap

• 90°SMAAdapters(2)

• ZipperedPouch

• ProtectiveCover

Features

• Wide-bandfrequencytuning

• Truediversity

• BalancedOutput

• Varietyofmountingoptions

• OperateswithstandardAAbatteriesorShureSB900rechargeablebattery

TheUR5isapremiumportablewirelessmicrophonereceivercomponent,designedtoprovideShureUHF-R®-classwirelesstechnology,performanceandqualityforprofes-

sionalfieldandmediaproductionapplications.Featuringwide-bandfrequencytuning,hands-onnavigation,rechargeability,andawidevarietyofmountingoptions,theUR5is

theclearestchoiceforwirelessportability.

Page is loading ...

UR5 Portable Receiver

① Power Switch

Turnstheportablereceiveronandoff.

② TA3M Jack.

Foraudioout.

③ 3.5 mm Headphone Jack

Formonitoringaudio.

④ Scan Button

Pressthescanbuttontofindthenextavailablechannel.Pressandholdfortwo

secondstofindthegroupwiththemostavailablechannels.

⑤ IR Window

FortransferringRFsettingsandnametoatransmitter,orcopyingtheMTxlistto

anotherreceiver.

⑥ Battery Compartment

Install2AAbatteriesoraShureSB900rechargeablebattery.Openbypressingthe

latchesonbothsidesandpullingoutward.

⑦ Menu Buttons

Useinconjunctionwiththe▼▲buttonstoaccesstheconfigurationmenus.

⑧ ▼▲ Buttons

Usetoscrollthroughmenus,changesettings,orselecttransmittersinMTxmode.

Canbeassignedtocontrolheadphoneorcameraoutputvolumes.

⑨ LCD Screen

Displayscurrentsettingsandmenus.

⑩ Tri-Color Battery LED

Illuminatesgreen,amber,orredtoindicatebatterypower.Whenred,change

batteriesimmediately.

⑪ Blue RF LED

Indicatestheportablereceiverisreceivingasignalfromthetransmitter.

⑫ Detachable Antennas (2)

SMAConnectors(2)

⑬ Power Through Contacts

ForpoweringthereceiverwheninsertedintotheShureAFP522DCcameramount.

Thereceiverautomaticallyswitchestointernalpowerwhenremovedfromthemount

orexternalpowerislost.

⑭ Removable AA Adapter

RemovetousewithaShureSB900rechargeablebattery.

Note:Toremoveadapter,opendoorandslideadapterout.Toreinstall,pressthe

adapterintoplace—thereisanaudibleclickwhenseated.

Power

TheUR5canbepoweredbyAAbatteries,aShureSB900rechargeablebattery,or

throughtheShureAFP522DCcameramount.

Standard AA Batteries

UsetheAAadapter(installedinthebatterycompartmentasshipped)whenusing

AAbatteries.

Forthebatteryicontoaccuratlydisplaybatterylife,selectthebatterytypefromthe

batterymenu(SYST CONF>BATTERY).

Note:Batterytypeissettoalkalinebydefault.

SB900 Rechargeable Battery Information

WhenusinganSB900rechargeablebattery,batterylifeisdisplayedinhours

andminutesonthehomescreen.Thebatterymenudisplaysbatterystatus:

SYST CONF > BATTERY

Hrs: Min Left:

Thenumberofhoursandminutesofbatterylifeleft(accurate

towithin15mins)

Health

Batteryhealthdisplayedasapercentage

Status

DisplayedaspercentagefullandmAh

Temperature

DisplayedinCelsiusandFahrenheit

Cycle Count

Displaysthenumberoftimesbatteryhasbeencharged

Battery Life

Battery Indicator Approximate Hours Remaining

LED Alkaline Li-ION

Green 2½–5 7–13

Green 2–2½ 5–7

Green 1½–2 3–5

Green 1–1½ 2–3

Amber ½–1 1–2

Red <½ <1

Note:Usinglower-impedanceearphones,differentbatterytypes,andhighergain

settingsmaycausethereceiverbatterylifetobedifferentthanspecified.

Audio

Audio Setup

Usethefollowingstepstoconnectthereceivertoacamera.Thesestepscanalso

beusedtoconnecttootherdevices,suchasfieldrecorders.

1. Adjustthetransmitteroutputlevelsothattheaudiolevelmeterbarsonthere-

ceiverarecloseto,butnotat,thepeaklevel(5thsegmentontheaudiobar).

2. Checktheinputsettingonthedevicetowhichyouareconnectingthere-

ceiver.Setthecameraoutputvolumeonthereceiveraccordingly(AUDIO>

CAMERA VOL).

Input Setting on the Camera UR5 Camera Output Volume

AUXlevel -5dB-+10dB)

MIClevel -36dB--5dB

3. AttachthesuppliedTA3Faudiocabletothereceivercameraoutput.

4. Mountthereceiveronthecamera.

5. Connectthecabletotheaudioinputonthecamera.

6. Adjustthecamerainputtothedesiredlevel.

Audio Settings

Usetheaudiomenu(AUDIO)toadjustcameraoutputlevelandheadphonevolume.

CAMERA VOL

Adjustscameraoutputleveltomatchtheinputlevelofthedevicetowhichyou

connectthereceiver.

HP VOLUME

Adjustsheadphonevolume.

HPO MODE

Disablescameraoutputandincreasesheadphontoutputgain.Assigns

▼▲buttonstoadjusttheoutputofheadphonevolume.ReturntoAUDIO

menutoexitHPOMODE.

Quick Access Volume Adjustment

Thereceivercanbeconfiguredsothatthe▼▲buttonsadjusttheoutputorhead-

phonevolume.Thisallowsyoueasilyadjustvolumewhilethereceiverismounted,

withouthavingtoentertheaudiomenu.

Note:ThissettingdoesnotapplywheninMTxmode.

UTILITIES > VOL. ASSIGN

CAMERA OUT

The▼▲buttonsadjustcameraoutputvolume.

HEADPHONE

The▼▲buttonsadjustheadphonevolume.

NONE(default)

The▼▲buttonsdonotaffectvolume.

Tone Generator

Accessthetonegeneratormenutosendatonetothecameraoutput(UTILITIES>

TONE GEN).Usethe▼▲buttonstoselecttonesof100Hz,1kHz,or5kHz.Exiting

turnsoffthetonegenerator.

Note:Audiofromthetransmitterisinterruptedwhileinthismenu.

SystemSetup

Scan and Sync

Usethisproceduretosetareceiverandtransmittertothesameopenchannel.

Important!Beforeyoubegin:

• TurnofftheRFonthetransmittersforthesystemsyouaresettingup.(This

preventsthemfrominterferingwiththefrequencyscan.)

• Turnonpotentialsourcesofinterferencesuchasotherwirelesssystemsor

devices,computers,CDplayers,largeLEDpanels,effectsprocessors,and

digitalrackequipmentsotheyareoperatingastheywouldbeduringthe

presentationorperformance(sothescanwilldetectandavoidanyinterference

theygenerate).

1. Performagroupscanonthereceiverbypressingandholdingthescanbutton

fortwo(2)seconds.GROUP SCANappearswhilethereceiverscansforthebest

groupoffrequenciesinyourRFenvironment.

2. Afterthescancompletes,thereceiverdisplaysthebestavailablefrequencyand

highlightstheSET FREQmenuitem.Pressentertoacceptthefrequencyand

returntothehomescreen.

3. Fromthereceiverhomescreen,pressentertogotothemainmenuandhigh-

lightSYNC.

4.

PowerontheselectedUHF-Rtransmitter,aligntheIRwindows,andpressenter

onthereceivertobeginthesync.

5. SYNCING…appearsontheLCD.Whencomplete,SUCCESSappearsandthe

LEDsonthereceiverflash.Thetransmitterandreceiverarenowtunedtothe

samefrequency.

Multiple System Setup

Whensettingupmultiplesystems,beginbysettingupthefirstsystemasfollows:

1. Conductagroupscanonthereceiverbypressingandholdingthescanbutton

fortwoseconds.

Notethegroupnumberandnumberofcompatiblefrequencies.

Pressentertoaccepttheselectedfrequency.

group

numberoffrequencies

Radio Frequency (RF) Settings

Transmitter Compatibility

ThereceiveriscompatiblewithbothUHF-RandAxienttransmitters,butmustbe

settothecorrectsystemmode.Selectthetransmittertypefromthesystemmode

menu(SYS MODE).Thisconfiguresthereceiverwithacompatibletonekey,au-

diocompanding,andIRsyncprotocol.TheUR5doesnothaveAxientShowLink

capabilities.

Note:ChangingmodesremovesallentriesintheMTxlist.Youwillbepromptedwith

thefollowingwarning:MTx MODE LIST WLL BE ERASED?.

System Mode Menu

SYST CONF > SYS MODE

UHF-R - CompatiblewithUHF-Rtransmitters.

Axient - CompatiblewithAxienttransmitters.

RF Pad

AccesstheRFpadmenu(RADIO>RF PAD)toattenuateantennasignallevelin1

dBincrements.

Scanning for an Open Channel

Ifyouexperienceinterference,useoneofthefollowingfrequencyscanstoanalyze

theRFenvironmentandidentifyanavailablefrequency.

• ChannelScan:Pressthescanbuttononthereceiver.Findsthefirstavailable

channel.

•

GroupScan:Pressandholdthescanbuttonfortwoseconds.Findsthegroup

withthegreatestnumberofavailablechannels.(Eachgroupcontainsasetof

frequenciesthatarecompatiblewhenoperatingmultiplesystemsinthesame

environment.)

•

FullScan:ScansthefullRFbandandallowsyoutoviewtheresultsina

graphicaldisplay.

Full Scan

ThisfeaturescanstheRFbandin25kHzincrementsforallavailablefrequencies,

firstwithantennaA,thenwithantennaB.Youcanthenviewagraphicaldisplayof

theresults.

1. Navigatetothefullscanmenu(RADIO>FULL SCAN)

2.

SelectRUN SCANandpressentertoinitiatethefullscan.

3. Oncethescaniscompleted,selectSPECTRUMfromthefullscanmenutoview

theresults.

Note:Ifthefullscanisinterrupted,nodataisstored,andNO DATAdisplaysonthe

screen.

Viewing Full Scan Results

Usethespectrummenutodisplayfullscanresults(RADIO>FULL SCAN>

SPECTRUM).

•

Acursorappearsasasmallarrowonthetopleftsideofthegraph.

• Usethe▼▲tomovethecursorleftorright

• PressthescanbuttontoviewthefrequencyanddBmatthecursorlocation.The

dBminformationisaccuratewithin+5dBbetween-100to-5dBm.

• Zoominandoutusingtheenterandexitbuttons.Thereareviews60MHz,9

MHz,or1MHzwide.

Toreturntothehomesreen,presstheexitbuttonrepeatedly.

Note:Thefullscanresultsareretainedinmemoryevenafterthereceiverispow-

eredoff.Foraccurateresults,performanewfullscaniftherearechangesinloca-

tionorRFenvironment.

2. Syncthereceiverwiththetransmitter.Leavethetransmitteron.

Repeatthefollowingstepsforeachadditionalsystem: 

1. Manuallysetthereceivertothedesignatedgroup.

2. Pressscanoncetofindthenextcompatiblefrequency.

3. Syncwithtransmitterandleavetransmitteronwhilesettingupadditional

systems.

Setting the Receiver to a Frequency from the

Spectrum View

1. Usethespectrummenutodisplayfullscanresults(RADIO>FULL SCAN>

SPECTRUM).

2.

Movethecursortothedesiredareaofthespectrum,usuallyonewiththeleast

amountofinterference.

3. Zoomintothe1MHz-wideviewusingtheenterbutton.

4. Pressscan.Thefrequencyisdisplayedwiththefollowingprompt:Enter to Set?.

5. Pressentertosetthereceivertothediplayedfrequencyandreturntothehome

screen.

Manual Frequency Selection

Tomanuallyadjustgroup,channelorfrequency,usetheRADIO>SET FREQ

menu.

Squelch

SquelchmutestheaudiooutputfromthereceiverwhenthetransmittertonekeyRF

signalbecomesloworinthepresenceofhighRFnoise.Whilesquelchisactivate,

theblueLEDontheportablereceiverturnsoff.

WARNING:AdjustingthesquelchcannegativelyaffectRFandaudioperformance.

UsethedefaultsettingHIGH (NORMAL)unlessabsolutelynecessary.

Squelch Settings

HIGH (NORMAL) Defaultfactorysetting.

MID Moderatelydecreasesthesignal-to-noiseratiore-

quiredtosquelchthereceiver.

LOW Greatlydecreasesthenoisesquelchthreshold.

HIGH NO TK* Highsquelchwithoutatonekey.

NO SQUELCH* Turnsoffnoiseandtonekeysquelch.(Usedasa

debuggingtoolbyengineersorRFcoordinatorsto

“listen”totheRFenvironment.)

*Symbolappearsindisplaywindow.

Other Settings

Receiver Label

Tochangethenamedisplayedonthehomescreen,usetheUTILITIES>RX NAME

menu.Usethe▼▲buttonstochangeeachcharacter.Pressthescanbuttontomove

thecursortothenextcharacter.Pressentertosavethename.

LCD Screen Display Settings

Home Screen

ChangetheappearanceoftheLCDfromthedisplaymenu(SYST CONF>

DISPLAY).

Usethe▼▲buttonstopreviewthedifferentwaysofdisplayinginformationonthe

homescreen.Pressentertoaccepttheselection.

Contrast

ChangethecontrastoftheLCDfromthecontrastmenu(SYST CONF>

CONTRAST).

Usethe▼▲buttonstosetthedesiredcontrast.

Lock Panel

LocksUR5Controls(UTILITIES>LOCK PANEL).

Selectandpressenter.

Restore

ResetsUR5tofactorydefaultparameters(SYST CONF>RESTORE).

Selectandpressenter.

Using Multiple Transmitters with a Single

Receiver (MTx Mode)

TheMTxfeaturestoresalistofpresets,allowingyoutoeasilyswitchfromone

transmittertoanotherwithouthavingtoreconfiguringreceiversettings.Thisreplac-

estheneedtomountmultiplereceiversonyourcamerawheneveryouonlyneedto

tunetoonetransmitteratatime.

ThepresetsarestoredasentriesintheMTxlist.Eachentrystoresaname,RF

channel,andreceivercameraoutputvolume.Transmitterscanbesyncedtoentries

inthelist,whichtransferstheentrynameandRFchannelsettingsovertheIRport.

Tousethepresets,enterMTxmodeonthereceiverandscrollthroughtheMTxlist

withthe▼▲buttonstoreceiveaudiofromthetransmitteronthatRFchannel.

MultipleentriescanbesettothesameRFchannel.Thismaybedesired,forexam-

ple,ifthesametransmitterwillbeusedatdifferenttimesthroughoutaperformance

atvaryingvolumes.

Entering MTx Mode

ToenterMTxmode,selectUTILITES>MTx MODE>ENTER MODE.Thename

andRFsettingsforthefirstentryintheMTxlistaredisplayed.

IftheMTxlistisempty,EMPTY LIST PRESS ENTER TO ADD

CURRENTSETTINGSisdiplayed.Pressentertocreateanewentrybasedonthe

currentreceiversettings.

Exiting MTx Mode

ToexitMTxmode,pressenterandselectEXIT MTx MODE.

Creating an MTx List

UseoneofthefollowingmethodstoaddentriestotheMTxlist.

Scan and Create

ThiscreatesanewMTxlistwithupto40entries.Eachentryisgivenan

auto-generatednameandassignedacompatibleRFchannel.

Whencreatinganewlist,allexistingentriesareoverwritten.

1. Performagroupscan(pressandholdscanbuttonfortwoseconds).

2. Afterthescancompletes,selectCREATE LIST

3. Thereceiverdisplaysthemaximumnumberofcompatiblechannelsavailablefor

theMTxlist.

Note:ThemaximumnumberforaMTxlistisforty(40).

4. Usethe▼▲buttonstochoosethenumberoftransmittersyouwanttoaddto

thelist.

5. Pressentertocreatethelist.

CREATING LIST…displayswhilethelistpopulates.Whencomplete,itdisplays

LIST DONEbeforereturningtothehomescreen.

Add Current

UsethismethodtoaddentriestotheMTxlistindividually,basedonthecurrentset-

tingsofthereceiver.

• Tunethereceivertothedesiredfrequency.Youmayalsowanttoadjustthe

recievercameraoutputlevel,asthisisalsostoredinthelistentry.

• SelectADD CURRENTfromtheMTxmenu(UTILITIES>MTx MODE>

ADD CURRENT)andpressenter.

SUCCESSisdisplayeduponcompletion.

LIST FULLdisplaysafterreachingthemaximumof40entries.

Copying an MTx List to Another Receiver

UseCOPY/PASTEtotransfertheMTxlistfromoneportablereceivertoanother.

1. HighlightCOPY/PASTEfromtheMTxmenuonbothreceivers(UTILITIES>

MTx MODE).

Important:COPY/PASTEmustbehighlightedonbothreceivers.

2. AlignthereceiverIRwindowsandpressenteronthesourcereceiver(there-

ceiveryouwanttocopyfrom).

ThedisplayshowsSUCCESSandtheLEDsflashonbothreceiversaftertrans-

ferringthelist.

Modifying an MTx List Entry

Thename,frequency,andcameraoutputvolumesettingcanbemodifiedforeach

entryinthelist.

1. EnterMTxmode(UTILITIES>MTxMODE>ENTER MODE).

2. Usethe▼▲buttonstoselectanentryfromthelist.

3. Pressentertoaccessthesubmenuforthatentry.

4. ScrolltotheMODIFYmenuitemandpressenter.

5. Chooseasettingtomodifyandpressenter.

6.

Pressexittocancelchangesorpressentertosavechangesandreturntohome

screen.

Transmitter Name

CLEAR?

Removescurrentname.

[NAME]

Changecharactersusingthe▼▲buttons,scanbuttontogotonextcharacter

.

Frequency

[000.000MHz]

PressentertoselectMHz,enteragaintoselectdecimalincrements.Changeusing

the▼▲buttons.

Camera Output Volume Setting

CAM. VOL.

Thisallowsyoutosetadifferentoutputvolumeforeachentry.Pressenterto

setthelevelofthecameraoutputofthereceiverwhentunedtotheselected

MTxlistentry.

Removing List Entries

Todeleteasingleentry:

1. EnterMTxmode(UTILITIES>MTxMODE>ENTER MODE).

2. Usethe▼▲buttonstoselectanentryfromthelist.

3. Pressentertoaccessthesubmenuforthatentry.

4. ScrolltotheDELETEmenuitemandpressenter.

Todeletetheentirelist:

1. AccesstheMTxmenu(UTILITIES>MTx MODE)

2.

ScrolltotheDELETE ALLmenuitemandpressenter.

SPECIFICATIONS

RF Carrier Range

470–952MHz(variesbyregion)

Modulation

FM,±45kHzmaximumdeviation

Antenna

RredictiveSwitchingDiversity

Dynamic Range

>100dBm=,A-weighted

RF Sensitivity

<-106dBm12dBSINAD,-88dBm30

dBSINAD

Spurious Rejection (ref.

12dB SINAD)

>80dB(typical)

Squelch Threshold

30dB SINAD(±3dB)normalsetting

Compatible Channels

Perband:40(banddependent)

Tuning Bandwidth

60–72MHz(banddependent)

Frequency Stability

±2.5ppm

Pilot Tone

UHF-RMode:32kHztonekeypilot

AxientMode:28kHztonekeypilot

Audio Frequency

Response

50Hz-16kHz

Ultimate Quieting

>100dBm=,A-weighted

Total Harmonic Distortion

(ref. ±20 kHz deviation @1

kHz)

<0.4%THD(typical)

Signal-To-Noise Ratio

(A-Weighted)

90dB(typical)

Companding

PatentedShureAudioReference

Companding

Camera Output

Electronicallybalanced

Configuration:mono

TA3Maximumoutputpower:adjustable

-35dBVto+10dBVpeak

PinAssignment:

Pin1=Gnd

Pin2=Hot

Pin3=Cold

Headphone Output

AdjustableRange

Configuration:Unbalancedmono

(L=R),1/8thinch

Minimumloadimpedance:9.5ohms

Impedance:3.5ohm

Maximumoutputpower:100mW

PinAssignment:

Tip=Hot

Ring=Hot

Sleeve-Gnd

Operating Temperature

-18°Cto+57°C(0°to+135°F)

Battery Life

4hoursAAAlkaline,8hoursShure

RechargeableLi-ion

Net Weight

200g(withAAbatteries)

Dimensions

83mmX65mmX22mm

Syncing Transmitters to the MTx List

AftercreatinganMTxlist,youcansynctransmitterstothelistentries.Whenyou

syncatransmittertoalistentry,ittransferstheRFsettingandnameofthatentryto

thetransmitter.

Note:

• Transmittersmustbefromthesamefrequencybandastheportablereceiver.

• SyncingwhileinMTxmodedoesnotchangeanyofthesettingsontheportable

receiver.

1. EnterMTxmode(UTILITIES>MTxMODE>ENTER MODE).

2. Usethe▼▲buttonstoselectanentryfromthelist.

3. Pressentertoaccessthesubmenuforthatentry.

4. HighlighttheSYNCmenuitem.

5. AlignthereceiverandtransmitterIRwindowsandpressentertobeginthesync.

ThescreendisplaysSYNC SUCCESSwhencompleted.

6. Repeatforeachtransmitterinthelist.

NOTE:

ThisRadioequipmentisintendedforuseinmusicalprofessionalentertainment

andsimilarapplications.

ThisRadioapparatusmaybecapableofoperatingonsomefrequenciesnot

authorizedinyourregion.Pleasecontactyournationalauthoritytoobtain

informationonauthorizedfrequenciesandRFpowerlevelsforwireless

microphoneproducts.

UR5 Frequency Bands - ABU/EMEA

FrequencyBand

Name

Range Freq.Span(MHz)

G1 470-530 60

G1E 470-530 60

H4 518-578 60

H4E 518-578 60

J5 578-638 60

J5E 578-638 60

J5HK 578-638 60

K4E 606-666 60

L3 638-698 60

L3E 638-698 60

M5E 694-758 64

P8 710-790 80

Q5 740-814 74

R9 790-865 75

R16 794-806 12

X1 944-952 8

UR5 Frequency Bands - SAL

FrequencyBand

Name

Range

Freq.Span(MHz)

H4 518-578 60

H4E 518-578 60

H4HK 518-565 47

J5E 578-638 60

L3E 638-698 60

P9 710-787 77

R9 790-865 75

R16 794-806 12

R18 794-806 12

MW5

FrequencyBand

Name

Range Freq.Span(MHz)

MABJ 779-810 31

X2 925-932 7

ACCESSORIES AND PARTS

Furnished Accessories

TA3F-to-XLRmaudiocable WA451

TA3F-to-1/8”(3.5mm)audiocable WA461

Camerashoemount AFP512

Optional Accessories

ShureRechargeableLithiumBattery SB900

Shure8-bayRechargingStation SBC800

AntonBauerplatemount AFP522

AntonBauerDCplatemount AFP522DC

Dimensions

22mm

65mm

83mm

CERTIFICATION

MeetsessentialrequirementsofthefollowingEuropeanDirectives:

• R&TTEDirective99/5/EC

• WEEEDirective2002/96/EC,asammendedby2008/34/EC

Pleasefollowyourregionalrecyclingschemeforelectronicwaste

• RoHSDirective2002/95/EC,asammendedby2008/35/EC

• ConformstoEuropeanRegulation(EC)No.1275/2008,asamended.

Meetsrequirementsofthefollowingstandards:EN300422Parts1and2,EN301

489Parts1and9,EN60065.

TheUR5wasconfirmedcomplaintbasedonuseofLR6AAalkalinebatteriesand

SB900batterypackasspecifiedintheinstructions.Useofotherbatterieswiththe

equipmenthasnotbeeninvestigated.Useofanyotherbatterycanresultinriskof

firehazards.

CertifiedinCanadabyICtoRSS-123.

IC:616A-UR5A,616A-UR5B,616A-UR5D,616A-UR5E

ApprovedundertheDeclarationofConformity(DoC)provisionofFCCPart15.

ThisdevicecomplieswithIndustryCanadalicence-exemptRSSstandard(s).

Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcause

interference,and(2)thisdevicemustacceptanyinterference,includinginterference

thatmaycauseundesiredoperationofthedevice.

LeprésentappareilestconformeauxCNRd’IndustrieCanadaapplicablesauxap-

pareilsradioexemptsdelicence.L’exploitationestautoriséeauxdeuxconditions

suivantes:(1)l’appareilnedoitpasproduiredebrouillage,et(2)l’utilisateurde

l’appareildoitacceptertoutbrouillageradioélectriquesubi,mêmesilebrouillageest

susceptibled’encompromettrelefonctionnement.

TheCEDeclarationofConformitycanbeobtainedfromShureIncorporatedorany

ofitsEuropeanrepresentatives.Forcontactinformationpleasevisitwww.shure.com

TheCEDeclarationofConformitycanbeobtainedfrom:

AuthorizedEuropeanrepresentative:

ShureEuropeGmbH

HeadquartersEurope,MiddleEast&Africa

Department:EMEAApproval

Jakob-Dieffenbacher-Str.12,

75031Eppingen,Germany

Phone:+49-7262-92490

Fax:+49-7262-9249114

Email:[email protected]

LICENSING INFORMATION

Licensing:Aministeriallicensetooperatethisequipmentmayberequiredincertain

areas.Consultyournationalauthorityforpossiblerequirements.Changesormodifi-

cationsnotexpresslyapprovedbyShureIncorporatedcouldvoidyourauthoritytoop-

eratetheequipment.LicensingofShurewirelessmicrophoneequipmentistheuser’s

responsibility,andlicensabilitydependsontheuser’sclassificationandapplication,

andontheselectedfrequency.Shurestronglyurgestheusertocontacttheappropri-

atetelecommunicationsauthorityconcerningproperlicensing,andbeforechoosing

andorderingfrequencies.

INFORMATION TO USER

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassB

digitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedto

providereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.

Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnot

installedandusedinaccordancewiththeinstructions,maycauseharmfulinterfer-

encetoradiocommunications.However,thereisnoguaranteethatinterferencewill

notoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterference

toradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoff

andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthe

followingmeasures:

• Relocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthe

receiverisconnected.

• Consultthedealer.

Note:EMCconformancetestingisbasedontheuseofsuppliedandrecommended

cabletypes.TheuseofothercabletypesmaydegradeEMCperformance.

Changesormodificationsnotexpresslyapprovedbythemanufacturercouldvoidthe

user’sauthoritytooperatetheequipment.

SYNC

AUDIO

HPO MODE

CAMERA VOL

HP VOLUME

UTILITIES

MTx MODE

ENTER MODE

ADD CURRENT

DELETE ALL

COPY/PASTE

VOL ASSIGN

TONE GEN

RX NAME

LOCK PANEL

SYST CONF

SYS MODE

DISPLAY

CONTRAST

BATTERY

RESTORE

SET MODE

UHFR

AXIENT

SET FREQ

SQUELCH

RF PAD

RUN SCAN

SPECTRUM

FULL SCAN

RADIO

exit

enter sync scan

exit

enter sync scan

www.shure.com

Asia, Pacific:

Shure Asia Limited

22/F, 625 King’s Road

North Point, Island East

Hong Kong

Phone: 852-2893-4290

Fax: 852-2893-4055

Email: [email protected]

United States, Canada, Latin

America, Caribbean:

Shure Incorporated

5800 West Touhy Avenue

Niles, IL 60714-4608 USA

Phone: 847-600-2000

Fax: 847-600-1212 (USA)

Fax: 847-600-6446

Email: [email protected]

Europe, Middle East, Africa:

Shure Europe GmbH

Jakob-Dieffenbacher-Str. 12,

75031 Eppingen, Germany

Phone: 49-7262-92490

Fax: 49-7262-9249114

Email: [email protected]

Shure UR5 User manual

Brand: Shure

Model: UR5

Category: Receiver

Type: User manual

Download PDF

report

Shure UR5 User manual

Shure UR5 User manual

Related papers

Other documents