Electrolux EFC9690X User manual

Category
Cooker hoods
Type
User manual

This manual is also suitable for

EFC 6690 - EFC 9690
User manual
Manual de instrucciones
Manual de instruções
electroluxelectrolux
electroluxelectrolux
electrolux
safety warnings
33
33
3
GB
WW
WW
W
elcome to the world of Electrelcome to the world of Electr
elcome to the world of Electrelcome to the world of Electr
elcome to the world of Electr
oluxolux
oluxolux
olux
Thank you for choosing a first class
product from Electrolux, which
hopefully will provide you with lots of
pleasure in the future. The Electrolux
ambition is to offer a wide variety of
quality products that make your life
more comfortable. You find some
examples on the cover in this manual.
Please take a few minutes to study this
manual so that you can take advantage
of the benefits of your new machine.
We promise that it will provide a
superior User Experience delivering
Ease-of-Mind. Good luck!
44
44
4
electr electr
electr electr
electr
oluxolux
oluxolux
olux contents
GB
Contents
Safety warnings ................................5
Description of the Appliance ..............7
Control Panel ....................................8
Maintenance and Care ....................12
Special accessories ........................17
Something Not Working ..................17
Installation....................................... 18
The following symbols are used in this user manual:
Important information concerning your personal safety and information on
how to avoid damaging the appliance.
General information and tips.
Environmental information.
electroluxelectrolux
electroluxelectrolux
electrolux
safety warnings
55
55
5
GB
Safety warnings
For the userFor the user
For the userFor the user
For the user
The cooker hood is designed to
extract unpleasant odours from the
kitchen, it will not extract steam.
Always cover lighted elements, to
prevent excess heat from damaging
the appliance. In the case of oil, gas
and coal fired cookers it is essential
to avoid open flames.
Also, when frying, keep the deep
frying pan on the cooker top/cooker
under careful control.
The hot oil in the frying pan might
ignite due to overheating.
The risk of self-ignition increases
when the oil being used is dirty.
It is extremely important to note that
overheating can cause a fire.
Never carry out any flambé cookingNever carry out any flambé cooking
Never carry out any flambé cookingNever carry out any flambé cooking
Never carry out any flambé cooking
under the hood.under the hood.
under the hood.under the hood.
under the hood.
Always disconnect the unit frAlways disconnect the unit fr
Always disconnect the unit frAlways disconnect the unit fr
Always disconnect the unit fr
om theom the
om theom the
om the
power supply beforpower supply befor
power supply beforpower supply befor
power supply befor
e carrying oute carrying out
e carrying oute carrying out
e carrying out
any work on the hood, includingany work on the hood, including
any work on the hood, includingany work on the hood, including
any work on the hood, including
rr
rr
r
eplacing the light bulbeplacing the light bulb
eplacing the light bulbeplacing the light bulb
eplacing the light bulb (take the
cartridge fuse out of the fuse holder
or switch off the automatic circuit
breaker).
It is very important to clean the hoodIt is very important to clean the hood
It is very important to clean the hoodIt is very important to clean the hood
It is very important to clean the hood
and rand r
and rand r
and r
eplace the filter at theeplace the filter at the
eplace the filter at theeplace the filter at the
eplace the filter at the
rr
rr
r
ecommended intervals. Failurecommended intervals. Failur
ecommended intervals. Failurecommended intervals. Failur
ecommended intervals. Failur
e toe to
e toe to
e to
do so could cause grdo so could cause gr
do so could cause grdo so could cause gr
do so could cause gr
ease depositsease deposits
ease depositsease deposits
ease deposits
to build up, rto build up, r
to build up, rto build up, r
to build up, r
esulting in a firesulting in a fir
esulting in a firesulting in a fir
esulting in a fir
e hazare hazar
e hazare hazar
e hazar
d.d.
d.d.
d.
The appliance is not intended for use
by young children or infirm persons
without supervision.
Older children must be supervised if
using the appliance.
Young children should be supervised
to ensure that they do not play with
the appliance.
WW
WW
W
ARNING - ARNING -
ARNING - ARNING -
ARNING - Ensure that the
appliance is switched off before
replacing the lamp to avoid the
possibility of electric shock.
This appliance is marked according to
the European directive 2002/96/EC on
Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the
environment and human health, which
could otherwise be caused by
inappropriate waste handling of this
product.
The symbol on the product, or on
the documents accompanying the
product, indicates that this appliance
may not be treated as household
waste. Instead it shall be handed over
to the applicable collection point for the
recycling of electrical and electronic
equipment.
Disposal must be carried out in
accordance with local environmental
regulations for waste disposal.
For more detailed information about
treatment, recovery and recycling of
this product, please contact your local
city office, your household waste
disposal service or the shop where you
purchased the product.
66
66
6
electr electr
electr electr
electr
oluxolux
oluxolux
olux safety warnings
GB
For the installerFor the installer
For the installerFor the installer
For the installer
When used as an extractor unit, the
hood must be fitted with a hose
having preferably the same diameter
as the outlet hole.
Attention: Attention:
Attention: Attention:
Attention: The hose is not supplied
and must be purchased separately.
When installing the hood, make surWhen installing the hood, make sur
When installing the hood, make surWhen installing the hood, make sur
When installing the hood, make sur
ee
ee
e
you observe the following minimumyou observe the following minimum
you observe the following minimumyou observe the following minimum
you observe the following minimum
distance frdistance fr
distance frdistance fr
distance fr
om the top edge of theom the top edge of the
om the top edge of theom the top edge of the
om the top edge of the
cooking hob/ring surfaces:cooking hob/ring surfaces:
cooking hob/ring surfaces:cooking hob/ring surfaces:
cooking hob/ring surfaces:
electric cookerselectric cookers
electric cookerselectric cookers
electric cookers
500 mm500 mm
500 mm500 mm
500 mm
gas cookersgas cookers
gas cookersgas cookers
gas cookers
700 mm700 mm
700 mm700 mm
700 mm
If the instructions for installation for
the gas hob specify a greater
distance, this must be adhered to.
The national Standard on fuel-
burning systems specifies a maxi-
mum depression of 0.04 mbar in
such rooms.
The air outlet must not be connected
to chimney flues or combustion gas
ducts. The air outlet must under no
circumstances be connected to
ventilation ducts for rooms in which
fuel-burning appliances are installed.
The air outlet installation must comply
with the regulations laid down by the
relevant local authorities.
When the unit is used in extraction
mode, a sufficiently large ventilation
hole must be provided, with
dimensions that are approximately
the same as the outlet hole.
National and regional building
regulations impose a number of
restrictions on using hoods and fuel-
burning appliances connected to a
chimney, such as coal or oil room-
heaters and gas fires, in the same
room.
Hoods can only be used safely with
appliances connected to a chimney if
the room and/or flat (air/environment
combination) is ventilated from
outside using a suitable ventilation
hole approximately 500-600 cm
2
large to avoid the possibility of a
depression being created during
operation of the hood.
If you have any doubts, contact the
relevant controlling authority or
building inspector’s office.
Since the rule for rooms with fuel
burning appliances is “outlet hole of
the same size as the ventilation hole”,
a hole of 500-600 cm
2
, which is to
say a larger hole, could reduce the
performance of the extractor hood.
If the hood is used in its recirculation
mode, it will operate simply and safely
in the above conditions without the
need for any of the aforementioned
measures.
When the hood is used in its
extraction mode, the following rules
must be followed to obtain optimal
operation:
- short and straight outlet hose
- keep bends in outlet hose to a
minimum
- never install the hoses with an
acute angle, they must always
follow a gentle curve.
- keep the hose as large as possible
(preferably the same diameter as
the outlet hole).
- the length should be no more than:
3 metres with one 90° bend
2 metres with two 90° bends
Bends of more than 90° will reduce
the efficiency of the hood and
reduce the airflow.
Failure to observe these basic
instructions will drastically reduce the
performance and increase the noise
levels of the extractor hood.
electrolux electrolux
electrolux electrolux
electrolux description of the appliance
77
77
7
GB
Description of the Appliance
The hood is supplied exclusively for
functioning as a filtering version
apparatus.
The fumes and steam are aspirated,
filtered and returned into the kitchen.
• It is possible to purchase a
telescopic flue to convert the hood
from “filtering version hood” to
“aspiration version hood”, (see
“special accessories” chapter) and
therefore convey the steam and
smells outside.
88
88
8
electr electr
electr electr
electr
oluxolux
oluxolux
olux control panel
GB
Control Panel
Best results are obtained by using a low speed for normal conditions and a high
speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking.
The hood should be left on after cooking for about 15 minutes or until all the
odours have disappeared.
CorrCorr
CorrCorr
Corr
ect ventilation:ect ventilation:
ect ventilation:ect ventilation:
ect ventilation: If the cooker hood is to work correctly there must be an
under pressure in the kitchen. It is important to keep the kitchen windows
closed and have a window in an adjacent room open.
The hood is equipped with a
TOUCH SENSORTOUCH SENSOR
TOUCH SENSORTOUCH SENSOR
TOUCH SENSOR” device able to
determine the control of the lights
and the speed when the user
touches the control bar. Read the
instructions below carefully for this
purpose.
The hood is fitted with an electrThe hood is fitted with an electr
The hood is fitted with an electrThe hood is fitted with an electr
The hood is fitted with an electr
oniconic
oniconic
onic
overover
overover
over
-charge pr-charge pr
-charge pr-charge pr
-charge pr
otection system: inotection system: in
otection system: inotection system: in
otection system: in
the event of an excessive chargethe event of an excessive charge
the event of an excessive chargethe event of an excessive charge
the event of an excessive charge
on the mains supply network, theon the mains supply network, the
on the mains supply network, theon the mains supply network, the
on the mains supply network, the
electrelectr
electrelectr
electr
onic system goes intoonic system goes into
onic system goes intoonic system goes into
onic system goes into
prpr
prpr
pr
otective mode and the Neon lightotective mode and the Neon light
otective mode and the Neon lightotective mode and the Neon light
otective mode and the Neon light
switches ofswitches of
switches ofswitches of
switches of
f; to rf; to r
f; to rf; to r
f; to r
eset simply switcheset simply switch
eset simply switcheset simply switch
eset simply switch
ofof
ofof
of
f the Neon and then on againf the Neon and then on again
f the Neon and then on againf the Neon and then on again
f the Neon and then on again
using the hood contrusing the hood contr
using the hood contrusing the hood contr
using the hood contr
ol.ol.
ol.ol.
ol.
Automatic switch-on functionAutomatic switch-on function
Automatic switch-on functionAutomatic switch-on function
Automatic switch-on function
The hood is equipped with a tempera-
ture sensor that starts the motor at the
1st suction speed (power) when the
room temperature around the hood is
higher than 70°C.
The user can, however, switch off or
modify the suction speed (power). (See
paragraph “
ContrContr
ContrContr
Contr
ol of suction speedol of suction speed
ol of suction speedol of suction speed
ol of suction speed
(power)(power)
(power)(power)
(power)”).
electrolux electrolux
electrolux electrolux
electrolux control panel
99
99
9
GB
Control of suction speed (power)Control of suction speed (power)
Control of suction speed (power)Control of suction speed (power)
Control of suction speed (power)
The selection of the suction speed
(power) is cyclical, according to the
speed sequences “”stand-by - 1-2-3-
4- Stand by -1-2-”… so that at every
touch of the
UPPER PUPPER P
UPPER PUPPER P
UPPER P
ARAR
ARAR
ART of the
control bar the suction speed (power)
increases by a level and then switches
off (stand-by) if the control bar is
touched again when the hood is at
suction speed (power) 4.
It is possible to turn the hood off
(standby) even when the hood is at
any speed by pressing the
UPPERUPPER
UPPERUPPER
UPPER
PP
PP
P
ARAR
ARAR
AR
T T
T T
T of the control bar (for more than
3 seconds).
