ESAB 170Ti Transtig Welding Inverter User manual

Category
Welding System
Type
User manual
PFC
Art # A-11812
170Ti
Service Manual
Revision: AA Issue Date: February 7, 2013 Manual No.: 0-5278
Operating Features:
TRANSTIG
WELDING INVERTER
WE APPRECIATE YOUR BUSINESS!
Congratulations on your new Cigweld product. We are proud
to have you as our customer and will strive to provide you with
the best service and reliability in the industry. This product
is backed by our extensive warranty and world-wide service
network. To locate your nearest distributor or service provider call
+1300 654 674, or visit us on the web at www.cigweld.com.au
This Service Manual has been designed to instruct you on the correct
use and operation of your CIGWELD product. Your satisfaction with
this product and its safe operation is our ultimate concern. Therefore
please take the time to read the entire manual, especially the Safety
Precautions. They will help you to avoid potential hazards that may
exist when working with this product.
YOU ARE IN GOOD COMPANY!
The Brand of Choice for Contractors and Fabricators Worldwide.
CIGWELD is the Market Leading Brand of Arc Welding Products for
Victor Technologies International. We are a mainline supplier to major
welding industry sectors in the Asia Pacific and emerging global
markets including; Manufacturing, Construction, Mining, Automotive,
Engineering, Rural and DIY.
We distinguish ourselves from our competition through market-
leading, dependable products that have stood the test of time. We
pride ourselves on technical innovation, competitive prices, excellent
delivery, superior customer service and technical support, together
with excellence in sales and marketing expertise.
Above all, we are committed to develop technologically advanced
products to achieve a safer working environment for industry
operators.
!
WARNINGS
Read and understand this entire Manual and your employer’s safety practices before installing,
operating, or servicing the equipment.
While the information contained in this Manual represents the Manufacturer’s best judgement,
the Manufacturer assumes no liability for its use.
Service Manual Number 0-5278 for:
Cigweld Transtig 170Ti Mine Spec Inverter Plant Part Number W1007180
Cigweld Transtig 170Ti Mine Spec Power Source (packed) Part Number W1007179
Published by:
CIGWELD Pty Ltd
71 Gower Street
Preston, Victoria, Australia, 3072
+61 3 9474 7400 +61 3 9474 7391
www.cigweld.com.au
Copyright 2013 by
CIGWELD Pty Ltd.
All rights reserved.
Reproduction of this work, in whole or in part, without written permission of the
publisher is prohibited.
The publisher does not assume and hereby disclaims any liability to any party for any
loss or damage caused by any error or omission in this Manual, whether such error
results from negligence, accident, or any other cause.
Publication Date: February 7, 2013
Record the following information for Warranty purposes:
Where Purchased: ____________________________________
Purchase Date: ____________________________________
Equipment Serial #: ____________________________________
TABLE OF CONTENTS
SECTION 1:
ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS ..................................... 1-1
1.01 Arc Welding Hazards ....................................................................................... 1-1
1.02 Principal Safety Standards .............................................................................. 1-5
1.03 Declaration of Conformity ............................................................................... 1-6
1.04 Servicing Hazards ........................................................................................... 1-7
1.05 EMF Information ............................................................................................. 1-9
SECTION 2:
INTRODUCTION ..................................................................................... 2-1
2.01 How To Use This Manual ................................................................................ 2-1
2.02 Equipment Identification ................................................................................. 2-1
2.03 Receipt Of Equipment ..................................................................................... 2-1
2.04 Symbol Chart .................................................................................................. 2-2
2.05 Description ..................................................................................................... 2-3
2.06 User Responsibility ......................................................................................... 2-3
2.07 Transporting Methods ..................................................................................... 2-3
2.08 Packaged Items .............................................................................................. 2-3
SECTION 3:
INSTALLATION ....................................................................................... 3-1
3.01 Duty Cycle ....................................................................................................... 3-1
3.02 Specifications ................................................................................................. 3-2
3.03 Environment ................................................................................................... 3-3
3.04 Location .......................................................................................................... 3-3
3.05 Ventilation ....................................................................................................... 3-4
3.06 Mains Supply Voltage Requirements .............................................................. 3-4
3.07 Electromagnetic Compatibility ........................................................................ 3-4
SECTION 4:
OPERATION ........................................................................................... 4-1
4.01 Transtig 170Ti Power Source Controls, Indicators and Features ..................... 4-1
4.02 Shielding Gas Regulator Operating Instructions ........................................... 4-11
4.03 Setup for TIG (GTAW) Welding ..................................................................... 4-14
4.04 Foot Control Part No. W4015800 (Optional Accessory) ................................ 4-15
4.05 Setup for Manual Arc (MMAW) Welding ..................................................... 4-17
SECTION 5:
THEORY OF OPERATION ............................................................................ 5-1
5.01 Inverter Design ............................................................................................... 5-1
SECTION 6:
TROUBLESHOOTING ................................................................................ 6-1
6.01 Basic Troubleshooting .................................................................................... 6-1
6.02 Power Source Faults ....................................................................................... 6-3
6.03 Factory Reset ................................................................................................. 6-4
6.04 Advanced Troubleshooting .............................................................................. 6-4
6.05 Test Equipment and Tools for Troubleshooting and Servicing......................... 6-5
6.06 Visually Inspect ............................................................................................... 6-5
TABLE OF CONTENTS
6.07 Preliminary DC Bus Measurement of the Main Inverter PCB .......................... 6-6
6.08 Preliminary Check of the Main Inverter PCB ................................................... 6-7
6.09 Check Main Input Rectifier .............................................................................. 6-8
6.10 DC Bus Voltage Measurement ........................................................................ 6-9
6.11 PCB Connectors ............................................................................................ 6-10
6.12 DIP Switch Settings, Control PCB ................................................................. 6-17
6.13 Calibration .................................................................................................... 6-18
6.14 Main Circuit Description ............................................................................... 6-19
SECTION 7:
DISASSEMBLY PROCEDURE ....................................................................... 7-1
7.01 Safety Precautions for Disassembly ............................................................... 7-1
7.02 Cover Panel Removal ...................................................................................... 7-1
7.03 Front Panel Removal ....................................................................................... 7-2
7.04 Display PCB Removal ..................................................................................... 7-3
7.05 Control PCB Removal ..................................................................................... 7-4
7.06 Rear Panel Removal ........................................................................................ 7-5
7.07 ON/ OFF Switch and Power Cord Removal ...................................................... 7-6
7.08 HF PCB Removal ............................................................................................. 7-7
7.09 Base Panel Removal ....................................................................................... 7-8
SECTION 8:
ASSEMBLY PROCEDURE ............................................................................ 8-1
8.01 Installing Base Panel ....................................................................................... 8-1
8.02 Installing Rear Panel ....................................................................................... 8-2
8.03 Installing Front Panel ...................................................................................... 8-3
8.04 Installing Control PCB ..................................................................................... 8-4
8.05 Installing Cover Panel ..................................................................................... 8-5
SECTION 9:
KEY SPARE PARTS ................................................................................... 9-1
9.01 Power Source ................................................................................................. 9-1
9.02 TIG Torch W4014604 ...................................................................................... 9-3
9.03 Stick Electrode Holder with Trigger Switch 646761(where supplied) .............. 9-4
APPENDIX 1: OPTIONS AND ACCESSORIES ............................................................ A-1
APPENDIX 2: TRANSTIG 170TI CIRCUIT DIAGRAM ................................................... A-2
CIGWELD - LIMITED WARRANTY TERMS ..................................................................1
TERMS OF WARRANTY – JANUARY 2013 .................................................................2
WARRANTY SCHEDULE – JANUARY 2013 ................................................................. 3
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION ................................................ 5
TRANSTIG 170Ti
Manual 0-5278 1-1 GENERAL INFORMATION
1.01 Arc Welding Hazards
WARNING
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause
fatal shocks or severe burns. The electrode
and work circuit is electrically live when-
ever the output is on. The input power cir-
cuit and machine internal circuits are also
live when power is on. In semiautomatic
or automatic wire welding, the wire, wire
reel, drive roll housing, and all metal parts
touching the welding wire are electrically
live. Incorrectly installed or improperly
grounded equipment is a hazard.
1. Do not touch live electrical parts.
2. Wear dry, hole-free insulating gloves and body
protection.
3. Insulate yourself from work and ground using dry
insulating mats or covers.
4. Disconnect input power or stop engine before
installing or servicing this equipment. Lock input
power disconnect switch open, or remove line
fuses so power cannot be turned on accidentally.
5. Properly install and ground this equipment accord-
ing to its Owner’s Manual and national, state, and
local codes.
6. Turn off all equipment when not in use. Disconnect
power to equipment if it will be left unattended or
out of service.
7. Use fully insulated electrode holders. Never dip
holder in water to cool it or lay it down on the
ground or the work surface. Do not touch holders
connected to two welding machines at the same
time or touch other people with the holder or
electrode.
8. Do not use worn, damaged, undersized, or poorly
spliced cables.
9. Do not wrap cables around your body.
10. Ground the workpiece to a good electrical (earth)
ground.
11. Do not touch electrode while in contact with the
work (ground) circuit.
12. Use only well-maintained equipment. Repair or
replace damaged parts at once.
13. In confined spaces or damp locations, do not use
a welder with AC output unless it is equipped with
a voltage reducer. Use equipment with DC output.
14. Wear a safety harness to prevent falling if working
above floor level.
15. Keep all panels and covers securely in place.
SECTION 1:
ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
!
WARNING
PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN
AWAY. PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING YOUR DOCTOR. DO NOT LOSE THESE
INSTRUCTIONS. READ OPERATING/INSTRUCTION MANUAL BEFORE INSTALLING, OPERATING OR
SERVICING THIS EQUIPMENT.
Welding products and welding processes can cause serious injury or death, or damage to other equipment or
property, if the operator does not strictly observe all safety rules and take precautionary actions.
Safe practices have developed from past experience in the use of welding and cutting. These practices must be
learned through study and training before using this equipment. Some of these practices apply to equipment
connected to power lines; other practices apply to engine driven equipment. Anyone not having extensive
training in welding and cutting practices should not attempt to weld.
Safe practices are outlined in the Australian Standard AS1674.2-2007 entitled: Safety in welding and allied
processes Part 2: Electrical. This publication and other guides to what you should learn before operating
this equipment are listed at the end of these safety precautions. HAVE ALL INSTALLATION, OPERATION,
MAINTENANCE, AND REPAIR WORK PERFORMED ONLY BY QUALIFIED PEOPLE.
TRANSTIG 170Ti
GENERAL INFORMATION 1-2 Manual 0-5278
WARNING
ARC RAYS can burn eyes and skin; NOISE
can damage hearing.
Arc rays from the welding process produce
intense heat and strong ultraviolet rays
that can burn eyes and skin. Noise from
some processes can damage hearing.
1. Use a Welding Helmet or Welding Faceshield fitted
with a proper shade of filter (see ANSI Z49.1 and
AS 1674 listed in Safety Standards) to protect your
face and eyes when welding or watching.
2. Wear approved safety glasses. Side shields recom-
mended.
3. Use protective screens or barriers to protect others
from flash and glare; warn others not to watch the
arc.
4. Wear protective clothing made from durable,
flame-resistant material (wool and leather) and
foot protection.
5. Use approved ear plugs or ear muffs if noise level
is high.
6. Never wear contact lenses while welding.
Recommended Protective Filters for Electric Welding
Description of Process
Approximate Range of
Welding Current in Amps
Minimum Shade Number of
Filter(s)
Manual Metal Arc Welding - covered
electrodes (MMAW)
Less than or equal to 100 8
100 to 200 10
200 to 300 11
300 to 400 12
Greater than 400 13
Gas Metal Arc Welding (GWAW)
(MIG) other than Aluminium and
Stainless Steel
Less than or equal to 150 10
150 to 250 11
250 to 300 12
300 to 400 13
Greater than 400 14
Gas Metal Arc Welding (GMAW)
(MIG) Aluminium and Stainless Steel
Less than or equal to 250 12
250 to 350 13
Gas Tungsten Arc Welding (GTAW)
(TIG)
Less than or equal to 100 10
100 to 200 11
200 to 250 12
250 to 350 13
Greater than 350 14
Flux-cored Arc Welding (FCAW) -with
or without shielding gas.
Less than or equal to 300 11
300 to 400 12
400 to 500 13
Greater than 500 14
Air - Arc Gouging Less than or equal to 400 12
Plasma - Arc Cutting
50 to 100 10
100 to 400 12
400 to 800 14
Plasma - Arc Spraying
15
Plasma - Arc Welding
Less than or equal to 20 8
20 to 100 10
100 to 400 12
400 to 800 14
Submerged - Arc Welding
2(5)
Resistance Welding
Safety Spectacles or eye
shield
Refer to standard AS/NZS 1338.1:1992 for comprehensive information regarding the above table.
TRANSTIG 170Ti
Manual 0-5278 1-3 GENERAL INFORMATION
WARNING
FUMES AND GASES can be hazardous to
your health.
Welding produces fumes and gases.
Breathing these fumes and gases can be
hazardous to your health.
1. Keep your head out of the fumes. Do not breathe
the fumes.
2. If inside, ventilate the area and/or use exhaust at
the arc to remove welding fumes and gases.
3. If ventilation is poor, use an approved air-supplied
respirator.
4. Read the Material Safety Data Sheets (MSDSs)
and the manufacturer’s instruction for metals,
consumables, coatings, and cleaners.
5. Work in a confined space only if it is well venti-
lated, or while wearing an air-supplied respirator.
Shielding gases used for welding can displace air
causing injury or death. Be sure the breathing air
is safe.
6. Do not weld in locations near degreasing, cleaning,
or spraying operations. The heat and rays of the
arc can react with vapours to form highly toxic
and irritating gases.
7. Do not weld on coated metals, such as galvanized,
lead, or cadmium plated steel, unless the coating
is removed from the weld area, the area is well
ventilated, and if necessary, while wearing an air-
supplied respirator. The coatings and any metals
containing these elements can give off toxic fumes
if welded.
WARNING
WELDING can cause fire or explosion.
Sparks and spatter fly off from the welding
arc. The flying sparks and hot metal, weld
spatter, hot workpiece, and hot equipment
can cause fires and burns. Accidental con
-
tact of electrode or welding wire to metal
objects can cause sparks, overheating,
or fire.
1. Protect yourself and others from flying sparks and
hot metal.
2. Do not weld where flying sparks can strike flam-
mable material.
3. Remove all flammables within 10M of the welding
arc. If this is not possible, tightly cover them with
approved covers.
4. Be alert that welding sparks and hot materials from
welding can easily go through small cracks and
openings to adjacent areas.
5. Watch for fire, and keep a fire extinguisher nearby.
6. Be aware that welding on a ceiling, floor, bulkhead,
or partition can cause fire on the hidden side.
7. Do not weld on closed containers such as tanks
or drums.
8. Connect work cable to the work as close to the
welding area as practical to prevent welding cur-
rent from travelling long, possibly unknown paths
and causing electric shock and fire hazards.
9. Do not use welder to thaw frozen pipes.
10. Remove stick electrode from holder or cut off
welding wire at contact tip when not in use.
WARNING
FLYING SPARKS AND HOT METAL can
cause injury.
Chipping and grinding cause flying metal.
As welds cool, they can throw off slag.
1. Wear approved face shield or safety goggles. Side
shields recommended.
2. Wear proper body protection to protect skin.
WARNING
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under
high pressure. If damaged, a cylinder can
explode. Since gas cylinders are normally
part of the welding process, be sure to
treat them carefully.
1. Protect compressed gas cylinders from excessive
heat, mechanical shocks, and arcs.
2. Install and secure cylinders in an upright position
by chaining them to a stationary support or equip-
ment cylinder rack to prevent falling or tipping.
3. Keep cylinders away from any welding or other
electrical circuits.
4. Never allow a welding electrode to touch any
cylinder.
TRANSTIG 170Ti
GENERAL INFORMATION 1-4 Manual 0-5278
5. Use only correct shielding gas cylinders,
regulators, hoses, and fittings designed for the
specific application; maintain them and associated
parts in good condition.
6. Turn face away from valve outlet when opening
cylinder valve.
7. Keep protective cap in place over valve except
when cylinder is in use or connected for use.
8. Read and follow instructions on compressed
gas cylinders, associated equipment, and CGA
publication P-1 listed in Safety Standards.
WARNING
MOVING PARTS can cause injury.
Moving parts, such as fans, rotors, and belts can cut
fingers and hands and catch loose clothing.
1. Keep all doors, panels, covers, and guards closed
and securely in place.
2. Stop engine before installing or connecting unit.
3. Have only qualified people remove guards or
covers for maintenance and troubleshooting as
necessary.
4. To prevent accidental starting during servicing,
disconnect negative (-) battery cable from battery.
5. Keep hands, hair, loose clothing, and tools away
from moving parts.
6. Reinstall panels or guards and close doors when
servicing is finished and before starting engine.
!
WARNING
This product, when used for welding or
cutting, produces fumes or gases which
contain chemicals know to the State of
California to cause birth defects and, in
some cases, cancer. (California Health &
Safety code Sec. 25249.5 et seq.)
NOTE
Considerations About Welding And The
Effects of Low Frequency Electric and
Magnetic Fields
The following is a quotation from the General Con-
clusions Section of the U.S. Congress, Office of
Technology Assessment, Biological Effects of Power
Frequency Electric & Magnetic Fields - Background
Paper, OTA-BP-E-63 (Washington, DC: U.S. Govern-
ment Printing Office, May 1989): “...there is now
a very large volume of scientific findings based on
experiments at the cellular level and from studies
with animals and people which clearly establish that
low frequency magnetic fields and interact with, and
produce changes in, biological systems. While most
of this work is of very high quality, the results are
complex. Current scientific understanding does not
yet allow us to interpret the evidence in a single coher-
ent framework. Even more frustrating, it does not yet
allow us to draw definite conclusions about questions
of possible risk or to offer clear science-based advice
on strategies to minimize or avoid potential risks.”
To reduce magnetic fields in the workplace, use the
following procedures.
1. Keep cables close together by twisting or taping
them.
2. Arrange cables to one side and away from the
operator.
3. Do not coil or drape cable around the body.
4. Keep welding power source and cables as far away
from body as practical.
ABOUT PACEMAKERS:
The above procedures are among those
also normally recommended for pace-
maker wearers. Consult your doctor for
complete information.
TRANSTIG 170Ti
Manual 0-5278 1-5 GENERAL INFORMATION
1.02 Principal Safety Standards
Safety in Welding and Cutting, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd.,
Miami, FL 33126.
Safety and Health Standards, OSHA 29 CFR 1910, from Superintendent of Documents, U.S. Government
Printing Office, Washington, D.C. 20402.
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers That Have Held
Hazardous Substances, American Welding Society Standard AWS F4.1, from American Welding Society, 550
N.W. LeJeune Rd., Miami, FL 33126.
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Batterymarch Park,
Quincy, MA 02269.
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association,
1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202.
Code for Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Stan-
dards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3.
Safe Practices for Occupation and Educational Eye and Face Protection, ANSI Standard Z87.1, from American
National Standards Institute, 1430 Broadway, New York, NY 10018.
Cutting and Welding Processes, NFPA Standard 51B, from National Fire Protection Association, Batterymarch
Park, Quincy, MA 02269.
Safety in welding and allied processes Part 1: Fire Precautions, AS 1674.1-1997 from SAI Global Limited,
www.saiglobal.com.
Safety in welding and allied processes Part 2: Electrical, AS 1674.2-2007 from SAI Global Limited, www.
saiglobal.com.
Filters for eye protectors - Filters for protection against radiation generated in welding and allied operations
AS/NZS 1338.1:1992 from SAI Global Limited, www.saiglobal.com.
TRANSTIG 170Ti
GENERAL INFORMATION 1-6 Manual 0-5278
1.03 Declaration of Conformity
Manufacturer: CIGWELD
Address: 71 Gower St, Preston
Victoria 3072
Australia
Description of equipment: Welding Equipment (GTAW, MMAW) including, but not limited to CIGWELD Transtig
170Ti Welding Inverter and associated accessories.
Serial numbers are unique with each individual piece of equipment and details description, parts used to
manufacture a unit and date of manufacture.
The equipment conforms to all applicable aspects and regulations of the ‘Low Voltage Directive’ (2006/95 EC)
and to the National legislation for the enforcement of the Directive.
National Standard and Technical Specifications
The product is designed and manufactured to a number of standards and technical requirements among them
are:
• IEC60974-10applicabletoIndustrialEquipment-genericemissionsandregulations.
• AS1674Safetyinweldingandalliedprocesses.
• AS60974.1/IEC60974-1applicabletoweldingequipmentandassociatedaccessories.
Extensive product design verification is conducted at the manufacturing facility as part of the routine design
and manufacturing process, to ensure the product is safe and performs as specified. Rigorous testing is in-
corporated into the manufacturing process to ensure the manufactured product meets or exceeds all design
specifications.
CIGWELD has been manufacturing and merchandising an extensive equipment range with superior performance,
ultra safe operation and world class quality for more than 30 years and will continue to achieve excellence.
TRANSTIG 170Ti
Manual 0-5278 1-7 GENERAL INFORMATION
1.04 Servicing Hazards
!
WARNING
The symbols shown below are used
throughout this manual to call attention to
and identify possible hazards. When you
see the symbol, watch out, and follow the
related instructions to avoid the hazard.
Only qualified persons should test, main
-
tain, and repair this unit.
Only qualified persons should test, main
-
tain, and repair this unit.
WARNING
ELECTRIC SHOCK can kill.
• Donottouchliveelectricalparts.
• TurnOffweldingpowersourceandwirefeeder
and disconnect and lockout input power using
line disconnect switch, circuit breakers, or by
removing plug from receptacle, or stop engine
before servicing unless the procedure specifi-
cally requires an energized unit.
• Insulateyourselffromgroundbystandingor
working on dry insulating mats big enough to
prevent contact with the ground.
• Donotleaveliveunitunattended.
• Ifthisprocedure requiresandenergizedunit,
have only personnel familiar with and following
standard safety practices do the job.
• When testing a liveunit, use the one-hand
method. Do not put both hands inside unit. Keep
one hand free.
• Disconnect input power conductorsfrom de-
energized supply line BEFORE moving a welding
power source.
SIGNIFICANT DC VOLTAGE exists after removal
of input power on inverters.
• TurnOffinverters,disconnectinputpower,and
discharge input capacitors according to instruc-
tions in Troubleshooting Section before touching
any parts.
WARNING
STATIC (ESD) can damage PC boards.
• PutongroundedwriststrapBEFOREhandling
boards or parts.
• Useproperstatic-proofbagsandboxestostore,
move, or ship PC boards.
WARNING
FIRE OR EXPLOSION hazard.
• Donotplaceuniton,over,ornearcombustible
surfaces.
• Donotserviceunitnearammables.
WARNING
FLYING METAL or DIRT can injure eyes.
• Wearsafety glasseswithsideshieldsorface
shield during servicing.
• Becareful not to short metaltools, parts, or
wires together during testing and servicing.
WARNING
HOT PARTS can cause sever burns.
• Donottouchhotpartsbarehanded.
• Allowcoolingperiodbeforeworkingonequip-
ment.
• To handle not parts, use proper tools and/or
wear heavy, insulated welding gloves and cloth-
ing to prevent burns.
WARNING
EXPLODING PARTS can cause injury.
• Failedpartscanexplodeorcauseotherpartsto
explode when power is applied to inverters.
• Alwayswearafaceshieldandlongsleeveswhen
servicing inverters.
WARNING
SHOCK HAZARD from testing.
• TurnOffweldingpowersourceandwirefeeder
or stop engine before making or changing meter
lead connections.
• Useat least onemeter lead that hasa self-
retaining spring clip such as an alligator clip.
• Readinstructionsfortestequipment.
TRANSTIG 170Ti
GENERAL INFORMATION 1-8 Manual 0-5278
WARNING
FALLING UNIT can cause injury.
• Useliftingeyetoliftunitonly,NOTrunninggear,
gas cylinders, or any other accessories.
• Useequipmentofadequatecapacitytoliftand
support unit.
• Ifusingliftforkstomoveunit,besureforksare
long enough to extend beyond opposite side of
unit.
WARNING
MOVING PARTS can cause injury,
• Keepawayfrommovingpartssuchasfans.
• Keepawayfrompinchpointssuchasdriverolls.
• Have only qualified persons remove doors,
panels, covers, or guards for maintenance as
necessary.
• Keephands,hair,looseclothing,andtoolsaway
from moving parts.
• Reinstalldoors,panels,covers,orguardswhen
maintenance is finished and before reconnecting
input power.
WARNING
OVERUSE can cause OVERHEATING.
• Allowcoolingperiod;followrateddutycycle.
• Reduce current or reduce duty cycle before
starting to weld again.
• Donotblockorlterairowtounit.
!
WARNING
READ INSTRUCTIONS.
• UseTestingBooklet(PartNo.150853)when
servicing this unit.
• ConsulttheOwner’sManualforweldingsafety
precautions.
• Useonlygenuinereplacementpartsfromthe
manufacturer.
TRANSTIG 170Ti
Manual 0-5278 1-9 GENERAL INFORMATION
1.05 EMF Information
Considerations About Welding And The Effects Of Low Frequency Electric And Magnetic Fields
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and
still is some concern about such fields. However, after examining more than 500 studies spanning 17 years
of research, a special blue ribbon committee of the National Research Council concluded that: “The body of
evidence, in the committee’s judgment, has not demonstrated that exposure to power-frequency electric and
magnetic fields is a human-health hazard.” However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you may wish to minimize your exposure
to electromagnetic fields when welding or cutting.
WARNING
H.F. RADIATION can cause interference.
• High-frequency(H.F.)caninterferewithradionavigation,safetyservices,computers,andcommunica-
tions equipment.
• Haveonlyqualiedpersonsfamiliarwithelectronicequipmentinstall,test,andserviceH.F.producing
units.
• Theuseris responsible for having aqualiedelectricianpromptly correct any interferenceproblem
resulting from the installation.
• IfnotiedbytheFCCaboutinterference,stopusingtheequipmentatonce.
• Havetheinstallationregularlycheckedandmaintained.
• Keephigh-frequencysourcedoorsandpanelstightlyshut,keepsparkgapsatcorrectsetting,anduse
grounding and shielding to minimize the possibility of interference.
About Implanted Medical Device
WARNING
MAGNETIC FIELDS can affect Implanted Medical Devices.
• WearersofPacemakersandotherImplantedMedicalDevicesshouldkeepawayfromservicingareas
until consulting their doctor and the device manufacturer.
To reduce magnetic fields in the workplace, use the following procedures:
1. Keep cables close together by twisting or taping them, or using a cable cover.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from operator as practical.
5. Connect work clamp to workpiece as close to the weld as possible.
TRANSTIG 170Ti
GENERAL INFORMATION 1-10 Manual 0-5278
Notes
TRANSTIG 170Ti
Manual 0-5278 2-1 INTRODUCTION
SECTION 2:
INTRODUCTION
2.02 Equipment Identification
The unit’s identification number (specification or
part number), model, and serial number usually ap-
pear on a nameplate attached to the control panel. In
some cases, the nameplate may be attached to the
rear panel. Equipment which does not have a control
panel such as gun and cable assemblies is identified
only by the specification or part number printed on
the shipping container. Record these numbers on the
bottom of page i for future reference.
2.03 Receipt Of Equipment
When you receive the equipment, check it against the
invoice to make sure it is complete and inspect the
equipment for possible damage due to shipping. If
there is any damage, notify the carrier immediately to
file a claim. Furnish complete information concerning
damage claims or shipping errors to the location in
your area listed in the inside back cover of this manual.
Include all equipment identification numbers as
described above along with a full description of the
parts in error.
Move the equipment to the installation site before
un-crating the unit. Use care to avoid damaging the
equipment when using bars, hammers, etc., to un-
crate the unit.
2.01 How To Use This Manual
To ensure safe operation, read the entire manual,
including the chapter on safety instructions and
warnings.
Throughout this manual, the words WARNING,
CAUTION, and NOTE may appear. Pay particular at-
tention to the information provided under these head-
ings. These special annotations are easily recognized
as follows:
!
WARNING
A WARNING gives information regarding
possible personal injury.
CAUTION
A CAUTION refers to possible equipment
damage.
NOTE
A NOTE offers helpful information con
-
cerning certain operating procedures.
Additional copies of this manual may be purchased by
contacting Cigweld at the address and phone number
for your location listed in the inside back cover of this
manual. Include the Owner’s Manual number and
equipment identification numbers.
TRANSTIG 170Ti
INTRODUCTION 2-2 Manual 0-5278
2.04 Symbol Chart
Note that only some of these symbols will appear on your model.
Gas Tungsten Arc
Welding (GTAW)
Air Carbon Arc
Cutting (CAC-A)
Constant Current
Constant Voltage
Or Constant Potential
High Te mperature
Fault Indication
Arc Force
Touch Start (GTAW)
Variable Inductance
Voltage Input
Single Phase
Three Phase
Three Phase Static
Frequency Converter-
Transformer-Rectifier
Dangerous Voltage
Off
On
Panel/Local
Shielded Metal
Arc Welding (SMAW)
Gas Metal Arc
Welding (GMAW)
Increase/Decrease
Circuit Breaker
AC Auxiliary Power
Remote
Duty Cycle
Percentage
Amperage
Voltage
Hertz (cycles/sec)
Frequency
Negative
Positive
Direct Current (DC)
Protective Earth
(Ground)
Line
Line Connection
Auxiliary Power
Receptacle Rating-
Auxiliary Power
Art # A-04937
115V 15A
t
t1
t2
%
X
IPM
MPM
t
V
Fuse
Wire Feed Function
Wire Feed Towards
Workpiece With
Output Voltage Off.
Preflow Time
Postflow Time
Spot Time
Spot Weld Mode
Continuous Weld
Mode
Press to initiate wirefeed and
welding, release to stop.
Purging Of Gas
Inches Per Minute
Meters Per Minute
Disturbance In
Ground System
Welding Gun
Burnback Time
Press and hold for preflow, release
to start arc. Press to stop arc, and
hold for preflow.
4 Step Trigger
Operation
2 Step Trigger
Operation
TRANSTIG 170Ti
Manual 0-5278 2-3 INTRODUCTION
2.05 Description
The Cigweld Transtig 170Ti is a self contained single
phase multi process welding inverter that is capable
of performing MMAW (Stick) and GTAW (HF and Lift
TIG) welding processes. The unit is equipped with an
integrated voltage reduction device (VRD applicable
in stick mode only), digital amperage/voltage meter,
and a host of other features in order to fully satisfy the
broad operating needs of the modern welding profes-
sional. The unit is also fully compliant to Australian
Standard AS 60974.1 and IEC 60974.1.
The Transtig 170Ti provides excellent welding per-
formance across a broad range of applications when
used with the correct welding consumables and
procedures. The following instructions detail how
to correctly and safely set up the machine and give
guidelines on gaining the best efficiency and quality
from the Power Source. Please read these instructions
thoroughly before using the unit.
2.06 User Responsibility
This equipment will perform as per the information
contained herein when installed, operated, maintained
and repaired in accordance with the instructions pro-
vided. This equipment must be checked periodically.
Defective equipment (including welding leads) should
not be used. Parts that are broken, missing, plainly
worn, distorted or contaminated, should be replaced
immediately. Should such repairs or replacements
become necessary, it is recommended that such re-
pairs be carried out by appropriately qualified persons
approved by CIGWELD. Advice in this regard can
be obtained by contacting an Accredited CIGWELD
Distributor.
This equipment or any of its parts should not be al-
tered from standard specification without prior written
approval of CIGWELD. The user of this equipment
shall have the sole responsibility for any malfunction
which results from improper use or unauthorized
modification from standard specification, faulty
maintenance, damage or improper repair by anyone
other than appropriately qualified persons approved
by CIGWELD.
2.07 Transporting Methods
This unit is equipped with a handle for carrying
purposes.
WARNING
ELECTRIC SHOCK can kill. DO NOT TOUCH
live electrical parts. Disconnect input
power conductors from de-energized
supply line before moving the welding
power source.
!
WARNING
FALLING EQUIPMENT can cause serious
personal injury and equipment damage.
Lift unit with handle on top of case.
Use handcart or similar device of adequate capacity.
If using a fork lift vehicle, place and secure unit on a
proper skid before transporting.
2.08 Packaged Items
Transtig 170Ti Mine Spec Plant (Part No. W1007180)
• Transtig170TiMineSpecInverterPowerSource
• Handipakofelectrodes,Satincraft13
• CometProfessionalArgonRegulator/Flowmeter
• TigTorchtype26withexhead,triggerswitch
and 8 pin remote control connection
• TigTorchAccessorykitthatincludes1.6mmand
2.4mm tungstens with collets, collet bodies and
No. 4, 5 & 6 Alumina Nozzles
• ElectrodeHolderwith4mLead
• WorkClampwith4mLead
• ShieldingGasHoseAssembly
• ShoulderStrap
• ProductBag
• OperatingManual
Transtig 170Ti Mine Spec Power Source (Part No.
W1007179)
• Transtig170TiMineSpecInverterPowerSource
• ShieldingGasHoseAssembly
• ShoulderStrap
• OperatingManual
TRANSTIG 170Ti
INTRODUCTION 2-4 Manual 0-5278
Notes
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

ESAB 170Ti Transtig Welding Inverter User manual

Category
Welding System
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI