Cisco Systems MX300 User manual

Brand: Cisco Systems

Model: MX300

Type: User manual

This manual is also suitable for

Installing Cisco TelePresence MX300 - Floor Stand

2

Unpacking the MX300 box with the LCD video unit, Touch controller and accessories

i Cut the straps and lift off

the outer covering.

ii Remove the upper foam

protection.

Note: Leave the LCD

video unit in the bottom

tray for now.

iii Lift out the rectangular

box behind the LCD video

unit.

This box contains two

smaller boxes: One with

the Touch controller, and

one accessories box with

the microphones, cables,

screws and screwdriver.

Bottom tray

LCD video

unit

Touch controller

with cable

Accessories box:

• Two microphones

• Power cable

• Presentation cable

(VGA to DVI-I; stereo audio)

• Ethernet cable

• Four screws for fastening

the LCD video unit to the

floor stand

• Hexagonal screwdriver

• Two pairs of gloves

1

Unpacking the floor stand box and mounting the floor stand

i Unpack the floor stand box with the floor stand

base, floor stand column and floor stand covers,

screws and Allen key.

ii Place the floor stand base on the floor with the

cable channel facing upward and backward.

iii Raise the floor stand column with the cable

channel facing backward. Place the column

on the base and make sure the holes for the

screws are aligned.

iv Fasten the column to the base using the four

screws (tool: Allen key).

The two floor stand covers

will be mounted in step 6.

Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)

Floor stand

base

Floor stand

column

3

Mounting the LCD video unit to the floor stand

Cable channel lid

(for strain relief)

Floor stand

LCD video

unit

Note: Always use the provided gloves when handling

the LCD video unit to avoid stains on the unit’s surface.

i Lift the LCD video unit from the

bottom tray and slide it onto the

top of the floor stand column.

Two people working together are

required for this operation.

ii Remove the cable channel lid (see illustration) to

get access to the holes for the screws.

iii Fasten the LCD video unit to the column using the

four screws (tool: hexagonal screwdriver).

The MX300 delivery

The MX300 with a floor stand is delivered in three boxes

with the following parts:

• Floor stand column, floor stand base and floor stand

covers. Screws and Allen key

• LCD video unit, touch controller, microphones and

cables. Screws, screwdriver and gloves

• Back cover

Manpower

Two people working together are required to mount the

LCD video unit to the floor stand column.

Dimensions

Height (without camera): 1420 mm / 56 in.

Width: 1290 mm / 51 in.

Depth: 730 mm / 29 in.

Weight: 42 kg / 93 lb

Documentation

The user documentation for this product, including

compliance and safety information, is available on the Cisco

web site, http://www.cisco.com/go/telepresence/docs.

Outer

covering

31 kg / 68 lb

Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)

Floor Stand Base Screw (M6 x 16 Black)

Main Unit Screw (M6 x 20 Black)

Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)

Front

Installing Cisco TelePresence MX300 - Floor Stand

4

Connecting the cables

EMC A-Class declaration

WARNING: This is a class A product. In a domestic environment this

product may cause radio interference in which case the user may be

required to take adequate measures.

声明

此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种

情况下，可能需要用户对其干扰采取切实可行的措施。

WARNING: This is a class A product. In a domestic environment

this product may cause radio interference in which case the user

may be required to take adequate measures.

i Connect the cables. The connectors are placed at the rear

side of the LCD video unit. See illustration for details.

ii Lead the cables down the cable channel.

iv Lead the cables in the cable slots in the floor stand. Be

careful to put the cables below the hooks.

You can lead the cables out at the front or back of the system

as appropriate.

Note: If cables are longer than you need, you can lead them

around the cable slot several times. If more convenient, do

this before connecting the cables to the unit.

iii Snap on the cable channel

lid for strain relief.

Note: When you position

the cables side by side it

is easier to snap on the lid.

LCD video unit connectors

Power

supply

45,7

79,4

AC Input

Power

switch

For maintenance only

226,8

46,1

Touch controller

Local area

network (LAN)

PC audio input

PC video input

Audio line output

(cable not included)

Microphones

Reset factory settings

6

Snapping on the floor stand covers and back cover

5

Switching on the system

i Ensure that the cables are placed

under the hooks in the cable slots.

Then snap on the two floor stand

covers, one at a time. The covers are

fastened with magnets when they are

lowered toward the base.

ii Snap on the back cover to

hide the connectors and

cables.

The back cover is delivered

in a separate box.

i Plug in the cables from the LCD video unit as appropriate, and

make sure the Touch controller is connected.

SAFETY REQUIREMENT: The equipment shall be installed close to

the socket outlet. The socket outlet shall be easily accessible after

installation.

ii Switch on the system.

The power switch is located above the power connector on the

rear side of the LCD video unit.

iii Wait while the MX300 starts up. Normally this takes just a few

minutes. If an automatic software upgrade occurs the start-up

process may take up to 15minutes.

When the home menu and contact list appear on the Touch

controller the system is ready to use.

CAUTION: To alter the camera position always use the Camera

Control panel on the Touch controller; never move the camera

manually when the power is switched on.

You can lock/unlock the back

cover by lifting this handle.

Use both hands if required.

7

Finishing up

i Remove the protective foil from the LCD video unit.

ii If required, clean the Touch display (not the LCD video

display) using the dry cleaning cloth provided.

iii Unfold the rear-mounted foot on the Touch controller to

increase its tilt.

On our web site you will find an overview of the

worldwide Cisco contacts.

Go to: http://www.cisco.com/web/siteassets/contacts.

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Dr.

San Jose, CA 95134 USA



LCD video unit placement

The placement of the video system in a room will influence the

overall conferencing experience both at the local and remote

sites.

You should aim for:

• Good illumination of a person’s face to avoid annoying

shadows.

• No direct light on the LCD video display to avoid reflections.

The illustrations to the right show in general where to place your

MX300 system depending on the window positions in the room.

For each room layout the MX300 position(s) marked with A are

preferred, then B and finally C. You should avoid any position

not shown in the illustrations.

Microphone placement

Correctly placed microphones are very important to obtain a

good conferencing experience.

We recommend that you place the microphone(s) as close to

all users as possible, and that you avoid putting equipment

with noisy fans, such as computers and projectors, close to a

microphone.

If you are using more than one microphone, place them far

apart to minimize the interference. The required distance

between the microphones depends on the acoustics of your

room; normally 2 m (6.5 ft) will suffice.

The MX300 internal microphone may suffice in a small office

or meeting room when all participants are closer to the display

than 2.5 m (8 ft). Still a correctly placed external microphone

often performs better. The internal microphone is automatically

disabled when connecting an external microphone.

If you want to learn more about optimizing your office

or meeting room for video conferencing, please read

the Video conferencing room primer and Guidelines

for video conferencing room acoustics documents

that are available on the Cisco web site,

http://www.cisco.com/go/telepresence/docs.

Cisco Systems MX300 User manual

Brand: Cisco Systems

Model: MX300

Type: User manual

This manual is also suitable for

Download PDF

report

Cisco Systems MX300 User manual

This manual is also suitable for

Cisco Systems MX300 User manual

Related papers

Other documents