UPPER PUPPER P
UPPER PUPPER P
UPPER P
ARAR
ARAR
AR
TT
TT
T
LED
LOWER PLOWER P
LOWER PLOWER P
LOWER P
ARAR
ARAR
AR
TT
TT
T
ContrContr
ContrContr
Contr
ol barol bar
ol barol bar
ol bar
1010
1010
10
electr electr
electr electr
electr
oluxolux
oluxolux
olux control panel
GB
It is possible to determine what suction
speed (power) the hood is in when the
bar is equipped with a led that changes
colour on the basis of the suction
speed (power), as follows:
Hood in stand-by:
LED OFFLED OFF
LED OFFLED OFF
LED OFF
1st suction speed (power)
- led - led
- led - led
- led
GREENGREEN
GREENGREEN
GREEN
2st suction speed (power)
- led - led
- led - led
- led
ORANGE (amber)ORANGE (amber)
ORANGE (amber)ORANGE (amber)
ORANGE (amber)
3st suction speed (power)
- led RED - led RED
- led RED - led RED
- led RED
4st suction speed (power)
- led RED - led RED
- led RED - led RED
- led RED
(FLASHING)(FLASHING)
(FLASHING)(FLASHING)
(FLASHING)
Note:Note:
Note:Note:
Note: the 4th suction speed (power)
remains on for 5 minutes, after which
the suction motor switches off
(Stand-by)
Touched once more, the suction motor
switches off (Stand-by).
Control bar visual signal :Control bar visual signal :
Control bar visual signal :Control bar visual signal :
Control bar visual signal :
Need to wash the anti-fat filter:Need to wash the anti-fat filter:
Need to wash the anti-fat filter:Need to wash the anti-fat filter:
Need to wash the anti-fat filter:
GREEN led FLASHING (read the
instructions relative to “Reset and
configuration of the filters saturation
signal”)
Need to wash or rNeed to wash or r
Need to wash or rNeed to wash or r
Need to wash or r
eplace the carboneplace the carbon
eplace the carboneplace the carbon
eplace the carbon
filters: filters:
filters: filters:
filters: ORANGE (amber) led
FLASHING (read the instructions
relative to “Reset and configuration of
the filters saturation signal”)
Note:Note:
Note:Note:
Note: reset can be carried out with
the control lever.
Control of the central and sideControl of the central and side
Control of the central and sideControl of the central and side
Control of the central and side
lightslights
lightslights
lights
The central light can be accessed and
switched off by touching THE LOWER
PART of the control bar BRIEFLY.
Control of the Neon lightControl of the Neon light
Control of the Neon lightControl of the Neon light
Control of the Neon light
The neon light can be accessed and
switched off by touching THE LOWER
PART of the control bar IN A
PROLONGED MANNER.
UPPER PUPPER P
UPPER PUPPER P
UPPER P
ARAR
ARAR
AR
TT
TT
T
LED
LOWER PLOWER P
LOWER PLOWER P
LOWER P
ARAR
ARAR
AR
TT
TT
T
ContrContr
ContrContr
Contr
ol barol bar
ol barol bar
ol bar
electrolux electrolux
electrolux electrolux
electrolux control panel
1111
1111
11
GB
Reset and configuration of theReset and configuration of the
Reset and configuration of theReset and configuration of the
Reset and configuration of the
filters saturation signalfilters saturation signal
filters saturation signalfilters saturation signal
filters saturation signal
Switch the hood on at any speed (see
paragraph above “Selection of the
suction speed (power)”
Reset anti-fat filter saturationReset anti-fat filter saturation
Reset anti-fat filter saturationReset anti-fat filter saturation
Reset anti-fat filter saturation
signalsignal
signalsignal
signal
(GREEN LED FLASHING on the(GREEN LED FLASHING on the
(GREEN LED FLASHING on the(GREEN LED FLASHING on the
(GREEN LED FLASHING on the
contrcontr
contrcontr
contr
ol level)ol level)
ol level)ol level)
ol level)
First prFirst pr
First prFirst pr
First pr
oceed with the maintenance ofoceed with the maintenance of
oceed with the maintenance ofoceed with the maintenance of
oceed with the maintenance of
the filter as described in thethe filter as described in the
the filter as described in thethe filter as described in the
the filter as described in the
corrcorr
corrcorr
corr
esponding paragraph.esponding paragraph.
esponding paragraph.esponding paragraph.
esponding paragraph.
Touch in a prolonged manner (more
than 3 seconds) the UPPER PART of
the control lever, the LED stops flashing
to indicate that the reset of the signal
has been carried out and the hood
switches off.
Reset anti-fat filter saturationReset anti-fat filter saturation
Reset anti-fat filter saturationReset anti-fat filter saturation
Reset anti-fat filter saturation
signal ORANGE (amber) LEDsignal ORANGE (amber) LED
signal ORANGE (amber) LEDsignal ORANGE (amber) LED
signal ORANGE (amber) LED
FLASHINGFLASHING
FLASHINGFLASHING
FLASHING
First prFirst pr
First prFirst pr
First pr
oceed with the maintenance ofoceed with the maintenance of
oceed with the maintenance ofoceed with the maintenance of
oceed with the maintenance of
the filter as described in thethe filter as described in the
the filter as described in thethe filter as described in the
the filter as described in the
corrcorr
corrcorr
corr
esponding paragraph.esponding paragraph.
esponding paragraph.esponding paragraph.
esponding paragraph.
Touch in a prolonged manner (more
than 3 seconds) the UPPER PART of
the control lever, the LED stops flashing
to indicate that the reset of the signal
has been carried out and the hood
switches off.
Deactivating the carbon filterDeactivating the carbon filter
Deactivating the carbon filterDeactivating the carbon filter
Deactivating the carbon filter
saturation signal (for specialsaturation signal (for special
saturation signal (for specialsaturation signal (for special
saturation signal (for special
applications)applications)
applications)applications)
applications)
Switch the hood off (see paragraph
above “Select the suction speed
power”)
Touch in a prolonged manner (more
than 5 seconds) the UPPER PART of
the control lever, the LED flashes in
GREEN (amber) to indicate that the
carbon filter saturation signal has been
deactivated.
To reactivate the carbon filter saturation
signal, repeat the operation. The LED
flashes in ORANGE.
Should the hood or the controls fail to
operate: disconnect the power
supply for at least 5 seconds. After
reconnecting the power supply wait
15 seconds and then check that the
cooker hood is now operating
correctly.
1212
1212
12
electr electr
electr electr
electr
oluxolux
oluxolux
olux maintenance and care
GB
Maintenance and Care
Before performing any maintenance operation, isolate the hood fromBefore performing any maintenance operation, isolate the hood from
Before performing any maintenance operation, isolate the hood fromBefore performing any maintenance operation, isolate the hood from
Before performing any maintenance operation, isolate the hood from
the electrical supply by switching off at the connector and removing thethe electrical supply by switching off at the connector and removing the
the electrical supply by switching off at the connector and removing thethe electrical supply by switching off at the connector and removing the
the electrical supply by switching off at the connector and removing the
connector fuse.connector fuse.
connector fuse.connector fuse.
connector fuse.
Or if the appliance has been connected thrOr if the appliance has been connected thr
Or if the appliance has been connected thrOr if the appliance has been connected thr
Or if the appliance has been connected thr
ough a plug and socket, then theough a plug and socket, then the
ough a plug and socket, then theough a plug and socket, then the
ough a plug and socket, then the
plug must be rplug must be r
plug must be rplug must be r
plug must be r
emoved fremoved fr
emoved fremoved fr
emoved fr
om the socket.om the socket.
om the socket.om the socket.
om the socket.
Metal grMetal gr
Metal grMetal gr
Metal gr
ease filterease filter
ease filterease filter
ease filter
The purpose of the grease filters is to
absorb grease particles which form
during cooking and it
mustmust
mustmust
must always be
used, either in the external extraction
or internal re-circulation function.
Attention: Attention:
Attention: Attention:
Attention: the metal grease filters
must be removed and washed, either
by hand or in the dishwasher, every 4
weeks.
Hand washingHand washing
Hand washingHand washing
Hand washing
Soak grease filters for about one hour
in hot water with a grease-loosening
cleaner, then rinse off thoroughly with
hot water. Repeat the process if
necessary. Refit the grease filters
when they are dry.
DishwasherDishwasher
DishwasherDishwasher
Dishwasher
Place grease filters in the dishwasher.
Select most powerful washing
programme and highest temperature,
at least 65°C. Repeat the process.
Refit the grease filters when they are
dry.
When washing the metal grease filter
in the dishwasher a slight
discolouration of the filter can occur,
this does not have any impact on its
performance.
Clean the inner housing using a hand
hot solution only(never use caustic
detergents, abrasive powders or
brushes).
CharChar
CharChar
Char
coal filtercoal filter
coal filtercoal filter
coal filter
The charcoal filter should only be
used if you want to use the hood in
recirculation mode.
To do this you will need an original
charcoal filter (available from your
local Service Force Centre).
Cleaning/rCleaning/r
Cleaning/rCleaning/r
Cleaning/r
eplacing the chareplacing the char
eplacing the chareplacing the char
eplacing the char
coal filtercoal filter
coal filtercoal filter
coal filter
Unlike other charcoal filters, the
LONGLIFE charcoal filter can be
cleaned and reactivated.
With normal use the filter should be
cleaned every second month (when
using the hood 2 and a half hours per
day,on avarage). The best way to clean
the filter is in the dishwasher. Use
normal detergent and choose the
highest temperature (65º C). Wash the
filter separately so that no food parts
gets stuck on the filter and later causes
bad odours.
electrolux electrolux
electrolux electrolux
electrolux maintenance and care
1313
1313
13
GB
To reactivate the charcoal, the filter
should be dried in an oven for 10
minutes with a maximum temperature
of 100º C.
After approximately three years of use,
the charcoal filter should be replaced
with a new one, as the odour reduction
capacity will be reduced.
Always specify the hood model code
number and serial number when
ordering replacement filters. This
information is shown on the rating
plate located on the inside of the unit.
The charcoal filter can be ordered
from your local Service Force Centre.
Dismantling and mounting the filterDismantling and mounting the filter
Dismantling and mounting the filterDismantling and mounting the filter
Dismantling and mounting the filter
in the lower part of the hoodin the lower part of the hood
in the lower part of the hoodin the lower part of the hood
in the lower part of the hood
Turn the bolts a ¼ turn to access
the lower filters.
Turn the internal bolts a ¼ turn to
access the side filters.
Carry out the montage followingCarry out the montage following
Carry out the montage followingCarry out the montage following
Carry out the montage following
the procedure described abovethe procedure described above
the procedure described abovethe procedure described above
the procedure described above
in the reverse sequence.in the reverse sequence.
in the reverse sequence.in the reverse sequence.
in the reverse sequence.
90°
Active charcoal filter
Metal grease filter
Metal grease filter
Active charcoal
filter
1414
1414
14
electr electr
electr electr
electr
oluxolux
oluxolux
olux maintenance and care
GB
Metal grease filter
Dismantling and mounting theDismantling and mounting the
Dismantling and mounting theDismantling and mounting the
Dismantling and mounting the
filter in the upper part of the hoodfilter in the upper part of the hood
filter in the upper part of the hoodfilter in the upper part of the hood
filter in the upper part of the hood
With a small screwdriver lift the 3
tongues that block the filters and
remove the filters.
Remove the frame that blocks the
active carbon filter.
Carry out the montage followingCarry out the montage following
Carry out the montage followingCarry out the montage following
Carry out the montage following
the procedure described abovethe procedure described above
the procedure described abovethe procedure described above
the procedure described above
in the reverse sequencein the reverse sequence
in the reverse sequencein the reverse sequence
in the reverse sequence
..
..
.
WW
WW
W
arar
arar
ar
ningning
ningning
ning
Failure to observe the instructions on
cleaning the unit and changing the
filters will cause a fire hazard. You are
therefore strongly recommended to
follow these instructions.
The manufacturer declines all
responsibility for any damage to the
motor or any fire damage linked to
inappropriate maintenance or failure
to observe the above safety
recommendations.
Active charcoal
filter
electrolux electrolux
electrolux electrolux
electrolux maintenance and care
1515
1515
15
GB
Changing the light bulb(s)Changing the light bulb(s)
Changing the light bulb(s)Changing the light bulb(s)
Changing the light bulb(s)
Disconnect the cooker hood fromDisconnect the cooker hood from
Disconnect the cooker hood fromDisconnect the cooker hood from
Disconnect the cooker hood from
the mains supplythe mains supply
the mains supplythe mains supply
the mains supply
..
..
.
Prior to touching the light bulbsPrior to touching the light bulbs
Prior to touching the light bulbsPrior to touching the light bulbs
Prior to touching the light bulbs
ensure they are cooled down.ensure they are cooled down.
ensure they are cooled down.ensure they are cooled down.
ensure they are cooled down.
Side lights:Side lights:
Side lights:Side lights:
Side lights:
- Remove the protection glass with a
screwdriver.
- Replace the bulb with a new one
with the same characteristics.
- Put the protection glass back.
Central lights:Central lights:
Central lights:Central lights:
Central lights:
- Unscrew the bulb turning it
anticlockwise.
- Replace it with a new one with the
same characteristics.
• Neon lamp:• Neon lamp:
• Neon lamp:• Neon lamp:
• Neon lamp:
- Take the overhead light away,
removing the clips that fix it to the
hood.
- Unhook the lamp from the support
rings.
- Replace it with a new one with the
same characteristics.
- Put the overhead light back.
If the light does not come on, make
sure the bulb has been inserted in
correctly before contacting your local
Service Force Centre.
÷ 45°
÷ 45°
max 40W 40° D25 GU10
12V -20W max - G4
40V - 40W max - 2GX13
1616
1616
16
electr electr
electr electr
electr
oluxolux
oluxolux
olux maintenance and care
GB
Cleaning the hoodCleaning the hood
Cleaning the hoodCleaning the hood
Cleaning the hood
Clean the outside of the hood using a
damp cloth and a solution of water
and mild washing up liquid.
Never use corrosive, abrasive or
flammable cleaning products or
products containing bleach.
Never insert pointed objects in the
motor’s protective grid.
Only ever clean the switch panel and
filter grill using a damp cloth and mild
washing up liquid.
Clean all the plastic parts with a soft
cloth soaked in warm water and
neutral soap.
• It is extremely important to clean the
unit and change the filters at the
recommended intervals. Failure to do
so will cause grease deposits to build
up that could constitute a fire hazard.
electrolux electrolux
electrolux electrolux
electrolux special accessories
1717
1717
17
GB
Special accessoriesSpecial accessories
Special accessoriesSpecial accessories
Special accessories
CharChar
CharChar
Char
coal filtercoal filter
coal filtercoal filter
coal filter Type Evolution
TT
TT
T
elescopic flue elescopic flue
elescopic flue elescopic flue
elescopic flue (only for aspiration version) K690X E-Nr. 942 122 143
Something Not Working
If your appliance fails to work properly please carry out the following checks.
SymptomSymptom
SymptomSymptom
Symptom
The cooker hood will not start...
The cooker hood is not working
The cooker hood has switched off
during operation...
SolutionSolution
SolutionSolution
Solution
Check that: Check that:
Check that: Check that:
Check that: The hood is connected
to the electricity supply.
Check that a fan speed has been
selected.
Check that: Check that:
Check that: Check that:
Check that: The fan speed is set high
enough for the task.
The grease filters are clean.
The kitchen is adequately vented to
allow the entry of fresh air.
If set up for recirculation, check that
the charcoal filter is still effective.
If set up for extraction, check that the
ducting and outlets are not blocked.
The safety cut-out device has been
tripped. Turn off the hob and then wait
for the device to reset. If the hood has
been installed below the heights
indicated in the installation instructions
the motor will cut-out frequently which
will damage the hood.
If after all these checks, the problem persists, contact your local Service Centre,
quoting the model and serial number.
Please note that it will be necessary to provide proof of purchase for any in-
guarantee service calls.
In-guarantee customers should ensure that the above checks have been made as
the engineer will make a charge if the fault is not a mechanical or electrical
breakdown.
1818
1818
18
electr electr
electr electr
electr
oluxolux
oluxolux
olux installation
GB
Installation
TT
TT
T
echnical Detailsechnical Details
echnical Detailsechnical Details
echnical Details
EFC 6690EFC 6690
EFC 6690EFC 6690
EFC 6690
EFC 9690EFC 9690
EFC 9690EFC 9690
EFC 9690
Dimensions (in cm):Dimensions (in cm):
Dimensions (in cm):Dimensions (in cm):
Dimensions (in cm):
Height: 31,1 (39) 31,1 (39)
Width: 59,9 89,9
Depth: 45 45
MaximumMaximum
MaximumMaximum
Maximum
absorbedabsorbed
absorbedabsorbed
absorbed
power:power:
power:power:
power:
230 W230 W
230 W230 W
230 W
230 W230 W
230 W230 W
230 W
Motor: 130 W 130 W
Lighting: 100 W 100 W
Length of the cable:Length of the cable:
Length of the cable:Length of the cable:
Length of the cable:
150 cm150 cm
150 cm150 cm
150 cm
150 cm150 cm
150 cm150 cm
150 cm
Electrical connection:Electrical connection:
Electrical connection:Electrical connection:
Electrical connection:
220-240 V220-240 V
220-240 V220-240 V
220-240 V
220-240 V220-240 V
220-240 V220-240 V
220-240 V
Fuse rating:Fuse rating:
Fuse rating:Fuse rating:
Fuse rating:
5A5A
5A5A
5A
TT
TT
T
5A5A
5A5A
5A
TT
TT
T
Mounting accessories includedMounting accessories included
Mounting accessories includedMounting accessories included
Mounting accessories included
2 Wall hooks with dowels and screws
4 Screws 5 x 45 mm
4 Dowels Ø 8 mm
4 Washers
1 Spanner (for fixingTORX type screws)
1 control bar
electrolux electrolux
electrolux electrolux
electrolux installation
1919
1919
19
GB
Electrical connection
(not for UK)
Safety warSafety war
Safety warSafety war
Safety war
nings for the electriciannings for the electrician
nings for the electriciannings for the electrician
nings for the electrician
Before connecting the appliance to the
power supply, check that the voltage
indicated on the rating plate
corresponds to the mains power supply
available. Appliances fitted with a plug
can be connected to any standard
power socket within easy access.
Should it be necessary to provide a
fixed connection, the hood must only
be installed by an electrician authorised
by the local electricity board. When
installing, an omnipolar disconnector
with a distance of at least 3 mm
between contacts must be provided.
Fixed connection of the appliance must
only be carried out by an authorised
electrician.
Electrical connection for
UK only
Safety warSafety war
Safety warSafety war
Safety war
nings for the electriciannings for the electrician
nings for the electriciannings for the electrician
nings for the electrician
Connect the hood to the mains supply
via a double pole switch which has 3
mm minimum separation between the
contacts.
The switch must be accessible at all
times.
The following is valid in the United
Kingdom only:
- the wire which is coloured green and
yellow must be connected to the
terminal which is marked with the
letter E or by the earth symbol ( ),
or coloured green or green and
yellow;
- the wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black, -
- the wire which is coloured brown
must be connected to the terminal
which is marked with the letter L or
coloured red.
BROWN
CORD CLAMP
BLUE
GREEN & YELLOW
5AT
IMPORIMPOR
IMPORIMPOR
IMPOR
TT
TT
T
ANT!ANT!
ANT!ANT!
ANT! Power cable repalcement must be undertaken by the authorized
service assistance centre in order to prevent any risks.
2020
2020
20
electr electr
electr electr
electr
oluxolux
oluxolux
olux installation
GB
InstallationInstallation
InstallationInstallation
Installation
Make sure that the cooker hood is disconnected from the powerMake sure that the cooker hood is disconnected from the power
Make sure that the cooker hood is disconnected from the powerMake sure that the cooker hood is disconnected from the power
Make sure that the cooker hood is disconnected from the power
supply before carrying out the installation.supply before carrying out the installation.
supply before carrying out the installation.supply before carrying out the installation.
supply before carrying out the installation.
Before installing the hood, remove the
metal bracket and the wooden plank
fixed to the upper part that are part of
the packing.
Dispose of the packing in accordance
with the regulations in force.
If you want to install a telescopic flue
kit (optionally purchased as a special
accessory, see “special accessories”
chapter), read the instructions sent
with the kit carefully.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

Electrolux EFC9690X User manual

Category
Cooker hoods
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI