Napa 85-303 User manual

Model 85-303

Professional Battery

Charger and Starter

INSTRUCTION MANUAL

English ................................................. p. 1

Français ................................................. p. 13

Español ................................................. p. 29

00-99-000802/0407

12 Volt

3 Amps

Page is loading ...

• 1 •

IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.

KEEP IT WITH OR NEAR THE CHARGER AT ALL TIMES.

NOTE: This device complies with Part 15 of the FCC Rules and Canadian Specica-

tion ICES-003. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interfer-

ence received, including interference that may cause undesired operation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment on and off, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio technician for help.

1. IMPORTANT SAFETY INSTRUCTIONS

WARNING—RISK OF EXPLOSIVE GASES

1.1 WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS

DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING

NORMAL BATTERY OPERATION, AND WHEN DISCHARGED OR

CHARGED. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE

THAT BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL

AND FOLLOW THE SAFETY AND OPERATING INSTRUCTIONS

EXACTLY.

1.2 To reduce risk of battery explosion, follow these safety instructions and

those published by the battery manufacturer and the manufacturer of any

equipment you intend to use in the vicinity of a battery. Review cautionary

markings on these products and on engine, and on vehicle or equipment

containing the battery.

1.3 CAUTION: To reduce the risk of injury, charge only rechargeable

LEAD-ACID-TYPE batteries which may include MAINTENANCE-

FREE, LOW-MAINTENANCE OR DEEP CYCLE batteries. Other types

of batteries may burst causing personal injury and damage.

If you are uncertain as to the type of battery you are attempting to charge,

or the correct procedure for checking the battery’s state of charge, contact

the seller or battery manufacturer.

1.4 Use of an attachment not recommended or sold by the battery charger

manufacturer may result in a risk of re, electric shock, or injury to

persons.

1.5 To reduce risk of damage to the electric plug and cord, pull by the plug

rather than the cord when disconnecting the charger.

• 2 •

1.6 Position the AC and DC leads to avoid tripping over them and to prevent

damage by the vehicle hood, doors, or moving engine parts; protect the

leads from heat, oil, and sharp edges.

1.7 Do not operate the charger if it has received a sharp blow, been dropped,

or otherwise damaged in any way; take it to a qualied service center.

1.8 Do not disassemble the charger; take it to a qualied service center when

repair is required. Incorrect reassembly may result in a risk of electric

shock or re.

The charger is not intended to supply power to a low-voltage electrical

system other than applications using rechargeable, lead-acid type

batteries. Do not use the battery charger to charge dry-cell batteries used

with home appliances. These batteries may burst and cause personal

injury or property damage.

1.9 NEVER charge a frozen battery. Thaw it out rst. Charging will then be

safer and more efcient.

1.10 To reduce risk of electric shock, unplug the charger from the AC outlet

before attempting any maintenance or cleaning. Turning off the controls

will not reduce this risk.

1.11 Boat batteries must be removed and charged on shore. To safely

charge them onboard requires equipment especially designed and

UL Listed for marine use.

1.12 Connect and disconnect the battery leads only when the AC supply cord is

disconnected.

1.13 Do not overcharge the battery.

1.14 When charging a battery, charge it in a dry, well-ventilated area.

1.15 Never place articles on or around the charger. Never locate the charger in

a way that will restrict the ow of cooling air through the cabinet.

1.16 An extension cord should not be used unless absolutely necessary. (See

paragraph 4.3.)

1.17 WARNING: THIS EQUIPMENT EMPLOYS PARTS, SUCH AS

SWITCHES AND CIRCUIT BREAKERS, THAT CAN PRODUCE ARCS

OR SPARKS. LOCATE THE CHARGER AT LEAST 46 CM (18 INCHES)

ABOVE GROUND LEVEL. IF USED IN A GARAGE, LOCATE IN A

ROOM OR ENCLOSURE PROVIDED FOR THE PURPOSE, AND NOT

LESS THAN 46 CM (18 INCHES) ABOVE FLOOR LEVEL.

1.18 WARNING: Handling the cord on this product or cords associated with

accessories sold with this product, may expose you to lead, a chemical

known to the State of California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

1.19 Have a damaged cord or plug replaced immediately.

1.20 Do not expose the charger to rain or snow.

• 3 •

2. PERSONAL PRECAUTIONS

2.1 Always have someone within range of your voice or close enough to come

to your aid, when working around lead-acid batteries.

2.2 Have plenty of fresh water and soap nearby in case battery acid contacts

skin, clothing, or eyes.

2.3 Wear complete eye protection, clothing protection, and rubber soled

shoes. When the ground is very wet or covered with snow, wear rubber

boots. Avoid touching eyes while working near the battery.

2.4 If battery acid contacts skin or clothing, wash immediately with soap and

water. If acid enters the eyes, immediately ush with running cold water for

at least 10 minutes and seek medical attention.

2.5 NEVER smoke or allow a spark or ame in vicinity of the battery or

engine.

2.6 Be extra cautious to reduce risk of dropping a metal tool onto the battery.

It might spark or short circuit the battery or other electrical part that may

cause an explosion.

2.7 Before working with a lead acid battery, remove personal metal items

such as rings, bracelets, necklaces, watches, etc. A lead acid battery can

produce a short circuit current high enough to weld such items, causing a

severe burn.

3. PREPARING TO CHARGE BATTERY

3.1 If necessary to remove the battery from the vehicle to charge, always

remove the grounded terminal from battery rst. Make sure all accessories

in the vehicle are off to prevent a possible arc.

3.2 Be sure the area around the battery is well ventilated while the battery

is being charged. Gas can be forcefully blown away by using a piece of

cardboard or other nonmetallic material as a fan.

3.3 Clean the battery terminals. Be careful to keep corrosion from coming into

contact with your eyes.

3.4 Add distilled water in each cell until the battery electrolyte reaches the

level specied by manufacturer. This helps purge excessive gas from

cells. Do not overll. For a battery without caps, carefully follow the

manufacturer’s recharging instructions.

3.5 Study all battery manufacturer’s specic precautions, such as removing or

not removing cell caps while charging, and recommended rates of charge.

3.6 Determine voltage of the battery by referring to the vehicle owner’s

manual, and make sure that the output voltage selector switch is set at the

correct voltage. If the charger has an adjustable charge rate, charge the

battery initially at lowest rate. If the charger has only one voltage, verify

that the battery voltage matches the voltage of charger. For a charger

• 4 •

not having an output voltage selector switch, determine the voltage of

the battery by referring to the vehicle owner’s manual and make sure it

matches the output rating of the battery charger.

4. AC POWER CORD CONNECTION INSTRUCTIONS

4.1 The charger must be grounded to reduce the risk of electric shock. The

charger is equipped with an electric cord having an equipment grounding

conductor and a grounding plug. The plug must be plugged into an outlet

that is properly installed and grounded in accordance with all local codes

and ordinances.

DANGER: NEVER ALTER CHARGER’S ORIGINAL AC CORD OR

PLUG. IF THE PLUG DOES NOT FIT OUTLET, HAVE PROPER

OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN. IMPROPER

CONNECTION CAN RESULT IN THE RISK OF AN ELECTRIC SHOCK.

DISCONNECT THE PLUG FROM OUTLET WHEN CHARGER IS IDLE.

4.2 This battery charger is for use on a nominal 120-volt circuit and has a

grounding plug that looks like the plug illustrated in Figure A. A temporary

adapter, which looks like the adapter illustrated in Figures B and C, may be

used to connect this plug to a two-pole receptacle as shown in Figure B, if

a properly grounded outlet is not available. The temporary adapter should

be used only until properly grounded outlet can be installed by a qualied

electrician.

DANGER: BEFORE USING AN ADAPTER AS ILLUSTRATED, BE

CERTAIN THAT THE CENTER SCREW OF THE OUTLET PLATE

IS GROUNDED (D). THE GREEN-COLORED RIGID EAR OR LUG

EXTENDING FROM ADAPTER MUST BE CONNECTED TO A

PROPERLY GROUNDED OUTLET. MAKE CERTAIN IT IS GROUNDED.

IF NECESSARY, REPLACE THE ORIGINAL OUTLET COVER PLATE

SCREW WITH A LONGER SCREW THAT WILL SECURE THE

ADAPTER EAR OR LUG TO THE COVER PLATE AND MAKE THE

GROUND CONNECTION TO THE GROUNDED OUTLET.

(D)

(A)

(C)

(B)

• 5 •

4.3 An extension cord should not be used unless absolutely necessary. Use of

an improper extension cord could result in a risk of re and electric shock.

If an extension cord must be used, make sure:

a. That the pins on the plug of extension cord are the same number, size,

and shape as those of the plug on charger;

b. That the extension cord is properly wired and in good electrical

condition;

c. That the wire size is large enough for AC ampere rating of the charger

as specied in the following table.

Recommended minimum AWG size for extension cords

for battery chargers

AC Input rating, Amps AWG size of cord

Equal to or

greater than

But less than

Length of cord, feet (m)

25 50 100 150

(7.6) (15.2) (30.5) (45.6)

0 2 18 18 16 16

2 4 18 16 12 10

4 6 16 14 10 8

6 8 16 12 10 8

8 10 14 12 8 6

10 12 14 12 8 6

12 14 14 10 8 6

5. CHARGER LOCATION

5.1 Locate the charger as far away from the battery as the charger cables

permit.

5.2 Never place the charger directly above the battery being charged; gases

from the battery will corrode and damage charger.

5.3 Never allow the electrolyte to drip on the charger when taking gravity

readings or lling a battery.

5.4 Operate the charger only in well ventilated area, free of dangerous vapors.

5.5 Store the charger in a safe, dry location and maintain it in perfect

condition.

5.6 Do not set the battery on top of charger or where acid might drip onto

charger.

• 6 •

6. DC CONNECTION PRECAUTIONS

6.1 All switches should be set in OFF (O) position and the AC cord should be

disconnected from the electrical outlet before you connect and disconnect

the charger clamps. Never allow the clamps to touch each other.

6.2 Attach clamps to battery posts and twist or rock back and forth several

times to make a good connection. This will tend to prevent the clamps

from slipping off terminals, avoid dangerous sparking, and assure safer

and more efcient charging. Keep the clamps clean.

CAUTION: SETTING SWITCHES TO OFF (O) DOES NOT ALWAYS

DISCONNECT THE CHARGER ELECTRICAL CIRCUIT FROM THE AC

POWER CORD OR DC CHARGER CLAMPS.

7. CHARGING BATTERY IN VEHICLE OR EQUIPMENT, OR CONNECTED

TO ENGINE

7.1 Before working on the vehicle, rmly apply the emergency brake and place

the gearshift to NEUTRAL. Shift an automatic transmission to PARK.

7.2 Locate the charger as far away from the battery as the charger cords

permit, and position the AC and DC cords to avoid stepping on or tripping

over them and to prevent damage by hood, doors, or moving engine parts.

7.3 Stay clear of fan blades, belts, pulleys, and any other parts that can cause

physical injury.

7.4 Turn OFF all vehicle loads, including door lights, and correct any defects

in vehicle’s electrical system that may have caused low battery.

7.5 Check the polarity of battery posts. The POSITIVE (POS., P, +) post

usually has larger diameter than NEGATIVE (NEG., N,–) post.

7.6 Determine which post of the battery is grounded (connected) to the

chassis. If the negative post is grounded (as in most vehicles), see

paragraph 7.7. If the positive post is grounded, see paragraph 7.8.

7.7 For a negative-grounded vehicle, rst connect the POSITIVE (red)

clamp from the charger to the POSITIVE (POS., P, +) ungrounded post

of battery. Then connect the NEGATIVE (BLACK) clamp to vehicle

chassis or engine block away from battery. Do not connect the clamp to

the carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy-

gauge metal part of the frame or engine block. When disconnecting the

charger, turn the switch to OFF (O), disconnect the AC cord, remove the

clamp from the vehicle chassis, and then remove the clamp from the

battery terminal.

7.8 For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clamp

from the charger to the NEGATIVE (NEG., N, –) ungrounded post of the

battery. Then connect the POSITIVE (RED) clamp to the vehicle chassis

or engine block away from the battery. Do not connect the clamp to the

carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy-

gauge metal part of the frame or engine block.

• 7 •

When disconnecting the charger, turn the switch to OFF (O), disconnect

the AC cord, remove the clamp from the vehicle chassis, and then remove

the clamp from the battery terminal.

CAUTION: WHEN THE POSITIVE (+) POST OF THE VEHICLE

BATTERY IS GROUNDED, DOUBLE-CHECK POLARITY.

8. CHARGING BATTERY OUTSIDE VEHICLE OR EQUIPMENT–NOT

CONNECTED TO ENGINE

If necessary to remove the battery from the vehicle or equipment, always

remove the grounded terminal from the battery rst.

WARNING: MAKE SURE ALL VEHICLE LOADS ARE OFF TO PREVENT

A POSSIBLE ARC.

FOLLOW THESE STEPS WHEN THE BATTERY IS OUTSIDE THE

VEHICLE. A SPARK NEAR BATTERY MAY CAUSE AN EXPLOSION. TO

REDUCE RISK:

8.1 Check the polarity of the battery posts. The POSITIVE (POS., P, +) post

usually has a larger diameter than the NEGATIVE (NEG., N, –) post.

8.2 Attach an insulated battery cable that is at least a 24-inch, 6-gauge to the

NEGATIVE (NEG., N, –) battery post.

8.3 Connect the POSITIVE (RED) charger clamp to the POSITIVE (POS.,

P, +) post of the battery.

8.4 Position yourself and the free end of cable as far away from the battery as

possible. Do not face the battery when making the nal connection. Then

connect the NEGATIVE (BLACK) charger clamp to the free end of the

cable.

8.5 When disconnecting the charger, always do so in the reverse sequence of

the connecting procedure. Break the rst connection while staying as far

away from the battery as practical.

8.6. A marine (boat) battery must be removed and charged on shore. To

charge it on board requires equipment specially designed for marine use.

• 8 •

9. ELECTRICAL CONDITION OF BATTERY

9.1 The state of charge of rellable-top batteries can be checked by using

a hydrometer. A hydrometer is a bulb-type syringe which is used to

extract a small quantity of the electrolyte from each battery cell. Types

are calibrated in terms of specic gravity (a common scale being 1.120

to 1.265) or the type which uses four colored balls to indicate the state of

charge. A oat in the hydrometer barrel indicates the specic gravity of

the electrolyte. This specic gravity reading indicates the battery’s state of

charge at a given temperature, as shown in the table below:

State of Charge of

Battery at 80°F (27°C)

** Initial Specic Gravity Reading

1.280 1.265 1.225 Floating Balls

100% 1.280 1.265 1.225 4

75% 1.240 1.225 1.185 3

50% 1.200 1.190 1.150 2

25% 1.170 1.155 1.115 1

Discharged 1.140 1.120 1.080 *

 **Initialspecicgravityreadingsvary,dependingonbatterytypeand

manufacturer.Contactthesellerormanufacturerofthebatteryforthis

specication.

 *Noballsoatinthebarrelofthehydrometer.

9.2 The state of charge of sealed-top (maintenance-free and recombination-

type) batteries must be checked with a high resolution voltage tester.

9.3 If uncertain about type of battery you will be charging, or the correct

procedure for checking the battery’s state of charge, contact the seller or

manufacturer of the battery.

9.4 The temperature of the battery and the equipment the battery is used

with has a dramatic effect on battery efciency and system power

requirements. For example, at 0°F (–18°C ), a battery is operating at 40%

of its rated efciency, while the engine it is attempting to start requires

over twice as much power as would be necessary at 80°F (27°C).

• 9 •

10. BATTERY CHARGING

10.1 This charger adjusts the charging time in order to charge the battery

completely, efciently and safely. However, this section includes

guidelines that can be used to estimate charging times.

10.2 The amount of time required to fully charge a weak battery is dependant

on a number of factors. In addition to the degree of discharge, these

factors include the type and rated capacity, temperature, age of the

battery, and amperage rating of the charger. At 70°F (22°C) the average

discharged battery will be recharged as follows.

Battery Charging Chart - Time

Battery Size - Amp Hours

(Ah) Reserve Capacity RC)

Charging Rate - Amps

2-4

amp

6-10

amp

15

amp

20

amp

40

amp

60

amp

Motorcycle/

Garden Tractor

Time to Charge Battery - Shown in Hours (hrs)

Small - (12-22 Ah) 2 hrs NR NR NR NR NR

Large - (22-35 Ah) 5

hrs

3.1

hrs

2.3

hrs

1.75

hrs

0.875

hrs

0.6

hrs

Automotive/Truck

(Groups 24, 27, 31, etc.)

Small -

(70-100 RC)

7.5

hrs

3.75

hrs

2

hrs

1.5

hrs

0.75

hrs

0.5

hrs

Medium -

(100-130 RC)

9

hrs

4.5

hrs

2.4

hrs

1.8

hrs

0.9

hrs

0.6

hrs

Large -

(130-160 RC)

12

hrs

6

hrs

3.2

hrs

2.4

hrs

1.2

hrs

0.8

hrs

Heavy Duty -

(160-190 RC)

15

hrs

7.5

hrs

4

hrs

3

hrs

1.5

hrs

1

hrs

Charging Times are based on a 50% discharged battery - approx

12-12.2 volts.

NR = Not Recommended.

Charging times will vary with battery type and condition.

10.3 Battery State – If a battery has only been slightly discharged, it can be

charged in less than a few hours. The same battery could take up to 10

hours if very weak. The battery state can be estimated by using the built-in

tester. The lower the reading the longer charging will take.

10.4. Battery rating – A higher rated battery will take longer to charge than

a lower rated battery under the same conditions. A battery is rated in

ampere-hours (AH), reserve capacity (RC) and cold cranking amps (CCA).

The lower the rating the quicker the battery will be charged.

•

• 10 •

10.5 CAUTION - Do not leave Manual chargers unattended.

10.6 CAUTION: If at any time the battery gets hot (above 125°F (52°C)) or acid

comes out of vent caps, STOP charging.

10.7 To maximize battery life - Let automatic chargers complete charging.

11. MULTIPLE BATTERY CHARGING

Batteries of the same voltage may be connected in parallel for

maintenance charging. Charge time increases in proportion to the number

of batteries. Rate of charge decreases in the same proportion.

Example: Charging 2 batteries in parallel will take 2 times longer; each

battery receives 1/2 the amount of charge showing on the ammeter. Thus,

if the ammeter shows a 30-amp charge, each battery will get a 15-amp

charge (when batteries have the same rating, same state of charge, etc.).

12. CHARGER FEATURES AND CONTROLS

12.1 The 85-303 does not have an ON/OFF switch. The On and Off commands

are controlled by plugging the 85-303 into a 120V AC electrical wall outlet

only after battery connections have been made.

LED Indicators

Charging Charged Check Battery*

*Indicates an overload condition caused by shorting of the battery clamps,

reverse polarity (hookup) connection to a battery, or charging a problem

battery.

• 11 •

12.2 Versatile Quick-Disconnect Harness

Snap any of the three connectors into place in seconds:

12.3 Battery Clamps

Connect the clamps to the charger. Refer to sections 7 and 8 to connect

the output clamps to the battery. After a solid electrical connection is

made to the battery, plug the power cord into a 120V AC electrical wall

outlet.

12.4 12V Accessory Plug

Charge or maintain your battery without lifting the hood. Connect the 12V

adapter to the charger and plug into the 12V accessory outlet. Route the

power cord from charger through the vehicle’s open window and plug into

a 120V AC electrical wall outlet. Make sure to place charger on a dry, non-

ammable surface, like metal or concrete.

12.5 Ring Connectors

The ring connectors permanently attach to the battery providing easy

access to quickly charge your battery. This application is appropriate for

motorcycles, lawn tractors, ATVs and snowmobiles. To permanently attach

to a battery, loosen and remove each nut from bolts at battery terminal.

Connect the red POSITIVE ring connector ring to the POSITIVE battery

terminal. Connect the black NEGATIVE connector ring to the NEGATIVE

battery terminal. Replace and tighten the nuts to secure. Take care to

keep both wires and plug away from metal and the engine hood. Plug the

power cord into a 120V AC electrical wall outlet.

13. MAINTENANCE INSTRUCTIONS

The charger is designed and built with high quality materials requiring only

a minimum amount of care.

13.1 Clamps should be cleaned each time the charger is used to prevent

corrosion from battery uid.

13.2 Cords should be coiled when the charger is not being used to prevent

damage.

13.3 Other servicing should be performed by qualied service personnel.

• 12 •

14. LIMITED WARRANTY

SCHUMACHER ELECTRIC CORPORATION, WARRANTS

EXCLUSIVELY TO THE ORIGINAL PURCHASER THAT THIS

CHARGER WILL BE REPAIRED OR REPLACED IF IT FAILS DURING

ITS LIMITED WARRANTY PERIOD OF TWO YEARS FROM DATE OF

RECEIPT DUE TO DEFECTS IN MATERIAL OR WORKMANSHIP. A

DATED SALES RECEIPT OR PROOF OF PURCHASE IS REQUIRED

FOR ALL CLAIMS.

This warranty does not cover failures arising out of improper use, abuse,

maintenance or operation of the product. This warranty does not cover

chargers that are opened or tampered with in any way.

Repair or replacement as provided under this warranty is the exclusive

remedy of the consumer. Schumacher Electric shall not be liable for any

incidental or consequential damages for breach of any express or implied

warranty on this product. Except to the extent provided by applicable law,

any implied warranty of merchantability or tness for a particular purpose

on this product is limited in duration to the warranty period.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, or allow limitation on how long as implied

warranty lasts, so the above limitations or exclusions may not apply to

you. This limited warranty gives you specic legal rights, and you may also

have other rights, which vary from state to state.

CUSTOMER SERVICE

For customer service (Monday through Friday), call:

1-888-263-4906, 7 a.m. to 4:30 p.m. (Central Time)

Return all products for warranty to your local NAPA Auto Parts Store.

• 13 •

Modèle 85-303

Chargeur de batterie

professionnel

MANUEL D’INSTRUCTIONS

English ................................................. p. 1

Français ................................................. p. 13

Español ................................................. p. 29

12 volts

3 ampères

Page is loading ...

• 19 •

4. INSTRUCTIONS DE BRANCHEMENT DU CORDON D’ALIMENTATION C.A.

4.1 Le chargeur doit être mis à la terre an de réduire les risques de choc

électrique. Le cordon d’alimentation du chargeur est muni d’un conducteur

de terre et d’une che avec mise à la terre. La che doit être branchée dans

une prise mise à la terre conformément aux codes d’électricité en vigueur.

DANGER : NE MODIFIEZ JAMAIS LE CORDON D’ALIMENTATION

C.A. OU LA FICHE DU CHARGEUR. SI LA FICHE NE S’ADAPTE PAS

À LA PRISE, FAITES INSTALLER UNE PRISE D’ALIMENTATION

C.A. AVEC MISE À LA TERRE PAR UN ÉLECTRICIEN QUALIFIÉ.

UNE MAUVAISE CONNEXION PEUT ENTRAÎNER DES RISQUES DE

CHOC ÉLECTRIQUE. RETIREZ LA FICHE DE LA PRISE LORSQUE LE

CHARGEUR EST AU REPOS.

4.2 Ce chargeur fonctionne sur un circuit nominal de 120 V et est muni d’une

che avec mise à la terre (référez-vous à l’illustration A). Si aucune prise

avec mise à la terre n’est disponible, vous pouvez utiliser un adaptateur, que

vous brancherez dans la prise bipolaire (référez-vous aux illustrations B et

C). Une telle installation doit être temporaire. Utilisez l’adaptateur jusqu’à ce

qu’une prise avec mise à la terre soit installée par un électricien qualié.

DANGER : AVANT D’UTILISER L’ADAPTATEUR TEL QU’IL EST

ILLUSTRÉ, ASSUREZ-VOUS QUE LA VIS CENTRALE DE LA PLAQUE

MURALE EST MISE À LA TERRE (D). LE CONNECTEUR VERT DE

L’ADAPTATEUR DOIT ÊTRE RELIÉ À UNE PRISE CORRECTEMENT

MISE À LA TERRE. ASSUREZ-VOUS QU’IL EST MIS À LA TERRE. AU

BESOIN, REMPLACEZ LA VIS DE LA PLAQUE PAR UNE VIS PLUS

LONGUE AFIN DE BIEN FIXER LE CONNECTEUR À LA PLAQUE

MURALE ET D’ASSURER UNE BONNE MISE À LA TERRE.

(D)

Page is loading ...

• 29 •

Modelo 85-303

Cargador/Arranque de

Baterías Profesional

MANUAL DE INSTRUCCIONES

English ................................................. p. 1

Français ................................................. p. 13

Español ................................................. p. 29

12 Voltios

3 Amperios

Page is loading ...

• 34 •

4. INSTRUCCIONES PARA CONECTAR EL CORDÓN DE POTENCIA CA

4.1 El cargador tiene que ponerse a tierra para evitar el riesgo de choque

eléctrico. El cargador viene equipado con un cordón eléctrico que posee

conductor para puesto a tierra de equipos y un enchufe para puesto a tierra.

El enchufe tiene que enchufarse en un tomacorriente debidamente instalado

y puesto a tierra de acuerdo con todos los códigos y ordenanzas locales.

PELIGRO: NUNCA ALTERE EL CORDÓN O ENCHUFE CA ORIGINAL

DEL CARGADOR. SI EL ENCHUFE NO ENTRA BIEN EN EL

TOMACORRIENTE, HAGA QUE UN ELECTRICISTA CALIFICADO

INSTALE UN TOMACORRIENTE APROPIADO. LA CONEXIÓN

INCORRECTA PUEDE RESULTAR EN RIESGO DE CHOQUE

ELÉCTRICO. DESCONECTE EL ENCHUFE DEL TOMACORRIENTE

CUANDO EL CARGADOR NO ESTÁ EN USO.

4.2 Este cargador es para usarse en un circuito nominal de 120 voltios y

tiene un enchufe de puesto a tierra parecido al enchufe ilustrado en la

Figura A. Un adaptador temporal, que se parece al adaptador ilustrado

en las Figuras B y C, puede usarse para conectar este enchufe en

un receptáculo de dos polos tal como se ve en la Figura B, si no hay

disponible un tomacorriente debidamente puesto a tierra. El adaptador

temporal debe usar únicamente hasta que un tomacorriente debidamente

puesto a tierra puede ser instalado por un electricista calicado.

PELIGRO: ANTES DE USAR UN ADAPTADOR COMO SE VE

EN LA ILUSTRACIÓN, ASEGÚRESE DE QUE EL TORNILLO

CENTRAL DE LA PLACA DE SALIDA ESTÉ PUESTO A TIERRA

(D). LA OREJA O LÓBULO DE COLOR VERDE, QUE SE EXTIENDE

DESDE EL ADAPTADOR, TIENE QUE ESTAR CONECTADO A

UN TOMACORRIENTE DEBIDAMENTE PUESTO A TIERRA.

ASEGÚRESE DE QUE SÍ ESTÉ PUESTO A TIERRA. AL SER

NECESARIO, REEMPLACE EL TORNILLO ORIGINAL DE LA PLACA

DE CUBIERTA DE SALIDA CON UN TORNILLO MÁS LARGO QUE

HA DE ASEGURAR LA OREJA O EL LÓBULO DEL ADAPTADOR A

LA PLACA DE CUBIERTA Y HACER LA CONEXIÓN A TIERRA AL

TOMACORRIENTE PUESTO A TIERRA.

(D)

Page is loading ...

Napa 85-303 User manual

Napa 85-303 User manual

in other languages

Related papers

Other documents