selLEton SL-60KX Installation guide

SL-60KX
Brand
selLEton
Model
SL-60KX
Category
Signal cables
Type
Installation guide

The selLEton SL-60KX is an axle scale specifically designed to weigh heavy vehicles in motion, providing accurate weighing results up to a maximum capacity of 60,000 pounds per axle. With its state-of-the-art technology, this device allows for efficient and precise weighing operations in various industrial and commercial settings.

The selLEton SL-60KX is an axle scale specifically designed to weigh heavy vehicles in motion, providing accurate weighing results up to a maximum capacity of 60,000 pounds per axle. With its state-of-the-art technology, this device allows for efficient and precise weighing operations in various industrial and commercial settings.

Installation Instruction for Axle Scales
SL-310-20K lb
load cell with 1”-14UNF Feet
SL-310-20K lb
load cell with 1”-14UNF Feet
310-
SL-20K lbith 1
load cell w ”-14UNF Feet
Junction Box position
SL-7510-C-12-2PT Indicator
singal cable connect
to indicator
SL-7510-C-12-2PT
Indicator
Operation
Manual
Expansion Bolts
for Ramp
M10x100mm
Installation Plate
Eyebolts
Scale Components
platform (total: 2pcs) ramp A (total: 4pcs)
indicator (total: 1pcs)feet (total: 8pcs) junction box (total: 2pcs)
Singal cable for indicator
(total: 2pcs)
bending plate (total: 2pcs)
load cell (total: 8pcs)
Bolts details
expansion bolt
M16 x 100 mm
(total: 28 pcs)
bolt for bending plate
(total: 16 pcs)
bolt for load cell
M24 x 75 mm (total: 16 pcs)
Limit bolt
M20 x 70 mm
(total: 8 pcs)
M16 eyebolt
(total: 2 pcs)
1
Tools Required for Installation
folklift
wrench
tape churn drill
flat screwdriver hammer
2
(1) Make sure the complete installation is done on a level ground .
(2) Bolt the installation plate to the ramps and place the
ramps 87" apart in parallel with forklift . Installation Plate
forklift
wrench
(4) Place the platform between the two ramps,
making sure all the feet sit inside the rings
on the ramps .
Installation Plate
(3) Bolt the installation plates to the platform and
screw the four threaded level feet into the four
corners of the platform while lifting it with the
forklift .
flat screwdriver
1’’-14UNF Feet
tape
If necessary, adjust the height
with a screwdriver from the top.
3
(5) Pull out the interface cable
Open the cover on the side and you
will find the junction box with a 50ft
long cable nested inside. Run the
cable (with connector) through hole
on the bottom and pull it out from
underneath as long as you need .
Close the cover with the original
screws after this is finished .
Hole for cable though
cable for load cell
cable for load cell
cable for load cell
cable for connect
to indicator
(6) Follow the same steps to install
the other set .
(8) For permanent use, install anchoring
bolts to the ramps .
(7) Plug the connectors on the interface
cables to the 2 ports of the indicator .
churn drill
hammer
expansion bolt
thread x length :
M10x100mm bolts
OP-900B-12-2PT Indicator
singal cable connect to indicator
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

selLEton SL-60KX Installation guide

SL-60KX
Brand
selLEton
Model
SL-60KX
Category
Signal cables
Type
Installation guide

The selLEton SL-60KX is an axle scale specifically designed to weigh heavy vehicles in motion, providing accurate weighing results up to a maximum capacity of 60,000 pounds per axle. With its state-of-the-art technology, this device allows for efficient and precise weighing operations in various industrial and commercial settings.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents