Harbor Freight Tools 90975 User manual

Type
User manual

This manual is also suitable for

3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright
©
2004 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be
reproduced in any shape or form without the express written consent
of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
®
COTTON HAMMOCK
WITH FRAME
ASSEMBLY INSTRUCTIONS
90975
SKU 90975 Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and
precautions, assembly instructions, operating and maintenance
procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover.
Keep the manual and invoice in a safe and dry place for future
reference.
Safety Warnings and Precautions
WARNING: When using this product, basic safety precautions should always
be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep children away. Children must never be allowed to climb into this product
without adult assistance . Flipping over can occur and can result in injury.
2. Position this product on a flat grassy area.
3. Stay alert. Watch what you are doing. Use common sense. Do not try to exit
this product without assistance when you are tired or you could lose your balance.
4. Check for damaged parts. Before using this product, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for cracked or rusted rings, torn or
worn canvas, loose bolts, worn ropes, or any other condition that shows wear
and tear of this product. Replace or repair any broken or worn parts before use.
If any part of the Hammock (9) is worn we suggest you replace the entire
Hammock (9).
5. Do not leave out in harsh weather conditions. Sunlight or rain can rot rope
and canvas. Always check the condition of this product before sitting or lying
upon this product.
DESCRIPTION
Powder Coated Steel
133”L x 48-1/2” W x 56-1/4” H
100% Cotton -74” L x 46-1/2” W
Wooden Brace with Steel Rings and Woven Rope
350 Lbs.
46 Lbs.
ITEM
Frame
Overall Dimension
Hammock
End Supports
Weight Capacity
Net Weight
SKU 90975 Page 3
Unpacking
When unpacking, check to make sure the following parts (shown on page 5)
are included. If any parts are missing or broken, please call Harbor Freight Tools at
the number on the cover of this manual.
Assembly
1. Locate both Bases (2). Place each Elbow (3) over each Base (2), line up the
bolt holes, and fix in place using the 4 sets of Elbow Nuts and Bolts (5).
See Figure A.
Figure A
2. Select a surface that will not scratch the finish of the frame. Place both Elbows
(3) on each side of the Center Joining Tube (4) so that the horizontal ends are
on the inside. See
Figure A.
3. Insert the Center Joining Tube (4) over the lower part of one Elbow (3) as far as
it will go. Line up the Center Joining Tube Bolt (6) with the notch on the Elbow
and tighten partially. Repeat on the other side. Tighten both Center Joining
Tube Bolts securely. (Check for tightness periodically).
See Figure A.
4. Attach Square End Caps (7) onto both ends of each Base (2).
See Figure D.
5. Insert the Risers (1) over the upper part of the Elbows. Be sure the notches for
hanging the Hammock (9) are facing inwards.
See Figure B.
The Risers (1)
should rest on the Ring Stopper on the Elbow ( 3).
See Figure C.
Center Joining
Tube (4)
Riser (1)
Center Joining
Tube Bolt (6)
Base (2)
Elbow (3)
Elbow Nut
and Bolt (5)
6. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are available
from Harbor Freight Tools.
7. Do not use or assemble under the influence of alcohol or drugs.
SKU 90975 Page 4
Maintenance
1. When cleaning, wipe Cotton Hammock with a soft damp cloth. Dry thoroughly.
2. Dismantling and storing during harsh weather will prolong the life of the
Hammock.
6. Hook the Metal Rings on the Cotton Hammock (9) (left and right) over the
Notches. Test to see that Hammock is securely attached before getting into
the Hammock. See
Figure D.
7. Attach Round End Caps (8) onto the ends of the Risers (1). See
Figure B.
Metal Rings Metal Rings
Cotton Hammock (9)
Figure D
Square End Caps (7)
Round End Cap (8)
Ring Stopper
on Elbow (3)
Riser (1)
Elbow (3)
Riser (1)
Notches
Facing
Inside
Figure B
Figure C
Metal Rings
SKU 90975 Page 5
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES That ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only
and are not available individually as replacement parts.
PARTS LIST
1
2
3
4
5
6
7
8
9
8
2
4637
2
2
2
1
4 sets
2
4
2
1
Riser
Base
Elbow
Center Joining Tube
Elbow Nut and Bolt
Center Joining Tube Bolt
Square End Caps
Round End Caps
Cotton Hammock with Wooden Spreaders
PART DESCRIPTION QTY.
6
1
5
9
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Harbor Freight Tools 90975 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI